Zelmer Aquawelt 919.0 SP User manual

919-001

www.zelmer.pl

www.zelmer.com

www.zelmer.pl

www.zelmer.com

Odkurzacz

Vacuum cleaner

Aquawelt

Wariant kolorystyczny Colour variant

919.5 SK 919.0 SP 919.0 ST

A

21

23

22

21

14

24

15

16

17

31

33

35

34

32

25

28

29

30

19

26

27

13

12

4

3

20

18

7

10

11

9

8

6

5

A

B

PL

CZ

SK

HU

RO

RU

BG

UA

EN

PL

CZ

SK

HU

RO

RU

BG

UA

EN

PL

CZ

SK

HU

RO

RU

BG

UA

EN

instrukcja

użytkowania

user

manual

INSTRUKCJA UŻYTKOWANIA

ODKURZACZ

Typ 919

NÁVOD K POUŽITÍ

VYSAVAČ

Typ 919

ИНСТРУКЦИЯ ПО ЭКСПЛУАТАЦИИ

ПЫЛЕСОС

Tип 919

LIETOŠANAS INSTRUKCIJA

PUTEKĻU SŪCĒJS

Tips 919

NÁVOD NA OBSLUHU

VYSÁVAČ

Typ 919

ИНСТРУКЦИЯ ЗА УПОТРЕБА

ПРАХОСМУКАЧКА

Тип 919

KASUTUSJUHEND

TOLMUIMEJA

Tüüp 919

HASZNÁLATI UTASÍTÁS

PORSZÍVÓK

919 Típus

ІНСТРУКЦІЯ З КОРИСТУВАННЯ

ПИЛОСОС

Тип 919

USER MANUAL

VACUUM CLEANER

Type 919

INSTRUCŢIUNI DE UTILIZARE

ASPIRATORUL

Tip 919

VARTOJIMO INSTRUKCIJA

DULKIŲ SIURBLYS

Tipas 919

BEDIENUNGSANLEITUNG

BODENSTAUBSAUGER

Typ 919

6–10

11–15

16–20

21–25

26–30

52–55

57–61

62–66

67–71

PL

SK

CZ

HU

RU

RO

UA

BG

EN

LT DE

LV

ET

31–35

36–41

42–46

47–51

Odkurzacz

Vacuum cleaner

Aquawelt

www.goldenservice.zelmer.com

Page is loading ...

62

Dear Customers!

Please read this instruction manual carefully. Pay special

attention to important safety instructions. Keep this instruction

manual for future reference.

Important safety instructions

Connect the vacuum cleaner only to a 230 V mains

●

supply equipped with a 16 A fuse.

Do not unplug by pulling on cord.

●

Do not operate the appliance if it has a damaged cord or

●

if the housing is visibly damaged.

If the supply cord is damaged, it must be replaced by

the manufacturer, a service agent or a qualied person

in order to avoid a hazard.

The appliance can only be repaired by qualied service

personnel. Improper servicing may cause a serious

hazard to the user. In case of defects please contact

a qualied service center.

Do not allow the plug to have contact with water.

●

Do not touch the appliance with wet hands when it is

●

connected to the mains supply.

Do not run the vacuum cleaner or the brushes over the

●

cord, it may cause damage to the cord insulation.

Always unplug the appliance before cleaning, assembling

●

or dismantling.

Switch off the appliance before changing attachments or

●

before contact with movable parts.

Do not use the vacuum cleaner to clean people or

●

animals, pay special attention to keep the nozzles away

from eyes and ears.

Do not pick up: matches, cigarette butts, hot ash. Avoid

●

picking up sharp objects.

Do not vacuum ne dust such as: our, cement, gypsum,

●

toners for printers and copy machines etc.

Do not pick up corrosive and toxic materials, petrol,

●

kerosene and other ammable or explosive liquids.

EN

ATTENTION! The pump may only be switched on when

the cleaning liquid container is lled with the solution

of cleaning liquid and water. The lack of cleaning liquid

is manifested in a loud operation of the pump.

During operation pay attention not to knock the vacuum

●

cleaner over or to spill water on the appliance.

Do not expose the vacuum cleaner to atmospheric

●

conditions (rain, frost).

Do not use the vacuum cleaner without the foam lter

●

installed in the lter unit.

Do not leave a switched on and operating vacuum

●

cleaner unattended.

