Genius BRAIN 06 Operating instructions

Brand: Genius

Model: BRAIN 06

Type: Operating instructions

Page is loading ...

AVVERTENZE PER L’INSTALLATORE

OBBLIGHI GENERALI PER LA SICUREZZA

1) ATTENZIONE! È importante per la sicurezza delle persone seguire attentamente tutta

l’istruzione. Una errata installazione o un errato uso del prodotto può portare a

gravi danni alle persone.

2) Leggere attentamente le istruzioni prima di iniziare l’installazione del prodotto.

3) I materiali dell’imballaggio (plastica, polistirolo, ecc.) non devono essere lasciati

alla portata dei bambini in quanto potenziali fonti di pericolo.

4) Conservare le istruzioni per riferimenti futuri.

5) Questo prodotto è stato progettato e costruito esclusivamente per l’utilizzo indi-

cato in questa documentazione. Qualsiasi altro utilizzo non espressamente indi-

cato potrebbe pregiudicare l’integrità del prodotto e/o rappresentare fonte di

pericolo.

6) GENIUS declina qualsiasi responsabilità derivata dall’uso improprio o diverso da

quello per cui l’automatismo è destinato.

7) Non installare l’apparecchio in atmosfera esplosiva: la presenza di gas o fumi in-

fiammabili costituisce un grave pericolo per la sicurezza.

8) Gli elementi costruttivi meccanici devono essere in accordo con quanto stabilito

dalle Norme EN 12604 e EN 12605.

Per i Paesi extra-CEE, oltre ai riferimenti normativi nazionali, per ottenere un livello di

sicurezza adeguato, devono essere seguite le Norme sopra riportate.

9) GENIUS non è responsabile dell’inosservanza della Buona Tecnica nella costruzione

delle chiusure da motorizzare, nonché delle deformazioni che dovessero interve-

nire nell’utilizzo.

10) L’installazione deve essere effettuata nell’osservanza delle Norme EN 12453 e EN

12445. Il livello di sicurezza dell’automazione deve essere C+D.

11) Prima di effettuare qualsiasi intervento sull’impianto, togliere l’alimentazione elet-

trica e scollegare le batterie.

12) Prevedere sulla rete di alimentazione dell’automazione un interruttore onnipolare

con distanza d’apertura dei contatti uguale o superiore a 3 mm. È consigliabile

l’uso di un magnetotermico da 6A con interruzione onnipolare.

13) Verificare che a monte dell’impianto vi sia un interruttore differenziale con soglia

da 0,03 A.

14) Verificare che l’impianto di terra sia realizzato a regola d’arte e collegarvi le parti

metalliche della chiusura.

15) L’automazione dispone di una sicurezza intrinseca antischiacciamento costituita

da un controllo di coppia. E’ comunque necessario verificarne la sogli di interven-

to secondo quanto previsto dalle Norme indicate al punto 10.

16) I dispositivi di sicurezza (norma EN 12978) permettono di proteggere eventuali

aree di pericolo da Rischi meccanici di movimento, come ad Es. schiacciamento,

convogliamento, cesoiamento.

17) Per ogni impianto è consigliato l’utilizzo di almeno una segnalazione luminosa

nonché di un cartello di segnalazione fissato adeguatamente sulla struttura del-

l’infisso, oltre ai dispositivi citati al punto “16”.

18) GENIUS declina ogni responsabilità ai fini della sicurezza e del buon funzionamen-

to dell’automazione, in caso vengano utilizzati componenti dell’impianto non di

produzione GENIUS.

19) Per la manutenzione utilizzare esclusivamente parti originali GENIUS.

20) Non eseguire alcuna modifica sui componenti facenti parte del sistema d’auto-

mazione.

21) L’installatore deve fornire tutte le informazioni relative al funzionamento manuale

del sistema in caso di emergenza e consegnare all’Utente utilizzatore dell’impian-

to il libretto d’avvertenze allegato al prodotto.

22) Non permettere ai bambini o persone di sostare nelle vicinanze del prodotto du-

rante il funzionamento.

23) Tenere fuori dalla portata dei bambini radiocomandi o qualsiasi altro datore di im-

pulso, per evitare che l’automazione possa essere azionata involontariamente.

24) Il transito tra le ante deve avvenire solo a cancello completamente aperto.

25) L’Utente utilizzatore deve astenersi da qualsiasi tentativo di riparazione o d’inter-

vento diretto e rivolgersi solo a personale qualificato.

