Skil LL9322G-01 Owner's manual

Page is loading ...

2

TABLE OF CONTENTS

General Laser Tool Safety Warnings. ...............................3

FCC Statement ................................................ 3-4

Safety Rules For Connecting External Power Supply ..................4

Symbols .....................................................5-6

Get to Know Your Laser Tool. ......................................7

Packing List ....................................................8

Specications ..................................................8

Operating Instructions ........................................9-14

Maintenance ...................................................15

Trouble Shooting ...............................................15

Limited Warranty Of Skil Consumer Tools ..........................16

3

GENERAL LASER TOOL SAFETY WARNINGS

READ ALL INSTRUCTIONS BEFORE USING THE TOOL!

WARNING

LASER RADIATION.

Do not stare into beam. Class II laser product. Turn

the laser beam on only when using this tool.

Do not remove or deface any product labels.

Avoid direct eye exposure. The laser beam can

cause ash blindness.

Do not operate the tool around children or allow

children to operate the tool.

Do not place the tool in a position that may cause

anyone to stare at the laser beam, whether

intentionally or unintentionally.

Do not use on surfaces such as sheet steel that

have shiny, reective surfaces. The shiny surface

could reect the beam back at the operator.

Always turn the laser tool off when not in use.

Leaving the tool on increases the risk of someone

inadvertently staring into the laser beam.

Do not attempt to modify the performance of

this laser device in any way. This may result in a

dangerous exposure to laser radiation.

Do not attempt to repair or disassemble the tool. If unqualied persons attempt to repair

this product, serious injury may occur. Any repair required on this laser product should be

performed only by qualied service personnel.

Use of other accessories that have been designed for use with other laser tools could result in

serious injury.

Do not operate the tool outdoors.

Do not place or store tool under extreme temperature conditions.

FCC STATEMENT

The manufacturer is not responsible for radio interference caused by unauthorized

modications to this equipment. Such modications could void the user’s authority to operate

the equipment.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two

conditions:

(1) This device may not cause harmful interference.

(2) This device must accept any interference received, including interference that may cause

undesired operation.

Changes or modications not expressly approved by the party responsible for compliance

could void the user’s authority to operate the equipment.

CAN ICES-3(B)/NMB-3(B)

MADE IN CHINA /

HECHO EN CHINA /

FABRIQUÉ EN CHINE

SERIAL NO. / SERIE NO. /

NUMÉRO DE SÉRIE

Model / Modelo / Modèle: LL9322G-00

7.40 Wh

PRODUCTO LÁSER CON SALIDA < 1mW. CLASE II, 520nm, 3,7V , 2000mAh

polímero de litio

CUMPLE CON LAS SECCIONES 21 CFR 1040.10 Y 1040.11

520nm, SORTIE < 1 mW/PRODUIT LASER DE CLASSE II Pile au lithium-polymère de

3,7 V , 2000 mAh

CONFORME AUX NORMES 21CFR ARTICLES 1040.10 ET 1040.11

CAUTION: Risk of re and burns. Do not open, crush, heat above 100° C (212° F) or

incinerate.

PRECAUCIÓN : Riesgo de incendio y quemaduras. No abra, triture, permita que esté

a mayor temperatura que 100° C (212 °F) ni incinere.

ATTENTION : Risque d’incendie et de brûlures. N’ouvrez pas le produit, ne l’écrasez

pas, ne le chauffez pas à plus de 100 ºC (212°F) et ne l’incinérez pas.

CAUTION/PRECAUCIÓN/ATTENTION

AVOID EXPOSURE/EVITE LA EXPOSICIÓN/ÉVITEZ L’EXPOSITION

LASER RADIATION IS EMITTED FROM THIS APERTURE

LA RADIACIÓN LÁSER SE EMITE DE ESTA ABERTURA

CET OUTIL PRODUIT UN RAYONNEMENT LASER

LASER RADIATION-DO NOT STARE INTO BEAM

RADIACIÓN LÁSER: NO MIRE DIRECTAMENTE EL RAYO

RAYONNEMENT LASER – NE FIXEZ PAS DES YEUX LE RAYON LASER

520nm, OUTPUT < 1mW/CLASS II LASER PRODUCT 3.7V , 2000mAh Li-Polymer

COMPLIES WITH 21 CFR PARTS 1040.10 AND 1040.11

4

NOTE!

