Contec GPD-U64EM-DC2 NEW Owner's manual
- Category
- TVs & monitors
- Type
- Owner's manual
This manual is also suitable for
Product Guid
e
FLAT PANEL DISPLAY 19-inch
GPD-U64EM-DC2
Thank you for purchasing this product. The product you have purchased consists of the
following items.
Check, with the following list, that your package is complete.
If you find any item either missing or damaged, please contact the sales representative you
purchased the product from.
1. About the Product
This product is a 19-inch On-Screen Display with a high-performance touch screen.
As an indicator you can touch the screen with your finger and operate like a tablet PC, this
product can be used to control production lines, provide work instructions, manage access,
in addition to operate industrial devices through the screen.
2. Product Configuration
This product consists of the items listed below.
Check, with the following list, that your package is complete. If you discover damaged or
missing items, contact your retailer.
Product…1 Product Guide
(this sheet)…1
Warranty Certificate…1
USB Cable For Touch
Screen 1.8m (A – B t
y
pe)
…1
VGA Cable 1.8m…1
3. Safety Precautions
This document provides safety information using the following symbols to prevent
accidents resulting in injury or death and the destruction of equipment and resources.
Understand the meanings of these labels to operate the equipment safely.
DANGER
DANGER indicates an imminently hazardous situation
which, if not avoided, will result in death or serious
injury.
WARNING
WARNING indicates a potentially hazardous situation
which, if not avoided, could result in death or serious
injury.
CAUTION
CAUTION indicates a potentially hazardous situation
which, if not avoided, may result in minor or moderate
injury or in property damage.
Handling Precautions
WARNING
Always check that the power supply is turned off before connecting or disconnecting
power cables.
This product is not intended for use in aerospace, space, nuclear power, medical
equipment, or other applications that require a very high level of reliability. Do not use
the product in such applications.
If using this product in applications where safety is critical such as in railways, automotive,
or disaster prevention or security systems, please contact your retailer.
Do not perform keypad operations on the touch screen that may threaten human life or
serious damage. Please design a system that can deal with incorrect key input operations.
CAUTION
Do not use or store this product in a location exposed to high or low temperature that
exceeds range of specification or susceptible to rapid temperature changes.
Example: Exposure to direct sun In the vicinity of a heat source
Do not use this product in extremely humid or dusty locations. It is extremely dangerous
to use this product with its interior penetrated by water or any other fluid or conductive
dust. If this product must be used in such an environment, install it on a dust-proof
control panel, for example.
Avoid using or storing this product in locations subject to shock or vibration that exceeds
range of specification.
Do not use this product in the vicinity of devices that generate strong magnetic force or
noise. Such products will cause this product to malfunction.
Do not use or store this product in the presence of chemicals.
To clean this product, wipe it gently with a soft cloth dampened with either water or mild
detergent. Do not use chemicals or a volatile solvent, such as benzene, thinner,
ammonia, or a strong chlorinated solvent to prevent pealing or discoloration of the paint.
This product’s case may become hot. To avoid being burned, do not touch that section
while this product is in operation or immediately after turning off the power. Avoid
installation in a location where people may come into contact with that section.
In the event of failure or abnormality (foul smells or excessive heat generation), unplug
the power cord immediately and contact your retailer.
Do not use any sharp-pointed object such as a mechanical pencil to touch the touch
panel. Doing so may scratch the touch panel, resulting in malfunctions.
Do not subject the touch screen to shock as doing so may break it.
Use your fingers to perform operations on the touch screen.
Operations with the stylus pen on the touch screen might not perform well due to the
pen you are using with.
LCD may have a few bright spots that are always on or a few black spots that are always
off. Color irregularity may also occur depending on the viewing angle. This however is
due to the structural characteristics of the LCD; therefore, it is not a product fault.
As a characteristic feature of the capacitive touch screen, the sensor may become
unstable due to the influence of surrounding metal or electrically floating metal objects,
and this might lead to shifting the detection position. In this case, perform calibration
again for the touch-panel screen to reset the calibration data.