26) Tutto quello che non è previsto espressamente in queste istruzioni non è permes-

IMPORTANT NOTICE FOR THE INSTALLER

GENERAL SAFETY REGULATIONS

1) ATTENTION! To ensure the safety of people, it is important that you read all the

following instructions. Incorrect installation or incorrect use of the product could

cause serious harm to people.

2) Carefully read the instructions before beginning to install the product.

3) Do not leave packing materials (plastic, polystyrene, etc.) within reach of chil-

dren as such materials are potential sources of danger.

4) Store these instructions for future reference.

5) This product was designed and built strictly for the use indicated in this documen-

tation. Any other use, not expressly indicated here, could compromise the good

condition/operation of the product and/or be a source of danger.

6) GENIUS declines all liability caused by improper use or use other than that for which

the automated system was intended.

7) Do not install the equipment in an explosive atmosphere: the presence of inflam-

mable gas or fumes is a serious danger to safety.

8) The mechanical parts must conform to the provisions of Standards EN 12604 and

EN 12605.

For non-EU countries, to obtain an adequate level of safety, the Standards mentioned

above must be observed, in addition to national legal regulations.

9) GENIUS is not responsible for failure to observe Good Technique in the construction

of the closing elements to be motorised, or for any deformation that may occur

during use.

10) The installation must conform to Standards EN 12453 and EN 12445. The safety level

of the automated system must be C+D.

11) Before attempting any job on the system, cut out electrical power and discon-

nect the batteries.

12) The mains power supply of the automated system must be fitted with an all-pole

switch with contact opening distance of 3mm or greater. Use of a 6A thermal

breaker with all-pole circuit break is recommended.

13) Make sure that a differential switch with threshold of 0.03 A is fitted upstream of

the system.

14) Make sure that the earthing system is perfectly constructed, and connect metal

parts of the means of the closure to it.

15) The automated system is supplied with an intrinsic anti-crushing safety device con-

sisting of a torque control. Nevertheless, its tripping threshold must be checked as

specified in the Standards indicated at point 10.

16) The safety devices (EN 12978 standard) protect any danger areas against mecha-

nical movement Risks, such as crushing, dragging, and shearing.

17) Use of at least one indicator-light is recommended for every system, as well as a

warning sign adequately secured to the frame structure, in addition to the devi-

ces mentioned at point “16”.

18) GENIUS declines all liability as concerns safety and efficient operation of the auto-

mated system, if system components not produced by GENIUS are used.

19) For maintenance, strictly use original parts by GENIUS.

20) Do not in any way modify the components of the automated system.

21) The installer shall supply all information concerning manual operation of the sy-

stem in case of an emergency, and shall hand over to the user the warnings han-

dbook supplied with the product.

22) Do not allow children or adults to stay near the product while it is operating.

23) Keep remote controls or other pulse generators away from children, to prevent the

automated system from being activated involuntarily.

24) Transit through the leaves is allowed only when the gate is fully open.

25) The user must not attempt any kind of repair or direct action whatever and con-

tact qualified personnel only.

26) Anything not expressly specified in these instructions is not permitted.

CONSIGNES POUR L’INSTALLATEUR

RÈGLES DE SÉCURITÉ

1) ATTENTION! Il est important, pour la sécurité des personnes, de suivre à la lettre

toutes les instructions. Une installation erronée ou un usage erroné du produit peut

entraîner de graves conséquences pour les personnes.

2) Lire attentivement les instructions avant d’installer le produit.

3) Les matériaux d’emballage (matière plastique, polystyrène, etc.) ne doivent pas

être laissés à la portée des enfants car ils constituent des sources potentielles de

danger.

4) Conserver les instructions pour les références futures.

5) Ce produit a été conçu et construit exclusivement pour l’usage indiqué dans cette

documentation. Toute autre utilisation non expressément indiquée pourrait com-

promettre l’intégrité du produit et/ou représenter une source de danger.

6) GENIUS décline toute responsabilité qui dériverait d’usage impropre ou différent de

celui auquel l’automatisme est destiné.

7) Ne pas installer l’appareil dans une atmosphère explosive: la présence de gaz ou

de fumées inflammables constitue un grave danger pour la sécurité.

8) Les composants mécaniques doivent répondre aux prescriptions des Normes EN

12604 et EN 12605.

Pour les Pays extra-CEE, l’obtention d’un niveau de sécurité approprié exige non seu-

lement le respect des normes nationales, mais également le respect des Normes

susmentionnées.

9) GENIUS n’est pas responsable du non-respect de la Bonne Technique dans la con-

struction des fermetures à motoriser, ni des déformations qui pourraient intervenir

lors de l’utilisation.

