Mazda 2001 Owner's manual

Before driving

Introduction 2

Instrumentation 6

Controls and features 17

Seating and safety restraints 63

Starting and driving

Starting 100

Driving 105

Roadside emergencies 132

Servicing

Maintenance and care 151

Capacities and specifications 206

Customer assistance 211

Index 217

photocopying, recording or by any information storage and retrieval system or translation

in whole or part is not permitted without written authorization from Mazda Corporation.

Mazda may change the contents without notice and without incurring obligation.

Contents

1

ICONS

Indicates a safety alert. Read the

following section on Warnings.

Indicates vehicle information related

to recycling and other

environmental concerns will follow.

Correct vehicle usage and the

authorized disposal of waste

cleaning and lubrication materials are significant steps towards

protecting the environment.

Indicates a message regarding child

safety restraints. Refer to Seating

and safety restraints for more

information.

Indicates that this Owner Guide

contains information on this subject.

Please refer to the Index to locate

the appropriate section which will

provide you more information.

WARNINGS

Warnings provide information which may reduce the risk of personal

injury and prevent possible damage to others, your vehicle and its

equipment.

BREAKING-IN YOUR VEHICLE

There are no particular breaking-in rules for your vehicle. During the

first 1,600 km (1,000 miles) of driving, vary speeds frequently. This is

necessary to give the moving parts a chance to break in.

INFORMATION ABOUT THIS GUIDE

The information found in this guide was in effect at the time of printing.

Mazda may change the contents without notice and without incurring

obligation.

Introduction

2

EMISSION WARRANTY

The New Vehicle Limited Warranty includes Bumper to Bumper

Coverage, Safety Restraint Coverage and Corrosion Coverage. In addition,

your vehicle is eligible for Emissions Defect and Emissions Performance

Warranties. For a detailed description of what is covered and what is not

covered, refer to the Warranty Guide that is provided to you along with

your Owner’s Guide.

SPECIAL NOTICES

Notice to owners of pickup trucks and utility type vehicles

WARNING: Utility vehicles have a significantly higher rollover

rate than other types of vehicles.

Before you drive your vehicle, please read this Owner’s Guide carefully.

Your vehicle is not a passenger car. As with other vehicles of this type,

failure to operate this vehicle correctly may result in loss of control or an

accident.

If your vehicle is a 4x4, be sure to read Driving off road with 4x4 auto

in the Driving chapter.

Using your vehicle with a snowplow

WARNING: Do not use this vehicle for snowplowing.

Introduction

3

These are some of the symbols you may see on your vehicle.

Vehicle Symbol Glossary

Safety Alert

See Owner’s Guide

Fasten Safety Belt Air Bag-Front

Air Bag-Side Child Seat

Child Seat Installation

Warning

Child Seat Tether

Anchorage

Brake System Anti-Lock Brake System

Brake Fluid -

Non-Petroleum Based

Traction Control

Master Lighting Switch Hazard Warning Flasher

Fog Lamps-Front Fuse Compartment

Fuel Pump Reset Windshield Wash/Wipe

Windshield

Defrost/Demist

Rear Window

Defrost/Demist

Power Windows

Front/Rear

Power Window Lockout

Introduction

4

Vehicle Symbol Glossary

Child Safety Door

Lock/Unlock

Interior Luggage

Compartment Release

Symbol

Panic Alarm Engine Oil

Engine Coolant

Temperature

Do Not Open When Hot Battery

Avoid Smoking, Flames,

or Sparks

Battery Acid

Explosive Gas Fan Warning

Power Steering Fluid

Maintain Correct Fluid

Level

MAX

MIN

Emission System Engine Air Filter

Passenger Compartment

Air Filter

Jack

Check fuel cap

Introduction

5

RSM

CST

SET

ACC

OFF

ON

Instrument cluster

(pg. 8)

Windshield wiper/

washer control

(pg. 42)

Manual tilt steering

wheel lever

(pg. 38)

Speed controls*

(pg. 38)

Instrument panel

dimmer control

(pg. 17)

Power mirror

control*

(pg. 17)

Fog lamp

control*

(pg. 48)

Headlamp and turn

signal control

(pg. 48)

* if equipped

Instrumentation

6

OFF

AM/FM

TAPE

CD

SCAN

12 3

45 6

LOAD

CLOCK

AUTO-M

PRO

RPT

RDM/BS

TR/APC TR/APC

FFREW

TUNE

SEEK

DISC

PUSH

POWER VOL

PUSH

AUDIO CONT

LOCK

Audio system

(pg. 22)

4wd control*

(pg. 18)

Climate controls

(pg. 19)

Auxiliary power point

(pg. 51)

Rear window

defroster control

(pg. 18)

Hazard flasher control

(pg. 132)

Instrumentation

7

WARNING LIGHTS AND CHIMES

Service engine soon

Your vehicle is equipped with a

computer that monitors the engine’s

emission control system. This

system is commonly known as the

On Board Diagnostics System (OBD II). The OBD II system protects the

environment by ensuring that your vehicle continues to meet

government emission standards. The OBD II system also assists the

service technician in properly servicing your vehicle.