The backlight of the touch screen and the display have limited lifetime. Therefore, that
they need to be inspected regularly.
- The lifetime of the consumable parts
Backlight --- Display brightness decreases over time with use.
If the luminance setting is 100 and the ambient temperature is 40 ° C, the brightness
drops to 50% in 30,000-hour use.
* For expendables replacement, contact your retailer as it must be performed as
a process of repair (there will be a charge).
- LCD faults
LCD may have a few bright spots that are always on or a few black spots that are
always off below a certain standard. This however is due to the structural
characteristics of the LCD; therefore, it is not a product fault.
Standard :
The number of bright spots≤2, The number of two consecutive bright spots ≤
1, The total number of bright spots≤2, The distance between two bright spots
≥15mm
The number of black spots ≤5, The number of two consecutive black spots ≤2,
The total number of black spots ≤5, The distance between two black spots ≤
15mm
The number of bright and black spots ≤5, Bright and black spots on the line :
Non-enterable
- Burn-in on TFT Display
“Burn-in” may occur if the same display is retained for a long time. Avoid this by
periodically switching the display so that the same display is not maintained for a
long time.
* Burn-In : Phenomenon characterized by a TFT display as a result of long-time
display of the same screen where a shadow-like trace persists because electric
charge remains in the LCD element even after the patterns are changed.
- About MTBF
50323 Hrs
VCCI Class B Notice
この装置は、クラスB機器です。この装置は、住宅環境で使⽤することを⽬的としてい
ますが、この装置がラジオやテレビジョン受信機に近接して使⽤されると、受信障害
を引き起こすことがあります。
取扱説明書に従って正しい取り扱いをしてください。
VCCI-B
FCC PART 15 Class B Notice
NOTE
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed
to provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television recep-
tion, which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the following
measures:
-- Reorient or relocate the receiving antenna.
-- Increase the separation between the equipment and receiver.
-- Connect the equipment into an outlet on a circuit different from that to which
the receiver is connected.
-- Consult the dealer or an experienced radio/TV technician for help.
FCC WARNING
Changes or modifications not expressly approved by the party responsible for
compliance could void the user's authority to operate the equipment.
4. Product Nomenclature and
Function
Nomenclature of Product Components
<Front>
<Rear>
<Bottom>
Description of Product Components
<Power Supply Terminal >
When connecting the power line with the power supply terminal, ensure to align them with
the proper polarities.
Reverse polarities can result in damages to the product.
Pin Description
1 +24V
2 GND
3 FG
Maker : DECA Model : T55-O-03
* For the FG terminal, connect FG cable. It is conducted with ground (GND) signal.
If you lost cable fixing screws, get a screw within 4 mm thread length.
<VGA Connector>
This product has a connector for display connections. The connector name is VGA (15-pin
HD-SUB).
Use the bundled display cable to connect this with the PC.
Connector t
y
pe 15-pin HD-SUB (FEMALE)
Pin number Si
g
nal name Pin number Si
g
nal name
1 Red video signal input 9
+5V: Input from host system
for the VESA DDC2B function
2 Green video si
g
nal input 10 Si
g
nal
g
round
3 Blue video si
g
nal input 11 N.C.
4 N.C. 12
SDA signal input for the VESA
DDC2B function
5
DDC ground for the VESA
DDC2B function
13
Horizontal signal input from
host s
y
stem
6
Analog signal ground for the red
video
14
Vertical signal input from host
s
y
stem
7
Analog signal ground for the
g
reen video
15 DDCCLK
8
Analog signal ground for the
blue video
<DVI-D Connector>
This product has a connector for DVI-D connections.
The bundled display cable cannot be used for this.
