INSTRUCTION MANUAL
C29ZK80TX
Colour Television
II
f
1)
TELETEn
Video Multi Terminal (PAIJNTSC/NTSC4.43)
Blue Back Function on AV mode
Electric Mains............................................................................. 2
Battery installation of the Remote Control Transmitter ............. 2
Warnings and Cautions ............................................................ 3
Controls / Remote Control Transmitter ..................................... 5
General Operation
Power ON/OFF, Programme Selection (Direct Selection).. 6
Programme Selection (Programme UP and Down)............ 7
Volume Control, Recall, Alternate
........................................
7
Sound Mute, OFF Timer, Memory, Normalization ............... 8
Picture Adjustments .............................................................. 9
Tuning of the Channels
Automatic Tuning, Channel Copy......................................... 10
Semi-Auto Tuning, Manual Tuning ....................................... 11
Teletext Use ...............................................................................l2
Setting Restricted Programmed .................................................17
Maximum volume level setting and
suppression of channel tuning
...................................................
18
Connecting other Equipment
Connecting to the AV input Jacks ....................................... 19
Connecting to the AV Output Jacks ..................................... 19
To record a TV broadcast while watching the playback
from a VCR
...........................................................................
20
AV Connection to the Aerial Socket ..................................... 20
Aerial Connection
......................................................................
21
Specifications ............................................................................. 22
Memo
..........................................................................................
23
The receiver designed to operate on an A.C. mains supply
of 220 – 240 Volts, 50Hz.
❑ Remove the battery cover by sliding.
❑ Install two “AA” 1.5volt batteries so that the “+” and “-”
marks on the batteries match the “+” and ”-” marks
inside the unit.
❑Close the battery cover.
Note: Replace the batteries when the TV set is showing the following symptoms:
Operation is unsteady or erratic, sometimes the TV set does not work with transmitter.
Discharged batteries may leak and damage the unit.
The normal life of batteries should be from nine to ten months.
A
Warning
High voltages are used in the opsration of this television
receiver. Do not remove the cabinet back from your set.
Refer servicing to qualified service personnel.
A
Warning
To prevent fire or electrical shock hazard, do not expose
the television receiver to rain or moisture.
A
Warning
Do not drop or push objects into the television cabinet
slots or openings.
Never spill any kind of liquid on the television receiver.
, ~cm Minimum distances
1Ocm
~
~ ~
5cm
A
I
Caution
●
20cm
If the television is to be buiit into a
compartment or simiiariy enciosed, the
minimum distances must be maintained.
Heat build-up can reduce the service iife of
your television, and can also be dangerous.
A
I Caution
●
Never stand on, lean on or push suddenly the television or its
stand. You should pay special attention to children. Serious
injury may result if it should fall.
A
1 Caution
●
Do not place your television on an unstable cart, stand, shelf or
}1
table. Serious injury to an individual, and damage to the
television, may result if it should fall.
A
I Caution
●
When the television receiver is not used for an extended period
of time, it is advisable to disconnect the AC power cord from
the AC outlet.
.*.
-)
,...-
.....
A
I Caution
●
*-.
#
(.,$..
Avoid exposing the television receiver to direct sunlight and
‘. :
: ‘.
other source of heat.
:
Do not stand the television receiver directly on other products
which give off heat.
E.g. video cassette players, audio
amplifiers.
. . .
‘.
:
:
,s.
A
! Caution
●
Do not block the ventilation holes in the back cover.
Adequate ventilation is essential to prevent failure of electrical
components.
A
I Caution
●
Do not squash power supply cord under the television receiver,
Controls ~~
,.,.,.,.,.,.
............
............
............
............
::::::::.::
............
............
:~
............
Remote Control Detector
,.,.,.,,,...
,.,.,.,.,...
............
............
............
............
......
:.:.:.x.:.
............
............
............
:::::::yf
Stand-by and Power lndicator—
::::::::::::
.:.:.?..:.:
:.:.:.:.:.:.
:::::::fi
::::::::::
::::::::::::
............
............
............
............
:::::::~
●
+
............
,
&
I
/ (* If.)
m
Mains ON/OFF
Push to open
Switch
b
Q
SYSTEM I
-A +
vPA
LEvEL
Programme UP/DOWN
Headphone Jack
MEMORY/PRESET
(For personal listening, a headphone can be
COLOUR SYSTEM Selector
connected to the headphone jack.)