This equipment has been tested and found to comply with the limits for a Class B

digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide

reasonable protection against harmful interference in a residential installation. This equipment

generates, uses, and can radiate radio frequency energy and, if not installed and used in

accordance with the instructions, may cause harmful interference to radio communications.

However, there is no guarantee that interference will not occur in a particular installation. If

this equipment does cause harmful interference to radio or television reception, which can be

determined by turning the equipment off and on, the user is encouraged to try to correct the

interference by one or more of the following measures:

•

Reorient or relocate the receiving antenna.

•

Increase the separation between the equipment and receiver.

•

Connect the equipment into an outlet on a circuit different from that to which the receiver is

connected.

•

Consult the dealer or an experienced radio/TV technician for help.

DANGER

People with electronic devices, such as pacemakers, should consult their

physician(s) before using this product. Operation of electrical equipment in

close proximity to a heart pacemaker could cause interference or failure of the pacemaker.

SAFETY RULES FOR CONNECTING EXTERNAL POWER

SUPPLY

WARNING

Read and follow all instructions below before connecting with an

external power supply, such as AC supply or DC mobile power.

Failure to follow all instructions below may result in electric shock, explosion, re and/or

serious personal injury.

Use only an adapter for which output voltage is 5V and output electricity is ≥0.5A.

Conrm that the adapter suits the AC supply before connecting.

Conrm that the mobile power source has output voltage of 5V and output electricity of ≥0.5A

before connecting.

Keep the adapter clean. Check the adapter, cable and plug before do connecting. If damage is

detected, do not use or repair by yourself, change the damaged one or get repairs performed

by authorized service personnel, otherwise electric shock may occur.

Do not connect with AC supply on easily ammable surfaces (e.g., paper, textiles, etc.) or

surroundings. The heating of the adapter during use may pose a re hazard.

Children or persons with physical, sensory or mental limitations or lack of experience and

knowledge are not capable of securely operating the adapter unless they are being given

supervision or have been instructed by a responsible person.

5

SYMBOLS

Safety Symbols

The purpose of safety symbols is to attract your attention to possible dangers. The safety

symbols and the explanations with them deserve your careful attention and understanding.

The symbol warnings do not, by themselves, eliminate any danger. The instructions and

warnings they give are no substitutes for proper accident prevention measures.

WARNING

Be sure to read and understand all safety instructions in this Operator’s

Manual, including all safety alert symbols such as “

DANGER

,”

“

WARNING

,” and “

CAUTION

” before using this tool. Failure to following all instructions listed

below may result in electric shock, re, and/or serious personal injury.

The denitions below describe the level of severity for each signal word. Please read the

manual and pay attention to these symbols.

This is the safety alert symbol. It is used to alert you to potential

personal injury hazards. Obey all safety messages that follow this

symbol to avoid possible injury or death.

DANGER

DANGER indicates a hazardous situation which, if not avoided, will

result in death or serious injury.

WARNING

WARNING indicates a hazardous situation which, if not avoided, could

result in death or serious injury.

CAUTION

CAUTION, used with the safety alert symbol, indicates a hazardous

situation which, if not avoided, will result in minor or moderate injury.

Damage Prevention And Information Messages

These inform the user of important information and/or instructions that could lead to equipment

or other property damage if they are not followed. Each message is preceded by the word

“NOTICE”, as in the example below:

NOTICE:

Equipment and/or property damage may result if these instructions are not followed.

IMPORTANT:

Some of the following symbols may be used on your tool. Please study them

and learn their meaning. Proper interpretation of these symbols will allow you to operate the

tool better and safer.

