Christie CP4320-RGB User manual

Service Guide

020-102713-03

Cinema 4K-RGB

CP4315-RGB, CP4320-RGB, CP4325-RGB, CP4330-

RGB

NOTICES

COPYRIGHT AND TRADEMARKS

Copyright

©

All brand names and product names are trademarks, registered trademarks or trade names of their respective holders.

GENERAL

Every effort has been made to ensure accuracy, however in some cases changes in the products or availability could occur which may not be reflected in this

document. Christie reserves the right to make changes to specifications at any time without notice. Performance specifications are typical, but may vary

depending on conditions beyond Christie's control such as maintenance of the product in proper working conditions. Performance specifications are based on

information available at the time of printing. Christie makes no warranty of any kind with regard to this material, including, but not limited to, implied

warranties of fitness for a particular purpose. Christie will not be liable for errors contained herein or for incidental or consequential damages in connection

with the performance or use of this material. Manufacturing facilities in Canada and China are ISO 9001 certified. Manufacturing facilities in Canada are also

ISO 14001 certified.

WARRANTY

Products are warranted under Christie’s standard limited warranty, the complete details of which are available by contacting your Christie dealer or Christie. In

addition to the other limitations that may be specified in Christie’s standard limited warranty and, to the extent relevant or applicable to your product, the

warranty does not cover:

a.

Problems or damage occurring during shipment, in either direction.

b.

Problems or damage caused by combination of a product with non-Christie equipment, such as distribution systems, cameras, DVD players, etc., or use

of a product with any non-Christie interface device.

c.

Problems or damage caused by misuse, improper power source, accident, fire, flood, lightning, earthquake, or other natural disaster.

d.

Problems or damage caused by improper installation/alignment, or by equipment modification, if by other than Christie service personnel or a Christie

authorized repair service provider.

e.

Use of third party product enclosures for environmental protection during outside use must be approved by Christie.

f.

Problems or damage caused by use of a product on a motion platform or other movable device where such product has not been designed, modified or

approved by Christie for such use.

g.

Except where the product is designed for outdoor use, problems or damage caused by use of the product outdoors unless such product is protected from

precipitation or other adverse weather or environmental conditions and the ambient temperature is within the recommended ambient temperature set

forth in the specifications for such product.

h.

Defects caused by normal wear and tear or otherwise due to normal aging of a product.

The warranty does not apply to any product where the serial number has been removed or obliterated. The warranty also does not apply to any product sold

by a reseller to an end user outside of the country where the reseller is located unless (i) Christie has an office in the country where the end user is located or

(ii) the required international warranty fee has been paid.

The warranty does not obligate Christie to provide any on site warranty service at the product site location.

PREVENTATIVE MAINTENANCE

Preventative maintenance is an important part of the continued and proper operation of your product. Failure to perform maintenance as required, and in

accordance with the maintenance schedule specified by Christie, will void the warranty. For preventative maintenance schedules, refer to

www.christiedigital.com.

REGULATORY

The product has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed

to provide reasonable protection against harmful interference when the product is operated in a commercial environment. The product generates, uses, and

can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio

communications. Operation of the product in a residential area is likely to cause harmful interference in which case the user will be required to correct the

interference at the user’s own expense. Changes or modifications not expressly approved by the party responsible for compliance could void the user's

authority to operate the equipment

CAN ICES-3 (A) / NMB-3 (A)

이 기기는 업무용(A급)으로 전자파적합등록을 한 기기이오니 판매자 또는 사용자는 이점을 주의하시기 바라며, 가정 외의 지역에서 사용하는 것을 목적으로 합니다.

ENVIRONMENTAL

The product is designed and manufactured with high-quality materials and components that can be recycled and reused. This symbol

means that electrical

and electronic equipment, at their end-of-life, should be disposed of separately from regular waste. Please dispose of the product appropriately and according

to local regulations. In the European Union, there are separate collection systems for used electrical and electronic products. Please help us to conserve the

environment we live in!

