HQ Power VDPL300LS User manual

VDPL300LS
Brand
HQ Power
Model
VDPL300LS
Category
Stroboscopes & disco lights
Type
User manual
Page is loading ...
VDPL300LS
V. 02 – 22/08/2014 2 ©Velleman nv
ENGLISH
NEDERLANDS
1
1
Bevestigingsoog
2
2
Microfoon
3
3
Voeding
4
4
Zekeringhouder
5
5
Voedingsuitgang
6
6
Gevoeligheidsknop voor microfoon
7
display
7
Programmaknoppen met LED-
display
8
8
DMX-uitgang
9
9
DMX-ingang
FRANCAIS
ESPAÑOL
1
1
ojete de fijación
2
2
micrófono
3
3
entrada alimentación
4
4
Portafusibles
5
5
salida de alimentación
6
6
ajuste para la sensibilidad del
micrófono
7
afficheur LED
7
botones de programación con
pantalla LED
8
8
salida DMX
9
9
entrada DMX
DEUTSCH
1
6
Regler für die Mikrofon-
Empfindlichkeit
2
7
Programmiertasten mit LED-Display
3
8
DMX-Ausgang
4
9
DMX-Eingang
5
2
5
3
6
7
8
1
4
9
VDPL300LS
V. 02 – 22/08/2014 3 ©Velleman nv
USER MANUAL
1. Introduction
To all residents of the European Union
Important environmental information about this product
This symbol on the device or the package indicates that disposal of the device after its lifecycle could
harm the environment. Do not dispose of the unit (or batteries) as unsorted municipal waste; it
should be taken to a specialized company for recycling. This device should be returned to your
distributor or to a local recycling service. Respect the local environmental rules.
If in doubt, contact your local waste disposal authorities.
Thank you for choosing HQPower™! Please read the manual thoroughly before bringing this device into service.
If the device was damaged in transit, don't install or use it and contact your dealer.
2. Safety Instructions
• Damages caused by the disregard of this user manual are not subject to warranty.
• If the device has been exposed to important temperature fluctuation (e.g. after transportation), do not
switch it on immediately. The arising condensation water might damage your device. Leave the device
switched off until it has reached room temperature.
• Make sure that there are no obvious transport damages. Should you notice any damages on the A/C
connection cable or on the casing, do not take the device into operation and immediately consult your
local dealer.
• This device falls under protection-class I. The power plug must only be plugged into a protection class I
outlet. The voltage and frequency must exactly be the same as stated on the device. Wrong voltages or
power outlets can lead to the destruction of the device and to fatal electrical shock.
• Always plug in the power plug last. The power plug must always be inserted without force. Make sure
that the plug is tightly connected with the outlet.
• Never let the power cord come into contact with other cables. Handle the power cord and all
connections with the mains with particular caution. Never touch them with wet hands, as this could lead
to fatal electrical shock.
• Never modify, bend, strain mechanically, put pressure on, pull or heat up the power cord. Never
operate next to sources of heat or cold. Disregard can lead to power cord damages, fire or fatal
electrical shock.
• The cable insert or the female part in the device must never be strained. There must always be
sufficient cable to the device. Otherwise, the cable may be damaged which may lead to fatal damage.
• Make sure that the power cord is never crimped or damaged by sharp edges. Check the device and the
power cord from time to time.
• If extension cords are used, make sure that the core diameter is sufficient for the required power
consumption of the device. All warnings concerning the power cords are also valid for possible
extension cords.
• Always disconnect from the mains, when the device is not in use or before cleaning it. Only handle the
power cord by the plug. Never pull out the plug by tugging the power cord. Otherwise, the cable or plug
can be damaged leading to fatal electrical shock. If the power plug or the power switch is not
accessible, the device must be disconnected via the mains.
• If the power plug or the device is dusty, the device must be taken out of operation, disconnected and
then be cleaned with a dry cloth. Dust can reduce the insulation which may lead to fatal electrical
shock. More severe dirt in and at the device should only be removed by a specialist.