This appliance is not intended for use by persons

●

(including children) with reduced physical, sensory or

mental capabilities, or lack of experience and knowledge,

unless they have been given supervision or instruction

concerning use of the appliance by a person responsible

for their safety.

Children should be supervised to ensure that they do not

●

play with the appliance.

ATTENTION! The vacuum cleaner may only operate

in a natural position i.e. when it is placed with four

wheels on the surface.

Technical parameters

The type of the vacuum cleaner and the technical parameters

are indicated on the rating label. Mains protection 16 A.

Does not interfere with radio and TV reception.

Does not require grounding .

ZELMER vacuum cleaners meet the requirements of the

applicable norms.

The appliance is in conformity with the requirements of the

directives:

Low voltage appliance (LVD) – 2006/95/EC. –

Electromagnetic compatibility (EMC) – 2004/108/EC. –

Noise level: 80 dB/A.

The appliance was marked by a CE sign on the rating label.

VACUUM CLEANER 919 TYPES

Workmanship and equipment

option:

Type

Dust bag / amount

Outlet lter

Suction hose

Telescopic suction tubes

Combination brush with small

item separator

Small nozzle

Crevice nozzle

Small brush

Parquet brush

Turbo brush

Large atomizing nozzle

Small atomizing nozzle

Water pick up nozzle

Electronic power control

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15

919.0 ST SAFBAG 2 pcs. HEPA

+ + + + + + + + + + + +

919.0 SP SAFBAG 2 pcs. HEPA

+ + + + + + + - + + + +

919.5 SK SAFBAG 2 pcs. HEPA

+ + + + + + - - + + + -

63

Appliance features

The vacuum cleaner 919 is intended to pick up dirt from

oors, carpets, ceramic tiles, slots in wood paneling, skirting

boards, heaters. The vacuum cleaner is also used to vacuum

furniture, curtains, to pick up liquids and to wet clean tiles,

oorings, carpets, tted carpets and upholstery.

Appliance elements

1

Handle

2

Container lid opening button

3

Plug and cord

4

Accessory compartment

5

Pump operation indicator

6

Pump switch

7

ON/OFF button

8

Power adjustment button +/- (type 919.0)

9

Power level indicator (type 919.0)

10

Cord rewind button

11

Clogged air inlet indicator (type 919.0)

12

Parquet brush (type 919.0)

13

The vacuum cleaner is equipped with only one type of

suction brush (A or B)

A

Suction-brush

B

Combination brush with small item separator

14

Turbo brush (type 919.0 ST)

15

Small brush

16

Small nozzle

17

Crevice nozzle

18

Telescopic suction tube

19

SAFBAG dust bag

20

Suction hose

21

Dry ltration module with SAFBAG dust bag

22

Water lter module (ltration unit + partition)

23

Cleaning liquid container

24

Spray unit – suction hose handle attachment

25

Large atomizing nozzle

26

Small atomizing nozzle

27

Water pick up nozzle

28

Rubber slat to the large atomizing nozzle

29

Cleaning powder

30

Anti-foam agent

31

Foam lter I

32

Foam lter II

33

Inlet lter

34

Motor lter

35

HEPA outlet lter

Preparing the vacuum cleaner for operation

1

Insert the end of the suction hose to the vacuum cleaner

opening so that the markings on the hose end and on the

vacuum cleaner housing are opposite each other and turn

the hose clockwise to the position .

2

Connect the other end of the hose (handle) with the

telescopic suction tube.

3

Adjust the length of the telescopic suction tube by sliding

the slider according to the arrow and pull out/ pull the tube

together.

4

Assemble the appropriate nozzle or brush to the other

end of the suction tube.

5

Use the following nozzles and brushes for traditional

vacuum cleaning with the SAFBAG dust bag and vacuum

cleaning with the use of the water lter module: combination

brush with small item separator, small nozzle, small brush,

crevice nozzle, parquet brush or turbo brush.

6

You may assemble a basket for picking up small objects

in the combination brush with small item separator. In order

to do so remove the basket cover and insert the basket.

7

To clean hard surfaces – wooden oors, plastic oors,

ceramic tiles etc. pull out the brush by pressing the switch on

the nozzle according to the gure .

