JUNG 20320REG is a power supply device designed for use with KNX systems. It provides a reliable power source for KNX devices and offers several useful features.
The device is equipped with multiple outputs, allowing you to connect and power multiple devices simultaneously. The total load of the outputs can be subdivided as desired, ensuring efficient power distribution.
JUNG 20320REG includes several LED indicators to provide visual feedback on the device's status. The green LED indicates normal operation, while the red LED signals an overload or short circuit on the KNX bus line or output DC 30 V. The yellow LED indicates overvoltage on the KNX bus line or output DC 30 V.
JUNG 20320REG is a power supply device designed for use with KNX systems. It provides a reliable power source for KNX devices and offers several useful features.
The device is equipped with multiple outputs, allowing you to connect and power multiple devices simultaneously. The total load of the outputs can be subdivided as desired, ensuring efficient power distribution.
JUNG 20320REG includes several LED indicators to provide visual feedback on the device's status. The green LED indicates normal operation, while the red LED signals an overload or short circuit on the KNX bus line or output DC 30 V. The yellow LED indicates overvoltage on the KNX bus line or output DC 30 V.
Power supplies
Power supply 160 mA
Art. no.: 20160REG
Power supply 320 mA
Art. no.: 20320REG
Power supply 640 mA
Art. no.: 20640REG
Power supply 1280 mA
Art. no.: 21280REG
Operating instructions
1 Safety instructions
Electrical devices may only be mounted and connected by electrically skilled persons.
Serious injuries, fire or property damage possible. Please read and follow manual fully.
Danger of electric shock. During installation and cable routing, comply with the regulations and
standards which apply for SELV circuits.
These instructions are an integral part of the product, and must remain with the end customer.
2 Device components
Figure1: View
1 / 8
82597333 28.01.2020
j0082597333
Power supplies
Figure2: 1280 mA power supply – view
(1) Connection of mains
(2) LED
Betrieb
, green
On: Normal operation
Flashes: Overload or overvoltage
Off: No mains voltage or internal error
(3) LED
Überlast
, red
On: Overload or short-circuit on KNX bus line or output
DC 30 V
(4) LED
Überspannung
, yellow
On: Overvoltage on KNX bus line or output
DC 30 V
(5) Output
DC 30 V
(6) Output
Bus
for KNX bus line
(7) LED
Reset
, red
Flashes rapidly 2.5 Hz: Reset for 20 seconds
Flashes slowly 0.25 Hz: Permanent reset
(8) Button
Reset
Acknowledge the diagnostic message: Press briefly, < 0.5 seconds
Switch off the KNX bus line for 20 seconds: Press between 2...4 seconds
Permanently switch off the KNX bus line: Press longer than 4 seconds
Terminate the permanent reset: Press the button
(9) Signal contact for diagnostic message
Closed: Normal operation
Open: After overload, overvoltage or in case of a KNX power failure
3 Function
System information
This device is a product of the KNX system and complies with the KNX directives. Detailed tech-
nical knowledge obtained in KNX training courses is a prerequisite to proper understanding.
Intended use
– Supplying KNX devices with bus voltage
– Supplying devices with direct current
– Mounting on DIN rail according to EN 60715 in sub-distribution unit
Product characteristics
– Output with integrated inductance for supplying KNX bus lines
– DC 30 V output for supplying additional devices
2 / 8
82597333 28.01.2020
j0082597333
Power supplies
– Nominal current can be subdivided to outputs as desired
– Reset button
– Short-circuit proof
– Overvoltage proof
– No-load proof
– Suitable for operation in systems with emergency power supply
– Potential-free signal contact for operating and diagnostic message
– Two identical power supplies can be connected in parallel (with the versions 160 mA, 320
mA and 640 mA)
4 Operation
Acknowledging the diagnostic message
After detecting a overvoltage or a short circuit the LED and the signal contact signal the event
until the message is acknowledged.
￭ Press the Reset button for less than 0.5 seconds.