Remote Control Transmitt
~
Digit
~ F’$g~;me
FUNCTION
SOUND MUTE
OFF TIMER
N
~
To switch the TV on or off;
To set the TV into standby mode;
Press the Mains ON/OFF
button ~
The power of the lV is turned on,
or off completely.
EE!w
~3
,:.:.,.,.:.:.:.:p*
..:.:.:.:.:.:.:*.:.:.,.,.,.
?!58
&
Press the Power ON/OFF button ~
To turn the TV on, press again.
important !
Be sure to set the Mains ON/OFF switch O to the off position, if
the power failure occurs while viewing.
To turn on the TV from standby
mode;
Press
@
x
Power ON/OFF 6Q
(remote control transmitter)
v
Programme UP/DOWN ~
(remote control transmitter)
or
1 to 9,0 Key
)?
(remote control
transmitter)
v
or
VPA
&
Pro ramme
UP/~OWN ~
(lV set)
AUTO SHUT OFF
This TV set incorporates the AUTO SHUTOFF function.
$
Remainingtime
Even if the lV is left on after you have gone to sieep, the TV set changes
to the standby mode within 10 minutes after aii broadcasts have ended.
-lo
29
(Direct Seiection)
For exampie
To seiect a programme directiy
ml
Programme
Seiector
b=
●
Digit
‘To seiect programme 8
8
&
J
8
(To seiect programme 10
I
“-- Press the Digit ~ key. ‘
&
J
.-
‘638>1
1
Programme Selection
(Programme UP and
Down)
\
#
To select a channel
Front controls of the TV
SYSTEM OF
-e
Pro ramme
UP/BOWN
3
*
.
Programme UP/DOWN ~
Remote Control Transmitter
\
[
Volume Control
To adjust the sound volume
r-- ‘ ‘
.
.’.’.”.’.”.”.ma:ma:
or
.4+
vPA
SYSTSU o
~ LEVEL
f’
11=1- —
...u._ .
—11
II 1-
Ilwwuwll
r
LEVEL Q
I
RECALL
To display the on screen indications,
COLOUR SYSTEM button.
press the RECALL /
/r
Programme
Position
Off Timer–
LLL/
)UR
-0
REC,
COL[
SYS
EM
Screen display disappears after
about 5 seoonds.
I
ALTERNATE
Press the ALTERNATE @ key, and the programme position will
I
I I 1
.
I
alternately select the previous position and the present position.
4
2
I
-0
For example, now you are watching programme position
ALTERNATE
“4” but you watched programme position “2” previously. If
you press the ALTERNATE key, programme position “2”
immediately appears.
6
I
u
PEELl
Should you wish to mute the sound (e.g. While talking on
the telephone), press the SOUND MUTE @ key.
I
OFF TIMER
1
L
~ SOUND MUTE
@SOUND MUTE
111111---------
The lV set will be turned off after about 30,60,90 or 120 minutes.
Press the OFF TIMER @ key.
I
-00 al
To switch the sound back on,
press the SOUND MUTE key
again.
-30+
I
- 60
I
L
No off timer
After 30 minutes
?
After 60 minutes
I
I
~OFF TIMER
After 120 minutes
After 90 minutes
~
Just one minute before switching off the TV, ” – 01”
To cancel the OFF TIMER
and channel number will be displayed on the
Press the OFF TIMER key until” – 00” appears.
This function lets you store the settings (for colour, brightness, contrast, tint, sharpness, sound volume)in the memory for
both picture and sound, and these setting levels can be recalled by pressing the NORMALIZATION @key of the remote
control transmitter.
To store the picture and sound settings
I I
(1) Set the picture and sound to the desired levels. —>
etc.
. . ------ -
(2) Press the MEMORY/PRESETO Q button whiie the control function display is still visible on the screen.
AIK!!!L“ “=
~ ~ MEMORY/PRESET
NOTE: The controi settings will not be saved if the MEMORY button is pressed after the control function display has
left the screen.
~
lxEJ
Press the NORMALIZATION @ key.
w
The coiour, brightness, contrast, tint, sharpness and
.
9
sound volume settings which you stored using the
MEMORY button are recalled.