8

The vacuum cleaner is equipped with an accessory

compartment. The compartment opens/closes with the use

of a slider. To open/close the compartment side the slider

downwards/upwards and take out/ put away the desired

nozzle.

9

Close the lid.

10

Grab the plug (3) and pull the cord out of the vacuum

cleaner.

ATTENTION! While pulling out the cord pay attention

to the yellow stripe which signals the end of the

cord. Further attempts (pulling on cord) may result in

damaging the cord.

11

Plug in the appliance.

ATTENTION! Before switching on the vacuum

cleaner with the on/off button (7), make sure that the

appropriate module is installed in the container (see

section C, E, or F).

12

Switch on the vacuum cleaner by pressing the “on/off”

button (7).

In order to prepare the vacuum cleaner for wet operation

additionally:

13

Assemble the spray unit – the suction hose handle

attachment (24).

Attach the hose fastenings to the suction hose and the

●

telescopic suction tube.

14

Attach the end of the hose (sleeve) to the telescopic

suction tube and insert the other end of the hose in the small

B

A

64

atomizing nozzle or the large atomizing nozzle until you hear

a characteristic click.

15

Use the following nozzles for the wet vacuuming and wet

cleaning function or to pick up water: large atomizing nozzle,

small atomizing nozzle or the water pick up nozzle.

16

Slide the stub pipe valve plug downwards.

Insert the stub pipe of the hose to the valve in the

●

vacuum cleaner housing.

Make sure the stub pipe fastenings snap shut.

●

ATTENTION! In case of difculties in connecting the

above mentioned elements moisten the gaskets e.g.

with technical vaseline, water, etc.

Vacuum cleaner functions

TRADITIONAL CLEANING WITH SAFBAG DUST BAG

1

Press and hold the container lid opening button (2) and

lift the container lid.

2

Remove the water lter module from the container

(ltration unit and partition).

3

Insert the dry ltration module with the SAFBAG (21)

dust bag to the container.

Prepare the vacuum cleaner for operation according

●

to section B.

4

The vacuum cleaner will by default begin operation at

the medium power range. 3 diodes will light on the power

level indicator (9). Set the desired power value (this function

is only available in vacuum cleaners type 919.0) by pressing

the power adjustment buttons +/- (8).

ATTENTION! The vacuum cleaner is equipped with

a power limiting function should the inlet opening be

clogged or the SAFBAG dust bag full. It is manifested

by a pulsing limitation of the motor power and the

lighting up of the clogged air inlet indicator (11) while

the vacuum cleaner is operating at full power (type

919.0). In such a case switch off the vacuum cleaner

by pressing the on/off button (7), unplug the appliance

and clear the tubes or replace the SAFBAG dust bag.

SAFBAG dust bag disassembly/assembly

Remove the dry ltration module with the SAFBAG

●

(21)

dust bag from the container.

1

Pull the SAFBAG dust bag interlock fastening and pull

the interlock aside.

2

Pull the fastening which attaches the SAFBAG dust bag

to the basket to release the dust bag plate.

3

Remove the dust bag.

4

Insert the SAFBAG dust bag according to the arrow

printed on the bag so that the lower part of the bag plate is in

the slot of the housing. Press the upper part of the bag plate

to the fastening until you hear a characteristic click and close

the SAFBAG dust bag interlock.

Insert the dry ltration module with the SAFBAG

●

(21)

dust bag to the container.

VACUUM CLEANING WITH THE USE OF THE

WATER FILTER MODULE

1

Press and hold the container lid opening button (2) and

lift the container lid.

2

Insert the partition to the grooves in the container so that

the shutters are directed downwards. Make sure the partition

is correctly mounted in the container i.e. the partition ns

should cover the protrusion in the container.

3

Fill the container with 1,3–1,5 liter of water. The water

level should be in the range marked on the wall of the

container.

ATTENTION! Do not operate the appliance with an

empty container while vacuum cleaning with the use

of the water lter module.

4

Cover the container with the lter unit.

Prepare the vacuum cleaner for operation according

●

to section B.

The vacuum cleaner will by default begin operation at the

●

medium power range. 3 diodes will light on the power

level indicator (9). Set the desired power value (this

function is only available in vacuum cleaners type 919.0)

by pressing the power adjustment buttons +/- (8).

ATTENTION! Do not operate the appliance for too long

without replacing the water in the container.