• There must never enter any liquid into power outlets, extension cords or any holes in the housing of the
device. If you suppose that also a minimal amount of liquid may have entered the device, it must
immediately be disconnected. This is also valid, if the device was exposed to high humidity. Also if the
device is still running, the device must be checked by a specialist if the liquid has reduced any
insulation. Reduced insulation can cause fatal electrical shock.
• There must never be any objects entering into the device. This is especially valid for metal parts. If any
metal parts like staples or coarse metal chips enter into the device, the device must be taken out of
operation and disconnected immediately. Malfunction or short-circuits caused by metal parts may cause
fatal injuries.
• HEALTH HAZARD. Never look directly into the light source, as sensitive persons may suffer an epileptic
shock (especially meant for epileptics).
• Keep away from children and unauthorized people.
• Never leave the device running unattended.
VDPL300LS
V. 02 – 22/08/2014 4 ©Velleman nv
3. General Guidelines
Refer to the Velleman® Service and Quality Warranty on the last pages of this manual.
• This device is a lighting effect for creating decorative effects. This product is only allowed to be
operated with an alternating voltage of 230 V, 50 Hz and was designed for indoor use only.
• This device is designed for professional use, e.g. on stages, in discotheques, theatres etc.
• Lighting effects are not designed for permanent operation. Consistent operation breaks will ensure that
the device will serve you for a long time without defects.
• Do not shake the device. Avoid brute force when installing or operating the device.
• When choosing the installation location, please make sure that the device is not exposed to extreme
heat, moisture or dust. There should not be any cables lying around.
• This device must never be operated or stockpiled in surroundings where splash water, rain, moisture or
fog may harm the device. Moisture or very high humidity can reduce the insulation and lead to fatal
electrical shocks. When using smoke machines, make sure that the device is never exposed to the
direct smoke jet and is installed in a distance of 0.5 meters between smoke machine and device. The
room must only be saturated with an amount of smoke that the visibility will always be more than 10
meters.
• The ambient temperature must always be between -5° C and +45° C. Keep away from direct insulation
(particularly in cars) and heaters.
• The relative humidity must not exceed 50 % with an ambient temperature of 45° C. This device must
only be operated in an altitude between -20 and 2000 m over NN.
• Always disconnect the device during thunderstorms.
• This device is only allowed for an installation via the mounting bracket. In order to safeguard sufficient
ventilation, leave 50 cm of free space around the device.
• The housing must never touch surrounding surfaces or objects.
• Operate the device only after having become familiarized with its functions. Do not permit operation by
persons not qualified for operating the device. Most damages are the result of unprofessional operation.
• Never use solvents or aggressive detergents in order to clean the device. Rather use a soft and damp
cloth.
• Use the original packaging if the device is to be transported. Make sure that you pack the device in the
original state.
• Never remove the serial barcode from the device as this would make the guarantee void.
• If this device will be operated in any way different to the one described in this manual, the product may
suffer damages and the guarantee becomes void. Furthermore, any other operation may lead to
dangers like short- circuit, burns, electric shock, crash etc.
4. Features
• a real eye catcher: 5 LED lenses in pentagon form
• works in stand-alone mode, master/slave, sound control via built-in microphone or DMX controlled
• DMX channels selectable in 2- or 3-channel mode
• easy menu setting via LED display with 4 buttons
• equipped with 160 bright 5mm LEDs
• linkable power connection, connect up to 8 units
5. Installation
• Consider the EN 60598-2-17and the respective national standards during the installation. The
installation must only be carried out by an authorized dealer.
• Make sure the installation can hold 10 times the weight for 1 hour without any harming deformation.
• The installation must always be secured with a secondary safety attachment, e.g. an appropriate catch
net. This secondary safety attachment must be constructed in a way that no part of the installation can
fall down if the main attachment fails.
• When rigging, derigging or servicing the device staying in the area below the installation place, on
bridges, under high working places and other endangered areas is forbidden.
• The device should be installed outside areas where persons may walk by or be seated.