Symbol Name Designation/Explanation

V Volts Voltage (potential)

A Amperes Current

mW Milliwatt Power

nm Nanometer Wavelength

kg Kilograms Weight

min Minutes Time

6

Symbol Name Designation/Explanation

s Seconds Time

Wh Watt-hours Battery capacity

mAh Milliampere-Hours Battery capacity

Direct current Type or a characteristic of current

Unlock Icon

Push the mode switch in the direction

of the icon, the tool will enter the self-

leveling mode and the cross line laser will

be turned on

Lock Icon

Push the mode switch in the direction of

the icon, the tool will be turned off and

locked

LED Indicator for Leveling

Status

If the tool is placed exceeds the self-

leveling range (±4°from horizontal) in self-

leveling mode, or when the tool is working

in manual leveling mode, it will illuminate

in red

LED Indicator for Battery

Capacity

The color status varies with the battery

capacity the tool rests during charging

and normal usage

Laser Button

To turn the Self-Leveling 360 Degree

Cross Line Laser on and off in manual

leveling mode; Switch laser projection

mode in both self-leveling and manual

leveling modes

CEC Energy Efciency Logo

CEC certication logo for battery charging

system

Li-ion RBRC seal

Designates Li-ion battery recycling

program

Read manual symbol Alerts user to read manual

7

GET TO KNOW YOUR LASER TOOL

This Self-Leveling 360 Degree Cross Line Laser is highly versatile. It can be hand-held,

leveled on a horizontal surface or mounted on a tripod (included).

Laser Aperture

Mode Switch

Unlock Icon

Lock Icon

Micro-USB Charging Port

Laser

Button

LED Indicator for

Leveling Status

LED Indicator for

Battery Capacity

1/4’’ Threaded

Mounting Hole

Handle

Center

Column

1/4’’ Screw

Locking

Knob2

USB

Charging

Cable

Adjustable

Foot

Mounting

Plate

Locking

Knob3

1/4’’ Screw

Platform

Flip Lever

Crank

Locking

Knob1

Fig. 1

8

PACKING LIST

PART NAME QTY

Self-leveling 360 Degree Green Cross line Laser 1

Tripod 1

USB Charging Cable 1

Soft Bag 1

Instruction Manual 1

SPECIFICATIONS

Battery voltage 2000mAh 3.7V Lithium

Laser λ=520nm; Class II laser, Maximum laser output < 1mw

Self-levelling range ± 4°

Accuracy ±3/16 inch at 30 feet (0.5mm/m)

Operating range (typically,

depending on room illumination )*

100 feet (30m)

Operating time Approximately 6 hours

Optimum operating temperature +23°F to 104°F (-5℃ to 40℃)

Storage temperature -4°F to 158°F (-20℃ to 70℃)

*Important: Under unfavorable conditions, such as in bright light, the tool’s operating range

will be reduced.

9

OPERATING INSTRUCTIONS

WARNING

To reduce the risk of re, personal injury, and product damage due to

a short circuit, never immerse your tool or charger in uid or allow a

uid to ow inside them.

Corrosive or conductive uids, such as seawater, certain industrial

chemicals, and bleach or bleach containing products, etc., can cause a short circuit.

Applications

Your Self-Leveling 360 Degree Cross Line Laser can be hand-held for point marking and

simple alignment by sight, or it can be used to make a “chalk line” when in the lock mode. It

also can be mounted on a standard 1/4” tripod (included) to project laser lines on walls. It is

ideal for the following applications:

•

Hanging pictures, photos, or artwork on walls

•

Wallpapering and stencil work

•

Framing doors and windows

•

Installing electrical wiring and pipes

•

Mounting wall xtures, electrical outlets, switches and lighting

•

Installing a drop ceiling

•

Painting

•

Installing closets

•

Laying tile and ooring

Charge the Tool and Monitor

Charge

NOTE:

The tool is shipped partially charged;

charge the battery before rst use.

Recharge the tool for approximately 5

hours after the battery depleted. It is not

recommended to recharge the tool for more

than 24 hours after each use.

a. Insert the USB interface of the USB charging

cable into the USB port of the power supply

(not included).

b. Insert the charging plug into charging port

of the tool, making sure that the two are

properly connected.

c. Connect the power supply (together with

USB charging cable) to the power outlet.(FIG. 2)

NOTE:

Do not operate the tool during charging.

