Pittsburgh 56621 Owner's manual

Type
Owner's manual

This manual is also suitable for

Pittsburgh Item 56621 is a 3-ton (6,000 lb.) capacity floor jack that can lift vehicles up to 18-1/4" high. It features a sturdy steel frame, a hydraulic lifting mechanism, and a wide base for stability. The jack is ideal for use in garages, workshops, and other automotive environments.

Some of the key features of the Pittsburgh Item 56621 floor jack include:

  • 3-ton (6,000 lb.) capacity: The jack can safely lift vehicles weighing up to 6,000 pounds, making it suitable for most cars, trucks, and SUVs.
  • 18-1/4" maximum height: The jack can lift vehicles up to 18-1/4" high, providing ample clearance for most maintenance and repair tasks.

Pittsburgh Item 56621 is a 3-ton (6,000 lb.) capacity floor jack that can lift vehicles up to 18-1/4" high. It features a sturdy steel frame, a hydraulic lifting mechanism, and a wide base for stability. The jack is ideal for use in garages, workshops, and other automotive environments.

Some of the key features of the Pittsburgh Item 56621 floor jack include:

  • 3-ton (6,000 lb.) capacity: The jack can safely lift vehicles weighing up to 6,000 pounds, making it suitable for most cars, trucks, and SUVs.
  • 18-1/4" maximum height: The jack can lift vehicles up to 18-1/4" high, providing ample clearance for most maintenance and repair tasks.
!"#"$%&'(%)*+#"$*%,$-%.$$/-00)))1.,(+&(2(*"3.$14&5
65,"7%&'(%$*4.8"4,7%#'//&($%,$-%/(&9'4$#'//&($:.,(+&(2(*"3.$14&5
;$*5 <==>?
Weight Capacity 3 Tons (6,000 lb.)
Maximum Height 18-1/4"
Minimum Height 5-1/8"
Owners Manual & Safety Instructions
Save This Manual Keep this manual for the safety warnings and precautions, assembly,
operating, inspection, maintenance and cleaning procedures. Write the product’s serial number in the
back of the manual near the assembly diagram (or month and year of purchase if product has no number).
Keep this manual and the receipt in a safe and dry place for future reference. 20c
When unpacking, make sure that the product is intact
and undamaged. If any parts are missing or broken,
please call 1-888-866-5797 as soon as possible.
Copyright
©
2019 by Harbor Freight Tools
®
. All rights reserved.
No portion of this manual or any artwork contained herein may be reproduced in
any shape or form without the express written consent of Harbor Freight Tools.
Diagrams within this manual may not be drawn proportionally. Due to continuing
improvements, actual product may differ slightly from the product described herein.
Tools required for assembly an d se rv ic e may n ot b e in cl uded.
Read this material before using this product.
Failure to do so can result in serious injury.
SAVE THIS MANUAL.
Page 2 @&(%$*4.8"4,7%A'*#$"&8#B%/7*,#*%4,77%?CDDDCD==C<EFE1 Item 56621
GH@6IJ KL6MHI;KN OH;NI6NHNP6G6IQL
I,+7*%&2%P&8$*8$#
Safety ........................................................................3
Setup .........................................................................4
Operation ...................................................................5
Maintenance ..............................................................7
Parts List and Assembly Diagram.............................10
Warranty ...................................................................12
RHMN;NS%GJOTKUG%HNV%V6@;N;I;KNG
This is the safety alert symbol. It is used to alert you to potential
personal injury hazards. Obey all safety messages that
follow this symbol to avoid possible injury or death.
Indicates a hazardous situation which, if not avoided,
will result in death or serious injury.
Indicates a hazardous situation which, if not avoided,
could result in death or serious injury.
Indicates a hazardous situation which, if not avoided,
could result in minor or moderate injury.
Addresses practices not related to personal injury.
Page 3@&(%$*4.8"4,7%A'*#$"&8#B%/7*,#*%4,77%?CDDDCD==C<EFE1Item 56621
GH@6IJKL6MHI;KNOH;NI6NHNP6 G6IQL
;OLKMIHNI%GH@6IJ%;N@KMOHI;KN
@7&&(%W,4X%G,2*$Y%R,(8"83#
1. Study, understand, and follow all instructions
before operating this device.
2. Do not exceed rated capacity.
3. Use only on hard, level surfaces.
4. Lifting device only. Immediately after lifting,
support the vehicle with appropriate means.
5. Do not move or dolly the vehicle while on the jack.
6. Failure to heed these markings may result in