The

indicator light illuminates when the ignition is first turned to

the RUN position to check the bulb. If it comes on after the engine is

started, one of the engine’s emission control systems may be

malfunctioning. The light may illuminate without a driveability concern

being noted. The vehicle will usually be drivable and will not require

towing.

What you should do if the light illuminates

Light turns on (without blinking):

This means that the OBD II system has detected a malfunction.

Temporary malfunctions may cause your

light to illuminate.

Examples are:

1. The vehicle has run out of fuel. (The engine may misfire or run

poorly.)

2. Poor fuel quality or water in the fuel.

3. The fuel cap may not have been properly installed and securely

tightened.

CHECK

FUEL

CAP

Instrumentation

8

These temporary malfunctions can be corrected by filling the fuel tank

with high quality fuel of the recommended octane and/or properly

installing and securely tightening the gas cap. After three driving cycles

without these or any other temporary malfunctions present, the

light should turn off. (A driving cycle consists of a cold engine startup

followed by mixed city/highway driving.) No additional vehicle service is

required.

If the

light remains on, have your vehicle serviced at the first

available opportunity.

NOTE: The light will illuminate if vehicle refueling is conducted

with the engine running.

WARNING: Never refuel vehicle with the engine running.

Light is blinking:

Engine misfire is occurring which could damage your catalytic converter.

You should drive in a moderate fashion (avoid heavy acceleration and

deceleration) and have your vehicle serviced at the first available

opportunity.

WARNING: Under engine misfire conditions, excessive exhaust

temperatures could damage the catalytic converter, the fuel

system, interior floor coverings or other vehicle components,

possibly causing a fire.

Low fuel

Illuminates as an early reminder of a

low fuel condition indicated on the

fuel gauge (refer to Fuel gauge in

this chapter for more information).

When refueling, after the light

comes on, the amount of fuel that can be added will be less than the

advertised capacity due to the reserve fuel. The ignition must be in the

RUN position for this lamp to illuminate. The lamp will also illuminate for

several seconds after the ignition is turned to the ON position regardless

of the fuel level to ensure your bulb is working.

Instrumentation

9

Air bag readiness

Momentarily illuminates when the

ignition is turned ON. If the light

fails to illuminate, continues to flash

or remains on, have the system

serviced immediately.

Safety belt

Momentarily illuminates when the

ignition is turned to the ON position

to remind you to fasten your safety

belts. For more information, refer to

the Seating and safety restraints

chapter.

Brake system warning

Momentarily illuminates when the

ignition is turned to the ON position

to ensure the circuit is functional.

Also illuminates if the parking brake

is engaged. If the brake warning lamp does not illuminate at these times,

seek service immediately.

WARNING: Illumination after releasing the parking brake

indicates low brake fluid level and the brake system should be

inspected immediately.

Anti-lock brake system (ABS) (if equipped)

Momentarily illuminates when the

ignition is turned to the ON position

to ensure the circuit is functional.

WARNING: If the light remains on, continues to flash or fails

to illuminate, have the system serviced immediately. With the

ABS light on, the anti-lock brake system is disabled and normal

braking is still effective unless the brake warning light also

remains illuminated with the parking brake released.

ABS

Instrumentation

10

Turn signal

Illuminates when the left or right

turn signal or the hazard lights are

turned on. If one or both of the

indicators stay on continuously or

flash faster, check for a burned-out

turn signal bulb. Refer to Bulbs in the Maintenance and care chapter.

High beams

Illuminates when the high beam

headlamps are turned on.

Speed control

This light comes on when the

vehicle speed control is engaged and

actively controlling the vehicle

speed. It turns off when the speed control OFF or CANCEL controls are

pressed, the brake or clutch (if equipped) is applied or the ignition is

turned to the OFF position after stopping the vehicle.

Anti-theft system

Refer to SecuriLocky passive

anti-theft system in the Controls

and features chapter.