• IMPORTANT. OVERHEAD RIGGING REQUIRES EXTENSIVE EXPERIENCE, including (but not limited to)
calculating working load limits, installation material being used, and periodic safety inspection of all
installation material and the device. If you lack these qualifications, do not attempt the installation
yourself, but instead use a professional structural rigger. Improper installation can result in bodily
injury and or damage to property.
VDPL300LS
V. 02 – 22/08/2014 5 ©Velleman nv
• The device has to be installed out of the reach of people.
• If the device shall be lowered from the ceiling or high joists, professional trussing systems have to be
used. The device must never be fixed swinging freely in the room.
• Caution: Devices in hanging installations may cause severe injuries when crashing down. If you have
doubts concerning the safety of a possible installation, do NOT install the device.
• When installing the device, make sure there is no highly inflammable material (decoration articles, etc.)
within a distance of min. 0.5 m.
• Mount the device to your trussing system using an appropriate clamp. For overhead use, always install
an appropriate safety bond.
• You must only use safety bonds complying with DIN 56927, quick links complying with DIN 56927,
shackles complying with DIN EN 1677-1 and BGV C1 carbines. The safety bonds, quick links, shackles
and the carbines must be sufficiently dimensioned and used correctly in accordance with the latest
industrial safety regulations (e. g. BGV C1, BGI 810-3).
• For overhead rigging in public or industrial areas, a series of safety instructions have to be followed that
this manual can only give in part. The operator must therefore inform himself on the current safety
instructions and consider them.
• The manufacturer cannot be made liable for damages caused by incorrect installations or insufficient
safety precautions.
• Pull the safety bond through the attachment eyelet and over the trussing system or a safe fixation spot.
Insert the end in the quick link and tighten the safety screw.
• The maximum drop distance must never exceed 20 cm.
• A safety bond which already held the strain of a crash or which is defective must not be used again.
• Adjust the desired inclination angle via the mounting bracket and tighten the fixation screws.
5.1 DMX control
• The wires must not come into contact with each other, otherwise the devices will not work at all, or will
not work properly.
• The starting address depends upon which controller is being used.
• Only use a DMX cable and 3-pin XLR plugs and connectors in order to connect the controller with the
device or one device with another.
Wiring diagram of the XLR connection
DMX output
DMX input
1 Ground
1 Ground
2 Signal (-)
2 Signal (-)
3 Signal (+)
3 Signal (+)
• If you are using controllers with this XRL connection type, you can connect the DMX output of the
controller directly to the DMX input of the first device in the DMX chain. If you wish to connect DMX
controllers with other XLR outputs, you need to use adapter cables.
Building a serial DMX chain:
• Connect the DMX output of the first device in the DMX chain with the DMX input of the next device.
Always connect one output with the input of the next device until all devices are connected.
• Caution: At the last device, the DMX cable has to be terminated. Plug the terminator with a 120 resistor
between Signal (–) and Signal (+) in the DMX output of the last device.
Connection between devices
• On the rear panel, there is an IEC socket (Power Out). Connect the output with the input of the next
device until all devices are connected.
• Attention: It is recommended to renew the connection with the power mains after every 8 devices.
Connection with the mains
Connect the device to the mains with the enclosed power supply cable.
The occupation of the connection cables is as follows:
VDPL300LS
V. 02 – 22/08/2014 6 ©Velleman nv
Cable
Pin
International
Brown
Live
L
Blue
Neutral
N
Yellow/Green
Earth
The earth has to be connected.
If the device will be directly connected with the local power supply network, a disconnection switch with a
minimum opening of 3 mm at every pole has to be included in the permanent electrical installation.
The device must only be connected with an electric installation carried out in compliance with the IEC-
standards. The electric installation must be equipped with a Residual Current Device (RCD) with a maximum
fault current of 30 mA.
Lighting effects must not be connected to dimming-packs.
6. Operation
After you connected the device to the mains, the device starts running.
The LED display lights up and you can now choose the desired settings via the buttons MODE, ENTER, UP and
DOWN.
6.1 Auto mode
In Auto Mode the internal program is called up automatically in a continuous loop.