PICTURE ADJUSTMENTS
(1) Select the adjustment item using the FUNCTION ~ key. (2) Adjust using the LEVEL @ + and – key.
;,:::::::::::::.:...,
,...
.A:;:::;:::::ti.
;[ - ..........p...,:.:,,.-
,,::(—’{:::
:.:
... ,,, ,,, ,,, ,,, ,,,,,,,,,, ,,, ,, ,,, ,,, ,,, ,,,
..:’::’:’:’:’:’*:::’::::*:::::::?+:::::::?:%:
?5
FUNCTION
LEVEL
or
or
P-M--%
-A +
vPA
SYSTEM o
-A +
vPA
SYSTEM
v h FUNCTION
LEVEL ~
Each time the FUNCTION key is pressed, function choice will change as follows;
+
+
@ COLOUR
11111111111 ----
~C20NTRAST
11111111111----
~ BRIGHT
11111111111----
A TINT
-------t-i -----
Colour intensity
Contrast
Tint
Brightness
(Operative for NTSC4.43
and NTSC signal only)
L
+I+r
j I ‘> ] p:!!:!!:::...
Fine tuning
Sharpness
(Operative for TV mode only)
Display off
There are three ways of tuning as follows;
Automatic Tuning (the basic way)
All receivable channels are automatically tuned in and memorized in consecutive programme positions.
Semi-Auto Tuning
Use to preset a receivable channel in any desired programme position, e.g. the position with the same number as the
channel.
Manual Tuning
Manually tune a channel if it cannot be automatically tuned, such as when the signal is poor.
~
(1) Press the MEMORY/PRESET button ~,
—
-A +
VPA
Programme
Position
AUTO TUNING 2
L IIIIiIIIi------
“b
MEMORY/PRESET
Channei Band
(2) Press the LEVEL(+) @ button.
m ‘Ysi
LEvEL(+)~ v
L u---------
. . .
I
The channels are preset in consecutive positions beginning from
I
the programme position”1”.
m
●
●
After all availabie channels have been preset, the unit returns to
●
●
the position”1”.
Note: To cancel automatic tuning midway, press the MEMORY/
PRESET ~ or Power ON/OFF ~ button.
, +oooo”~
Channel Copy
Exampie: To copy the TV channei in the programme position 2 into the programme position 6
(1) Seiect programme position 2 using Programme selector ~.-
2
I
(2) Press the MEMORY/PRESET button @ 3 times. ->
MANUAL
2
I
m
MANUAL
(3) Select programme position 6 using Programme UP/DOWN ~ button of the TV set.
d
+
L
111111111------ 6
(4) Press FUNCTiON button O
.~ hNu.L I e ‘~ ~
--l
(5) Press the MEMORY/PRESET button @.
~,,,
Semi-Auto Tuning & Manual Tuning
Example: To preset a channel in programme position
I Semi-Auto Tuning
I
6
I
Manual Tuning
I
&
(1) Select programme position 6 using Programme selector ~.
L
Xllf
(2) Press the MEMORY/PRESET button ~ twice. >
( (2) Press the MEMORY/PRESET button Q 3 times.
H &p_
I
MEMORY/PRESET
w
(3) Press the LEVEL(+) or(–) @button.
(5) Press and hold the LEVEL(+) or(–) ~ buttor
until the desired station appears.
!= $.$i
17:’---6
]
When a station is found,
searching stops automatically.
b
LEVEL
Jlf’
J+’
r(4) Press FUNCTION button ~ .
. w “s+ h?::o. M.
z(5) Press the MEMORY/PRESET button @ twice.
(7) Press the MEMORY/PRESET button @ .
L
\
6
I
“u
This completes the presetting.
This completes the presetting.
Repeat steps 1 to 5 for other desired channels.
●
SIZE
lV/TEXT/MIX
CANCEL(RED)
REVEAL(GREEN)~
Page Selection 1~
Page
UP(
A )/DOWN( V )—
i
■ Switching to the Teietext mode
HOLD
—INDEX
TIME/SUB(CYAN)
—YELLOW
- Digit —1
Press the TV~EXT/MIX button, and the screen changes as follows:
v
>
(1) To use CANCEL, REVEAL or TIME/SUB in Text
mode, press the Digit button first.
1
To return to the normal text
display, press the Digit button
again.