Charging system

Illuminates when the ignition is

turned to the ON position and the

engine is off. The light also

illuminates when the battery is not

charging properly, requiring

electrical system service.

CRUISE

Instrumentation

11

Engine oil pressure

Momentarily illuminates when the

ignition is turned to the ON

position. Illuminates when the oil

pressure falls below the normal

range when the engine is running.

To avoid engine damage, stop the vehicle as soon as safely

possible and switch off the engine immediately. Check the oil

level and add oil if needed.

Refer to Engine oil in the Maintenance and care chapter.

Four wheel drive indicator (if equipped)

Illuminates when 4x4 switch control

is turn to the ON position.

NOTE: If the light continues to

flash have the system serviced.

Door ajar

Illuminates when any door, liftgate

or liftgate window is open.

O/D off

Illuminates when the Transmission

Control Switch (TCS), refer to

Overdrive control in the Driving

chapter, has been pushed turning

the transmission overdrive function OFF. When the light is on, the

transmission does not operate in the overdrive mode, refer to the

Driving chapter for transmission function and operation.

The light may also flash steadily if a transmission malfunction is

detected. If the light does not come on when the Transmission

Control Switch is depressed or if the light flashes steadily, have

your vehicle serviced as soon as possible or damage to the

transmission could occur.

O/D

OFF

Instrumentation

12

Low coolant (if equipped)

This lamp will illuminate when the

engine coolant inside the reservoir is

low. This lamp will illuminate when

the ignition is first turned to the ON

position, but then should turn off.

If the lamp stays on, to avoid engine damage you should allow the

engine to cool down, then check the coolant level inside the

reservoir.

For instructions on adding coolant, see Engine coolant in

theMaintenance and care chapter.

Check fuel cap (if equipped)

Momentarily illuminates when the

ignition is turned to the ON position

to ensure your bulb is working.

When this light turns on, check the

fuel filler cap. Continuing to operate

the vehicle with the check fuel cap light on, can activate the

warning light. When the fuel filler cap is properly re-installed, the

light(s) will turn off after a period of normal driving. This period will

vary depending on driving conditions.

It may take a long period of time for the system to detect an

improperly installed fuel filler cap.

For more information, refer to Fuel filler cap in the Maintenance and

care chapter.

Safety belt warning chime

Sounds to remind you to fasten your safety belts.

For information on the safety belt warning chime, refer to the Seating

and safety restraints chapter.

Belt minder chime

Sounds intermittently to remind you to fasten your safety belts.

For information on the safety belt minder chime, refer to the Seating

and safety restraints chapter.

CHECK

FUEL

CAP

Instrumentation

13

Supplemental restraint system (SRS) warning chime

For information on the SRS warning chime, refer to the Seating and

safety restraints chapter.

Key-in-ignition warning chime

Sounds when the key is left in the ignition in the OFF/LOCK or ACC

position and any door, liftgate or liftgate window is opened.

Headlamps ON warning chime

Sounds when the headlamps or parking lamps are on, the ignition is off

(and the key is not in the ignition) and any door is opened.

GAUGES

Engine coolant temperature gauge

Indicates the temperature of the

engine coolant. At normal operating

temperature, the needle remains

within the normal area (the area

between the “H” and “C”).

If it enters the red section, the

engine is overheating. Stop the vehicle as soon as safely possible,

switch off the engine immediately and let the engine cool. Refer to

Engine coolant in the Maintenance and care chapter.

WARNING: Never remove the coolant reservoir cap while the

engine is running or hot, this may result in serious burns.

CHECK

FUEL

CAP

Instrumentation

14

NOTE: This gauge indicates the temperature of the engine coolant, not

the coolant level. If the coolant is not at its proper level the gauge

indication will not be accurate.

Tachometer

Indicates the engine speed in

revolutions per minute.

Driving with your tachometer

pointer continuously at the top

of the scale may damage the

engine.

Speedometer

Indicates the current vehicle speed.

Fuel gauge

Displays approximately how much

fuel is in the fuel tank (when the

key is in the ON position). The fuel

gauge may vary slightly when the

vehicle is in motion. The ignition

should be in the OFF/LOCK position

while the vehicle is being refueled. When the gauge first indicates empty,

there is a small amount of reserve fuel in the tank. When refueling the

vehicle from empty indication, the amount of fuel that can be added will

be less than the advertised capacity due to the reserve fuel.

NOTE: The fuel filler door is located on the driver’s side of the vehicle.

Instrumentation

15

Odometer

Registers the total kilometers

(miles) of the vehicle.

