King Canada 8040LK-BC User manual

Brand: King Canada

Model: 8040LK-BC

Type: User manual

INSTRUCTION MANUAL

MODEL: 8040LK-BC

20V MAX LITHIUM-ION

CORDLESS OSCILLATING

MULTI-TOOL KIT

WARRANTY INFORMATION

2-YEAR

LIMITED WARRANTY

FOR THIS 20V MULTI-TOOL

KING CANADA TOOLS

OFFERS A 2-YEAR LIMITED WARRANTY

FOR NON-COMMERCIAL USE.

PROOF OF PURCHASE

Please keep your dated proof of purchase for warranty and servicing purposes.

LIMITED TOOL WARRANTY

King Canada makes every effort to ensure that this product meets high quality and

durability standards. King Canada warrants to the original retail consumer a 2-year

limited warranty as of the date the product was purchased at retail and that each

product is free from defects in materials. Warranty does not apply to defects due

directly or indirectly to misuse, abuse, normal wear and tear, negligence or

accidents, repairs done by an unauthorized service center, alterations and lack of

maintenance. King Canada shall in no event be liable for death, injuries to persons

or property or for incidental, special or consequential damages arising from the use

of our products.

To take advantage of this limited warranty, return the product at your expense

together with your dated proof of purshase to an authorized King Canada service

center. Contact your retailer or visit our web site at www.kingcanada.com for an

updated listing of our authorized service centers. In cooperation with our authorized

serviced center, King Canada will either repair or replace the product if any part or

parts covered under this warranty which examination proves to be defective in

workmanship or material during the warranty period.

NOTE TO USER

This instruction manual is meant to serve as a guide only. Specifications and

references are subject to change without prior notice.

PARTS DIAGRAM & PARTS LISTS

Refer to the Parts section of the King Canada web site for the most updated parts

diagram and parts list.

KING CANADA INC. DORVAL, QUÉBEC, CANADA H9P 2Y4

www.kingcanada.com

1. KNOW YOUR TOOL

Read and understand the instruction manual and labels affixed to the tool. Learn its

application and limitations as well as its specific potential hazards.

2. Don’t use power tools in damp or wet locations or expose them to rain. Keep work area

well lit and provide adequate surrounding work space.

3. USE RIGHT TOOL.

Don’t force the tool or the attachment to do a job for which it was not designed.

4. WEAR PROPER APPAREL.

Do not wear loose clothing, gloves, neckties or jewelry (rings, watch) because they could

get caught in moving parts. Non-slip footwear is recommended. Wear protective hair

covering to contain long hair. Roll up long sleeves above the elbows.

5. MAINTAIN TOOL WITH CARE.

Keep tool clean for best and safest performance. Follow instructions for operation and

changing accessories.

6. DISCONNECT TOOLS.

Before servicing, when changing accessories or attachments.

7. AVOID ACCIDENTAL STARTING.

Make sure the switch is in the ‘’OFF’’ position before connecting battery.

8. USE RECOMMENDED ACCESSORIES.

Consult the manual for recommended accessories. Follow the instructions that

accompany the accessories. The use of improper accessories may cause hazards.

9. CHECK FOR DAMAGED PARTS.

Before further use of the tool, a guard or other parts that are damaged should be

carefully checked to ensure they will operate properly and perform their intended

function. Check for alignment of moving parts, breakage of parts, mounting, and any

other conditions that may affect its operation. A guard or other parts which are damaged

should be properly repaired or replaced.

Specific Safety Instructions

1. Only use King attachments and accessories, serious injury can result if this warning is

not respected.

2. Before installing or changing an accessory, remove the battery from the tool.

3. Hold power tool by insulated grip surface, an accessory could contact hidden wiring,

contact with a “live” wire will make exposed metal surfaces “live” and will shock the

operator.

4. Avoid body contact with earthed or grounded surfaces such as pipes, radiators,

stoves and refrigerators. Risk of electric shock if your body is grounded.

5. Use clamps or any other practical way to secure and support the workpiece to a stable

platform. Holding the work by hand or against your body is unstable and may lead to

loss of control.

6. Wear protective gloves and safety glasses, an accessory can become extremely hot

during operation, danger of burns!

7. Do not use the tool if switch does not turn it on or off. Any tool that cannot be controlled

with the switch is dangerous and must be repaired.

GENERAL & SPECIFIC

SAFETY INSTRUCTIONS

LITHIUM-ION BATTERY &

CHARGER INFORMATION

WARNING: The warnings, cautions, and instructions discussed in this instruction manual

cannot cover all possible conditions and situations that may occur. It must be understood

by the operator that common sense and caution are factors which cannot be built into this

product, but must be supplied by the operator. Do not plug in charger or install battery into

Multi-tool until you have read and understood this instruction manual.