Connector t
y
pe DVI-D connector 24-pin (FEMALE)
Pin
num-
ber
Signal name Pin
num-
ber
Signal name Pin
num-
ber
Signal name
1 TMDS DATA2- 11
TMDS Data 1
/
3
Shield
21 TMDS DATA5+
2 TMDS DATA2+ 12 TMDS DATA3- 22 TMDS Clock Shield
3
TMDS Data 2/4
Shield
13 TMDS DATA3+ 23 TMDS Clock+
4 TMDS DATA4- 14 +5V DDC Power 24 TMDS Clock-
5 TMDS DATA4+ 15
GND (+5V, Analog
V/H S
y
nc)
6 DDC Clock 16 Hot Plu
g
Detect
7 DDC Data 17 TMDS DATA0-
8 NC 18 TMDS DATA0+
9 TMDS DATA1- 19
TMDS Data 0/5
Shield
10 TMDS DATA1+ 20 TMDS DATA5-
<USB Connector>
This product has a connector (TYPE-B) for a touch screen. Use the bundled USB cable for
touch screen to connect this with the PC.
(One side of the display cable is already connected to the display section upon shipping.
Connect the other end of the cable to the USB connector on the PC.)
Pin number Si
g
nal name
1 +5V (INPUT)
2 DATA-
3 DATA+
4 GND
<RJ-11 Connector>
This connector is not used for the product.
CONTEC CO.
,
LTD.
3-9-31
,
Himesato
,
Nishi
y
odo
g
awa-ku
,
Osaka 555-0025
,
Ja
p
an
http://www.contec.com
/
No part of this document may be copied or reproduced in any form by any means
without prior written consent of CONTEC CO., LTD.
NA07080 (LYXQ982) 06152020_rev2 [01062020] June 2020 Edition
5. Before Using the Product for
the First Time
Follow the next steps to set up this product.
STEP1 Set up and connect the display product.
STEP2 Connect cables.
Connect the cable of necessary external devices, such as keyboard, to this
product using appropriate cables.
STEP3 Turn on the power.
After verifying that you have correctly followed steps 1 and 2, turn on the
power. If you find any abnormality after turning on the power, turn it off and
check to see if the setup has been performed properly.
CAUTION
When connecting the power line with the power supply terminal, ensure to align them
with the proper polarities.
Before turning the power on for the first time, be sure to connect the PC section with the
cable for the display and USB cable for the touch screen which are connected to the
display.
Be sure to connect the display before turning the power on. Connecting the display after
turning the power on may prevent it from being displayed properly.
6. Display Setting Menu
To set the display, use the buttons on the back side of the display as shown below.
OSD
Button
Menu OFF state Menu ON state
MENU Menu screen
Menu hidden/
Go back to Main menu
▲ Brightness
The menu item will be moved up /
Increase values
▼ Contrast
The menu item will be moved down
/
Decrease values
SELECT Set / Select Sub-items
Power ON/OFF
1. Press the "MENU" button to open the main menu.
Press the "▲" or "▼" button to select the item in the menu.
2. Press the "Select" button to adjust the specified item.
3. Press the "▲" or "▼" button to adjust the value of the specified item.
4. Press the "MENU" button to go back to the main menu, or finish the OSD.
5. If the idle state continues for the set time, the OSD will automatically finish.
6. To lock the OSD/Power menu button, follow the next instruction.
(Note: The monitor must be turned on with enabled signal connection).
a. Press the "MENU" button to open the main menu.
b. Keep pressing down the "MENU" button in the menu to finish the OSD.
Then, while pressing down the "MENU" button, press the "POWER" button.
The "LOCK/Unlock" menu appears for three seconds.
c. Select the OSD or Power setting by using the "SELECT" button, and press the
"▲" or "▼" button to set the "LOCK".
d. When you release the "▲" or "▼" button, the previous settings are saved and
the "LOCK/Unlock" menu will be automatically finished.
7. To unlock the OSD/Power menu button, follow the next instruction.
(Note: The monitor must be turned on with enabled signal connection).
a. While pressing down the "MENU" button, press the "POWER" button.
The "LOCK/Unlock" menu appears for three seconds.
b. Select the OSD or Power setting by using the "SELECT" button, and press the
"▲" or "▼" button to set the "UNLOCK".
c. When you release the "▲" or "▼" button, the previous settings are saved and
the "LOCK/Unlock" menu will be automatically finished.
