Avaya 1151C1/1151C2 User manual

Brand: Avaya

Model: 1151C1/1151C2

Type: User manual

1151C1/1151C2 Power Supply

Installation and Safety Instructions

IMPORTANT USER SAFETY INSTRUCTIONS

The most careful attention has been devoted to quality standards in the manufacture of

your new power supply. Safety is a major factor in the design of every Avaya Product.

But, safety is YOUR responsibility too. Please read carefully the helpful tips listed

below. These suggestions will enable you to take full advantage of this product. Then,

retain these tips for later use.

WARNING:

This product is NOT for residential use. It is for business systems applications

ONLY.

Use

When using your power supply, the following safety precautions should always be

followed to reduce the risk of fire, electric shock, and injury to persons.

• Read and understand all instructions.

• Follow all warnings and instructions marked on the product and contained in its

packaging.

• The 1151C1/C2 Power Supplies are for use only with specified Avaya equipment as

outlined in the attached materials or available on

http://www.avaya.com/support.

No other use of the 1151C1/C2 Power supplies is recommended or warranted

• The equipment must not be connected to TNV-3 (standard analog phone lines) or

TNV-2 circuits.

• For Australia, the equipment must not be connected to any TNV circuit.

• The equipment must not be installed in proximity to standard phone lines.

• This device can be hazardous if immersed in water. Do not use this product near

water, for example, near a bath tub, wash bowl, kitchen sink or laundry tub, in a wet

basement or near a swimming pool. To avoid the possibility of electric shock, do not

use it while you are wet. If you accidentally drop the power supply into water, do not

retrieve it until you have first unplugged the line cord from the modular wall jack,

unplugged the power cord from the AC wall receptacle (or other AC power source),

and unplugged the output cable from any device powered by the supply. Then, call

service personnel to ask about a replacement.

• This product should be operated only from the type of AC power indicated on the

product label. If you are unsure of the type of AC power being provided, contact a

qualified service person.

• Do not allow anything to rest on the power cord. Do not locate this product where

the cord will be abused, such as by persons walking on it.

• Allow adequate ventilation for the product. Do not cover or install in a confined

space that may prevent cooling and allow excessive heat build-up.

• To reduce the risk of electric shock, do not disassemble this product. There are no

user serviceable parts. Opening or removing covers may expose you to hazardous

voltages. Incorrect reassembly can cause electric shock when the product is

subsequently used.

• The Avaya model 1151C2 power supply contains a non-spillable sealed lead-acid

battery. Reasonable care should be taken to avoid puncturing, or otherwise

compromising the integrity of the battery housing. Recycle the battery properly.

CAUTION:

RISK OF EXPLOSION IF BATTERY IS REPLACED BY AN INCORRECT TYPE.

DISPOSE OF USED BATTERIES ACCORDING TO THE INSTRUCTIONS.

Service

• Before cleaning or removing from service, unplug the power supply from the

modular wall jack, unplug the power cord from the AC wall receptacle (or other AC

power source), and unplug the output cable from any device powered by the

supply. Do not use liquid cleaners or aerosol cleaners. Use a damp cloth for

cleaning.

• Be sure to disconnect all cords from this product and refer servicing to qualified

service personnel when these conditions exist:

— If the power supply cord is damaged or frayed.

— If liquid has been spilled into the product.

— If the product has been exposed to rain or water.

— If the product has been dropped or the housing has been damaged.

— If you note a distinct change in the performance of the product.

Declaration of Conformity

To download the Declaration of Conformity (DoC) for this equipment, visit

http://www.avaya.com/support

SAVE THESE INSTRUCTIONS

When you see this warning symbol on the product, refer to

this instructions booklet for more information before

proceeding.

16-600743

Issue 3, September 2008

Page is loading ...

Notice

Every effort was made to ensure that the information in this document

was complete and accurate at the time of printing. However, information

is subject to change.

