2. Miller
  3. PIPEWORX FEEDER CART
PIPEWORX FEEDER CART

Miller PIPEWORX FEEDER CART, LJ000000 Owner's manual

  • Hello! I am an AI chatbot trained to assist you with the Miller PIPEWORX FEEDER CART Owner's manual. I’ve already reviewed the document and can help you find the information you need or explain it in simple terms. Just ask your questions, and providing more details will help me assist you more effectively!
OWNER’S MANUAL
© 2008 MILLER Electric Mfg. Co.
OM-240 710A 2008−09
PipeWorx Feeder Cart
1. Safety Symbol Definitions
Warning! Watch Out! There are possible hazards as
shown in the adjoining symbols.
Trailers /Running Gear
Falling equipment can cause serious personal injury and
equipment damage. Use lifting eye to lift unit only, not
trailer, gas cylinders, or any other accessories. Use
equipment of adequate capacity to lift unit or parts such
as engine or generator.
Falling equipment can cause injury and damage, over-
sized cylinder can cause tipping. Properly install and se-
cure all equipment onto cart before using cart. Always
secure or remove any tools stored on cart before moving
unit. Do not lift cart in any manner when equipment and/or
cylinder(s) are installed − use handles to move cart. Do
not overload handles with cables − use standard 10 to 15
foot cables as maximum lengths.
Beware of electric shock from wiring. Disconnect input
power before moving cart.
Tipping equipment can cause injury and damage
equipment. Do not move cart where two wheels are at
different heights and cart could tip − avoid tipping. Be
careful when moving unit over uneven surfaces.
Wear safety glasses with side shields.
2. Cart Package
805 370-A
1 Cart Package
Cart is packaged on a skid.
Illustration is shown with carton
cover removed.
1
OM-240 710 Page 2
3. Unpackage Parts
805 371-A
1 Carton
Carton contains 2 wheels, 1 angle
bracket, 1 cable hanger bracket, and a
hardware bag.
2 Axle
3 Vertical Support (4)
4 Handle Assembly
Remove 2 screws that hold handle
assembly to top shelf.
5 Top Shelf
6 Bottom Shelf
Remove 4 lag bolts that hold bottom shelf
to skid.
Tools Needed:
1/2 in
3/8 in
1
2
3
3
4
5
6
OM-240 710 Page 3
4. Installing Axle And Wheels
804 934-B
1 Bottom Shelf
2 Axle
3 Flat Washer
4 Retaining Ring
Install axle in bottom shelf.
Place a supplied flat washer, wheel
and a second flat washer on axle
as shown. Secure wheel to axle
with supplied retaining ring.
Install the remaining wheel using the
same procedure as the first wheel.
Tools Needed:
1
2
3
4
. Use a knife to
clean paint from
retaining ring
groove in axle.
OM-240 710 Page 4
5. Installing Vertical Supports
805 373-A
1 Bottom Shelf
2 Vertical Support
Install vertical supports to bottom
shelf using the supplied 10-32
screws.
2
1
Tools Needed:
5/16 in
OM-240 710 Page 5
6. Installing Top Shelf
805 374-A
1 Top Shelf
2 Vertical Support
Install top shelf to vertical
supports using the supplied 10-32
screws.
1
2
Tools Needed:
5/16 in
. Do not install the 2 top
screws until handle
assembly is installed
to top shelf.
OM-240 710 Page 6
7. Installing Handle Assembly, Angle Bracket, And Cable Hanger
805 375-A / 805 376-A
1 Top Shelf
2 Handle Assembly
3 Angle Bracket
4 Cable Hanger
Install handle assembly to top
shelf using the supplied 10-32
screws.
Install angle bracket to top shelf
using the supplied 10-32 screws.
Install cable hanger to top shelf
using the supplied 10-32 screws.
4
1
Tools Needed:
5/16 in
2
3
Completed Feeder Cart Assembly
OM-240 710 Page 7
8. Parts List
805 318-A
. Hardware is common and
not available unless listed.
8
1
2
3
4
5
6
7
9
10
13
11
12
14
15
6
13
Figure 1. Parts Assembly
OM-240 710 Page 8
Description
Part
No.
300 467 Cart, PipeWorx Feeder
Quantity
1 217255 SLIDE,DRAWER 2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2 234505 HANDLE ASSY, FEEDER CART 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3 234546 TAB,LIFT SLOT 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4 234554 SHELF,UPPER,FEEDER CART 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5 235121 BRACKET,CABLE HOLDER 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
6 234555 LEG,FRONT RIGHT 2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
7 234553 AXLE,CART 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
8 163463 WHEEL,RBR TIRE 10.000 OD X 2.000 WIDE X .750 BORE 2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
9 602250 WASHER,FLAT .812ID X 1.469OD X .134T STL PLD 4. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
10 121614 RING,RTNG EXT .750 SHAFT X .085 THK E STYLE PLD 2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
11 234545 SHELF,LOWER,FEEDER CART 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
12 123557 CASTER,SWVL 5.00 IN POLYOLEFIN X 1.375 X .437−14 2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
13 234556 LEG,FRONT LEFT 2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
14 237215 BRACKET,DRAWER 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
15 232470 DRAWER,ASSY 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
To maintain the factory original performance of your equipment, use only Manufacturer’s Suggested
Replacement Parts. Model and serial number required when ordering parts from your local distributor.
/