CAUTION
When the lock function for OSD is selected, all buttons except the "POWER" button are
disabled.
When the lock function for the power is selected, the "POWER" button is disabled.
Therefore, a user is unable to turn off the monitor by pressing the "POWER" button.
Menu Description
Items Description Defaults
Contrast This adjusts the brightness of the monitor. 50
Brightness This adjusts the back light level of the monitor. 100
Auto Adjust
This automatically sets images to be displayed in
full-screen size.
N.A.
Left / Right This adjusts the position of the screen horizontally. N.A.
Up/ Down This adjusts the position of the screen vertically. N.A.
Horizontal size This adjust the horizontal dot clock on the screen. N.A.
Fine This adjust the pixel positions on the screen. N.A.
OSD Left / Right This adjusts the position of the OSD menu horizontally. 50
OSD Up / Down This adjusts the position of the OSD menu vertically. 50
OSD Time out
This adjusts the length of time to display the setting
screen automaticall
y
.
15
OSD Language
This selects the language to be displayed on the OSD
menu.
(English, French, Japanese, German, Spanish, Italian,
Chinese (Traditional and Simplified))
English
Factory Reset This restores the factory settings. N.A.
RGB
This adjusts color temperature.
(9300K, 6500K, 5500K, 7500K, User)
User
7. Specifications
Function Specifications
Item Description
Displa
y
Specifications
Panel t
y
pe 19-inch non-
g
lare treatment TN panel
Resolution (max) 1,280 x 1,024
Contrast ratio 1000 : 1
Luminance (Back li
g
ht t
y
pe) 225 nits (Pro
j
ected capacitive)
View an
g
le H:170°, V:160°
Touch screen specifications
Touch screen Pro
j
ected capacitive
T
ouch points 10
Touch screen interface USB-HID (T
y
pe B)
I/O port
USB port 1 x USB 2.0 (Type B)
For Touch screen interface (USB = HID)
Video port 1 x VGA (15-pin HD-SUB), 1 x DVI
Audio port N.A.
P
ower input 24VDC±10%, 3 terminals (with covers)
Other
Compatible OS Windows10 IoT Enterprise
Chassis color Black (Back
g
round color : Black)
Structure Glass, metal
Dust-proof, Drip-proof Displa
y
front side IP65
Ph
y
sical dimensions (mm) 416.0(W) x 344.0(H) x 46.6(D)
Wei
g
ht 4.4 k
g
VESA 100 x 100 mm
Power consumption 20W (Typ.) (24VDC, 0.83A)
25W (Max.) (24VDC, 1.04A)
Environment Specifications
Item Description
Operating temperature 0 - +40°C
Operating Humidity 20 - 80%RH (No condensation)
Non-operating ambient tempera-
ture
-20 - +60°C
Non-operating ambient humidity 10 - 90%RH (No condensation)
Floating dust particles Not to be excessive
Corrosive gases None
Vibration
re-
sistance
Sine wave vibration 0.25G 0 to Peak, 10 to 500Hz, 0.25 octave / minute sweep rate.
This requires one sweep of 10 to 500 to 10 Hz for each of
the three axes
Random
vibration
0.002 G2 / Hz, 10 to 500Hz, nominal 1.0 Grms.
The test should be 30- minute-lon
g
for each axis
Shock
re-
sistance
Half-sine shock 30G-peak acceleration 2 milliseconds duration 3 axes each
The number of shock inputs in each direction should be
sufficient so that the performance of the monitor can be
evaluated
Square wave shock 50G peak acceleration, 180 inches / second velocity
change.
Once for each axis, the total of 6 shock inputs
Standard
VCCI Class B, FCC Class B,
CE Marking (EMC Directive Class A, RoHS Directive) *1,
CCC
Regulation RoHS Directive (includes the bundled cables)
*1 In order to suit CE standards, DVI cable length uses a thing of 3 m or less.
8. Physical Dimensions
-
1
-
2
Contec GPD-U64EM-DC2 NEW Owner's manual
- Category
- TVs & monitors
- Type
- Owner's manual
- This manual is also suitable for
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI