2. Kichler Lighting
  3. 49899BKLED

Kichler Lighting 49899BKLED User manual

  • Hello! I am an AI chatbot trained to assist you with the Kichler Lighting 49899BKLED User manual. I’ve already reviewed the document and can help you find the information you need or explain it in simple terms. Just ask your questions, and providing more details will help me assist you more effectively!
Date Issued: 09/28/17 IS-49899LED-US
We’re here to help 866-558-5706
Hrs: M-F 9am to 5pm EST
CAUTION – RISK OF SHOCK –
Disconnect Power at the main circuit breaker panel or main
fusebox before starting and during the installation.
4) Make wire connections. Reference chart below for correct con-
nections and wire accordingly.
5) Carefullypushxture[5]towallmakingsurexturemounting
screws[2]passthroughxturemountingholes.
6) Make sure all connections remain secure and wires do not get
pinched.
7) Attachxture[5] to mounting plate using lock-up knobs[6].
INSTRUCTIONS FOR MOUNTING FIXTURE OUTDOORS
AND/OR IN WET LOCATIONS.
8) Mountingsurfaceshouldbeclean,dry,atand1/4”largerthat
thexturecanopyonallsides.Anygapsbetweenthemounting
surfaceandxturecanopyexceeding3/16”shouldbecor-
rected as required.
9) With silicone caulking compound, caulk the top and sides
whereedgeofxturecanopymeetsthewallsurfacetoprevent
waterfromenteringtheoutletbox.Thebottomofthexture
canopy should be left un-caulked.
WARNING:
Thisxtureisintendedforinstallationinaccordancewiththe
NationalElectricalCode(NEC)andalllocalcodespecications.
If you are not familiar with code requirements, installation by a
certiedelectricianisrecommended.
CLEANING:
Always be certain that electric current is turned off before cleaning.
Only a damp cloth should be used. Harsh cleaning products may
damagethenish.
FCC INFORMATION:
Thisdevicecomplieswithpart15oftheFCCRules.Operationis
subject to the following two conditions:
(1) Thisdevicemaynotcauseharmfulinterference,and
(2) thisdevicemustacceptanyinterferencereceived,including
interference that may cause undesired operation.
Note:Thisequipmenthasbeentestedandfoundtocomplywiththe
limitsforaClassBdigitaldevice,pursuanttopart15oftheFCC
Rules.Theselimitsaredesignedtoprovide
reasonable protection against harmful interference in a residential
installation.Thisequipmentgenerates,usesandcan
radiate radio frequency energy and, if not installed and used
in accordance with the instructions, may cause harmful
interferencetoradiocommunications.However,thereisno
guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference
toradioortelevisionreception,whichcanbedeterminedby
turning the equipment off and on, the user is encouraged to
try to correct the interference by one or more of the following mea-
sures:
• Reorientorrelocatethereceivingantenna.
• Increasetheseparationbetweentheequipmentandreceiver.
• Connect the equipment into an outlet on a circuit different from
thattowhichthereceiverisconnected.
• Consultthedealeroranexperiencedradio/TVtechnicianforhelp.
INSTALLATION:
• Read and understand all instructions and illustrations com-
pletely before proceeding with assembly and installation of
xture.
• Ifyouhaveanydoubtsabouthowtoinstallthisxture,orifthe
xturefailstooperatecompletely,pleasecontactaqualied
electrician.
• All parts must be used as indicated in the instructions. Do not
substituteanyparts,leavepartsout,oruseanypartsthatare
wornorbroken.Failuretoobeythisinstructioncouldinvalidate
theULlisting,C.S.A.certication,and/orETLlistingofthisxture.
• Fixtureistobeconnectedtoasinglebranchcircuit.
• Mountingsurfaceshouldbeclean,dry,atand1/4”largerthan
thexturehousingsurface.
INSTRUCTIONS:
1) Findtheappropriatethreadedholesonmountingstrap[1]
andassemblexturemountingscrews[2] into threaded holes.
Makesurexturemountingscrews[2] line up with mounting
holesinxture[5].
2) Attach mounting strap[1]tooutletbox[3] using mounting
screws[4]
.Themountingstrapcanbeadjustedtosuitposition
ofxture,
3) Groundinginstructions:(SeeIllus.AorB).
A) Onxtureswheremountingstrapisprovidedwithahole
andtworaiseddimples.Wrapgroundwirefromoutletbox
around green ground screw, and thread into hole.
B) Onxtureswhereacuppedwasherisprovided.Attach
groundwirefromoutletboxundercuppedwasherand
green ground screw, and thread into mounting strap.
Ifxtureisprovidedwithgroundwire.Connectxtureground
wiretooutletboxgroundwirewithwireconnector.(Notpro-
vided.)Afterfollowingtheabovesteps.Neverconnectground
wire to black or white power supply wires.
GREEN GROUND
SCREW
CUPPED
WASHER
OUTLET BOX
GROUND
FIXTURE
GROUND
DIMPLES
WIRE CONNECTOR
OUTLET BOX
GROUND
GREEN GROUND
SCREW
FIXTURE
GROUND
A
B
Connect Black or
Red Supply Wire to:
Connect
White Supply Wire to:
Black White
*Parallel cord (round & smooth) *Parallel cord (square & ridged)
Clear, Brown, Gold or Black
without tracer
Clear, Brown, Gold or Black
with tracer
Insulated wire (other than green)
with copper conductor
Insulated wire (other than green)
with silver conductor
*Note: When parallel wires (SPT I & SPT II)
are used. The neutral wire is square shaped
or ridged and the other wire will be round in
shape or smooth (see illus.)
Neutral Wire
1
2
3
4
5
6
/