Content

Introduction...................................................... 6

Site requirements...................................................6

Projector components (front)............................................7

Projector components (rear)............................................ 8

Security roles......................................................8

Product documentation................................................9

Related documentation.............................................10

Service guidelines.................................................11

Ordering parts.................................................... 11

Replacing modules..................................................11

Interconnections and line drawings....................................... 11

Servicing live equipment..............................................11

Safety precautions..................................................12

General safety precautions...........................................12

Laser safety precautions............................................13

AC power precautions..............................................13

Light intensity hazard distance..........................................14

Product labels.....................................................17

General hazards................................................. 17

Mandatory action.................................................18

Electrical labels..................................................18

Additional hazard labels............................................ 18

Service setups................................................... 20

Turning the projector on or off.......................................... 20

Calibrating the Intelligent Lens System.....................................20

Adjusting boresight................................................. 20

Adjusting the integrator rod and fold mirror..................................23

Adjusting DMD convergence............................................26

Adjusting the LOS coupling mirror........................................28

Replacing or refilling the coolant.........................................28

Parts and module replacement.......................................30

Tools required for service..............................................30

Cinema 4K-RGB Service Guide–CP4315-RGB, CP4320-RGB, CP4325-RGB, CP4330-RGB 3

020-102713-03 Rev. 1 (11-2019)

Copyright

©

Maintenance prerequisites.............................................30

Index of parts and modules............................................31

Lens mount components........................................... 34

Removing the projection lens...........................................34

Replacing the lens mount..............................................34

Filtration........................................................37

Replacing the light engine compartment air filter...............................37

Replacing the main intake air filter........................................38

Projector covers and feet...........................................39

Removing the top cover.............................................. 39

Removing the touch panel.............................................40

Removing the rear cover..............................................40

Removing the electronics-side cover.......................................41

Removing the front cover............................................. 42

Removing the side-intake cover..........................................42

Removing the bottom cover............................................43

Electronics......................................................45

Servicing the card cage...............................................45

Removing the AC breaker............................................. 46

Replacing the power supplies...........................................47

Removing the laser driver card cage.......................................51

Replacing the temperature sensor........................................53

Replacing the SID harness.............................................53

Replacing the mini-SAS cables.......................................... 54

Ventilation and cooling.............................................55

Replacing the card cage intake fan (#1).................................... 55

Replacing the blue formatter fan (#3)......................................55

Replacing the green formatter fan (#4).....................................56

Replacing the red formatter fan (#5)...................................... 57

Replacing the card cage exhaust fan (#4)................................... 58

Replacing the radiator intake fans (#6-17)...................................59

Replacing the laser driver card cage fans (#21-24)............................. 59

Replacing the light engine intake fans (#25-30)............................... 60

Removing the coolant reservoir..........................................62

Removing the pump module............................................62

Content

Cinema 4K-RGB Service Guide–CP4315-RGB, CP4320-RGB, CP4325-RGB, CP4330-RGB 4

020-102713-03 Rev. 1 (11-2019)

Copyright

©

Replacing the radiator................................................63

Replacing the relief tank..............................................65

Replacing the exhaust duct............................................ 65

Optics..........................................................67

Replacing the integrator assembly........................................67

Replacing the fold mirror adjust..........................................69

Replacing the light dump..............................................70

Replacing the light engine.............................................71

Packing the existing light engine.........................................72

Replacing the LOS coupling elbow........................................ 75

Removing the coupling elbow mirror assembly................................ 76

Replacing the shutter................................................77

Printed circuit boards and sensors....................................78

Replacing the F-Main electronics card......................................78

Replacing the IMB..................................................79

Replacing the housekeeping board (HKBB)...................................80

Replacing the SCCB.................................................81

Replacing the HUB-NX............................................... 82

Replacing the dual temperature sensor module (DTSM)...........................83

Replacing the status LED board (SLB)......................................84

Replacing the low voltage current source (LVCS) board...........................85

Replacing the high voltage current source boards...............................86

Replacing the laser backplane (LBP7) board..................................87

Replacing the diffuser control board (DIB PCB)................................88

Replacing the color sensor board.........................................88

Replacing the color sensor board harness..................................90

Performing the DAC calibration........................................92

Performing the LiteLOC v1 calibration....................................93

Content

Cinema 4K-RGB Service Guide–CP4315-RGB, CP4320-RGB, CP4325-RGB, CP4330-RGB 5

020-102713-03 Rev. 1 (11-2019)

Copyright

©

Introduction

This document provides technical information for assisting Christie qualified technicians in the

servicing of the Cinema 4K-RGB projector.