1. Press the MODE button until the LED display shows "AUTO". Press the ENTER button to confirm.
2. To set the desired program speed, press the MODE button until the LED display shows "s---".
3. The desired speed (s001 - s100, increasing) can be selected via the UP or DOWN buttons.
4. Press the ENTER button to confirm.
6.2 Sound mode
1. Press the MODE button until the LED display shows "snd".
2. Press the ENTER button to confirm.
6.3 Master/Slave mode
In master/slave mode, several devices can be synchronized and controlled by one master device.
1. On the rear panel of the device you can find an XLR jack and an XLR plug, which can be used for connecting
several devices.
2. Choose the device which is to control the effects. This device then works as master device and controls all
other slave devices, which are to be connected to the master device via a DMX-cable. Connect the OUT jack
with the IN plug of the next device.
3. Set the Master device to Auto or Sound Mode and set each Slave device to the same DMX address "d001".
6.4 DMX mode
The LED display allows you to assign the DMX device address, which is defined as the first channel from which
the device will respond to the controller.
Controlling
1. After having addressed the device, you may now start operating it via your lighting controller.
Note: It’s necessary to insert the XLR termination plug (with 120 Ohm) in the last lighting in the link in order to
ensure proper transmission on the DMX data link.
Addressing
1. Press the MODE button until the display shows "512" then press the ENTER button to confirm.
2. Set the desired address via the UP or DOWN buttons (001 - 512).
3. Press the ENTER button again to confirm and to select a DMX Channel Mode.
DMX Channel Selection: Choosing a DMX Channel Mode
1. After having set the desired address(es) and pressed ENTER, you can now choose a DMX Channel Mode. (2
CH or 3 CH).
2. Set the desired mode via the UP or DOWN buttons.
3. Press the ENTER button again to confirm and to exit the DMX Mode.
See the following DMX protocol graphics for the respective channel values.
VDPL300LS
V. 02 – 22/08/2014 7 ©Velleman nv
6.5 DMX protocol
2-Channel Mode
Channel 1 - Auto Programs
Value
Function
000 – 015
Blackout
016 – 089
Auto program slow
090 – 164
Auto program middle
165 – 240
Auto program fast
241 – 255
Auto program sound control
Channel 2 – Strobe
Value
Function
000 – 000
No function
001 - 255
Flash, with increasing speed
3-Channel Mode
Channel 1 - Auto Programs
Value
Function
000 – 009
Blackout
010 – 019
Auto program 1
020 – 029
Auto program 2
030 – 039
Auto program 3
040 – 049
Auto program 4
050 – 059
Auto program 5
060 – 069
Auto program 6
070 – 079
Auto program 7
080 – 089
Auto program 8
090 – 099
Auto program 9
100 – 109
Auto program 10
110 – 119
Auto program 11
120 – 129
Auto program 12
130 – 139
Auto program 13
140 – 149
Auto program 14
150 – 159
Auto program 15
160 – 169
Auto program 16
170 – 179
Auto program 17
180 – 189
Auto program 18 (random)
190 – 255
Sound control
Channel 2 – Speed
Value
Function
000 - 255
Increasing speed of the program settings under channel 1 (010 - 189)
Channel 3 – Strobe
Value
Function
000 – 009
No function
010 - 255
Flash, with increasing speed
VDPL300LS
V. 02 – 22/08/2014 8 ©Velleman nv
7. Cleaning and maintenance
Disconnect the device from mains before starting maintenance operation.
The operator has to make sure that safety-relating and machine-technical installations are approved by an
expert before taking into operation for the first time and after changes before taking into operation another
time.
The operator has to make sure that safety-relating and machine-technical installations are inspected by an
expert after every four years in the course of an acceptance test.
The operator has to make sure that safety-relating and machine-technical installations are inspected by a
skilled person once a year.
The following points have to be considered during the inspection:
• All screws used for installing the devices or parts of the device have to be tightly connected and must
not be corroded.
• There must not be any deformations on housings, fixations and installation spots (ceiling, suspension,
trussing).
• The electric power supply cables must not show any damages, material fatigue (e.g. porous cables) or
sediments. Further instructions depending on the installation spot and usage have to be adhered by a
skilled installer and any safety problems have to be removed.