Warranty

Avaya Inc. provides a limited warranty on this product. Refer to your

sales agreement to establish the terms of the limited warranty. In

addition, Avaya's standard warranty language as well as information

regarding support for this product, while under warranty, is available

through the following Web site: http://www.avaya.com/support

Disclaimer

Avaya is not responsible for any modifications, additions or deletions to

the original published version of this documentation unless such

modifications, additions or deletions were performed by Avaya. Customer

and/or End User agree to indemnify and hold harmless Avaya, Avaya's

agents, servants and employees against all claims, lawsuits, demands

and judgments arising out of, or in connection with, subsequent

modifications, additions or deletions to this documentation to the extent

made by the Customer or End User.

Standards Compliance

Avaya Inc. is not responsible for any radio or television interference

caused by unauthorized modifications of this equipment or the

substitution or attachment of connecting cables and equipment other

than those specified by Avaya Inc. The correction of interference caused

by such unauthorized modifications, substitution or attachment will be the

responsibility of the user. Pursuant to Part 15 of the Federal

Communications Commission (FCC) Rules, the user is cautioned that

changes or modifications not expressly approved by Avaya Inc. could

void the user's authority to operate this equipment.

How to Get Help

For additional support telephone numbers, go to the Avaya support Web

site: http://www.avaya.com/support

. If you are:

• Within the United States, click the Escalation Contacts link

that is located under the Support Tools heading. Then click

the appropriate link for the type of support that you need.

• Outside the United States, click the Escalation Contacts link

that is located under the Support Tools heading. Then click

the International Services link that includes telephone

numbers for the international Centers of Excellence.

Product Safety Standards

This product complies with and conforms to the following international

Product Safety standards as applicable:

• Safety of Information Technology Equipment, IEC 60950-1,

1st Edition, including all relevant national deviations as listed

in Compliance with IEC for Electrical Equipment (IECEE)

CB-96A.

• Safety of Information Technology Equipment, CAN/

CSA-C22.2 No. 60950-1-03 / UL 60950-1, 1st Edition.

• Safety Requirements for Information Technology Equipment,

AS/NZS 60950:2000.

• One or more of the following Mexican national standards, as

applicable: NOM 001 SCFI 1993, NOM SCFI 016 1993, NOM

019 SCFI 1998

This product may also comply with and conform to other national,

regional or commonly recognized product safety standards. For

information regarding specific standards, check the product label or

contact your local Avaya representative.

Electromagnetic Compatibility (EMC) Standards

This product complies with and conforms to the following international

EMC standards and all relevant national deviations:

• Limits and Methods of Measurement of Radio Interference of

Information Technology Equipment, CISPR 22:1997,

EN55022:1998, and AS/NZS 3548.

• Information Technology Equipment - Immunity

Characteristics - Limits and Methods of Measurement,

CISPR 24:1997 and EN55024:1998, including:

• Electrostatic Discharge (ESD) IEC 61000-4-2

• Radiated Immunity IEC 61000-4-3

• Electrical Fast Transient IEC 61000-4-4

• Surge Immunity IEC 61000-4-5

• Conducted Immunity IEC 61000-4-6

• Power Frequency H-Field Immunity IEC 61000-4-8

• Voltage Dips & Variations Immunity IEC 61000-4-11

Federal Communications Commission Statement, Part 15:

This device complies with Part 15 of the FCC Rules. Operation is subject

to the following two conditions: (1) this device may not cause harmful

interference, and (2) this device must accept any interference received,

including interference that may cause undesired operation.

USA FCC CFR 47 part 15

Federal Communication Commission (FCC) Radio Frequency Devices,

Sub part B Unintentional Radiators: Sections 15.107 & 15.109. Class B

Device Declaration / User Statement Note:

This equipment has been tested and found to comply with the limits for a

Class B digital device, pursuant to Part 15 of the FCC rules. These limits

are designed to provide reasonable protection against harmful

interference in a residential installation. This equipment generates,

uses, and can radiate radio frequency energy and, if not installed and

used in accordance with the instructions, may cause harmful interference

to radio communications. However, there is no guarantee that

interference will not occur in a particular installation. If this equipment

does cause interference to radio or television reception, which can be

determined by turning the equipment off and on, the user is encouraged

to try to correct the interference by one or more of the following

measures.

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different

from that to which the receiver is connected.

• Consult the dealer or an experienced radio / TV technician for

help.

Declaration of Conformity (DoC) statement is available on the Avaya

external web site: http://support.avaya.com/elmodocs2/DoC/

Reference Power Supplies.