Every effort has been made to make sure the information in this document is accurate and complete.

However, due to continuing research all information is subject to change without notice. Christie

assumes no responsibility for omissions or inaccuracies.

Site requirements

To safely install and operate the Cinema 4K-RGB projectors, the installation location must meet these

minimum requirements.

Physical operating environment

• Ambient temperature (operating) 10°C to 35°C (50°F to 95°F)

• Humidity (non-condensing) 10% to 80%

• Operating altitude 0 to 3000 meters (0 to 9843 feet)

External exhaust ducting

Sufficient ventilation is required around the projector to regulate the temperature of the internal laser

module. If necessary, air intake and exhaust HVAC ducts can be installed.

An exhaust duct is also available for purchase as an optional accessory (P/N: 163-102104-XX).

Instructions for installing the exhaust duct are included with the accessory part.

The installation site must provide an airflow 450 cubic feet per minute (CFM) at 1 to 1000 meters

elevation, and must accommodate a heat load of 4 kW.

For each additional 1000 meters above sea level, increase the airflow (CFM) value by 15%. If an

extraction duct is not used, the operating temperature range is restricted to 10°C to 25°C at a maximum

altitude of 3000 meters.

Permanent power connection

A 30 A maximum rated, certified wall circuit breaker is required. It must be part of the building and

easily accessible.

The projector must be connected to power using a hard-wired connection. The projector light source

requires the permanent AC connection to operate. There is also an available connector for an

uninterruptible power supply (UPS) to provide backup power for the projector electronics only.

Cinema 4K-RGB Service Guide–CP4315-RGB, CP4320-RGB, CP4325-RGB, CP4330-RGB 6

020-102713-03 Rev. 1 (11-2019)

Copyright

©

Projector components (front)

Learn about the components on the front of the projector.

A Projector lens

A list of available lenses is available in the projector specifications. For more information, see the

Cinema 4K-RGB Specifications Guide (P/N: 020-102729-XX).

B Adjustable feet

Turn the adjustable feet to increase or decrease the projector height.

C Service access door

D Communications panel

External devices are connected here.

Introduction

Cinema 4K-RGB Service Guide–CP4315-RGB, CP4320-RGB, CP4325-RGB, CP4330-RGB 7

020-102713-03 Rev. 1 (11-2019)

Copyright

©

E Top cover

Projector components (rear)

Learn about the components on the rear of the projector.

A Touch panel

A touch-sensitive screen used to control the projector.

B AC circuit breakers

C Air exhaust

D Power cord and AC receptacle

E Air intake

Security roles

Only Christie authorized service technicians should perform field repair, marriage setup, and service to

the unit.

Theater personnel should only perform diagnostic functions, such as running the projector

interrogator. After performing a procedure that mandates use of the high security key, theater

personnel must ensure the security of the system is reestablished.

Introduction

Cinema 4K-RGB Service Guide–CP4315-RGB, CP4320-RGB, CP4325-RGB, CP4330-RGB 8

020-102713-03 Rev. 1 (11-2019)

Copyright

©

Product documentation

For installation, setup, and user information, see the product documentation available on the Christie

website. Read all instructions before using or servicing this product.

1. Access the documentation from the Christie website:

CP4315-RGB

• Go to http://bit.ly/30mhBGx or https://www.christiedigital.com/en-us/cinema/cinema-

products/digital-cinema-projectors/christie-cp4315-rgb

• Scan the QR code using a QR code reader app on a smartphone or tablet.

CP4320-RGB

• Go to http://bit.ly/2Z6F7uA or https://www.christiedigital.com/en-us/cinema/cinema-

products/digital-cinema-projectors/christie-cp4320-rgb

• Scan the QR code using a QR code reader app on a smartphone or tablet.