(t-l)~G
1
You can use CANCEL, REVEAL
or TIME/SUB when this display is
shown.
(2) Next, press the CANCEL, REVEAL or TIME/SUB
key.
d
I
‘“”/588
*
*
.....
..
.(.
& I
ryl-g-
■ Page Seiection
Direct Page Access
A Teletext page can be
selected with the “O”to
“~ buttons.
UP- DOWN Page Access
m
TV&&Xl
m
I
For example:
&+&+&’
j-l
To select page 120, press
Press the Page UP(A) button to step up to the next higher Teletext page.
Press the Page DOWN(V) button to step down to the next lower Teletext page.
■ To display the index Page
To return to the index page, press the INDEX button
■ Sub-Coded Page Access
When a Teletext information page exceeds more than one screen of information, it may take some time for the automatic
changing of the sub- pages to reach the sub-page you require.
It is possible to enter your required sub- page and continue watching the normal programme until the correct sub- page is
found,
(1) Select a text page which has sub pages.
(2) Press the Digit button.
:1‘E%!%IG:
“.”.”.”.””.::y:.:.:.:.:
(3) Press the TIME/SUB button.
[1‘h
* ~]]agam.
‘8”888
To go back to normal Teletext page
Xm
x
ent~ mode, press the Digit button
,.,., ,.:.:
\
.
/
(4)
Enter the desired sub- page.
Example:
To enter the sub
page “1O“, you must
press the O,0, 1, and
Obutton.
&~~~ ~=1
(5) Press the CANCEL button.
“ ~ mlq=g~;:{’:${’: ‘
CANCEL Normal TV Picture
Normai TV Picture
(6) Press the TV/TEXT/MIX button to display the received sub- page.
H Viewing TV while searching for a page
Note:
To clear the sub-coded page, enter a new page number.
it is not possible to select another television station during a
sub - page access operation.
In some cases it can take some time to look for a page. in the intervai you can view the TV by pressing
the Digit and
CANCEL button.
Fl+~+&!+
Digit
CANCEL
TV/TEXT/MIX
Q
Normai TV Picture
P351 P308
When the page arrives,
TEXT
the page number will
PAGE
appear on the normal TV
picture.
(x) (?) S****
w
P351
v
TEXT
PAGE
350 352 360 400
When a text page has sub- pages, you can prevent the sub
page being automatically changed by pressing the HOLD
button. Press the HOLD button again to resume page change
or enter a new page number.
m
(??
HOLD
TEXT PAGE
HOLD
■ Double letter height
f
1
Either the top or bottom half of the
display can be expanded by pressing
the SIZE button.
SIZE
DISPLAY
t
Upper half of
Lower half of
the screen
the screen
I
■ Displaying concealed information
Some of the text pages are in the form of a quiz or puzzle.
The answer to these can be revealed by pressing the Digit and REVEAL button.
“
(q-&f=J((+-l
3
Digit
REVEAL
REVEAL
\
)
■ News flash
(1)In the text mode, select (2) Press the Digit button,
a newsflash page.
P500
NEWS FIASH
599 501 510 600
NEWS FLASH
(x) (?) S****
(TEXT mode)
(TEXT mode)
(3) Press the CANCEL (4) AS soon as news comes
during a NEWS FIASH. You should first switch
back to TV reception by pressing the
TV/TEXT/MIX button.
button.
in, the word “NEWS
p, ~:;;
(Normal TV picture)
/ 4 “a ‘:
I
(5) Press the TV/TEXT/MIX
button.
I
EKao
Note: It is not possible to select another TV station
,6
P500
SPORT NEWS
599 501 510 600
(TEXT mode)
p500 .......... ~..
#
q
u
s~ ; +,,&/s
“w
599 501 510 600
■ Updated Page
There are pages which are updated as events progress, such as sports results, news reports and traffic information.
If you have selected one of the above pages from the list of contents and you want to view television but still be kept
informed about the other events;
P300
Updated Page
399 301 310 400
(TEXT mode)
button.
“-* (1) Press the Digit
q
A
P300
Updated Page
(x) (?) S****
(TEXT mode)
*@g
(3) As soon as this page is
q~(;:, ~~~
(Normal TV picture)
I
J
(Normal TV picture)
man
d
(4) Press the TVflEXT/MIX
button.