10) L’installation doit être effectuée conformément aux Normes EN 12453 et EN 12445.

Le niveau de sécurité de l’automatisme doit être C+D.

11) Couper l’alimentation électrique et déconnecter la batterie avant toute inter-

vention sur l’installation.

12) Prévoir, sur le secteur d’alimentation de l’automatisme, un interrupteur omnipo-

laire avec une distance d’ouverture des contacts égale ou supérieure à 3 mm.

On recommande d’utiliser un magnétothermique de 6A avec interruption om-

nipolaire.

13) Vérifier qu’il y ait, en amont de l’installation, un interrupteur différentiel avec un

seuil de 0,03 A.

14) Vérifier que la mise à terre est réalisée selon les règles de l’art et y connecter les

pièces métalliques de la fermeture.

15) L’automatisme dispose d’une sécurité intrinsèque anti-écrasement, formée d’un

contrôle du couple. Il est toutefois nécessaire d’en vérifier le seuil d’intervention

suivant les prescriptions des Normes indiquées au point 10.

16) Les dispositifs de sécurité (norme EN 12978) permettent de protéger des zones

éventuellement dangereuses contre les Risques mécaniques du mouvement,

comme l’écrasement, l’acheminement, le cisaillement.

17) On recommande que toute installation soit doté au moins d’une signalisation lu-

mineuse, d’un panneau de signalisation fixé, de manière appropriée, sur la struc-

ture de la fermeture, ainsi que des dispositifs cités au point “16”.

18) GENIUS décline toute responsabilité quant à la sécurité et au bon fonctionnement

de l’automatisme si les composants utilisés dans l’installation n’appartiennent pas

à la production GENIUS.

19) Utiliser exclusivement, pour l’entretien, des pièces GENIUS originales.

20) Ne jamais modifier les composants faisant partie du système d’automatisme.

21) L’installateur doit fournir toutes les informations relatives au fonctionnement ma-

nuel du système en cas d’urgence et remettre à l’Usager qui utilise l’installation les

“Instructions pour l’Usager” fournies avec le produit.

22) Interdire aux enfants ou aux tiers de stationner près du produit durant le fonction-

nement.

23) Eloigner de la portée des enfants les radiocommandes ou tout autre générateur

d’impulsions, pour éviter tout actionnement involontaire de l’automatisme.

24) Le transit entre les vantaux ne doit avoir lieu que lorsque le portail est complète-

ment ouvert.

25) L’Usager qui utilise l’installation doit éviter toute tentative de réparation ou d’inter-

vention directe et s’adresser uniquement à un personnel qualifié.

26) Tout ce qui n’est pas prévu expressément dans ces instructions est interdit.

ADVERTENCIAS PARA EL INSTALADOR

REGLAS GENERALES PARA LA SEGURIDAD

1) ATENCION! Es sumamente importante para la seguridad de las personas seguir

atentamente las presentes instrucciones. Una instalación incorrecta o un uso im-

propio del producto puede causar graves daños a las personas.

2) Lean detenidamente las instrucciones antes de instalar el producto.

3) Los materiales del embalaje (plástico, poliestireno, etc.) no deben dejarse al alcan-

ce de los niños, ya que constituyen fuentes potenciales de peligro.

4) Guarden las instrucciones para futuras consultas.

5) Este producto ha sido proyectado y fabricado exclusivamente para la utilización

indicada en el presente manual. Cualquier uso diverso del previsto podría perju-

Page is loading ...

ENGLISH

WARNINGS

• Important! For the safety of people, it is important that all the instructions be carefully observed.

• Incorrect installation or incorrect use of the product could cause serious harm to people.

• Carefully read the instructions before beginning to install the product and keep them for future

reference.

• The symbol indicates notes that are important for the safety of persons and for the good condition

of the automated system.

• The symbol draws your attention to the notes on the characteristics and operation of the

product.

CE DECLARATION OF CONFORMITY

Manufacturer: GENIUS S.p.A.

Address: Pdre Elzi, 32 - 24050 - Grassobbio - Bregamo - ITALY

Declares that: Control board mod. BRAIN 06,

• conforms to the essential safety requirements of the following EEC directives:

73/23/EEC and subsequent amendment 93/68/EEC.

89/336/EEC and subsequent amendment 92/31/EEC and 93/68/EEC

Additional information:

This product underwent a test in a typical, uniform configuration.