CP4325-RGB

• Go to http://bit.ly/2BjQLBq or https://www.christiedigital.com/en-us/cinema/cinema-

products/digital-cinema-projectors/christie-cp4325-rgb

• Scan the QR code using a QR code reader app on a smartphone or tablet.

CP4330-RGB

• Go to http://bit.ly/2IRKIwW or https://www.christiedigital.com/en-us/cinema/cinema-

products/digital-cinema-projectors/christie-cp4330-rgb

• Scan the QR code using a QR code reader app on a smartphone or tablet.

Introduction

Cinema 4K-RGB Service Guide–CP4315-RGB, CP4320-RGB, CP4325-RGB, CP4330-RGB 9

020-102713-03 Rev. 1 (11-2019)

Copyright

©

2. Switch to the Downloads tab.

Related documentation

Additional information on the projector is available in the following documents.

• Cinema 4K-RGB Installation and Setup Guide (P/N: 020-102710-XX)

• Cinema 4K-RGB User Guide (P/N: 020-102712-XX)

• Cinema 4K-RGB Product Safety Guide (P/N: 020-102711-XX)

• CineLife Serial Commands Guide (P/N: 020-102714-XX)

• Cinema 4K-RGB Specifications Guide (P/N: 020-102729-XX)

Introduction

Cinema 4K-RGB Service Guide–CP4315-RGB, CP4320-RGB, CP4325-RGB, CP4330-RGB 10

020-102713-03 Rev. 1 (11-2019)

Copyright

©

Service guidelines

Review safety guidelines and information required for replacing modules.

Ordering parts

When ordering replacement parts, quote the part numbers of the items required. Quote the projector

model number, serial number, and date of manufacture, as indicated on the license label.

Not all parts are available separately. In addition, some parts stocked as inventory are available only

until the current supply lasts.

All part numbers are subject to change.

Replacing modules

To ensure you have the correct module and the projector module is replaced correctly, check module

markings, parts lists, and the relevant disassembly and replacement procedures.

Components must be replaced with exact equivalents or Christie approved replacement parts. Failure

to do so may result in unsafe operation.

Interconnections and line drawings

The interconnect diagram illustrates the path of electrical connections between modules.

Manufacturer’s part numbers are included. Part numbers are subject to change.

Line drawings provide projector dimensions and sizes for installation.

To download the latest interconnect diagram or line drawings, visit www.christiedigital.com.

Servicing live equipment

Only Christie accredited technicians who are knowledgeable about the hazards associated with

hazardous voltage and high temperatures are authorized to assemble, install, and service Christie

equipment.

To make sure you remain safe when servicing energized (live) Christie equipment:

• Locate the main AC power shut off prior to servicing the equipment. This will allow you to turn

the power off quickly in an emergency.

• Disconnect the projector from the communication and management network so it cannot

receive commands to turn the light source on, open the shutter, and move the lens.

• Familiarize yourself with all potential safety hazards prior to servicing the equipment. This

includes, but is not limited to, the location and accessibility of hazardous voltages.

Cinema 4K-RGB Service Guide–CP4315-RGB, CP4320-RGB, CP4325-RGB, CP4330-RGB 11

020-102713-03 Rev. 1 (11-2019)

Copyright

©

• Read and understand all written procedures prior to commencing a service procedure.

• Understand and follow all local safety codes and requirements when servicing energized (live)

equipment.

• Perform equipment service in a location free of obstructions and other hazards. For example,

you must have an unobstructed view of the area being serviced.

Wear personal protective equipment (PPE) clothing appropriate to the service you are performing. This

includes, but is not limited to, protective (electrically insulated) footwear, safety glasses, and gloves

rated for the working voltage of the equipment you are servicing.

Safety precautions

Learn about the safety precautions related to the Christie Cinema 4K-RGB projector. This projector is

intended for use in a cinema environment.

General safety precautions

Read all safety and warning guidelines before installing or operating the projector.

Warning! If not avoided, the following could result in death or serious injury.