We recommend a frequent cleaning of the device. Use a soft lint-free and moistened cloth. Never use alcohol or
solvents.
There are no serviceable parts inside the device except for the fuse. Maintenance and service operations are
only to be carried out by authorized dealers.
7.1 Replacing the fuse
If the fuse of the device blows, only replace it with a fuse of same type and rating (see "Technical
Specifications").
1. Disconnect the device from the mains before starting maintenance operation.
2. Open the fuse holder on the rear panel with a fitting screwdriver.
3. Remove the old fuse and insert a new one.
4. Screw the fuse holder back into the housing.
Should you need any spare parts, use genuine parts.
If the power supply cable of this device becomes damaged, it has to be replaced by a special power supply
cable available at your dealer.
8. Technical Specifications
power supply
230Vac/50Hz
power consumption
20W
fuse
T1A, 250V
DMX connection
3-pin XLR in- and output
number of LEDs
160pcs (40pcs of each colour)
beam angle
46°
dimensions
240 x 325 x 345mm
weight
3.5kg
Use this device with original accessories only. Velleman nv cannot be held responsible in the event
of damage or injury resulted from (incorrect) use of this device.
For more info concerning this product and the latest version of this manual, please visit our website
www.hqpower.eu.
The information in this manual is subject to change without prior notice.
© COPYRIGHT NOTICE
The copyright to this manual is owned by Velleman nv. All worldwide rights reserved.
No part of this manual or may be copied, reproduced, translated or reduced to any electronic medium or
otherwise without the prior written consent of the copyright holder.
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Velleman® Service and Quality Warranty
Since its foundation in 1972, Velleman® acquired extensive
experience in the electronics world and currently distributes its
products in over 85 countries.
All our products fulfil strict quality requirements and legal stipulations
in the EU. In order to ensure the quality, our products regularly go
through an extra quality check, both by an internal quality
department and by specialized external organisations. If, all
precautionary measures notwithstanding, problems should occur,
please make appeal to our warranty (see guarantee conditions).
General Warranty Conditions Concerning Consumer Products
(for EU):
• All consumer products are subject to a 24-month warranty on
production flaws and defective material as from the original date of
purchase.
• Velleman® can decide to replace an article with an equivalent
article, or to refund the retail value totally or partially when the
complaint is valid and a free repair or replacement of the article is
impossible, or if the expenses are out of proportion.
You will be delivered a replacing article or a refund at the value of
100% of the purchase price in case of a flaw occurred in the first
year after the date of purchase and delivery, or a replacing article at
50% of the purchase price or a refund at the value of 50% of the
retail value in case of a flaw occurred in the second year after the
date of purchase and delivery.
• Not covered by warranty:
- all direct or indirect damage caused after delivery to the article
(e.g. by oxidation, shocks, falls, dust, dirt, humidity...), and by the
article, as well as its contents (e.g. data loss), compensation for loss
of profits;
- consumable goods, parts or accessories that are subject to an aging
process during normal use, such as batteries (rechargeable, non-
rechargeable, built-in or replaceable), lamps, rubber parts, drive
belts... (unlimited list);
- flaws resulting from fire, water damage, lightning, accident, natural
disaster, etc.…;
- flaws caused deliberately, negligently or resulting from improper
handling, negligent maintenance, abusive use or use contrary to the
manufacturer’s instructions;
- damage caused by a commercial, professional or collective use of
the article (the warranty validity will be reduced to six (6) months
when the article is used professionally);
- damage resulting from an inappropriate packing and shipping of the
article;
- all damage caused by modification, repair or alteration performed
by a third party without written permission by Velleman®.
• Articles to be repaired must be delivered to your Velleman® dealer,
solidly packed (preferably in the original packaging), and be
completed with the original receipt of purchase and a clear flaw
description.
• Hint: In order to save on cost and time, please reread the manual
and check if the flaw is caused by obvious causes prior to presenting
the article for repair. Note that returning a non-defective article can
also involve handling costs.
• Repairs occurring after warranty expiration are subject to shipping
costs.
• The above conditions are without prejudice to all commercial
warranties.
The above enumeration is subject to modification according to
the article (see article’s manual).
Velleman® service- en kwaliteitsgarantie
Velleman® heeft sinds zijn oprichting in 1972 een ruime ervaring
opgebouwd in de elektronicawereld en verdeelt op dit moment
producten in meer dan 85 landen. Al onze producten beantwoorden
aan strikte kwaliteitseisen en aan de wettelijke bepalingen geldig in
de EU. Om de kwaliteit te waarborgen, ondergaan onze producten op
regelmatige tijdstippen een extra kwaliteitscontrole, zowel door onze
eigen kwaliteitsafdeling als door externe gespecialiseerde
organisaties. Mocht er ondanks deze voorzorgen toch een probleem
optreden, dan kunt u steeds een beroep doen op onze waarborg (zie
waarborgvoorwaarden).
Algemene waarborgvoorwaarden consumentengoederen
(voor Europese Unie):
• Op alle consumentengoederen geldt een garantieperiode van 24
maanden op productie- en materiaalfouten en dit vanaf de
oorspronkelijke aankoopdatum.
• Indien de klacht gegrond is en een gratis reparatie of vervanging
van een artikel onmogelijk is of indien de kosten hiervoor buiten
verhouding zijn, kan Velleman® beslissen het desbetreffende artikel
te vervangen door een gelijkwaardig artikel of de aankoopsom van
het artikel gedeeltelijk of volledig terug te betalen. In dat geval krijgt
u een vervangend product of terugbetaling ter waarde van 100% van
de aankoopsom bij ontdekking van een gebrek tot één jaar na
aankoop en levering, of een vervangend product tegen 50% van de
kostprijs of terugbetaling van 50 % bij ontdekking na één jaar tot 2
jaar.
• Valt niet onder waarborg:
- alle rechtstreekse of onrechtstreekse schade na de levering
veroorzaakt aan het toestel (bv. door oxidatie, schokken, val, stof,
vuil, vocht...), en door het toestel, alsook zijn inhoud (bv. verlies van
data), vergoeding voor eventuele winstderving.
- verbruiksgoederen, onderdelen of hulpstukken die onderhevig zijn
aan veroudering door normaal gebruik zoals bv. batterijen (zowel
oplaadbare als niet-oplaadbare, ingebouwd of vervangbaar), lampen,
rubberen onderdelen, aandrijfriemen... (onbeperkte lijst).
- defecten ten gevolge van brand, waterschade, bliksem, ongevallen,
natuurrampen, enz.
- defecten veroorzaakt door opzet, nalatigheid of door een
onoordeelkundige behandeling, slecht onderhoud of abnormaal
gebruik of gebruik van het toestel strijdig met de voorschriften van
de fabrikant.
- schade ten gevolge van een commercieel, professioneel of collectief
gebruik van het apparaat (bij professioneel gebruik wordt de
garantieperiode herleid tot 6 maand).
- schade veroorzaakt door onvoldoende bescherming bij transport
van het apparaat.
- alle schade door wijzigingen, reparaties of modificaties uitgevoerd
door derden zonder toestemming van Velleman®.
• Toestellen dienen ter reparatie aangeboden te worden bij uw
Velleman®-verdeler. Het toestel dient vergezeld te zijn van het
oorspronkelijke aankoopbewijs. Zorg voor een degelijke verpakking
(bij voorkeur de originele verpakking) en voeg een duidelijke
foutomschrijving bij.
• Tip: alvorens het toestel voor reparatie aan te bieden, kijk nog
eens na of er geen voor de hand liggende reden is waarom het
toestel niet naar behoren werkt (zie handleiding). Op deze wijze kunt
u kosten en tijd besparen. Denk eraan dat er ook voor niet-defecte
toestellen een kost voor controle aangerekend kan worden.
• Bij reparaties buiten de waarborgperiode zullen transportkosten
aangerekend worden.
• Elke commerciële garantie laat deze rechten onverminderd.
Bovenstaande opsomming kan eventueel aangepast worden
naargelang de aard van het product (zie handleiding van het
betreffende product).