(all products made by GENIUS S.p.A)

Grassobbio 01 July 2006. The Managing Director

D. Gianantoni

1 WARNINGS ....................................................................................................................................................... 10

2 LAYOUT AND CONNECTIONS ........................................................................................................................... 10

3 TECHNICAL SPECIFICATIONS ........................................................................................................................... 11

3.1 DESCRIPTION OF COMPONENTS ....................................................................................................................................11

3.2 DESCRIPTION OF TERMINAL-BOARDS ..............................................................................................................................11

4 PROGRAMMING THE LOGIC ............................................................................................................................. 11

5 PROGRAMMING THE SPEED .............................................................................................................................. 11

6. START-UP .......................................................................................................................................................... 12

6.1 LEDS CHECK ..................................................................................................................................................................12

6.2 PROGRAMMING THE DIPS-SWITCH .................................................................................................................................12

6.3 PRE-FLASHING ..............................................................................................................................................................12

6.4 TIME - SETUP LEARNING .................................................................................................................................................12

6.4.1 AUTOMATIC SET-UP ......................................................................................................................................................................... 12

6.4.2 MANUAL SET-UP .............................................................................................................................................................................. 12

7 INSTALLATION OF BUS ACCESSORIES ............................................................................................................... 13

7.1 ADDRESSING THE BUS PHOTOCELLS...............................................................................................................................13

7.2 MEMORY STORAGE OF BUS ACCESSORIES ...................................................................................................................14

8 MEMORY STORING THE RADIO CODE ............................................................................................................... 14

8.1 MEMORY STORAGE OF AMIGO RADIO CONTROLS ........................................................................................................14

8.2 MEMORY STORAGE OF BRAVO RADIO CONTROLS (for some markets only) .................................................................15

8.2.1 REMOTE MEMORY STORAGE OF BRAVO RADIO CONTROLS ............................................................................................................ 15

8.3 RADIO CONTROLS DELETION PROCEDURE .....................................................................................................................15

9 CONNECTION OF BUFFER BATTERIES (OPTIONAL) ............................................................................................. 15

10 AUTOMATED SYSTEM TEST ................................................................................................................................ 15

11 LOGIC TABLES .................................................................................................................................................. 16

INDEX

Fig. 1

ENGLISH

1 WARNINGS

Before attempting any work on the control unit (connections, maintenance), always turn off power.

- Install, upstream of the system, a differential thermal breaker with adequate tripping threshold,

- Always separate power cables from control and safety cables (push-button, receiver, photocells, etc.).

To avoid any electrical disturbance, use separate sheaths or a screened cable (with the screen earthed).

CONTROL UNIT BRAIN 06

2 LAYOUT AND CONNECTIONS

(PARTIAL OPENING)

(TOTAL OPENING)

ENGLISH

3 TECHNICAL SPECIFICATIONS

Power supply voltage

230Vac (+6% -10%) - 50Hz

Absorbed power

20W

Motor max. load

150W x 2

Accessories max. current (+24V)

100 mA

BUS Accessories max.current

400 mA

Operating ambient temperature

-20°C - +55°C

Fuses

F1 = self-resetting; F2 = T2A-

250V

Function logics

EP, AP

Work time (time-out)

1 minute (fixed)

Pause time

Varies according to learning

(max. 10 min.)

Terminal board inputs

Open A, Open B, Stop, BUS

(I/O)

Connector inputs

Power supply, battery

radio module

Terminal board outputs

Motors, flashing lamp, power

supply to accessories,

electric lock, service light

contact (90 sec fixed)

Programmable functions

Logic (AP, EP), Speed (high

13°/sec and low 10°/sec)

Learning functions

Pause time, leaf 2 delay at

closing

Integrated radio channels type

433 MHz / 868MHZ

(max 250 channels)

J1 POWER SUPPLY connector

SERVICE LIGHT command terminal-board

J3 FLASHING LAMP terminal-board

J4 ELECTRIC LOCK terminal-board

J5 COMMANDS terminal-board

J7 MOTOR 1 terminal-board

J8 MOTOR 2 terminal-board

J9 Rapid connection for RADIO MODULE

J10 BUS terminal-board

J11 BATTERY connector

SW1 SET UP push-button

SW2 SPEED push-button

SW3 LOGIC push-button

DS1 Programming Dip-switch

F1 Accessories protective fuse

F2 Fuses protecting transformers and motors

LED Signalling LEDs

3.1 DESCRIPTION OF COMPONENTS

Terminal and/or

terminal-board

Description Device connected

+24V

Power supply for

accessories

2 GND Negative

3 STOP

Device with NC

contact which causes

the automated

system to shut down

4 OPEN B

Device with N.O

contact (see chap.