• TRIP OR FIRE HAZARD! Position all cables where they cannot contact hot surfaces, be pulled, be

tripped over, or damaged by persons walking on or objects rolling over the cables.

• This product must be installed within a restricted access location not accessible by the general

public.

• Only personnel who are trained on the precautions for the restricted access location can be

granted entry to the area.

• Install the product so users and the audience cannot enter the restricted area at eye level.

• ELECTRICAL and BURN HAZARD! Use caution when accessing internal components.

• High leakage current present when connected to IT power systems.

• FIRE AND SHOCK HAZARD! Use only the attachments, accessories, tools, and replacement parts

specified by Christie.

• FIRE HAZARD! Do not use a power cord, harness, or cable that appears damaged.

• A minimum of four people or appropriately rated lift equipment is required to safely lift, install,

or move the product.

• Do not install or operate the projector in any position that does not meet the stated product

specifications for alignment and orientation.

Caution! If not avoided, the following could result in minor or moderate injury.

• Only Christie qualified technicians are permitted to open product enclosures.

Service guidelines

Cinema 4K-RGB Service Guide–CP4315-RGB, CP4320-RGB, CP4325-RGB, CP4330-RGB 12

020-102713-03 Rev. 1 (11-2019)

Copyright

©

Laser safety precautions

Read all safety and warning guidelines before operating the projector laser.

Warning! If not avoided, the following could result in death or serious injury.

• Do not operate the cinema projector without all of its covers in place.

• LASER RADIATION HAZARD! This projector has a built-in Class 4 laser module. Never attempt to

disassemble or modify the laser module.

• Do not look directly into the lens when the light source is on. The extremely high brightness can

cause permanent eye damage.

• Possible hazardous optical radiation emitted from this product. (Risk group 3)

AC power precautions

Read all safety and warning guidelines before connecting to AC power.

Warning! If not avoided, the following could result in death or serious injury.

• SHOCK HAZARD! Only use the AC power cord provided with the product or recommended by

Christie.

• FIRE AND SHOCK HAZARD! Do not attempt operation unless the power cord, power socket, and

power plug meet the appropriate local rating standards.

• SHOCK HAZARD! Do not attempt operation if the AC supply is not within the specified voltage

and current, as specified on the license label.

• SHOCK HAZARD! The optional UPS power cord must be inserted into an outlet with grounding.

• SHOCK HAZARD! A dedicated, protected ground or earth wire must be installed on the product

by Christie qualified technicians or electricians before it can be connected to power.

• SHOCK HAZARD! Disconnect the product from AC before installing, moving, servicing, cleaning,

removing components, or opening any enclosure.

• Install the product near an easily accessible AC receptacle.

Caution! If not avoided, the following could result in minor or moderate injury.

• FIRE HAZARD! Do not use a power cord, harness, or cable that appears damaged.

• FIRE OR SHOCK HAZARD! Do not overload power outlets and extension cords.

• SHOCK HAZARD! Power supply uses double pole/neutral fusing.

Service guidelines

Cinema 4K-RGB Service Guide–CP4315-RGB, CP4320-RGB, CP4325-RGB, CP4330-RGB 13

020-102713-03 Rev. 1 (11-2019)

Copyright

©

Light intensity hazard distance

This projector has been classified as Risk Group 3 as per the IEC 62471-5:2015 standard due to

possible hazardous optical and thermal radiation being emitted.

Warning! If not avoided, the following could result in serious injury.

• PERMANENT/TEMPORARY BLINDNESS HAZARD! No direct exposure to the beam must be

permitted. Class 1 Laser Product - Risk Group 3 according to IEC 60825-1:2014 and IEC

62471-5:2015.

• PERMANENT/TEMPORARY BLINDNESS HAZARD! Operators must control access to the beam

within the hazard distance or install the product at the height that prevents exposure of

spectators' eyes within the hazard distance. The hazard zone must be no lower than 2.5 meters

(US installations) or 2.0 meters (global installations) above any surface upon which any persons

are permitted to stand and the horizontal clearance to the hazard zone must be a minimum 1.0

meters.

• EXTREME BRIGHTNESS! Do not place reflective objects in the product light path.