European Union Declarations of Conformity

Avaya Inc. declares that the equipment specified in this

document bearing the “CE” (Conformité Europeénne)

mark conforms to the European Union Radio and

Telecommunications Terminal Equipment Directive (1999/

5/EC), including the Electromagnetic Compatibility Directive (89/336/

EEC) and Low Voltage Directive (73/23/EEC).

Copies of these Declarations of Conformity (DoCs) can be obtained by

contacting your local sales representative and are available on the

following Web site: http://www.avaya.com/support

Japan

This is a Class B product based on the standard of the Voluntary Control

Council for Interference by Information Technology Equipment (VCCI). If

this equipment is used in a domestic environment, radio disturbance may

occur, in which case, the user may be required to take corrective actions.

Other

The above statements of compliance and conformity to various product

safety and EMC standards may not be complete, and are subject to

change. Changes may occur as certifications, listings, approvals, etc. are

obtained or removed in accordance with various national and/or regional

requirements. Applicable certification, listing, agency, and other such

symbols and/or marks are often required to be visible on the product and

may in many cases be used as a visual indication that the product has

been tested and approved under the requirements of the associated

country, organization, agency, certification body, etc. Checking the power

supply markings is a good first step in determining which agency

approvals have been granted. For inquiries regarding specific

certifications, contact your local or regional Avaya representative.

To order copies of this and other documents:

Call: Avaya Publications Center

Voice 1.800.457.1235 or 1.207.866.6701

FAX 1.800.457.1764 or 1.207.626.7269

Write: Globalware Solutions

200 Ward Hill Avenue

Haverhill, MA 01835 USA

Attention: Avaya Account Management

E-mail: [email protected]

For the most current versions of documentation, go to the Avaya support

Web site: http://www.avaya.com/support

Sources of Information

For information about an 1151C1 or 1151C2 power supply or instructions

on how to install it, refer to this instruction booklet packed with the

product. Additional installation information may often be found in the user

or installation manual of the terminal or adjunct equipment used with the

power supply. As the 1151C1 and 1151C2 are third generation power

supplies, the original product manuals may describe use with the prior

generation 1151A1/A2 or 1151B1/B2 models. The models 1151C1 and

1151C2 are direct replacements for these legacy Avaya and Lucent

models and may be substituted for them. (Please note that although the

physical appearance of the power supplies have changed, the basic

functionality has remained the same.)

Power Supply Description

The 1151C1 power supply is a “desktop”, single output 48 volt dc, 20 watt

power supply. The power supply can operate over a wide range of AC

input voltage and frequency: 90 - 264 VAC, 47-63 Hz.

The 1151C2 power supply is a “desktop “, single output 48 volt dc, 20

watt power supply with battery holdover. The power supply can operate

over a wide range of AC input voltage and frequency: 90 - 264 VAC, 47

63 Hz. When AC power fails the battery (if fully charged) should provide

approximately 15 minutes of holdover at full load (20 watts) or about 8

hours at light load (2 watts). As many factors may impact battery

performance (such as level of charge, age of the battery, temperature,

etc.), actual performance will vary.

The 1151C1/C2 Power Supplies

The 1151C1/C2 Power Supplies can be used to supply local power to the

following Lucent or Avaya products:

• Adjunct equipment such as the EU24, EU24BL (when

attached to a compatible DCP telephone);

• DCP compatible Expansion Modules such as the XM24, 1EM

or 2EM, and other optional equipment including the 100A

Analog Interface Module, 20A Stand with 200A Analog

Adjunct Interface and/or 201A Recorder Interface Modules

installed on DCP phones;

• DCP Voice Terminal Series 64xx, 74xx and 84xx when

needed for powering optional adjuncts, or where required as

for the model 8411;

• DCP 7444 and 8434 voice terminals which need auxiliary

power for their vacuum fluorescent displays;

• Adjunct equipment such as the S201A and CS201A

speakerphones or a 500A Headset Adapter attached to any

Analog, DCP, or ISDN-T voice terminal equipped with an

Adjunct jack;

• MLX-20L™, MLX-20LS™, MLX-28D™, MLX-28DS™

telephones connected to a Lucent or Avaya MERLIN

LEGEND

Communications System;

• MLS-CA24 Call Assistant™ Intercom Autodialer (DSS) and

the Remote Access Unit connected to a Lucent or Avaya

PARTNER

Communications System;

• ISDN-T 65xx, 75xx, and 85xx series voice terminal

connected to a Lucent or Avaya DEFINITY

Communications

System.