King canada offers a variety of 20V max Lithium-ion Power Tools which can all use the

same battery and battery charger.

Available batteries and charger for this 20V max Li-ion Multi-tool Kit:

• 1.5 Ah 20V max Lithium-ion battery (Model K-020LBT)

• 3.0 Ah 20V max Lithium-ion battery (Model K-023LBT-3)

• 20V max Lithium-ion battery charger (Model K-020LCG)

Charging any other battery may damage the charger and possibly cause serious injury.

Battery and Charger Safety Precautions

1) Do not store or carry battery in a way which metal objects could contact the exposed

metal end of the battery. The battery could short-circuit causing a fire, personal injury

and damage to the battery.

2) Never attempt to open the battery for any reason. If battery housing has cracked,

discontinue use immediately and do not try to recharge it. Dispose of battery.

3) Never charge a wet battery or a battery that shows signs of corrosion.

4) Do not use an extension cord with the charger, plug charger directly into a 120V AC

receptacle.

5) Do not use charger if power cord is damaged, replace damaged cord or charger.

6) Do not charge battery when work area or the battery temperature is or below 0

C or

above 45

7) Unplug charger when not in use.

8) It is important to recycle or dispose of battery properly at your nearest battery

recycling location.

9) The contents of the battery is slightly acidic, do not incinerate the battery, it can

explode in a fire.

10) A small leakage from the battery may occur under extreme usage, charging or

temperature conditions. This does not indicate a battery failure. However, if the battery

housing is cracked and leakage gets on your skin, follow these steps;

-Wash with soap immediately.

-Neutralize area with mild acid such as vinegar or lemon juice.

-If leakage gets into your eyes, flush with clean water for a minimum of 10 minutes, then

seek medical attention.

Lithium-ion Battery

Lithium-ion batteries do not have a memory and do not require to be completely

discharged periodically. After use, charge battery so that it is fully charged for the next time

you use this tool. A fully charged battery will only loose about 2% of its charge per month

during storage.

GETTING TO KNOW YOUR TOOL

SPECIFICATIONS

Model................................................................................................................8040LK-BC

Voltage ................................................................................................................20V MAX

Variable speed (oscillations per minute)......................................................5,000 - 16,000

Weight ......................................................................................................................2.5 lbs

Battery types ..................................1.5Ah (Mod. K-020LBT) or 3.0Ah (Mod. K-023LBT-3)

Battery charger ........................................................................................Mod. K-020LCG

Figure 1

1. 6 pin mounting plate

2. Accessory locking pin

3. Quick release

4. On/Off switch

5. Battery compartment

6. Variable speed dial

7. Woodcutting blade

8. Sanding papers

9. Scraper blade

10. Sanding pad

11. Battery charger

12. Battery

13. Carry bag

Unpacking your Multi-tool Kit

Your cordless Multi-tool requires minimal assembly before use, remove all contents from

the box. Inspect the tool carefully to make sure no breakage or damage has occurred

during transport. If any parts are missing, do not attempt to use the tool until you have

obtained the missing parts from your King Canada retailer.

Contents:

1- Cordless Multi-tool

1- Battery

1- Battery Charger

1- Sanding back-up pad

3- Sanding papers (80, 120 and 180 Grit)

1- Scraper blade

1- Woodcutting blade

OPERATION

USING YOUR 20V MAX LITHIUM-ION CORDLESS

OSCILLATING MULTI-TOOL

WARNING: Do not install battery until the accessory is

installed securely to the tool. Wear protective gloves

and safety glasses, an accessory can become extremely

hot during operation, danger of burns!

Charging the battery/battery level indicator

20V max Li-ion batteries come with a battery power level

indicator (A) Fig.2, press the button (B) to see the charge

level. If the battery level is low charge the battery. To

charge the battery (C) Fig.2, plug charger (D) power cord

into a 120V AC receptacle (do not use extension cord).

The green LED (E) will flash to indicate power to the

charger. Align the grooves the battery with those of the

charger and slide the battery all the way until it snaps into

place. The red LED (F) will light up indicating the

charging procedure has begun. Once the green LED (E)

lights up, the battery is fully charged and ready to use.

Press the battery clip (B) Fig.3 to remove battery from

charger.

Installing/removing battery from drill

To install a battery (A) Fig.3 to the base of the tool, align

the grooves of the battery with those of the base and

slide the battery all the way until the battery clip (B) snaps

and holds the battery into place.

To remove the battery from the base, press the battery

clip (B) Fig.3 and slide the battery away from the base.

Turning Tool On/Off

To turn your Multi-tool ON, push the switch (A) Fig.4

towards the front of the tool. Push the switch towards the

rear of the tool to turn your Multi-tool OFF.