The following diagram and table show the zones for ocular and skin hazard distances:

• A—Hazard zone. The region of space where the projection light from the laser-illuminated

projector is above emission limits for Risk Group 2. The light intensity may cause eye damage

after a momentary or brief exposure (before a person can avert his or her eyes away from the

light source). The light may cause skin burns to occur.

• B—Hazard distance. Operators must control access to the beam within the hazard distance or

install the product preventing potential exposure of the spectators' eyes from being in the

hazard distance.

• C—No access zone. Horizontal clearance of the no access zone must be a minimum of 1.0

meters.

• D—Vertical distance to hazard zone. The hazard zone must be no lower than 2.5 meters (US

installations) or 2.0 meters (global installations) above any surface upon which any persons

are permitted to stand.

• E—Represents the top view of the projector.

Service guidelines

Cinema 4K-RGB Service Guide–CP4315-RGB, CP4320-RGB, CP4325-RGB, CP4330-RGB 14

020-102713-03 Rev. 1 (11-2019)

Copyright

©

• F—Represents the side view of the projector.

For US market only, hazard distances based upon FDA guidance document 1400056, Classification and

Requirements for Laser Illuminated Projectors (LIPs), dated February 18, 2015.

CP4315-RGB, CP4320-RGB, CP4330-RGB

Projection Lens

(Throw Ratio 4K)

Part

Number

Hazard Distance (m)

CP4315-RGB CP4320-RGB CP4330-RGB

0.90:1 HB fixed lens 38-809071-XX 0.9 1.0 1.2

1.13-1.66:1 DLPCine HB zoom lens 108-342100-XX 1.5 1.8 2.0

1.31-1.85:1 DLPCine HB zoom lens 108-335102-XX 1.7 2.0 2.5

1.45-2.17:1 DLPCine HB zoom lens 108-336103-XX 2.1 2.3 2.6

1.63-2.71:1 DLPCine HB zoom lens 108-337104-XX 2.4 2.8 3.2

1.95-3.26:1 DLPCine HB zoom lens 108-338105-XX 3.0 3.4 3.8

2.71-3.89:1 DLPCine HB zoom lens 108-278101-XX 3.5 4.1 4.3

3.89-5.43:1 DLPCine HB zoom lens 108-279101-XX 5.0 5.7 5.8

4.98-7.69:1 DLPCine HB zoom lens 108-280101-XX 7.1 8.3 9.6

1.13-1.66:1 DLPCine UHC zoom lens 163-103105-XX 1.4 1.6 1.8

1.31-1.85:1 DLPCine UHC zoom lens 163-104106-XX 1.6 1.8 2.0

1.45-2.17:1 DLPCine UHC zoom lens 163-105107-XX 1.9 2.1 2.3

1.63-2.71:1 DLPCine UHC zoom lens 163-106108-XX 2.2 2.5 2.6

1.95-3.26:1 DLPCine UHC zoom lens 163-107109-XX 2.7 3.0 3.2

2.71-3.89:1 DLPCine UHC zoom lens 163-108100-XX 3.2 3.6 3.8

3.89-5.43:1 DLPCine UHC zoom lens 163-109101-XX 4.6 5.2 5.7

4.98-7.69:1 DLPCine UHC zoom lens 163-110103-XX 6.6 7.4 8.3

CP4325-RGB

For US market only, hazard distances based upon FDA guidance document 1400056, Classification and

Requirements for Laser Illuminated Projectors (LIPs), dated February 18, 2015.