The LED indicator for battery capacity will continuously icker in different colors during the

charging process.

•

The LED indicator for battery capacity ickers red during charging when the charged battery

capacity will allow the tool to be operated for approximately 30 minutes or less.

•

The LED indicator light ickers yellow during charging to indicate that the charged battery

capacity will allow the tool to be operated more than 30 minutes but has not reached 90% of

full capacity.

Fig. 2

Power Supply (Not

included)

Charging Plug

10

•

The LED indicator light ickers in green during charging to indicate that the charged battery

capacity has reached more than 90% of full capacity.

•

The LED indicator light steadily shines green when the battery has reached full charge

capacity.

Remember to remove the USB charging cable from tool when charging is complete.

During normal use, the LED indicator for battery capacity will illuminate continuously in

different colors to indicate approximately how much battery capacity remains.

•

When the LED indicator light illuminates green, it indicates that the battery charge is more

than 40% of full capacity.

•

When the LED indicator light illuminates yellow, it indicates that the battery charge is less

than 40% of full capacity.

•

When the LED indicator light illuminates red, it indicates that the tool can only be operated

for approximately 30 minutes before turning off automatically.

To Turn the Self-Leveling 360 Degree Cross Line Laser On and Off

WARNING

When turning on the Self-Leveling 360 degree Cross Line Laser,

always be aware of protecting your eyes and the eyes of those

around you. Never point the 360 Degree Cross Line Laser at anyone’s face, including

your own.

To turn the Self-Leveling 360 Degree Cross Line Laser on, push the mode switch in the

direction of the unlock icon, or press the laser button when the mode switch is in the direction

of the lock icon.

If the Self-Leveling 360 Degree Cross Line Laser is turned on with the mode switch in the

direction of unlock icon, push the mode switch in the direction of the lock icon to turn off.

If the Self-Leveling 360 Degree Cross Line Laser is turned on with the mode switch in the

direction of the lock icon, press the laser button repeatedly until it turns off.

Laser-Line Projection Modes

The Self-Leveling 360 Degree Cross Line Laser has three laser-projection modes. To select

a specic laser-projection mode, repeatedly press the laser button until you reach the desired

projection mode. This laser tool defaults to the cross-hair pattern mode when it is turned on.

To choose a projection mode, press the laser button:

•

Press the button once to select the horizontal laser line.

•

Press the button twice to select the vertical laser line.

•

In the Self-Leveling mode, press the button three times to return to the cross-hair pattern.

In manual leveling mode, press the button three times to turn the laser off. Press the laser

button again to restart with the cross-hair pattern.

11

Self-Leveling Mode (FIG. 3)

Your Self-Leveling 360 Degree Cross Line Laser has two working modes: self-leveling mode

and manual leveling mode.

In self-leveling mode, the tool will level itself if it is within ±4° of horizontal.

Place the Self-Leveling 360 Degree Cross Line Laser on a at, smooth surface that is within

±4° of horizontal.

Turn the tool on by sliding the mode switch in the direction of the unlock icon. The Self-

Leveling 360 Degree Cross Line Laser will automatically level within 6 seconds.

Press the laser button until the desired laser-projection mode is achieved and the laser line is

projected from the laser aperture.

If the surface on which the Self-Leveling 360 Degree Cross Line Laser is placed exceeds

±4° from horizontal, the laser line will blink as an alarm and the LED indicator for warning will

illuminate in red. In this event, adjust the angle of the surface slightly.

To turn off the laser lines, slide the mode switch in the direction of the lock icon.

Fig. 3

Manual Leveling Mode

Keep the mode switch in the lock icon position and press the laser button to turn on the laser.

The laser lines are now locked and are no longer self-leveling.

Press the laser button repeatedly to change the laser-projection mode: horizontal, vertical, or

cross-hair.