Trip odometer

Registers the kilometers (miles) of

individual journeys. Press and hold

the button for 1 or more seconds to

reset. Press and release the button

in less than 1 second to toggle

between odometer and trip

odometer.

Instrumentation

16

INSTRUMENT PANEL DIMMER CONTROL

Use to adjust the brightness of the instrument panel.

• Push and hold top of control to

brighten.

• Push and hold bottom of control

to dim.

POWER MIRROR CONTROL

The ignition must be in the ACC or ON position to adjust the power side

view mirrors.

To adjust your mirrors:

1. Rotate the control clockwise to

the right position to adjust the

right mirror and rotate the

control counterclockwise to the

left position to adjust the left

mirror.

2. Move the control in the

direction you wish to move the

mirror.

3. Return to the center position to lock mirrors in place.

Controls and features

17

Fold-away mirrors

Pull the side mirrors in carefully

when driving through a narrow

space, like an automatic car wash.

FOUR WHEEL DRIVE (4X4) CONTROL (IF EQUIPPED)

This control operates the four wheel

drive (4X4) system. Refer to the

Driving chapter for more

information.

REAR WINDOW DEFROSTER CONTROL

The rear defroster control is located

on the instrument panel.

Press the rear defroster control to

clear the rear window of thin ice

and fog.

• The small LED will illuminate

when the rear defroster is

activated.

The ignition must be in the ON position to operate the rear window

defroster.

NOTE: The defroster turns off automatically when the ignition is turned

to the OFF position. To manually turn off the defroster push the control

again.

HAZARD FLASHER

For information on the hazard flasher control, refer to Hazard flasher in

the Roadside emergencies chapter.

LOCK

Controls and features

18

CLIMATE CONTROL SYSTEM

Manual heating and air conditioning system

Fan speed control

Controls the volume of air circulated

in the vehicle.

Temperature control knob

Controls the temperature of the

airflow inside the vehicle.

Mode selector control

Controls the direction of the airflow

to the inside of the vehicle.

The air conditioning compressor will operate in all modes except

,

and . However, the air conditioning will only function if the

outside temperature is about 6°C (43°F) or higher.

Since the air conditioner removes considerable moisture from the air

during operation, it is normal if clear water drips on the ground under

the air conditioner drain while the system is working and even after you

have stopped the vehicle.

Under normal conditions, your vehicle’s climate control system should be left

in any position other than MAX A/C or OFF when the vehicle is parked. This

allows the vehicle to “breathe” through the outside air inlet duct.

A/C

OFF

MAX

A/C

OFF

MAX

A/C

Controls and features

19

NOTE: In snowy or dirty conditions, leave the mode selector in the OFF

position.

• MAX A/C- Uses recirculated air to cool the vehicle. MAX A/C is noisier

than A/C but more economical and will cool the inside of the vehicle

faster. Airflow will be from the instrument panel registers. This mode

can also be used to prevent undesirable odors from entering the

vehicle.

• A/C-Uses outside air to cool the vehicle. It is quieter than MAX A/C

but not as economical. Airflow will be from the instrument panel

registers.

•

(Panel)-Distributes outside air through the instrument panel

registers. However, the air will not be cooled below the outside

temperature because the air conditioning does not operate in this

mode.

• OFF-Outside air is shut out and the fan will not operate. For short

periods of time only, use this mode to prevent undesirable odors from

entering the vehicle.

•

(Panel and floor)-Distributes outside air through the instrument

panel registers and the floor ducts. Heating capabilities are provided in

this mode. For added customer comfort, when the temperature

control knob is anywhere in between the full hot and full cold

positions, the air distributed through the floor ducts will be slightly

warmer than the air sent to the instrument panel registers. However,

the air will not be cooled below the outside temperature because the

air conditioning does not operate in this mode.

•

(Floor)-Allows for maximum heating by distributing outside air

through the floor ducts. However, the air will not be cooled below the

outside temperature because the air conditioning does not operate in

this mode.

•

(Floor and defrost)-Distributes outside air through the

windshield defroster ducts and the floor ducts. Heating and air

conditioning capabilities are provided in this mode. For added

customer comfort, when the temperature control knob is anywhere in

between the full hot and full cold positions, the air distributed through

the floor ducts will be slightly warmer than the air sent to the

windshield defrost ducts. If the temperature is about 6°C (43°F) or

higher, the air conditioner will automatically dehumidify the air to

reduce fogging.

Controls and features

20

Page is loading ...

Mazda 2001 Owner's manual

This manual is also suitable for

Mazda 2001 Owner's manual

Related papers

Other documents