Projection Lens Part Number Hazard Distance

(m)

0.90:1 HB fixed lens 38-809071-XX 1.4

1.13-1.66:1 DLPCine HB zoom lens 108-342100-XX 2.3

1.31-1.85:1 DLPCine HB zoom lens 108-335102-XX 2.6

1.45-2.17:1 DLPCine HB zoom lens 108-336103-XX 3.2

1.63-2.71:1 DLPCine HB zoom lens 108-337104-XX 4.0

1.95-3.26:1 DLPCine HB zoom lens 108-338105-XX 4.3

Service guidelines

Cinema 4K-RGB Service Guide–CP4315-RGB, CP4320-RGB, CP4325-RGB, CP4330-RGB 15

020-102713-03 Rev. 1 (11-2019)

Copyright

©

Projection Lens Part Number Hazard Distance

(m)

2.71-3.89:1 DLPCine HB zoom lens 108-278101-XX 5.1

3.89-5.43:1 DLPCine HB zoom lens 108-279101-XX 8.3

1.13-1.66:1 DLPCine UHC zoom lens 163-103105-XX 1.8

1.31-1.85:1 DLPCine UHC zoom lens 163-104106-XX 2.5

1.45-2.17:1 DLPCine UHC zoom lens 163-105107-XX 3.0

1.63-2.71:1 DLPCine UHC zoom lens 163-106108 -XX 3.7

1.95-3.26:1 DLPCine UHC zoom lens 163-107109-XX 4.3

3.0-4.3:1 DLPCine UHC zoom lens 163-108100-XX 5.1

For all other markets, hazard distances based upon IEC 62471-5:2015, Photobiological safety of lamps

and lamp systems – Part 5: Image projectors.

Projection Lens

(Throw Ratio 4K)

Part Number Hazard Distance

(m)

0.90:1 HB fixed lens 38-809071-XX 1.0

1.13-1.66:1 DLPCine HB zoom lens 108-342100-XX 1.2

1.31-1.85:1 DLPCine HB zoom lens 108-335102-XX 1.4

1.45-2.17:1 DLPCine HB zoom lens 108-336103-XX 1.9

1.63-2.71:1 DLPCine HB zoom lens 108-337104-XX 2.4

1.95-3.26:1 DLPCine HB zoom lens 108-338105-XX 2.9

2.71-3.89:1 DLPCine HB zoom lens 108-278101-XX 3.4

3.89-5.43:1 DLPCine HB zoom lens 108-279101-XX 4.0

1.13-1.66:1 DLPCine UHC zoom lens 163-103105-XX 1.0

1.31-1.85:1 DLPCine UHC zoom lens 163-104106-XX 1.1

1.45-2.17:1 DLPCine UHC zoom lens 163-105107-XX 1.4

1.63-2.71:1 DLPCine UHC zoom lens 163-106108-XX 2.0

1.95-3.26:1 DLPCine UHC zoom lens 163-107109-XX 2.5

3.0-4.3:1 DLPCine UHC zoom lens 163-108100-XX 3.1

For Installations in the United States

The following must be in place for laser-illuminated projector installations in the United States:

• The projection room shall be clearly identified by the posting of laser warning and restricted

access signs, and by restricting entry through physical means. The projection room sign must

display the warning "No direct exposure to beam shall be permitted".

Service guidelines

Cinema 4K-RGB Service Guide–CP4315-RGB, CP4320-RGB, CP4325-RGB, CP4330-RGB 16

020-102713-03 Rev. 1 (11-2019)

Copyright

©

• The Christie Laser Projection System Installation Checklist must be fully completed after the

installation and sent to [email protected]. A copy can remain on-site. This

checklist can be found as a separate document in the accessory box with the manual.

• Certain US states have additional laser regulatory requirements. Go to www.christiedigital.com

for additional regulatory requirements.

Product labels

Learn about the labels that may be used on the product. Labels on your product may be yellow or

black and white.

General hazards

Hazard warnings also apply to accessories once they are installed in a Christie product that is

connected to power.

Fire and Shock Hazard

To prevent fire or shock hazards, do not expose this product to rain or moisture.

Do not alter the power plug, overload the power outlet, or use it with extension cords.

Do not remove the product enclosure.

Only Christie qualified technicians are authorized to service the product.

Electrical Hazard

Risk of electric shock.

Do not remove the product enclosure.

Only Christie qualified technicians are authorized to service the product.

General hazard.

Electric shock hazard. To avoid personal injury, disconnect all power sources before

performing maintenance or service.

Electrocution hazard. To avoid personal injury, always disconnect all power sources before

performing maintenance or service procedures.