WET VACUUMING AND WET CLEANING

Before using the wet cleaning function thoroughly vacuum

the surface to be cleaned.

Before operating the vacuum cleaner make sure the container

is empty and the water lter module and the lters are clean.

1

Press and hold the container lid opening button (2) and

lift the container lid.

2

Remove the container together with the water lter

module (lter unit and partition) from the vacuum cleaner.

3

Remove the cleaning liquid container (23) by pulling it by

the handle and lifting it upwards.

4

Open the inlet plug and ll the cleaning liquid container

(23) with the cleaning liquid (the solution of cleaning powder

and water) in the amount indicated below:

Dissolve the content of the bag in a separate container

●

in 1,5 l of warm water with the maximum temperature

of 50°C. The maximum capacity of the cleaning liquid

container is 1,7 l.

Close the inlet plug of the cleaning liquid container

●

5

Insert the cleaning liquid container (23) back to the

previous position and press the container to x it correctly

(proceed in the reverse order as in case of removing the

container).

6

Insert the container together with the water lter module

(lter unit and partition) to the vacuum cleaner.

In order to protect from the foam formation or if foam

forms during the cleaning process, use the anti-foam

C

F

E

D

65

agent recommended by ZELMER S.A. in the amount and

manner indicated on the label.

„G 478 Entschäumer D” manufactured by the company –

BUZIL, Germany.

Prepare the vacuum cleaner for operation according

●

to section B.

ATTENTION! Use only the large or small atomizing

nozzle for wet vacuum cleaning.

The vacuum cleaner will by default begin operation at the

●

medium power range. 3 diodes will light on the power

level indicator (9). Set the desired power value (this

function is only available in vacuum cleaners type 919.0)

by pressing the power adjustment buttons +/- (8).

7

Press the pump switch (6).

ATTENTION! The pump may only be switched on when

the cleaning liquid container is lled with the solution

of cleaning liquid and water. The lack of cleaning liquid

manifests in a loud operation of the pump.

If the nozzle does not atomize water although the pump is

switched on, check if the following items are correctly installed:

the cleaning liquid container (press the container), the fastening

of the stub pipe in the valve in the base of the vacuum cleaner

or the fastening of the hose end in the atomizing nozzle, check

if the atomizing nozzle is not clogged.

8

Press the button adjusting the inow of water to the

nozzle on the hose handle.

If you press the button in a pulsating manner, the water shall

temporarily ow in a slower manner to the nozzle, if you

press and slide the button backwards, the water shall be

continuously supplied to the nozzle.

The handle is also equipped with a slider to adjust the suction

power. Do not uncover this opening while picking up water or

using the wet cleaning function.

ATTENTION! Do not spray the cleaning liquid in one

place on the carpet for too long in order not to soak

the carpet.

After cleaning one part of the carpet stop the spraying

●

process and dry the carpet by sliding the nozzle back and

forth. Repeat until the whole surface of the carpet is dried.

After ending the spraying process switch off the pump

●

and press the button adjusting the water inow to the

nozzle for a moment to “release the pressure”.

ATTENTION! The vacuum cleaner is equipped with a oat

which will automatically block the suction if the foam lter

II (32) is heavily dirty or the liquid exceeds the maximum

level. It is manifested by a pulsing limitation of the motor

power and the lighting up of the clogged air inlet indicator

(11) (type 919.0). In such a case switch off the vacuum

cleaner by pressing the on/off button (7), unplug the

appliance, clean the lter and empty the container.

In case of dirt which is difcult to remove moisten the surface

with the washing agent recommended by ZELMER S.A. until

foam is formed. Leave for some time and vacuum with the

vacuum cleaner.

ATTENTION! Make sure the carpet is not soaked.

It may lead to a permanent deformation of the carpet

(folding).

PICKING UP WATER

If you want to use the vacuum cleaner to vacuum liquid in

the container, the vacuum cleaner should be prepared as in

the case of vacuum cleaning with the use of the water lter

module except that:

1. The container should be empty (without water).

2. You are to use atomizing nozzles (large or small), large

atomizing nozzle with the gathering attachment or the

nozzle for picking up water.

ATTENTION! Do not operate the vacuum cleaner with

a full container! Do not vacuum large amounts of liquid

at a time (e.g. with the hose immersed into water).