FUNCTION LOGICS)

5 OPEN A

J10

RED terminal

BUS

Safety devices with

BUS technology

GREY terminal

SERVICE

LIGHT

Service Light control

output (connect a

relay coil at 24Vdc-

100mA max)

ORANGE terminal

LAMP

Flashing lamp 24Vdc

- 15W

BLUE terminal

LOCK

Electric lock 12Vac or

24 Vdc (to be installed

on leaf 1)

J7 MOT1 Motor 1 (leaf 1)

J8 MOT2 Motor 2 (leaf 2)

3.2 DESCRIPTION OF TERMINAL-BOARDS

4 PROGRAMMING THE LOGIC

The function logic can be selected at any time by pressing

push-button SW3.

The selected logic is then displayed on LED LD7:

LED on = AUTOMATIC STEPPED logic (AP)

LED off = SEMIAUTOMATIC STEPPED logic (EP)

5 PROGRAMMING THE SPEED

The function logic can be adjusted at any time by pressing

push-button SW2.

The selected logic is then displayed on LED LD8:

LED on = HIGH speed (13 °/sec)

LED off = LOW speed (10 °/sec)

Leaf 1 means the leaf which opens first during

the opening operation.

The service light control is active during the

entire gate opening or closing movement and

for the successive 90 seconds.

ENGLISH

6.4 TIME - SETUP LEARNING

Before any manoeuvre is executed, a SETUP

cycle must first be run.

During SETUP do not interrupt the photocells

because their interruption causes the immedi-

ate stop of the leaves. To end the procedure,

repeat SETUP from the beginning.

When the board is powered up and a SETUP cycle has never

been executed, LEDs LD4 and LD5 begin to flash slowly to signal

that a SETUP cycle must be executed.

There are two possible types of SETUP: AUTOMATIC and

MANUAL

6.4.1 AUTOMATIC SET-UP

To execute an AUTOMATIC SETUP, follow the procedure below:

Take the leaves to mid-point.

Hold down the SETUP (SW1) push-button until the 2 adjacent

LEDs (LD4 and LD5) light up on steady beam.

Release the SETUP push-button, LEDs LD4 and LD5 begin

to flash rapidly.

Leaf 2 (if present) starts the closing movement, stopping

when it reaches the closing mechanical stop

Leaf 1 starts the closing movement, stopping when it

reaches the closing mechanical stop

Leaf 1 starts the opening movement.

Leaf 2 (if present) starts the opening movement after a

fixed delay at opening.

Leaves 1 and 2 (if present) stop when they reach the

opening mechanical stop.

Wait for LEDs LD4 and LD5 to go OFF, which means that the

SETUP procedure has finished.

Give an OPEN pulse to close the gate

When the SETUP procedure has been started,

if the leaves at point 4 and 5 open instead of

closing, the motor power supply cables must

be changed over.

When using the AUTOMATIC SETUP, the slow

down spaces, the leaf opening and closing

delays, and the pause time (30 sec., with AP

logic), are all preset by the board and cannot

be modified.

10.

LED ON (closed contact) OFF (open contact)

STOP Command disabled Command enabled

OPEN A Command enabled Command disabled

OPEN B Command enabled Command disabled

BUS See par. 7.2

6. START-UP

6.1 LEDS CHECK

The following table shows that status of the LEDs in relation to

the status of the inputs (the closed at rest automated system

condition is shown in bold).

Check the status of the signalling LEDs as per table below:

Tab.1 – Operation of inputs status LEDs

6.4.2 MANUAL SET-UP

To execute a MANUAL SETUP, follow the procedure below:

Take the leaves to mid-point.

Hold down the SETUP (SW1) push-button until the leaves

start to move.

Release the SETUP push-button, LEDs LD4 and LD5 begin

to flash rapidly

Leaf 2 (if present) starts the closing movement, stopping

when it reaches the closing mechanical stop

Leaf 1 starts the closing movement, stopping when it rea-

ches the closing mechanical stop

Leaf 1 starts the opening movement.

Leaf 2 (if present) starts the opening movement after a

fixed delay at opening.

Leaves 1 and 2 (if present) stop when they reach the ope-

ning mechanical stop.

If LOW force was set, wait for about 5 sec checking if the

flashing lamp goes OFF.

6.2 PROGRAMMING THE DIPS-SWITCH

DS1 DS2 DS3 DS4 Description

OFF OFF LOW FORCE

OFF ON MEDIUM - LOW FORCE

ON OFF MEDIUM - HIGH FORCE

ON ON HIGH FORCE

ON ANTI-WIND ON

OFF ANTI-WIND OFF

ON REVERSING STROKE ON

OFF REVERSING STROKE OFF

If you connect an electric lock to terminal J4,

position DS4 to ON to enable the reversing stro-

ke (before opening, the motors thrust to close,

thus facilitating the electric lock to uncouple).