Hot surface hazard. To avoid personal injury, allow the product to cool for the recommended

cool down time before performing maintenance or service.

Burn hazard. To avoid personal injury, allow the product to cool for the recommended cool

down time before performing maintenance or service.

Optical radiation hazard. To avoid personal injury, never look directly at the light source.

Service guidelines

Cinema 4K-RGB Service Guide–CP4315-RGB, CP4320-RGB, CP4325-RGB, CP4330-RGB 17

020-102713-03 Rev. 1 (11-2019)

Copyright

©

Moving parts hazard. To avoid personal injury, keep hands clear and loose clothing tied back.

Fan hazard. To avoid personal injury, keep hands clear and loose clothing tied back. Always

disconnect all power sources before performing maintenance or service procedures.

Voltage hazard. To avoid personal injury, always disconnect all power sources before

performing maintenance or service procedures.

Not for household use.

Mandatory action

Consult the service manual.

Disconnect all power sources before performing maintenance or service procedures.

Electrical labels

Indicates the presence of a protective earth ground.

Indicates the presence of an earth ground.

Additional hazard labels

Indicates Class 4 laser radiation when open. Avoid eye or skin

exposure to direct or scattered radiation.

CLASS 1 LASER PRODUCT IEC 60825-1:2014

CP4325-RGB FDA laser variance (US projectors only)

Service guidelines

Cinema 4K-RGB Service Guide–CP4315-RGB, CP4320-RGB, CP4325-RGB, CP4330-RGB 18

020-102713-03 Rev. 1 (11-2019)

Copyright

©

CP4330-RGB FDA laser variance (US projectors only)

Indicates a light hazard. Do not look directly into the lens. The

extreme high brightness can cause permanent eye damage. Class 1

Laser Product - Risk Group 3 according to IEC 60825-1:2014 and

IEC 62471-5:2015

Indicates high leakage current. Earth connection essential before

connecting the power supply.

Indicates a light hazard. Do not look directly into the lens. The

extreme high brightness can cause permanent eye damage.

Service guidelines

Cinema 4K-RGB Service Guide–CP4315-RGB, CP4320-RGB, CP4325-RGB, CP4330-RGB 19

020-102713-03 Rev. 1 (11-2019)

Copyright

©

Service setups

Understand the special internal hardware and software adjustments and related details that may

require the attention of a qualified service technician, whether done periodically or after a specific

module replacement.

Turning the projector on or off

Turn on the projector to display content, or turn off the projector to conserve energy or service the

projector.

To operate the projector, the circuit breakers must be in the ON position. If you are servicing the

projector or removing the protective covers, ensure that the MAIN and UPS circuit breakers are in the off

position.

• In the right toolbar, tap and hold Power.

If the light source is on when turning off the projector, the light source enters a ten-minute

cool-down period automatically.

Calibrating the Intelligent Lens System

On Cinema 4K-RGB projectors, the Intelligent Lens System (ILS) is activated by default.

Use the Auto Calibrate feature of the ILS to find and compensate for motor backlash, and to determine

the movement range for the currently installed lens.

1. In the left navigation menu, tap Image Settings > ILS File Setup.

2. From the ILS File list, select an available ILS file.

3. Tap Auto Calibrate.

4. Tap Continue.

The system performs the lens calibration.

Adjusting boresight

A boresight adjustment balances the tilt of the lens mount to compensate for screen-to-projector tilt.

Warning! If not avoided, the following could result in death or serious injury.

• Do not look directly into the lens when the light source is on. The extremely high brightness can

cause permanent eye damage.

• FIRE HAZARD! Keep hands, clothes, and all combustible material away from the concentrated

light beam of the projector.

Caution! If not avoided, the following could result in minor or moderate injury.

• This procedure must be performed by Christie qualified technicians.

Cinema 4K-RGB Service Guide–CP4315-RGB, CP4320-RGB, CP4325-RGB, CP4330-RGB 20

020-102713-03 Rev. 1 (11-2019)

Copyright

©

Page is loading ...

Christie CP4320-RGB, CP4315-RGB, CP4330-RGB User manual

Related papers

Other documents