LED functions and signal contact
LED
Betrieb
(2),
green
LED
Überlast
(3),
red
LED
Überspannung
(4), yellow
LED
Reset
(7), red
Signal con-
tact (9)
Normal oper-
ation
on off off off closed
Reset for
20 seconds
on off off flashes
2.5 Hz
closed
Permanent
reset
on off off flashes
0.25 Hz
closed
Overvoltage flashes
0.5 Hz
off on (until the
message is ac-
knowledged)
off open (until
the message
is acknow-
ledged)
Overload,
short-circuit
flashes
0.5 Hz
on (until the
message is ac-
knowledged)
off off open (until
the message
is acknow-
ledged)
KNX voltage
failed / in-
ternal error
off off off off open
In normal operation the control of the power supply is not necessary. The button (8) is recessed
and thus prevents that it is inadvertently actuated in operation.
Reset function and Reset button
When resetting a bus segment, the output voltage of the power supply is switched off. At the
same time the bus line is short-circuited so that all connected bus devices are disconnected
from the bus voltage.
Resetting the bus line for 20 seconds
￭ Press the
Reset
button (8) between 2 ... 4 seconds.
The bus line is short-circuited for 20 seconds.
The LED
Reset
(7) flashes quickly.
After 20 seconds the bus voltage is switched on again and the LED
Reset
switches off.
3 / 8
82597333 28.01.2020
j0082597333
Power supplies
Permanently resetting the bus line
￭ Press the
Reset
button (8) for more than 4 seconds.
The bus line is short-circuited.
The LED
Reset
(7) flashes slowly.
Terminating the permanent reset
Prerequisite: The bus line is permanently reset, the LED
Reset
(7) flashes slowly.
￭ Press the
Reset
button (8).
The bus voltage is switched on again and the LED
Reset
switches off.
5 Information for electrically skilled persons
DANGER!
Mortal danger of electric shock.
Disconnect the device. Cover up live parts.
5.1 Fitting and electrical connection
DANGER!
Electrical shock when live parts are touched.
Electrical shocks can be fatal.
Before working on the device, disconnect the power supply and cover up live parts
in the working environment.
Fitting the device
Observe the temperature range. Ensure sufficient cooling.
￭ Mount the device on DIN rail. The terminals for the mains connection (1) must be at the
top.
4 / 8
82597333 28.01.2020
j0082597333
Power supplies
Connecting the device to mains voltage and bus
Figure3: Wiring example – mains voltage and bus line
Figure4: Clampable conductor cross-section
￭ Connect the mains voltage to the terminals
L
and
N
(1).
￭ Connect the protective conductor
PE
to the terminal Ʈ.
￭ Connect the KNX bus line to output
Bus
(6).
￭ Install the cover to protect the bus connection against hazardous voltages in the connec-
tion area.
The total load of the outputs can be subdivided as desired. Do not exceed the total rated
current.
Do not connect any other products to the bus output. This might influence the bus com-
munication.
If required, an identical power supply can be connected in parallel for the device variants
160, 320 and 640 mA.
Connecting the diagnostic analyser
The power supply signals KNX voltage failure, overvoltage, overload and short circuit using a
potential-free contact (9). A monitoring device can detect the switching status and forward it for
diagnostic purposes.
5 / 8
82597333 28.01.2020
j0082597333
Power supplies
The signal output serves only for signalling purposes and may not be used as a load out-
put.
A signal lamp, a signal relay or, e.g., a KNX binary input connected to a KNX bus line can be
used as monitoring device.
￭ Connect the signalling device according to the connection example (Figure 5).
L N
L
N
PE
max. 2 A
Figure5: Application example – signal lamp for optical operating display
￭ Connect the KNX binary input according to the connection example (Figure 6).
Figure6: Application example – KNX binary input on main line for detecting and centrally sig-
nalling diagnostic messages
Observe the wiring! Install the cables for the signal contact such that no loops are cre-
ated. During operation loops can cause interference voltages to be coupled into.
6 / 8
82597333 28.01.2020
j0082597333
Power supplies
The signal contact indicates a power failure on the KNX line. When power supplies are
connected in parallel, the signaling contact opens only if both power supplies are faulty or
switched off (eg due to failure of the mains voltage on both devices).
In this case too, the green operation LED will not extinguish until both power supplies are
switched off.