Note: It is not possible to select another TV station
during an UP - DATE. You should first switch
~
back to TV reception by pressing the TVl
TEXT/MIX button.
m
(TEXT mode)
■ TIME x~
If the time is required while a programme is being viewed, press
the TIME/SUB x~ button.
Providing that the channel being viewed is also transmitting
teletext, the time will appear at the top righthand of the screen
for five seconds. The digits displayed represent
hours/minutes/seconds.
TIME/SUB
(Normal TV picture)
I
■ FLOF (FLOF: Full -level -one feature)
When a broadcasting station provides FLOF service, you can access the text pages you desire quickly and easily.
In the FLOF mode , four Fastext topics are displayed at the bottom of the screen. These can be selected by pressing the
corresponding coloured button(Red, Green, Yellow, Cyan) on the remote control transmitter.
For example, when the Red button is pressed, the topic written in red is selected.
To get back to the initial index page, press the INDEX button.
(FLOF mode)
I
TEXT INDEX
I
News Travel TV Weather
I
e.g. To select the NEWS
f
I
page, press the RED key.
I
\ \
n\\
*@J *
Red Green
Yellow Cyan
NEWS
News Sport
City
Travel
I
\ \
Red
G~een
Yellow Cyan
9 Non FLOF Service
When the station does not have FLOF service, the INDEX page(Pl 00) is automatically displayed.
At the bottom of the screen, the four page numbers 199,101,110,200 are also displayed. Then, when you select a
random page number out of the displayed four pages by pressing a colour button, the text of that page is displayed.
Of course at any time you can select new pages by inputting new numbers.
(Non FLOF mode)
PI 00
TEXT INDEX
Red Green
Yellow
Cyan
e.g. To select pagel Ol,
press the GREEN key.
*
(
/
(Selected page)
r
PI01
TEXT (Pagel 01)
100
102
[
Green ~ [~) [~]
......
:101:+1=102
{Pa~e 102 is ../
Omit
(Sele&ted page)
..t ....
/100!+10=110
..........
f
\
Page 110 is
Note:
displayed.
Ifyour aerial signal is poor, the teletext reception maybe poor.
Omit
&
1~~~(Selected
1
page)
:i-oo+l 00=200
.........
Page 200 is
displayed.
To restrict programme positions that you do not want others to watch.
Any positions can be restricted.
How to Set Restrictions
For exampie, to restrict programme position “15”.
~ Select programme position “15”.
I
I
u
15
•1
2
Press and hoid the RECALL/COLOUR SYSTEM @ button for more than 2 seconds.
The programme number” 15” wiii move to
the center of the screen.
❑
3 Press the FUNCTiON @ button.
P~
sYsllEM I
-A +
vPA
m
The picture wiii disappear, and” X 15” wiil
be displayed on the screen.
,
●
The restricted setting is now completed.
Watching a TV programme that has been restricted
To watcha TV programmethat
has been restricted.
c1
1 Seiect the restricted position (position” 15 “).
m
❑
3 Press the RECALL/COLOUR SYSTEM @ button for watching a TV programme.
Note: The position” 15” is still in the
restricted position.
ti
Canceling of the Restriction
$
❑
2 Press and hold the RECALIJCOLOUR SYSTEM ~ button for more than 2 seconds.
— .
. .
#
m
The programme number and” X“ wiii move
to the center of the screen, and the picture
A
~
@
wiii appear.
J
To cancei the restriction
•1
1 Seiect the restricted position.
II
2 Press and hoid the RECALL/COLOUR SYSTEM ~ button for more than 2 seconds. The programme number
and” X“ wiii move to center of the screen, and the picture wiii appear.
c1
3
Press the FUNcTiON ~ button for canceiiing the restricted position, The” X 15” wiii disappear.
The canceiiing of the restriction is compiete.
It is possible to set the maximum sound volume at your preference and suppresses the channel tuning function,
so that even if the MEMORY/PRESET button is pressed, the channel tuning mode (preset mode) will remain
inactive.
(
Setting procedure
❑
I Set the desirable volume level using the LEVEL ~ button.
.
............... ............
................ ............
@ LEVEL
❑
2
[Iuu
Ull
4 SOUND
111111 ---------
The volume level set in this
procedure will be memorized
as the maximum volume level.