By setting dip-switch DS3 on ON, a specialBy setting dip-switch DS3 on ON, a special

antiwind function is activated that enables the

gate operation even if strong wind is present.

The following tables show the settings of the DS1 dip-switch for

programming force, pre-flashing and reversing stroke.

Tab. 2 - DS1 programming (default settings in bold)

6.3 PRE-FLASHING

The pre-flashing function can be activated and disabled (fol-

lowing an OPEN command, the unit activates the flashing lamp

for 3 seconds before it starts the movement). Procedure:

Press LOGIC key (SW3) for at least 5 secs. to ACTIVATE

pre-flashing.

Press SPEED key (SW2) for at least 5 secs. to DESACTIVATE

pre-flashing.

In both cases check if the LED of the pressed key

changes its status: in such cases it means that

the function of the key and not the pre-flashing

was changed.

Fig. 2

ENGLISH

7 INSTALLATION OF BUS ACCESSORIES

This board is supplied with a BUS circuit enabling easy con-

nection of a high number of BUS accessories (e.g. up to 16

photocells pairs), appropriately programmed, using only two

cable without polarity.

Below we describe the addressing and memory storage of

the BUS photocells.

For other future accessories, refer to the specific instructions.

7.1 ADDRESSING THE BUS PHOTOCELLS

Important: the same address must be given to

both transmitter and receiver.

Make sure that there are no two or more

photocells pairs with the same address.

If no BUS accessory is used, leave the BUS con-

nector free (J10 - fig. 1).

A maximum of 16 BUS photocell pairs can be connected to

the board.

The photocells are split into groups:

Opening photocells: max 6

Closing photocells: max 7

Opening /Closing photocells: max 2

Photocell used as an OPEN pulse: max 1

Dip1 Dip2 Dip3 Dip4 Ref. Type

OFF OFF OFF OFF

B -C OPENING

OFF OFF OFF ON

OFF OFF ON OFF

OFF OFF ON ON

OFF ON ON OFF

OFF ON ON ON

ON OFF OFF OFF

D CLOSING

ON OFF OFF ON

ON OFF ON OFF

ON OFF ON ON

ON ON OFF OFF

ON ON OFF ON

ON ON ON OFF

OFF ON OFF OFF

OPENING and

CLOSING

OFF ON OFF ON

ON ON ON ON / OPEN PULSE

Tab. 3 - Addressing of BUS Photocells

Table 3 shows the programming operations of the dip-switch

inside the transmitter and of the BUS Photocells receiver.

If the AP Logic was selected, the board begins to count

the pause time (max 10 min) and, after the required time

has elapsed, give an OPENING pulse to continue the pro-

cedure. Otherwise, if you have selected the EP logic, give

an OPEN pulse to continue the procedure.

Leaf 2 (if present) starts the closing movement an the board

begins to count the delay of the leaf at closing.

After the required time has elapsed, give an OPEN pulse

to make leaf 1 start the closing movement. If leaf 2 is not

present, the pulse given in point 9 directly makes leaf 1

close.

Leaves 1 and 2 (if present) stop when they reach the closing

mechanical stop.

Wait for LEDs LD4 and LD5 to go OFF, which means that the

SETUP procedure has finished.

When the SETUP procedure has been started,

if the leaves at point 4 and 5 open instead of

closing, the motor power supply cables must

be changed over.

When using the MANUAL SETUP, the slow-down

spaces, and leaf delays at opening are preset

by the board and cannot be modified. However,

delay at leaf closing and pause time can be

programmed during learning.

10.

11.

12.

13.

14.

Fig. 2 shows a 2-swing leaf automated system indicating the

coverage beams of the photocells:

A: Photocells with OPENING and CLOSING action.

B: Photocells with OPENING action

C: Photocells with OPENING action

D: Photocells with CLOSING action

Fig. 3

ENGLISH

8 MEMORY STORING THE RADIO CODE

The control board has an integrated 2-channel decoding

system (DS, SLH, LC) named OMNIDEC. This system makes it

possible to memory-store both total opening (OPEN A) and

partial opening OPEN B) of the automated system - this is made

possible by an additional receiver module (fig.3 ref. ) and

radio controls on the same frequency.

The 3 types of radio codes (DS, LSH, LC) cannot

coexist.

Only one radio code can be used at a time.