In manual leveling mode, the LED indicator for leveling status will always illuminate in red; the

laser lines are projected continuously and will not blink, even if the slope angle exceeds 4°.

Press the laser button repeatedly until the laser turns off.

12

Using With the Tripod

The tripod provides a stable, height-adjustable support (up to 43 inches).

Thread the ¼” screw on the tripod into the ¼” threaded mounting hole on the tool.

Tighten the tool with the tripod 1/4’’ screw platform.

Loosen locking knob 1. Rotate the crank until the desired height is attained. Tighten locking

knob 1 to lock in the center column in position. (FIG. 4)

Fig. 4

Manually raise the column to

the height desired

Loosen locking knob 2. Adjust the mounting

plate to the desired position; the maximum

adjustment scale is 90°. After adjustment,

tighten locking knob 2 to lock the mounting

plate in position (FIG. 5).

90

o

Fig. 5

13

Loosen locking knob 3 to pan the head left or right. The maximum adjustment scale is 360°.

After adjustment, tighten locking knob 3 to lock the position (FIG. 6).

360

o

Fig. 6

Loosen the handle by twisting it

counterclockwise. The mounting plate can

be tilted by moving the handle up or down;

the maximum adjustment scale is 360°. After

adjustment, tighten the handle clockwise to

lock the position. (FIG. 7)

360

o

Fig. 7

14

Open the 3 ip levers on one leg to release

that leg for adjustment. Extend the leg to the

proper height. Close the levers to lock the leg

in position. Repeat for the other two legs

(FIG. 8).

Fig. 8

15

MAINTENANCE

This tool has been designed to be a low-maintenance tool. However, in order to maintain its

performance, you must always follow these simple directions:

•

Avoid exposing the tool to shock, continuous vibration or extreme hot or cold temperatures.

•

Always store the tool indoors.

•

Always keep the tool free of dust and liquids. Use only a clean, soft cloth for cleaning. Avoid

using any solvents.

•

Do not disassemble the tool; this will expose the user to hazardous radiation exposure.

•

Do not attempt to change any part of the laser lens.

•

Do not dispose of this product in re; batteries inside the product may explode or leak.

•

After you have nished using the tool, always make sure that the switch is in the lock icon

position.

TROUBLE SHOOTING

Problem Cause Remedy

The laser line is not

projected.

The battery charge is too

low.

Charge the battery.

The laser line is hard to see. The tool is too far from the

target.

Move the tool closer to the

target.

The laser line ickers for

alert.

The surface where the

tool has been placed is

uneven or the tool is out of

its automatic Self-Leveling

range.

1. Place the tool on a more level

surface (within ±4°).

2. Set the tool to its manual

leveling mode.

For Recycling

To preserve natural resources, please recycle or dispose of batteries

properly. This product contains lithium-ion batteries. Local, state, or

federal laws may prohibit disposal of lithium-ion batteries in ordinary

trash. Consult your local waste authority for information regarding

available recycling and/ or disposal options.

16

LIMITED WARRANTY OF SKIL CONSUMER TOOLS

5 YEAR LIMITED WARRANTY- LEGAL

Chervon North America, Inc. ("Seller") warrants to the original purchaser only, that all SKIL

consumer TOOLS will be free from defects in material or workmanship for a period of ve

years from date of purchase, if original purchaser registers the product within 30 days from

purchase. BATTERIES AND CHARGERS are warranted for 2 years. Product registration

can be completed online at www.Registermyskil.com. Original purchasers should also retain

their receipt as proof of purchase. THE FIVE-YEAR WARRANTY PERIOD FOR TOOLS IS

CONDITIONED ON REGISTRATION OF THE PRODUCT WITHIN 30 DAYS OF PURCHASE.

If original purchasers do not register their product timely, the foregoing limited warranty will

apply for a duration of three years for tools. All batteries and chargers will remain under the

two-year limited warranty.

Notwithstanding the foregoing, if a SKIL consumer tool is used for industrial, professional

or commercial purposes, the foregoing warranty will apply for a duration of ninety days,

regardless of registration.

