Roland AT-800 Owner's manual

Type
Owner's manual

This manual is also suitable for

* 5 1 0 0 0 3 1 9 6 6 - 0 1 *
Errata
Using Rhythm Performance
Selecting a Rhythm
Rhythm Search
Searching by Conditions
Add an operation between steps 5 and 6
6. Touch <EXIT>.
(Renumber the subsequent steps)
Using Rhythm Performance
A Simple Way to Make Automatic Accompaniment Settings
Correct the explanation and add a note
< Incorrect > < Correct >
[Sync Start] button lit, [Intro]
button blinking (Waiting for Sync
Start)
[Sync Start] button lit, [Intro]
button lit (Waiting for Sync Start)
< Add >
Note
The group name will depend on the model you’re using.
Using the Registration Buttons
Loading Previously Saved Registration Sets Into the ATELIER
Recalling the Order that the Registrations are Saved
Correct the procedure in step 2
2. Load the  rst registration.
For details, refer to “Loading a Set of Registrations.
3. Press the [Load Next] button.
The following registration set will be loaded into the instrument.
(Renumber the subsequent steps)
Recording/Playing Back What You Play
Viewing a Notation
Add a memo to step 6
MEMO
If you’re using the Upgrade/Expansion Package, touch <Part> to
change the part thats displayed.
Recording/Playing Back What You Play
Starting Recording at the Right Moment
Add an explanation to step 5
If the setting is “OFF, no count will be heard before recording;
recording will begin immediately.
Appendices
Setting That Are Stored After the Power Is Turned O
Correct the item "Settings That Are Stored at the Individual
Registration Buttons"
Delete “[Ending] button (ON/OFF)”
(Not stored in memory.)
Please make the following corrections to the AT900 AT900C owner’s manual, and the AT800 owner's manual, the Upgrade/Expansion Package owner’s
manual.
AT900, AT900C, AT800, ATUP-EX
Copyright © 2012 ROLAND CORPORATION All rights reserved.
No part of this publication may be reproduced in any form without the written
permission of ROLAND CORPORATION.
If youre using the Upgrade/Expansion Package
When you perform the following procedure, your selection will
be con rmed as soon as you select it, without the indicator of
the button blinking. There is no need to con rm your selection
by pressing the button once again.
Selecting and Playing Sounds
Selecting Voices
Selecting a Voice Using the [Others] Button
Steps 4, 5, 6
Selecting and Playing Sounds
Playing Drum Sounds or Sound E ects from the Entire Lower Keyboard
Changing Drums/SFX Sets
Steps 2, 3
Selecting and Playing Sounds
Playing a Lower Voice with Percussion Instrument Sounds and a Voice Phrase
Changing the Manual Percussion Sets
Steps 2, 3
Using Rhythm Performance
Selecting a Rhythm
Steps 2, 3
Using Rhythm Performance
Selecting a Rhythm
Using Rhythm Stored in User Memory
Steps 3, 4
Applying Various E ects to the Sound
Adding Harmony to a Melody
Changing the Harmony Intelligence Type
Steps 2, 3
Updating (Upgrade/Expansion Package owner's manual P.6)
Add the following memos to step 3
* After you’ve pressed the [Power On] switch, it will take
approximately 10 seconds for the screen to appear.
* The message “Now Data Testing... will continue to be shown in
the display for approximately 10 minutes.
Recording and Playback
(Upgrade/Expansion Package owner’s manual P.41)
< Incorrect > < Correct >
q =10–500 q =20–500
Notation (Upgrade/Expansion Package owners manual P.43)
Correct the procedure in step 6
< Incorrect > < Correct >
After you’ve read the message,
touch <OK>.
After you’ve read the message,
touch <Close>.
  • Page 1 1
  • Page 2 2

Roland AT-800 Owner's manual

Type
Owner's manual
This manual is also suitable for

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

in other languages