To change over from one code to another, you

must delete the existing one (see paragraph

on deletion), and repeat the memory-storage

procedure.

8.1 MEMORY STORAGE OF AMIGO RADIO

CONTROLS

A maximum of 250 codes can be memory

stored, split between OPEN A and OPEN B.

On the AMIGO radio control, simultaneously press and hold

down push-buttons P1 and P2.

The radio control LED begins to flash.

Release both push-buttons.

Press the LOGIC (SW3) or SPEED (SW2) push-button, to

memory store respectively total opening (OPEN A) or partial

opening (OPEN B), and as you hold it down, also press the

SETUP (SW1) push-button. The relevant LED starts to flash

slowly for 5 sec.

Release both push-buttons.

Within these 5 sec., while the radio control LED is still flashing,

press and hold down the required push-button on the radio

control (the radio control LED lights up on steady beam).

The LED on the board lights up on steady beam for 1

second and then goes OFF, indicating that storage was

executed.

Release the radio control push-button.

Quickly press twice the memory stored radio control push-

button.

The automated system performs one opening

operation. Make sure that the automated

system is free of any obstacle created by

persons or things.

To add other radio controls, transfer the code of the memory-

stored push-button of the radio control to the relevant push-

button of the radio controls to be added, observing the

following procedure.

On the memory stored radio control, simultaneously press

and hold down push-buttons P1 and P2.

The radio control LED begins to flash.

Release both push-buttons.

Press the memory stored push-button and hold it down

(the radio control LED lights up on steady beam).

•

7.2 MEMORY STORAGE OF BUS ACCESSORIES

You can add the BUS photocells to the system at any time,

simply by memory-storing them on the board, observing the

following procedure:

Install and program the accessories using the required

address (see paragraph 7.1)

Cut power to the board.

Connect the two accessories cables to the red terminal-

board J10 (any polarity will do).

Power up the board, taking care to first connect the

main power supply (transformer output) and then any

batteries.

Quickly press once only the SW1 (SETUP) push-button, to

execute learning. The BUS LED flashes briefly.

The board has memory stored the BUS accessories. Follow the

instructions in the table below to check if the BUS connection

is correct.

Tab. 4 - Description of BUS LED

Steady light

Normal operation (LED ON even in the

absence of photocells)

Slow flashing

lamp

At least one photocell engaged or not

aligned

Light OFF

(brief flash

every 2.5 sec.)

BUS line short circuited

Fast flashing

lamp

If you have detected a BUS connection

error, repeat the acquisition procedure. If

the error is repeated, make sure that there

is not more than one accessory with the

same address in the system (also see the

accessories instructions)

Fig. 4

ENGLISH

10 AUTOMATED SYSTEM TEST

When you have finished programming, check if the system is

operating correctly. In particular, check if the safety devices

are operating correctly.

8.2.1 REMOTE MEMORY STORAGE OF BRAVO RADIO

CONTROLS

Other radio controls can be remotely stored only with the BRAVO

radio controls, i.e. without using the RADIO SETUP push-buttons,

but using a previously stored radio control.

Get a radio control already stored on one of the 2 channels

(OPEN A or OPEN B ).

Press and hold down push-buttons P1 and P2 simultaneously

until both the LEDs flash slowly for 5 sec.

Within 5 sec. press the push-button of the radio control

that had been memory stored to enable learning on the

selected channel.

The LED on the board relating to the channel being learned

flashes for 5 sec., within which time the code of another

radio control must be transmitted.

The LED lights up on steady beam for 2 seconds, indicating

memory storage executed, and then resumes flashing for

5 sec., during which other radio controls can be memory

stored, and then goes OFF.

Bring the radio controls near, press and hold down the

push-button of the radio control to be added, releasing

it only after the double flash of the radio control LED,

which indicates memory storage executed.

Quickly press twice the push-button of the memory stored

radio control.

The automated system performs one opening

operation. Make sure that the automated

system is free of any obstacle created by

persons or things.

8.2 MEMORY STORAGE OF BRAVO RADIO CONTROLS

(for some markets only)

A maximum of 250 codes can be memory

stored, split between OPEN A and OPEN B.

Use BRAVO remote controls only with receiver module at

433 MHz.

Press the LOGIC (SW3) or SPEED (SW2) push-button, to

memory store respectively total opening (OPEN A) or partial

opening (OPEN B), and as you hold it down, also press the

SETUP (SW1) push-button. The relevant LED starts to flash

slowly for 5 sec.

Release both push-buttons. Within these 5 sec., press the

appropriate push-button on the LC remote control.