Garantie de service et de qualité Velleman®
Depuis 1972, Velleman® a gagné une vaste expérience dans le
secteur de l’électronique et est actuellement distributeur dans plus de
85 pays.
Tous nos produits répondent à des exigences de qualité rigoureuses
et à des dispositions légales en vigueur dans l’UE. Afin de garantir la
qualité, nous soumettons régulièrement nos produits à des contrôles
de qualité supplémentaires, tant par notre propre service qualité que
par un service qualité externe. Dans le cas improbable d’un défaut
malgré toutes les précautions, il est possible d’invoquer notre
garantie (voir les conditions de garantie).
Conditions générales concernant la garantie sur les produits
grand public (pour l’UE) :
• tout produit grand public est garanti 24 mois contre tout vice de
production ou de matériaux à dater du jour d’acquisition effective ;
• si la plainte est justifiée et que la réparation ou le remplacement
d’un article est jugé impossible, ou lorsque les coûts s’avèrent
disproportionnés, Velleman® s’autorise à remplacer ledit article par
un article équivalent ou à rembourser la totalité ou une partie du prix
d’achat. Le cas échéant, il vous sera consenti un article de
remplacement ou le remboursement complet du prix d’achat lors
d’un défaut dans un délai de 1 an après l’achat et la livraison, ou un
article de remplacement moyennant 50% du prix d’achat ou le
remboursement de 50% du prix d’achat lors d’un défaut après 1 à 2
ans.
• sont par conséquent exclus :
- tout dommage direct ou indirect survenu à l’article après livraison
(p.ex. dommage lié à l’oxydation, choc, chute, poussière, sable,
impureté…) et provoqué par l’appareil, ainsi que son contenu (p.ex.
perte de données) et une indemnisation éventuelle pour perte de
revenus ;
- toute pièce ou accessoire nécessitant un remplacement causé par
un usage normal comme p.ex. piles (rechargeables comme non
rechargeables, intégrées ou remplaçables), ampoules, pièces en
caoutchouc, courroies… (liste illimitée) ;
- tout dommage qui résulte d’un incendie, de la foudre, d’un
accident, d’une catastrophe naturelle, etc. ;
- out dommage provoqué par une négligence, volontaire ou non, une
utilisation ou un entretien incorrect, ou une utilisation de l’appareil
contraire aux prescriptions du fabricant ;
- tout dommage à cause d’une utilisation commerciale,
professionnelle ou collective de l’appareil (la période de garantie sera
réduite à 6 mois lors d’une utilisation professionnelle) ;
- tout dommage à l’appareil qui résulte d’une utilisation incorrecte ou
différente que celle pour laquelle il a été initialement prévu comme
décrit dans la notice ;
- tout dommage engendré par un retour de l’appareil emballé dans
un conditionnement non ou insuffisamment protégé.
- toute réparation ou modification effectuée par une tierce personne
sans l’autorisation explicite de SA Velleman® ; - frais de transport de
et vers Velleman® si l’appareil n’est plus couvert sous la garantie.
• toute réparation sera fournie par l’endroit de l’achat. L’appareil doit
nécessairement être accompagné du bon d’achat d’origine et être
dûment conditionné (de préférence dans l’emballage d’origine avec
mention du défaut) ;
• tuyau : il est conseillé de consulter la notice et de contrôler câbles,
piles, etc. avant de retourner l’appareil. Un appareil retourné jugé
défectueux qui s’avère en bon état de marche pourra faire l’objet
d’une note de frais à charge du consommateur ;
• une réparation effectuée en-dehors de la période de garantie fera
l’objet de frais de transport ;
• toute garantie commerciale ne porte pas atteinte aux conditions
susmentionnées.
La liste susmentionnée peut être sujette à une
complémentation selon le type de l’article et être mentionnée
dans la notice d’emploi.
Page is loading ...
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35

HQ Power VDPL300LS User manual

VDPL300LS
Brand
HQ Power
Model
VDPL300LS
Category
Stroboscopes & disco lights
Type
User manual
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

in other languages

Related papers

Other documents