Hyundai ACT-V-10001 User manual

SPEED CAM FULL HD

Page is loading ...

1

Thank you for purchasing the Hyundai Speed Cam. Please read these

operating instructions carefully in order to use the camcorder correctly.

Keep the instructions in a safe place after reading so that you can refer to

them later.

¾ Precautions

Before using the Speed Cam, please ensure that you read and understand

the safety precautions described below. Always ensure that the camcorder

is operated correctly.

Do not point the Speed Cam, directly into the sun or other intense light

sources which could damage your eyesight.

Do not try to open the case of the Speed Cam or attempt to modify this

Speed Cam in any way. Maintenance and repairs should be carried out

only by authorized service providers.

Keep the Speed Cam and its accessories out of the reach of children and

2

animals to prevent accidents or damage to the Speed Cam.

If you notice smoke or a strange odor coming from the Speed Cam, turn the

power off immediately. Take the Speed Cam to the nearest authorized

service center for repair. Never attempt to repair the Speed Cam on your

own.

Use only the recommended power accessories. Use of power sources not

expressly recommended for this equipment may lead to overheating,

distortion of the equipment, fire, electrical shock or other hazards.

¾ Disclaimer

We assume no responsibility for damages suffered by the user or third

parties as a result of inappropriate handling of the product or its

accessories, or by their operational failure and by their use. We reserve the

right to make changes to this product and its accessories without prior

notice.

The photos included in this user manual are only for reference.

3

Contents

¾

P

RECAUTIONS 1

¾ D

ISCLAIMER 2

P

REPARING FOR USING 5

¾

P

ART OF THE CAMCORDER 5

PREPARING BEFORE USING 6

¾

C

HARGING THE BATTERY 6

¾

B

ATTERY INDICATOR 7

¾

I

NSERTING THE MEMORY CARD 8

BASIC OPERATION 9

¾

T

URNING POWER ON AND OFF 9

¾

D

ISPLAY ON THE LCD SCREEN 10

¾

R

ECORDING MOVIE CLIPS 10

¾

S

ETTING THE RESOLUTION 11

¾

S

ETTING THE QUALITY 12

4

¾ SETTING THE TV TYPE 13

¾

S

ETTING THE DATE AND TIME 14

¾

F

ORMAT THE MEMORY CARD 16

¾ D

EFAULT SETTING 17

¾ D

OWNLOAD FILES FROM THE CAMCORDER TO PC 18

¾

P

LAYING BACK MOVIE CLIPS 19

SPECIFICATION 21

SOFTWARE INSTALLATION 22

INSTALLING THE SOFTWARE 22

5

Preparing for using

¾ Part of the camcorder

6

1:Charging LED 2: Lens

3: Menu button 4: LCD screen

5: Power button 6: REC button

7: TF card slot 8: Microphone

9: USB jack 10: HDMI jack

11. Cover

Preparing before using

¾ Charging the battery

The camcorder has a build-in lithium-ion battery, please charge the battery

at least 4 hours for first time use.

1: Push the cover locker down to open the cover, and then find the USB

jack.

2: Connect the camcorder to a PC via the USB cable.

7

3: Power off the camcorder.

4: Charging starts when charging LED turns BLUE. The charge indicator

light turns OFF when charging is completed.

5: Disconnect the camcorder. Push the cover locker down to close the

cover.

¾ Battery indicator

Battery indicator Description

The battery level is full.

The battery level is half.

The battery level is low, please prepare for

charging the battery.

8

¾ Inserting the Memory Card

You can use CF Card with this camcorder.

1:Turns off the camcorder.

2: Push the cover locker down to open the

cover, and then find the CF card slot.

3: Insert the CF card as show in the figure.

If the memory card has successfully b

e

inserted you can hear a clear buzzer and an

icon

will display on the LCD screen.

● To remove the card, gently press on the edge of the card and release it.

Pull the card out and close the cover.

● Do not touch the connection terminals on the back side of the card.

If insert or remove the card while the camcorder is power on , it may be

damages the card or data.

9

About the memory

This camcorder does not equipped with internal memory. An SD card or

multimedia card must be inserted for this spot camcorder to operate. If a

card has not been inserted this Speed Cam can not record.

Basic operation

¾ Turning Power On and Off

1:Press the POWER button to turn on the camcorder.

