Whirlpool WD6L27D1B Installation guide

Brand: Whirlpool

Model: WD6L27D1B

Type: Installation guide

SAFETY INFORMATION

Your safety and the safety of others are very important.

We have provided many important safety messages in these instructions and on your product. Always read and

obey all safety messages.

This is the safety alert symbol.

This symbol alerts you to potential hazards that can kill or hurt you and others.

All safety messages will follow the safety alert symbol and either the word “DANGER” or

“WARNING.” These words mean:

You can be killed or seriously injured if you don't immediately

follow instructions.

You can be killed or seriously injured if you don't follow

instructions.

All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell

you what can happen if the instructions are not followed.

Risk of fire or electric shock. Installation of this LED Retrofit Kit assembly

requires a person familiar with the construction and operation of the light

fixture’s/luminaire’s electrical system and the hazard involved. If not

qualified, do not attempt installation. Contact a qualified electrician.

Risk of electric shock. To prevent wiring damage or abrasion, do not

expose wiring to edges of sheet metal or other sharp objects.

Risk of fire or electric shock. Install this kit only in the luminaires (light

fixtures) that have the construction features and dimensions shown in the

photographs and/or drawings included in these Installation Instructions.

SUITABLE FOR DAMP LOCATIONS.

SUITABLE FOR TYPE IC OR NON-IC LUMINAIRES.

MINIMUM LAMP COMPARTMENT DIMENSIONS 102 (DIA) MM X 145 (H) MM

In compliance with CA Prop 65, ETi Solid State Lighting, Inc. provides the following statement due to the customary electronics

components used in this product.

WARNING: This product contains one or more chemicals known to the State of California to cause cancer.

WARNING: This product contains one or more chemicals known to the State of California to cause birth defects or other

reproductive harm.

NOTICE: This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

(1) this device may not cause harmful interference, and (2) this device must accept any interference received,

including interference that may cause undesired operation.

Installation Instructions

Before installing the product or doing any maintenance, make sure to turn off the power supply.

This LED Recessed Light retrofit kit can fit one kind of lamp holder, type E26. Check the existing lamp base before

replacing it to ensure it is an E26 lamp base. If the existing lamp base is not E26, do not install this Recessed Light

retrofit kit. If a thermal protector is in place with the existing fixture, remove it. Check the recessed light fixture

(luminaire) rating to fit the appropriate Recessed Light Kit model number listed below.

Model

Input Voltage (V)

Input Frequency (Hz)

Input Current (mA)

Input Watts (W)

WD6L27D1A

120

WD6L27D1B

120

1. Turn off the power supply. Once power has been turned off, remove the existing bulb and trim, revealing the

socket. Check the dimension of the recessed can to verify the Recessed Light retrofit kit can fit the existing

recessed light fixture (luminaire).

2. Screw the E26 adaptor clockwise into the lamp holder. Tighten.

E26 Adapter

E26 Lamp Holder

3. Connect the male to the female connector.

4. Make sure the trim ring is flush with ceiling. Turn the power supply back on and then turn on the light to verify the

LED recessed light is working properly.

Troubleshooting Guide

Before doing any work on the fixture, disconnect power to the light fixture. Minor problems often can be fixed without

the help of an electrician.

Problem

Possible Cause

Corrective Action

The fixture will not light.

The power is off.

Check to ensure the power supply is on.

The circuit breaker is off.

Check to ensure the circuit breaker is in the on

position.

There is a bad connection.

Check to ensure the male/female connectors

are securely connected.

There is a defective switch.

Contact a qualified electrician.

The fuse blows or circuit breaker trips

when the light is turned on.

The wires are crossed or the

power wire is grounding out.

Check to ensure proper wire connections are

made. Contact a qualified electrician.

Male & Female

Connectors

Trim Ring

Warranty

The manufacturer, Elec-Tech International (HK) Co., Ltd., warrants this LED Lighting Product to be free from defects in

material or workmanship for 6 years from date of purchase, when used as directed. This warranty does not cover

accidents, abuse, acts of God, use in violation of law or electrical standards, or damage from primary side power

sources (e.g., short circuits/power surges). If Product has a defect in materials or workmanship and is returned to the

manufacturer along with proof of purchase and payment receipt, ETi Solid State Lighting Inc. will replace it with the

same or similar Product at no charge or, at its option, refund the original purchase price.

REPLACEMENT OR REFUND IS ETI SOLID STATE LIGHTING INC.’S SOLE WARRANTY OBLIGATION. INCIDENTAL AND

CONSEQUENTIAL DAMAGES ARE EXCLUDED. Some states do not allow the exclusion or limitation of incidental or

consequential damages, so the above limitation or exclusion may not apply to you. This warranty gives you specific

legal rights, and you may also have other rights which vary from state to state. Outside the United States and Canada,

this warranty does not apply.

Keep this warranty, your sales receipt, and proof of purchase/bar code together for future reference. You must

provide proof of purchase for warranty assistance. If you reside in the United States or Canada and your Whirlpool™

LED Lighting product should fail within the first five years of ownership:

1. Call our Customer Service Center at 1-855-305-8974 (toll-free).

2. Give the consultant your complete model number, purchase date, and date of manufacture.

3. You will be responsible for shipping the Product to our return center along with the proof of purchase/bar code and

payment receipt. The LED Lighting product should be properly packaged to avoid damage during transit. We will not

be responsible for damage resulting from improper or inadequate packaging.

4. ETi Solid State Lighting Inc. will return an identical or comparable LED Lighting product to your door free of charge.

If you have questions, call our Customer Service Center at 1-855-305-8974 from anywhere in the U.S. or Canada, or

write to ETi Solid State Lighting Inc., Whirlpool LED Lighting Customer Service, 26650 Renaissance Parkway, Unit # 6,

Cleveland, OH 44128.

Write down the following information about your LED Lighting product to help you obtain assistance if you ever need

it. When calling, please know the purchase date, the model number of your LED Lighting product, and the date of

manufacture. The model number is printed on the product and is a combination of letters and numbers beginning

with the letter “W”. The date code is a five digit number located on the base of the product.

Purchase date......................................................

Model number......................................................

Date of Manufacture ...........................................

International (HK) Co., Ltd., Room 801, Tower 3, China HK City, 33 Canton Road, Tsim Sha Tsui, Kowloon, Hong Kong.

For questions about installation, features, operation/performance, or warranty, call: 1-855-305-8974

Or visit our website at www.WhirlpoolLED.com

Whirlpool WD6L27D1B Installation guide

Whirlpool WD6L27D1B Installation guide

Whirlpool WD6L27D1B Installation guide

Other documents