SELLER’S SOLE OBLIGATION AND YOUR EXCLUSIVE REMEDY under this Limited

Warranty and, to the extent permitted by law, any warranty or condition implied by law, shall

be the repair or replacement of parts, without charge, which are defective in material or

workmanship and which have not been misused, carelessly handled, or repaired by persons

other than Seller or Authorized Service Station. To make a claim under this Limited Warranty,

you must return the complete product, transportation prepaid, to any SKIL Factory Service

Center or Authorized Service Station. For Authorized SKIL Power Tool Service Stations,

please visit www.Registermyskil.com or call 1-877-SKIL-999 (1-877-754-5999).

THIS LIMITED WARRANTY DOES NOT APPLY TO ACCESSORY ITEMS SUCH AS

CIRCULAR SAW BLADES, DRILL BITS, ROUTER BITS, JIGSAW BLADES, SANDING

BELTS, GRINDING

WHEELS AND OTHER RELATED ITEMS.

ANY IMPLIED WARRANTIES APPLICABLE TO A PRODUCT SHALL BE LIMITED IN

DURATION EQUAL TO THE DURATION OF THE EXPRESS WARRANTIES APPLICABLE

TO SUCH PRODUCT, AS SET FORTH IN THE FIRST PARAGRAPH ABOVE. SOME STATES

IN THE U.S., SOME CANADIAN PROVINCES DO NOT ALLOW LIMITATIONS ON HOW

LONG AN IMPLIED WARRANTY LASTS, SO THE ABOVE LIMITATION MAY NOT APPLY TO

YOU.

IN NO EVENT SHALL SELLER BE LIABLE FOR ANY INCIDENTAL OR CONSEQUENTIAL

DAMAGES (INCLUDING BUT NOT LIMITED TO LIABILITY FOR LOSS OF PROFITS)

ARISING FROM THE

SALE OR USE OF THIS PRODUCT. SOME STATES IN THE U.S. AND SOME CANADIAN

PROVINCES DO NOT ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL OR

CONSEQUENTIAL

DAMAGES, SO THE ABOVE LIMITATION OR EXCLUSION MAY NOT APPLY TO YOU.

THIS LIMITED WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS, AND YOU MAY ALSO

HAVE OTHER RIGHTS WHICH VARY FROM STATE TO STATE IN THE U.S., PROVINCE

TO PROVINCE

IN CANADA AND FROM COUNTRY TO COUNTRY.

THIS LIMITED WARRANTY APPLIES ONLY TO PRODUCTS SOLD WITHIN THE UNITED

STATES OF AMERICA, CANADA AND THE COMMONWEALTH OF PUERTO RICO. FOR

WARRANTY COVERAGE WITHIN OTHER COUNTRIES, CONTACT YOUR LOCAL SKIL

DEALER OR IMPORTER.

02/20

Page is loading ...

32

CETTE GARANTIE LIMITÉE S’APPLIQUE UNIQUEMENT AUX ARTICLES VENDUS AUX

ÉTATS-UNIS D’AMÉRIQUE, AU CANADA ET À L’ÉTAT LIBRE DE PORTO RICO. POUR

CONNAÎTRE LA COUVERTURE DE LA GARANTIE DANS D’AUTRES PAYS, VEUILLEZ

COMMUNIQUER AVEC VOTRE DÉTAILLANT OU IMPORTATEUR SKIL LOCAL.

02/20

Page is loading ...

48

ESTA GARANTÍA LIMITADA SE APLICA SOLAMENTE A PRODUCTOS VENDIDOS EN

ESTADOS UNIDOS DE AMÉRICA, CANADÁ Y EL COMMONWEALTH DE PUERTO RICO.

PARA TENER UNA COBERTURA DE GARANTÍA EN OTROS PAÍSES, PÓNGASE EN

CONTACTO CON SU DISTRIBUIDOR O IMPORTADOR DE SKIL.

02/20

Skil LL9322G-01 Owner's manual

Skil LL9322G-01 Owner's manual

in other languages

Related papers

Other documents