The LED lights up on steady beam for 1 second, indicating

memory storage executed, and then resumes flashing for

another 5 sec., during which another radio control (point

4) can be memory stored.

When the 5 sec. have elapsed, the LED goes OFF indicating

the end of the procedure.

To add other radio controls, repeat the operation at point 1.

•

8.3 RADIO CONTROLS DELETION PROCEDURE

To delete ALL the input radio control codes, press push-

button LOGIC (SW3) or SPEED (SW2) and, while holding it

down, also press push-button SETUP (SW1) for 10 sec.

The LED relating to the pressed push-button flashes for

the first 5 sec, and then flashes more quickly for the next

5 sec.

Both LEDs light up on steady beam for 2 sec and then go

OFF (deletion completed).(deletion completed).deletion completed). completed).completed).).

Release both push-buttons.

This operation is NOT reversible. All codes of

radio controls stored as OPEN A and OPEN B will

be deleted.

9 CONNECTION OF BUFFER BATTERIES (OPTIONAL)

The buffer battery kit will activate the automated system

in the event of a power cut. The batteries are housed in

an appropriate container located inside the operator (see

sequence in fig.4).

To install, consult the specific instructions.

The batteries come into operation when a

power cut occurs. During operation with the

battery, the flashing lamp flashes rapidly (120

ms) every second, whereas during operation

with the mains transformer, the flashing lamp

flashes long (300 ms) every second.

During operation with the battery, all BUS

safety accessories are powered down to save

on energy. They are re-activated by an OPEN

command.

Tab. 5

Tab. 6

ENGLISH

11 LOGIC TABLES

(1) If the cycle began with OPEN-B (partial opening), an OPEN-A pulse will activate both leaves to open.

LOGIC “AP” PULSES

STATUS OF AUTOMA-

TED SYSTEM

OPEN A OPEN B STOP FSW-OP FSW-CL FSW-OP/CL

FSW-OPEN

CLOSED

opens leaves and

closes after pause

time

opens leaf 1 and clo-

ses after pause time

no effect (opening

inhibited)

no effect (opening

inhibited)

no effect

no effect (opening

inhibited)

opens leaves and

closes after pause

time

OPENING stops operation (1) stops operation stops operation

reverses immediately

at closing

no effect

stops and continues

to open at

disengagement

no effect (1)

OPEN IN PAUSE stops operation (1) stops operation stops operation no effect

recharges pause

time

(closing inhibited)

recharges pause

time

(closing inhibited)

recharges pause

time

(closing inhibited) (1)

CLOSING

reverses immediately

at opening

no effect stops operation no effect

reverses immediately

at opening

stops and, at

disengagement,

reverses at opening

reverses immediately

at opening

STOPPED closes closes

no effect (opening

and closing inhibited)

no effect (opening

inhibited)

no effect (closing

inhibited)

no effect (opening

and closing inhibited)

opens leaves

LOGIC “EP” PULSES

STATUS OF AUTOMA-

TED SYSTEM

OPEN A OPEN B STOP FSW-OP FSW-CL FSW-OP/CL FSW-OPEN

CLOSED opens leaves opens leaf 1

no effect (opening

inhibited)

no effect (opening

inhibited)

no effect

no effect (opening

inhibited)

opens leaves

OPENING stops operation (1) stops operation stops operation

reverses immediately

at closing

no effect

stops and continues

to open at

disengagement

no effect (1)

OPEN closes closes

no effect (closing

inhibited)

no effect

no effect (closing

inhibited)

no effect (closing

inhibited)

no effect (1)

CLOSING stops operation stops operation stops operation no effect

reverses immediately

at opening

stops and, at

disengagement,

reverses at opening

reverses immediately

at opening

STOPPED

After OPEN: Restarts moving in reverse

direction

After STOP: Re-closes the leaf/ves

immediately (1)

no effect (opening

and closing inhibited)

no effect (opening

inhibited)

no effect (closing

inhibited)

no effect (opening

and closing inhibited)

opens leaves

Page is loading ...

Genius BRAIN 06 Operating instructions

Brand: Genius

Model: BRAIN 06

Type: Operating instructions

Download PDF

report

in other languages

italiano: Genius BRAIN 06 Istruzioni per l'uso
français: Genius BRAIN 06 Mode d'emploi
español: Genius BRAIN 06 Instrucciones de operación
Deutsch: Genius BRAIN 06 Bedienungsanleitung
Nederlands: Genius BRAIN 06 Handleiding

Genius BRAIN 06 Operating instructions

Genius BRAIN 06 Operating instructions

in other languages

Related papers

Other documents