Figure 2

Figure 3

Figure 4

OPERATION

ASSEMBLY & OPERATION

Installing Accessories to Multi-tool

• DISCONNECT BATTERY FROM TOOL BASE.

This kit comes with 3 different accessory attachments, Rigid Offset Scraper Blade, Sanding

Pad with hook & loop backing (and 3 sanding papers, 80, 120 & 180 grit) and a Offset

Woodcutting Saw Blade. Only one accessory at a time can be installed to the multi-tool.

To secure an accessory to the multi-tool;

1) Lift and pivot the quick release latch (A) Fig.5 foward 180 degrees as shown to release

the accessory and/or the accessory

locking pin (B).

2) Select the required accessory for the

desired job. Align the mounting holes (C)

Fig.5 on the accessory over the 6 pins of

the mounting plate (D).

3) Slide the accessory locking pin (B) Fig.5

through the accessory and into the tool

and hold it there.

4) Pivot the quick release latch (A) Fig.5

backwards 180 degrees to lock the

accessory.

Variable Speed Selector Dial

This tool comes with a variable speed

selector dial, to increase speed, turn selector dial (A)

Fig.6 towards the left, to decrease speed, turn selector

dial towards the right.

Securing Workpiece

Use clamps or any other practical way to secure and

support the workpiece to a stable platform. Holding the

work by hand or against your body is unstable and may

lead to loss of control and injury.

ACCESSORIES

Woodcutting Saw Blade- Saws wood, plaster board

and soft plastics. Plunges easily into any point in the

material.

Sanding Back-up Pad- Multi-tool sands effortlessly and precisely in corners and edges.

Tips: Only dry sand wood or metal. When only one tip of the sanding paper is worn, the

sanding paper can be pulled off, turned and reinstalled to use a unused corner.

Rigid Scraper Blade- Removes lacquer, carpeting, tile adhesives and underseal coatings.

Figure 5

Figure 6

ACCESSORIES & MAINTENANCE

OPTIONAL ACCESSORIES AVAILABLE

Other Multi-tool accessories are available, refer to the list below. Contact your nearest King

Canada distributor for more information and availability.

MAINTENANCE

WARNING: THERE ARE NO USER SERVICE-ABLE PARTS INSIDE

Preventative maintance performed by an unauthorized personnel may result in the

misplacement of internal wires and componenets which could cause serious hazards. We

recommend that all servicing be performed by a qualified KING CANADA service centre

technician.

Battery

Pay attention to the battery power levels as the battery nears its end of life. If you notice a

decrease in battery performance or a significant difference in running power between

charges, then it is time to replace the battery. Failure to do so may damage the charger

and cause improper operation.

Cleaning

To avoid accidents, always remove the battery from the tool before cleaning. The tool is

most effectively cleaned with the use of an air compressor. Always wear safety glasses

when using an air compressor. Ventilation openings and switch levers must be kept clean

and free of foreign objects. Do not insert pointed objects through these openings in the

attempt to clean them.

1. Air vents of the tool should be cleaned regularly to avoid overheating of the motor which

is caused by the blocking of the air vents.

2. DON’T clean this tool with water, as no liquid is allowed in the tool body. Clean the tool

with a dry clean cloth only. Compressed air at low pressure is also suitable.

3. DON’T allow petroleum based products to come into contact with the plastic parts of the

tool, as they contain chemicals that can damage or destroy the plastic parts.

KW-4801- HSS Segment Saw Blade (1pc)

KW-4802- HSS Segment Saw Blade (1pc)

KW-4803- Carbide Abrasive Saw Blade (1pc)

KW-4804- Triangular Carbide Rasp (1pc)

KW-4805- Tru-cut Saw Blades Kit (3pcs)

(10, 20 & 35mm)

KW-4806- Continuous Rim Diamond Cutter (1pc)

KW-4808- Adaptor (1pc)

KW-4810- Sanding Paper Kit (15pc, 60 grit)

KW-4811- Sanding Paper Kit (15pc, 80 grit)

KW-4812- Sanding Paper Kit (15pc, 120 grit)

KW-4813- Sanding back-up pad (1pc)

KW-4815- Scraping Blade Kit (2pcs)

KW-4816- Pointed Scraping Blade (1pc)

KW-4817- Tru-cut Wood Blade (1pc, 20mm)

KW-4818- Tru-cut Bi-metal Blade (1pc, 20mm)

KW-4819- Tru-cut Wood Blade (1pc, 35mm)

KW-4820- Tru-cut Bi-metal Blade (1pc, 35mm)

KW-4821- Tru-cut Bi-metal Flush (1pc, 68mm)

King Canada 8040LK-BC User manual

King Canada 8040LK-BC User manual

King Canada 8040LK-BC User manual

Related papers

Other documents