2: Press the POWER button again to turn the power off.

This camcorder will automatically turns off 180 seconds after the last

control accessed. Press the POWER button to turn on the camcorder.

10

¾ Display on the LCD screen

When the Speed Cam is power on, these icons will display on the LCD

screen.

¾ Recording Movie Clips

1:Turn the power on.

11

The LCD screen display .

2: Start recording.

Press the REC button to start recording. The LCD monitor displays the

recorded time.

3:Finish recording.

Press the REC button again to stop recording .The camcorder will stop

recording automatically when the memory capacity is full.

¾ Setting the resolution

1:Turn on the Speed Cam.

2: Press the MENU button, the LCD screen display

.

3: Press the REC button to enter the submenu.

4: Press the MENU button to change the resolution.

Each time the MENU button is pressed the icon on the LCD screen is

12

changed.

: The video clip size is 1440x1080.

: The video clip size is 1280x720.

: The video clip size is 848x480.

5: Press the REC button to confirm the setting. The LCD screen display

.

¾ Setting the quality

1:Turn on the Speed Cam.

2: Press the MENU button, the LCD screen display

.

13

3: Press the MENU button again , the LCD screen display

.

4: Press the REC button to enter the submenu.

5: Press the MENU button to change the quality:

:S-Fine

:Fine

: Normal

6: Press the REC button to confirm the setting. The LCD screen display

.

¾ Setting the TV type

1:Turn on the Speed Cam.

14

2: Press the MENU button, the LCD screen display .

3: Press the MENU button again until the LCD screen display.

4: Press the REC button to enter the submenu.

5: Press the MENU button to change the TV type:

NTSC:

PAL

6: Press the REC button to confirm the setting. The LCD screen display

.

¾ Setting the date and time

1:Turn on the Speed Cam.

15

2: Press the MENU button, the LCD screen display .

3: Press the MENU button again until the LCD screen display.

4: Press the REC button , the LCD screen display the year, press the REC

button again to change the value.

5: Press the MENU button again, the LCD screen display the month. Press

the REC button to change the value.

6: Press the MENU button , the LCD screen display the date, press the

REC button to change the value.

7: Press the MENU button, the LCD screen display the hour, press the

REC button to change the value.

8: Press the MENU button, the LCD screen display the minute, press the

REC button to change the value.

9: Press the MENU button until the LCD screen display

,the

setting has be saved.

16

¾ Format the memory card

1:Turn on the Speedcam.

2: Press the MENU button, the LCD screen display

.

3: Press the MENU button again until the LCD screen display

4: Press the REC button, the LCD screen display .

5: Press the MENU button the LCD screen display

6: Press the REC button, the LCD screen display .

7: Press the MENU button the LCD screen display

8: Press the REC button to format the memory, the LCD screen display

17

9: Press the REC button to close the menu. The LCD screen display

.

¾ Default setting

1:Turn on the Speed Cam.

2: Press the MENU button, the LCD screen display

.

3: Press the MENU button again until the LCD screen display

4: Press the REC button, the LCD screen display .

18

5: Press the MENU button ,the LCD screen display .

6: Press the REC button, the LCD screen display

.

7: Press the REC button again , the LCD screen display

.

¾ Download files from the camcorder to PC

There are two ways to down files from the camcorder to PC: by using the

card reader or by connecting the camcorder to a PC with the USB cable.

Using the Card Reader

1: Eject the memory card from the camcorder and insert it in a card reader

that is connected to a computer.

2: Open [My Computer] or [Windows Explorer] and double-click the

removable drive icon that represents the memory card.

19

3: Copy images from the card into a directory of your choice on the

computer’s hard disk.

Connecting the Camcorder to a PC with the USB Cable

1: Connect the camcorder with supplied USB cable to the computer's

USB port. Turn on the sort camcorder , if the connection is successful an

icon

will display on the LCD screen.

2: Open [My Computer] or [Windows Explorer]. A "Removable Disk"

appears in the drive list. Double-click the "Removable Disk" icon to view its

contents. Files stored on camcorder are located in the folder named

"DCIM".

¾ Playing back movie clips

You can only play back the movie clips by a PC or HDTV.

Page is loading ...

Hyundai ACT-V-10001 User manual

Hyundai ACT-V-10001 User manual

in other languages

Related papers

Other documents