Note: Failure to use and install as directed could result in injury. No other

use of the 1151C1/C2 Power supplies is recommended or warranted. At

the time of publication, every effort has been made to insure accuracy of

this manual. However, it is possible that 1) some omissions have

occurred, or 2) new products have since been introduced that use the

1151C1 or 1151C2 power supply. If you are unsure concerning the

suitability of models 1151C1 or 1151C2 for a particular application, check

your product documentation or contact your local Avaya representative

for assistance.

CAUTION:

The 1151C1 and 1151C2 Power Supplies can only be used with

telecommunications equipment, indoors, in a controlled environment.

Operation

The maximum loop range between the telephone and the power supply

is 14 feet.

This power supply is intended to replace the MSP-1, 329A, 353A,

1151A1/A2 and the 1151B1/B2 DC power supplies, the Definity Adjunct

Power Kit (consisting of the KS-22911-L1/2 Plug-In Power Supply,

D6AP-87 cord and 400B2 adapter), and the 2012D AC transformer.

The 1151C1 power unit has a green LED that shows the unit has power

on the PHONE jack, pins 7 & 8 when AC power is applied.

The 1151C2 power unit has two LED's: a green LED that shows the unit

has power on the PHONE jack, pins 7 & 8 when AC power is applied or

running on battery and a YELLOW LED that shows the unit is charging

the battery when illuminated. When blinking, the GREEN LED indicates

that the unit is running on battery power.

The 1151C2 incorporates a new integrated feature that allows one to

easily disable the output when the supply is disconnected from AC mains

power. This allows storage of the power supply without rapid discharging

of the internal sealed Lead-acid battery due to continued operation of the

internal battery-voltage to output-voltage converter (henceforth referred

to as the “boost converter”). After disconnecting the 1151C2 power

supply from the AC mains following 1) normal use, or 2) periodic

recharge maintenance of the internal battery, the user should do the

following:

• Locate the disable-switch access hole on the base of the

1151C2 power supply. Insert a fine non-metallic object (such

as a wooden or plastic toothpick) into the access hole and

depress the recessed momentary contact switch. This

operation disables the internal boost converter. Once the

boost converter is disabled, all status LEDs will turn off (this

may take a few seconds as the stored charge in the output

filter capacitors is discharged). This operation should only be

done when the power supply is to be stored or is to go

through a period of non-use.

Note: One should not press the disable button when the supply is in

active operation during a power failure. Once the boost converter disable

button is pressed, the supply will no longer function until AC mains power

is restored. When AC mains power is restored to the power supply,

normal operation will resume.

Maintenance

The Avaya models 1151C1/C2 power supplies contain no user

serviceable parts. To reduce the risk of electric shock, do not

disassemble the product.

To clean the 1151C1/C2 power supply, first unplug the AC power cord

from the wall receptacle (or other AC source) and disconnect all cords

from the Line and Phone RJ45 jacks. Do not use liquid cleaners or

aerosol cleaners. Use a damp cloth for cleaning.

Like all batteries, the internal Lead-acid battery of the 1151C2 power

supply will self-discharge over a period of inactivity and must be

periodically recharged to avoid damage. This is not a concern during

normal supply operation, as the power supply will automatically recharge

as needed. However, when stored and disconnected from the AC mains

for an extended period of time, the battery should be recharged every six

months to prolong battery life and avoid damage resulting from deep

discharge. This may be done by simply connecting the power supply to a

source of AC power and allowing the battery to charge for at least twelve

hours. When battery charging is complete, if the power supply is to be

placed back into storage or disconnected again from the AC mains, one

should immediately disable the battery boost converter as outlined in the

“Operation” section above.

Contents of the 1151C1 and 1151C2 Boxes

*If a longer network cable is desired, a 4.26m (14 ft) Cat5e patch cable is

available for purchase from Avaya using comcode: 700204050.