Press and hold the FUNCTION ~ button on the front control panel of the TV set, then press the
RECALL/COLOUR SYSTEM @ button on the remote control transmitter.
v k FUNCTION
P3?ft
Uu-uu
660- “o
,.,.,.,,
.................
;.
........
RECALL/
.........
,.,.:
:.:.
.....
..,.
.......
COLOUR
wwww*:*.... ““’””
,.,.,.,.,.,
SYSTEM
..............
:~” “z
❑
3 Select”1”, by pressing LEVEL( + or – ) @ button.
@ COLOUR
11111111111 ----
ITEM-1 SET + O
etc.
ITEM-1 SET+ 1
r
~ press the RECALUCOLOUR SYSTEM G button to return to the normal TV mode.
u
Canceling procedure
II
1
Press and hold the FUNCTION @ button on the front control panel of the TV set, then press the
RECALL/COLOUR SYSTEM ~ button on the remote control transmitter.
ITEM-1
SET+ 1
r
1 I
❑
2 Select “O”, by pressing LEVEL( + or - ) @ button.
ITEM-1
SET + O
r
3 Press the RECALUCOLOUR SYSTEM @ button to return to the normal TV mode.
mu
Connecting to the AV Input Jacks
Connect the video and audio outputs of a VCR, video disc player, etc.
to the input jacks of this TV set. Tapes and discs can be played back.
AV Terminal (Rearofthe Set)
u
OUT
AV1
IN
??=&
to the Video Output
~ @l/-
- @== ‘o=utput
To watch the video input picture
(1) Press the TV/AV Selector@.
J!-1”4
(2) Set the VCR to playback mode.
To return to the TV mode;
Press the lVIAV Selector again.
-0
TVIAV
Selector
VCR for piayback
-
Video
Camera
e.t.c.
if necessary, seiect the coiour system to match the appropriate
AV equipment.
Each time the COLOUR SYSTEM ~ or @ button is pressed,
colour system changes as foiiows;
&or&
+!N-”4”3
ColourSystem
I
Colour system setting for AV mode is automatically
stored in the memory.
Note: Pressing either of the Programme UP/DOWN buttons on the remote control or the TV will return the TV
to TV mode.
You can select a TV programme while watching a playback from a VCR
For example:
. To seiect the programme position “9” while watching a playback from external VCR, press “9” button of the remote
control. The TV set return to the TV mode and programme “9” wiii be selected.
I
● To Seiect the programme position “26”, press “--
/-”
button, “2” then “6” button. The lV set return to the TV mode
and programme “26” wiil be selected.
~
I
Connecting to the AV Output Jacks
n
OUT
AVI
IN
m
\
Recording TV broadcasts
Lk
to
the Video input
() @
VCR for recording
to the Audio Input
The AV output terminai provides audio and video output for lV broadcasts being received. They are used to
record lV broadcasts.
I
To record a
TV broadcast while watching the playback from a VCR
I
Recording TV broadcasts
-
to the AudioIntput
to the VideoOutput
zp~~=
9
3
r-
to
the Video Intput
-?
to
the AudioOutput
nr
VCR for recording
VCR for piayback
Example: To record a TV broadcast of the programme position “ 7 “ while
watching the playback from a VCR,
(1) Seiect the programme position “7”.
7
(2) Set the TV receiver to the AV mode to watch the piayback from a VCR.
AV
(3) Set the VCR for recording to the recording mode.
AV Connection to the Aerial Socket
The AV apparatus can aiso be connected to the aeriai socket of your lV receiver.
Presetting to watch the video input
(1) Piay back the VCR.
(2) Tune a channei in programme position O(See Semi-auto tuning & Manuai tuning on page 11).
Watching the video input
Seiect programme position O.
ANT. 75 Q
‘El
o
Aeriai socket
kii=i=d
VCR
m
t
For further details concerning this connection and adjustment, refer to the operating instructions for the
AV equipment.
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
Other documents
-
Panasonic TX25W3 User manual
-
-
-
-
-
Sharp 54GS-61S User manual
-
Panasonic TX20LB5FG Operating instructions
-
Panasonic TX20LB5PG Operating instructions
-
Panasonic TX20LA60F Operating instructions
-
Panasonic TX20LA6P Operating instructions