2. Winworks
  3. 41230631
41230631

Winworks 41230631 Installation guide

  • Hello! I am an AI chatbot trained to assist you with the Winworks 41230631 Installation guide. I’ve already reviewed the document and can help you find the information you need or explain it in simple terms. Just ask your questions, and providing more details will help me assist you more effectively!
GUIDELINES FOR PAINTING PRIMED WINWORKS SHUTTERS
Surface Preparation Specifications
• Shuttersshouldbecleanofanyoil,grease,dirtoranycontaminantsthatmaybepresentfromshippingandhandling.
Amildsolventcleanermaybeused.
• Lightsandingisrecommendedwitha360gritsandpaper,inordertoprovideaslightproleforproperadhesionofpaint.
• Itisimportantthatonedoesnotaggressivelysandthroughorentirelyremovetheprimercoat.
• WerecommendthatyouuseahighqualityUrethane,Alkydor100%Acrylictopcoat.
• Youshouldapplytwotopcoatsinaccordancetothepaintmanufacturers’recommendationsinordertoprovide
appropriatepaintmils.
• Werecommendthatshuttersshouldbepaintedsoonaftersanding.Ifthetimeframeexceedsthirtydays,shuttersmust
beresandedbeforetopcoatisapplied.
Theneedforpropersurfacepreparationpriortopaintingcannotbestressedenough.INCOMPLETE OR IMPROPER SURFACE PREPARATION
IS THE PRIMARY CAUSE OF COATING FAILURES.Thesurfaceshouldbepreparedinwhateverwayisnecessarysothatitwillreceivethepaint
properly.Theconditionofthesurfaceplaysanimportantroleinachievingthedegreeofadhesionrequiredforeffectiveperformance.
Primed Shutters
Contraventanas Imprimadas
INSTALLATION INSTRUCTIONS
• Twelve(12)3
"
inchscrewsareincluded.
• Usefour(4)screwsforeachshutterlessthan49
"
inheight.
• Usesix(6)screwsforeachshutter49
"
orgreaterinheight.
• Drilla1/8
"
diameterpilotholethroughthefaceofthestile1inchfromtheedgeoftheshutterineachcorner.
• Forshutters49
"
orgreaterinheight;alsodrilla1/8
"
diameterpilotholethroughthefaceofthestile1inchfromtheedgeof
eachshutterhalfwayupfromthebottom.
• Placetheshutternexttothewindowandmarkwherethepre-drilledpilotholeslineupagainstthesiding.
• *Drilla1/8
"
diameterholeintothesidingwherethescrewswillpassthroughtheshutterandenterthesiding.
• Placeeachshutternexttothewindowandlineupthepre-drilledpilotholesontheshutterwiththepre-drilledholesinthesiding.
• Insertthescrewintothepre-drilledholesoneachshutteranddrivethescrewintotheshutteruntilthescrewheadisflush
withthefaceoftheshutter.
*
For masonry siding you will need to use a hammer drill to pre-drill a 1/8 " diameter hole.
INSTRUCCIONES DE INSTALACIÓN
• Incluyedoce(12)tornillosde7,62cm.
• Usacuatro(4)tornillosparacadacontraventanademenosde1,24mdealto.
• Usaseis(6)tornillosparacadacontraventanade1,24momásdealto.
• Taladraorificiospilotode31,75mmdediámetroenlacaradeltravesaño,aunadistanciade2,54cmdelbordedecadaesquinadelacontraventana.
• Paracontraventanasde1,24momásdealto,taladratambiénunorificiopilotode31,75mmdediámetroenlacaradeltravesaño,aunadistancia
de2,54cmdelbordedecadacontraventanadesdelaparteinferiorhaciaarribahastalamitad.
• Colocalacontraventanaalladodelaventanaymarcaelpuntodondelosorificiospretaladradossealineanconlamoldura.
• *Taladraunorificiode31,75mmdediámetroenlamoldura,dondelostornillosatravesaránlacontraventanaypenetraránlamoldura.
• Colocacadacontraventanaalladodecadaventanayalinealosorificiospilotodelacontraventanaconlosorificiospretaladradosenlamoldura.
• Insertalostornillosenlosorificiospretaladradosdecadacontraventanayatorníllaloshastaquelacabezadeltornilloestearas
delacontraventana.
* Para molduras de mampostería necesitarás usar un taladro percutor para pretaladrar el orificio de 31,75 mm de diámetro.
INSTRUCCIONES PARA PINTAR LAS CONTRAVENTANAS IMPRIMADAS WINWORKS
EspecificacionesparalaPreparacióndelaSuperficie
• Lascontraventanasdebenestarlimpiasdetodoaceite,grasa,suciedadocontaminantequepudieranestarpresentesdebidoalmanejoyelenvío.
Puedeusarseunlimpiadorsolventesuave.
• Serecomiendalijarligeramenteconpapeldelijadegrano360,paracrearunperfiladecuadoparaquelapinturaseadhiera.
• Esimportantenolijarenérgicamenteoremoverlacapadeimprimador.
• RecomendamoselusodeunrevestimientodeUretano,Álcideo100%deAcrílicodealtacalidad.
• Debesaplicardoscapassuperioressegúnlasrecomendacionesdelfabricantedelapinturaparalograrelespesoradecuado.
• Recomendamosquelascontraventanassepintenlomásprontoposibledespuésdelijar.Sipasaranmásdetreintadíassedebenvolveralijar
antesdeaplicarlacapasuperior.
Nosedebesubestimarlaimportanciadepreparararlasuperficieantesdepintar.LAPREPARACIÓNINADECUADAOINCOMPLETADELASUPERFICIE
ESLACAUSAPRINCIPALDEQUEELREVESTIMIENTOFALLE.Lasuperficiedebeprepararsesegúnseanecesarioparaquelapinturaseadhiera
apropiadamente.Lacondicióndelasuperficiejuegaunpapelimportanteparalograrungradodeadhesiónquepermitaunrendimientoefectivo.
/