If the water exceeds the maximum level during vacuuming,

the oat will automatically block the suction. The maximum

capacity of the container is about 5 l. In such a case proceed

in the manner described above in the part concerning the

blocking of suction caused by a dirty foam lter (pulsating

motor speed).

END OF OPERATION CLEANING AND MAINTENANCE

Switch off the vacuum cleaner by pressing the on/off

●

button (7) and unplug the appliance.

Wind the cord by pressing the cord rewind button

●

(10).

While doing this hold the cord to make sure it is not

tangled and the plug does not hit the vacuum cleaner

housing.

Turn the end of the hose until the tops of the marks

●

on the end of the hose end and on the vacuum cleaner

housing are in the same position and pull the hose out

of the opening.

Remove the stub pipe of the hose by pressing the red

●

button on the valve and pull the stub pipe.

Disconnect the telescopic tube from the hose and the

●

nozzle or brush.

Pour the dirty water out of the container.

●

It is recommended to wash the container, lters

●

(disassembly below) and partition thoroughly after each

use – changing water several times.

After using the wet cleaning function thoroughly wash

●

all attachments used in this process (hose, tubes,

accessories).

ATTENTION! If you do not clean the above-mentioned

parts or clean them insufciently it may lead to the loss

of the ltration capabilities of the inserts and foam and

cause the formation of bacteria and mites.

Dry all the cleaned parts thoroughly before reassembly.

66

FILTER DISASSEMBLY

FOAM FILTER I

1

Open the lid of the lter unit by pulling the handle

upwards.

2

Take out the lter, wash it under running water, dry and

reinsert.

Close the lter unit lid by pressing it until you hear

●

a characteristic click.

FOAM FILTER II

It is recommended to wear rubber protective gloves while

dismantling the lter.

1

Grab the foam lter with your ngers and remove it from

the lter unit body.

2

Wash under running water, dry and reinsert.

ATTENTION! Do not hand wash the lter foam, do not

wring it, do not wash it in washing machines. Avoid

crumpling, stretching and deforming. After cleaning

dry the foam in room temperature. Never dry the foam

on heaters, stoves, etc.

INLET FILTER

1

Remove the SAFBAG (21) dust bag module from the

container.

2

Take out the SAFBAG dust bag from the module (see

chapter TRADITIONAL CLEANING WITH SAFBAG DUST

BAG -disassembly/assembly of the SAFBAG dust bag).

3

Release the fastening hook which xes the lid of the

SAFBAG dust bag module with the basket and pull the

basket aside.

4

Take out the lter, wash it under running water, dry and

reinsert.

Close the basket of the SAFBAG dust bag module by

●

pressing it until you hear a characteristic click.

Insert SAFBAG dust bag (see chapter TRADITIONAL

●

CLEANING WITH SAFBAG DUST BAG –disassembly/

assembly of the SAFBAG dust bag).

HEPA OUTLET FILTER AND COOLING AIR FILTER

The HEPA outlet lter should be replaced after about 30

hours of operation (6 months) or earlier in case of heavy dirt.

1

Slide the slider of the lter cover interlock downwards

and open the lter cover.

2

Remove and replace the HEPA lter with a new one

when the lter becomes dirty.

3

Remove and replace the motor lter with a new one

when the lter becomes dirty.

4

It is possible to rinse the HEPA lter and the cooling

air lter under running water. Remember to dry the above

mentioned lters before reassembly.

Close the lter cover and slide the interlock slider

●

upwards.

Ecology – environment protection

Each user can protect the natural environment. It is neither

difcult nor expensive.

In order to do it: put the cardboard packing into

recycling paper container; put the polyethylene

(PE) bags into container for plastic.

When worn out, dispose the appliance to

particular disposal centre, because of the

dangerous elements of this appliance, which

can be hazardous for natural environment.

Do not dispose into the domestic waste disposal!!!

The manufacturer does not accept any liability for any damages

resulting from unintended use or inappropriate handling. The

manufacturer reserves his rights for modifying the product any time

in order to adjust it to law regulations, norms, directives, or due to

construction, trade aesthetic or other reasons, without notifying it in

advance.

H

I

J

G

Page is loading ...

Zelmer Aquawelt 919.0 SP User manual

This manual is also suitable for

Zelmer Aquawelt 919.0 SP User manual

in other languages

Related papers

Other documents