Connecting the Power Supply

The power output is provided through a modular jack on the power

supply. These jacks are labeled as follows:

The supply output is essentially isolated from earth ground and

depending on the particular application, either output pin may be used to

establish a reference potential. However, it is common in

telecommunications applications to think of the supply output as nominal

-48Vdc (pin 7) relative to a 0Vdc reference on pin 8.

The output jack, labeled “IP/DCP PHONE” is an 8-pin female non-keyed

RJ45 jack that can accept D8W and RJ45 modular plug cables.

The input jack, labeled “LAN/DCP” is an 8-pin female non-keyed RJ45

jack that can accept RJ45 modular plug cables, such as Cat5 (LAN) or

Cat3 (DCP line) cables. A Cat5e cable fitted with RJ45 modular plugs is

provided with the supply and may often be used in place of a D8W type

cable if desired.

1151C1

Quantity Comcode

1 1151C1 Power Supply 700356447

1 1.9 m (6.23 ft) Cat5 Network Cable*

1 Installation & Safety Instructions

1151C2

Quantity Comcode

1 1151C2 Power Supply 700356454

1 1.9 m (6.23 ft) Cat5 Network Cable*

1 Installation & Safety Instructions

IP/DCP

PHONE LAN/PBX

The following local powering arrangements, shown in Figures 1 - 4, can

be used with the 1151C1/C2 Power Supplies:

• Figure 1 shows the local powering arrangement for the

model 7444 voice terminal, and for models 2420, 6416, 6424

and CALLMASTER

telephones when used with an adjunct.

This arrangement is also used for the 302D attendant

consoles. This arrangement can also be used on legacy

terminals where the 1151A or 1151B were recommended.

• Figure 2 shows the local powering arrangement for MERLIN

LEGEND telephones.

• Figure 3 shows the local powering arrangement for a

PARTNER MLS-CA24 DSS.

• Figure 4 shows the local powering arrangement for a

PARTNER Remote Access Unit.

Note: The type of cord(s) needed to make these connections are

designated in each drawing.

Trademarks

CALLMASTER, DEFINITY, MERLIN, MERLIN LEGEND, and PARTNER

are registered trademarks of Avaya Inc. MLX-20L, MLX-20LS, MLX-28D,

and MLX-28DS are trademarks of Avaya in the U.S. and other countries.

Avaya Limited Warranty

What is covered: Any defect in materials or workmanship.

For how Long: One year.

What will we do: If your Avaya product is defective in material and

workmanship and is returned within one year of date it was purchased,

we will repair it or, at our option, replace it at no charge to you.

What we ask you to do: To get warranty service for Avaya product, you

must provide proof of the date of purchase.

Figure 1: Local Powering Arrangement for Model 7444, and for 2420, 6416, 6424 and CALLMASTER

Telephones when Used with an Adjunct

Figure 2: Local Powering Arrangement for MERLIN LEGEND

Telephones

Figure 3: Local Powering Arrangement for a PARTNER

MLS-CA24 DSS

Figure 4: Local Powering Arrangement for a PARTNER

Remote Access Unit

Avaya 1151C1/1151C2 User manual

Brand: Avaya

Model: 1151C1/1151C2

Type: User manual

Download PDF

report

in other languages

italiano: Avaya 1151C1/1151C2 Manuale utente
français: Avaya 1151C1/1151C2 Manuel utilisateur
español: Avaya 1151C1/1151C2 Manual de usuario
Deutsch: Avaya 1151C1/1151C2 Benutzerhandbuch
русский: Avaya 1151C1/1151C2 Руководство пользователя
Nederlands: Avaya 1151C1/1151C2 Handleiding
português: Avaya 1151C1/1151C2 Manual do usuário
dansk: Avaya 1151C1/1151C2 Brugermanual
polski: Avaya 1151C1/1151C2 Instrukcja obsługi
čeština: Avaya 1151C1/1151C2 Uživatelský manuál
svenska: Avaya 1151C1/1151C2 Användarmanual
suomi: Avaya 1151C1/1151C2 Ohjekirja

Avaya 1151C1/1151C2 User manual

Avaya 1151C1/1151C2 User manual

in other languages

Related papers

Other documents