Miller LJ000000 Owner's manual

Brand: Miller

Model: LJ000000

Type: Owner's manual

This manual is also suitable for

PIPEWORX FEEDER CART

OWNER’S MANUAL

OM-240 710A 2008−09

PipeWorx Feeder Cart

1. Safety Symbol Definitions

Warning! Watch Out! There are possible hazards as

shown in the adjoining symbols.

Trailers /Running Gear

Falling equipment can cause serious personal injury and

equipment damage. Use lifting eye to lift unit only, not

trailer, gas cylinders, or any other accessories. Use

equipment of adequate capacity to lift unit or parts such

as engine or generator.

Falling equipment can cause injury and damage, over-

sized cylinder can cause tipping. Properly install and se-

cure all equipment onto cart before using cart. Always

secure or remove any tools stored on cart before moving

unit. Do not lift cart in any manner when equipment and/or

cylinder(s) are installed − use handles to move cart. Do

not overload handles with cables − use standard 10 to 15

foot cables as maximum lengths.

Beware of electric shock from wiring. Disconnect input

power before moving cart.

Tipping equipment can cause injury and damage

equipment. Do not move cart where two wheels are at

different heights and cart could tip − avoid tipping. Be

careful when moving unit over uneven surfaces.

Wear safety glasses with side shields.

2. Cart Package

805 370-A

1 Cart Package

Cart is packaged on a skid.

Illustration is shown with carton

cover removed.

OM-240 710 Page 2

3. Unpackage Parts

805 371-A

1 Carton

Carton contains 2 wheels, 1 angle

bracket, 1 cable hanger bracket, and a

hardware bag.

2 Axle

3 Vertical Support (4)

4 Handle Assembly

Remove 2 screws that hold handle

assembly to top shelf.

5 Top Shelf

6 Bottom Shelf

Remove 4 lag bolts that hold bottom shelf

to skid.

Tools Needed:

1/2 in

3/8 in

OM-240 710 Page 3

4. Installing Axle And Wheels

804 934-B

1 Bottom Shelf

2 Axle

3 Flat Washer

4 Retaining Ring

Install axle in bottom shelf.

Place a supplied flat washer, wheel

and a second flat washer on axle

as shown. Secure wheel to axle

with supplied retaining ring.

Install the remaining wheel using the

same procedure as the first wheel.

Tools Needed:

. Use a knife to

clean paint from

retaining ring

groove in axle.

OM-240 710 Page 4

5. Installing Vertical Supports

805 373-A

1 Bottom Shelf

2 Vertical Support

Install vertical supports to bottom

shelf using the supplied 10-32

screws.

Tools Needed:

5/16 in

OM-240 710 Page 5

6. Installing Top Shelf

805 374-A

1 Top Shelf

2 Vertical Support

Install top shelf to vertical

supports using the supplied 10-32

screws.

Tools Needed:

5/16 in

. Do not install the 2 top

screws until handle

assembly is installed

to top shelf.

OM-240 710 Page 6

7. Installing Handle Assembly, Angle Bracket, And Cable Hanger

805 375-A / 805 376-A

1 Top Shelf

2 Handle Assembly

3 Angle Bracket

4 Cable Hanger

Install handle assembly to top

shelf using the supplied 10-32

screws.

Install angle bracket to top shelf

using the supplied 10-32 screws.

Install cable hanger to top shelf

using the supplied 10-32 screws.

Tools Needed:

5/16 in

Completed Feeder Cart Assembly

OM-240 710 Page 7

8. Parts List

805 318-A

. Hardware is common and

not available unless listed.

Figure 1. Parts Assembly

OM-240 710 Page 8

Description

Part

No.

300 467 Cart, PipeWorx Feeder

Quantity

1 217255 SLIDE,DRAWER 2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

2 234505 HANDLE ASSY, FEEDER CART 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

3 234546 TAB,LIFT SLOT 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

4 234554 SHELF,UPPER,FEEDER CART 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

5 235121 BRACKET,CABLE HOLDER 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

6 234555 LEG,FRONT RIGHT 2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

7 234553 AXLE,CART 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

8 163463 WHEEL,RBR TIRE 10.000 OD X 2.000 WIDE X .750 BORE 2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

9 602250 WASHER,FLAT .812ID X 1.469OD X .134T STL PLD 4. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

10 121614 RING,RTNG EXT .750 SHAFT X .085 THK E STYLE PLD 2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

11 234545 SHELF,LOWER,FEEDER CART 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

12 123557 CASTER,SWVL 5.00 IN POLYOLEFIN X 1.375 X .437−14 2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

13 234556 LEG,FRONT LEFT 2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

14 237215 BRACKET,DRAWER 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

15 232470 DRAWER,ASSY 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

To maintain the factory original performance of your equipment, use only Manufacturer’s Suggested

Replacement Parts. Model and serial number required when ordering parts from your local distributor.