Operation with emergency power systems
The power supply can be used in combination with centrally supplied emergency power sys-
tems. In this way, the function of the KNX system and the control of the most important func-
tions can be ensured in emergency operation.
Statutory and standard specifications for emergency power and emergency lighting sys-
tems vary from country to country. In any event, the user / technical planner must check
whether the specific specifications are observed.
Cable lengths
For KNX line segments and power supplies the following rules apply:
– Bus line length per lin segment: Max. 1000 m
– Bus line length between power supply and KNX bus subscriber: Max. 350 m
– Bus line length between two KNX bus subscribers: Max. 700 m
6 Technical data
Rated voltage AC 220 ... 240 V~
The device is operable in the range of 180 V
AC … 264 V AC.
Mains frequency 50 / 60 Hz
Power loss (max. load on all outputs)
Art. no. 20160REG max. 1.5 W
Art. no. 20320REG max. 1.8 W
Art. no. 20640REG max. 2.9 W
Art. no. 21280REG max. 6.4 W
Efficiency
Art. no. 20160REG approx. 76%
Art. no. 20320REG approx. 84%
Art. no. 20640REG approx. 87%
Art. no. 21280REG approx. 86%
Rated voltage DC DC 240...250 V
KNX
KNX medium TP256
Bus output voltage DC 28 ... 31 V SELV
Output current
Art. no. 20160REG 160 mA (all outputs)
Art. no. 20320REG 320 mA (all outputs)
Art. no. 20640REG 640 mA (all outputs)
Art. no. 21280REG 1280 mA (all outputs)
Short-circuit current
Art. no. 20160REG max. 1 A
Art. no. 20320REG max. 1 A
Art. no. 20640REG max. 1.5 A
Art. no. 21280REG max. 3 A
7 / 8
82597333 28.01.2020
j0082597333
Power supplies
Connection type for bus device connection terminal
Parallel operation with identical power supply
Art. no. 20160REG Yes
Art. no. 20320REG Yes
Art. no. 20640REG Yes
Art. no. 21280REG No
Output DC 30 V
Output voltage DC 30 V
Signal output
Switching voltage AC AC 12 ... 230 V~
Switching voltage DC DC 2 ... 30 V
Switching current 5 mA ... 2 A
Ambient temperature -5 ... +45 °C
Storage/transport temperature -25 ... +70 °C
Relative humidity max. 93 % (no condensation)
Fitting width
Art. no. 20160REG 72 mm / 4 module
Art. no. 20320REG 72 mm / 4 module
Art. no. 20640REG 72 mm / 4 module
Art. no. 21280REG 108 mm / 6 module
Connection mode device connection terminal
Finely stranded with conductor sleeve 0.5 ... 2.5 mm²
7 Warranty
The warranty is provided in accordance with statutory requirements via the specialist trade.
ALBRECHT JUNG GMBH & CO. KG
Volmestraße 1
58579 Schalksmühle
GERMANY
Telefon: +49 2355 806-0
Telefax: +49 2355 806-204
www.jung.de
8 / 8
82597333 28.01.2020
j0082597333
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
JUNG 20320REG Operating instructions
- Type
- Operating instructions
JUNG 20320REG is a power supply device designed for use with KNX systems. It provides a reliable power source for KNX devices and offers several useful features.
The device is equipped with multiple outputs, allowing you to connect and power multiple devices simultaneously. The total load of the outputs can be subdivided as desired, ensuring efficient power distribution.
JUNG 20320REG includes several LED indicators to provide visual feedback on the device's status. The green LED indicates normal operation, while the red LED signals an overload or short circuit on the KNX bus line or output DC 30 V. The yellow LED indicates overvoltage on the KNX bus line or output DC 30 V.
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
-
JUNG LEDKO6TX24 Operating instructions
-
-
-
-
-
-
-
-
-
JUNG 230241SR Operating instructions
Other documents
-
Rutenbeck 221012 Datasheet
-
iGuzzini MI57 Installation guide
-
-
-
ABB SV/S 30.160.1.1 User manual
-
WAGO KNX IP Programmable Fieldbus Controller User manual
-
Gira 2120 00 Operating Instructions Manual
-
-
-