personal injury and/or property damage.
7. Lift only areas of the vehicle as specified
by the vehicle manufacturer.
8. No alterations shall be made to this product.
9. Never work on, under or around a load
supported only by this device.
10. Do not adjust safety valve.
11. Wear ANSI-approved safety goggles and
heavy-duty work gloves during use.
12. Keep clear of load while lifting and lowering.
13. Lower load slowly.
14. Apply parking brake and chock
tires before lifting vehicle.
15. Lift vehicle only at manufacturer
recommended locations.
16. Inspect before every use; do not use
if parts are loose or damaged.
17. Do not use for aircraft purposes.
18. The warnings, precautions, and instructions
discussed in this manual cannot cover all
possible conditions and situations that may occur.
The operator must understand that common sense
and caution are factors, which cannot be built into
this product, but must be supplied by the operator.
19. The Handle socket may be held down by a clip
under tension. Wear ANSI-approved safety goggles
before freeing Handle socket. Remove clip carefully.
;OLKMIHNIZ%%T*2&(*%2"(#$%'#*-
Check hydraulic fluid level and fill to 1/4″ below
the fill port as needed as stated on page 5.
Thoroughly test the Jack for proper operation.
If it does not work properly, bleed air from its
hydraulic system as stated on page 5.
%GH!6%I[6G6%;NGIMQPI;KNG1
Page 4 @&(%$*4.8"4,7%A'*#$"&8#B%/7*,#*%4,77%?CDDDCD==C<EFE1 Item 56621
GH@6IJ KL6MHI;KN OH;NI6NHNP6G6IQL
G*$'/%C%T*2&(*%Q#*-
%M*,9%$.*%6NI;M6%;OLKMIHNI%GH@6IJ%;N@KMOHI;KN%#*4$"&8%,$%$.*%+*3"88"83%&2%$."#%
5,8',7%"847'9"83%,77%$*\$%'89*(%#'+.*,9"83#%$.*(*"8%+*2&(*%#*$%'/%&(%'#*%&2%$."#%/(&9'4$1
N&$*- For additional information regarding the parts listed in the following pages,
refer to Parts List and Assembly Diagram on page 10.
@'84$"&8#
QCW&"8$
[Y9(,'7"4%Q8"$%
@7'"9%@"77%L7'3
G,2*$Y%!,7]*%
P&]*(%%
VK%NKI%KL6N%%
KM%HVWQGI
G,997*
[,897*
[,897*%G&4X*$
U"2$%H(5
M*,(%P,#$*(
P&]*(%L7,$*
^(*5&]*%
$&%,44*##%
@"77%L7'3_
@(&8$
R.**7
G*$%G4(*)
@"3'(*%H%
Page 5@&(%$*4.8"4,7%A'*#$"&8#B%/7*,#*%4,77%?CDDDCD==C<EFE1Item 56621
GH@6IJKL6MHI;KNOH;NI6NHNP6 G6IQL
K/*(,$"83%;8#$('4$"&8#
%M*,9%$.*%6NI;M6%;OLKMIHNI%GH@6IJ%;N@KMOHI;KN%#*4$"&8%,$%$.*%+*3"88"83%&2%$."#%
5,8',7%"847'9"83%,77%$*\$%'89*(%#'+.*,9"83#%$.*(*"8%+*2&(*%#*$%'/%&(%'#*%&2%$."#%/(&9'4$1
I&&7%G*$%Q/
H$$,4."83%$.*%[,897*
PHQI;KNZ%I.*%[,897*%#&4X*$%5,Y%+*%.*79%
9&)8%+Y%,%47"/%'89*(%$*8#"&81%%R*,(%HNG;C
,//(&]*9%#,2*$Y%3&337*#%+*2&(*%2(**"83%
[,897*%#&4X*$1%%M*5&]*%47"/%4,(*2'77Y1%
1. Fasten the Upper Handle to the Lower Handle.
2. Loosen the Set Screw and insert the
assembled Handle into the Handle Socket.
3. Tighten the Set Screw.
T7**9"83
1. Turn handle counterclockwise
to open Release Valve.
2. Remove four screws holding on the Cover Plate.
3. Remove Oil Fill Plug and top off hydraulic oil.
4. Apply pressure to saddle and quickly
pump handle several times.
5. Check Oil Fill Hole again and top off
with hydraulic oil if necessary.
6. Replace the Oil Fill Plug and Cover Plate. Turn
handle clockwise to close Release Valve.
7. Test several times for proper operation
before attempting to lift a load.
H99"83%[Y9(,'7"4%@7'"9
8. Remove the Cover Plate.
9. Remove the Fluid Fill Plug.
10. Add high grade hydraulic fluid into the fill hole
slowly until the fluid reaches the top of the hole.
Note: Do not touch the Handle when
adding the hydraulic fluid.
11. Replace the Fill Plug and Cover Plate.
Page 6 @&(%$*4.8"4,7%A'*#$"&8#B%/7*,#*%4,77%?CDDDCD==C<EFE1 Item 56621
GH@6IJ KL6MHI;KN OH;NI6NHNP6G6IQL
S*8*(,7%K/*(,$"83%;8#$('4$"&8#
U"2$"83
L,(X%]*."47*%&8%,%27,$B%7*]*7B%#&7"9B%#'(2,4*%#,2*7Y%,),Y%2(&5%&84&5"83%$(,22"41%%I'(8%&22%$.*%]*."47*`#%*83"8*1%%
L7,4*%$.*%]*."47*`#%$(,8#5"##"&8%"8%aLHMbc%^"2%,'$&5,$"4_%&(%"8%"$#%7&)*#$%3*,(%^"2%5,8',7_1%%G*$%$.*%]*."47*`#%
*5*(3*84Y%+(,X*1%%I.*8B%4.&4X%$.*%).**7#%$.,$%,(*%8&$%+*"83%7"2$*91
1. Turn the Handle counterclockwise to open
the release valve and lower the Jack. Once
the Jack is fully lowered, turn the Handle
firmly clockwise to close the valve.
2. Carefully position the Saddle of the Jack under
the vehicle manufacturer’s recommended lifting
point. (See vehicle manufacturer’s owner’s
manual for location of frame lifting point.)
3. Pump the Handle until the top of the Jack’s Saddle
has nearly reached the vehicle lifting point. Position
the Saddle directly under the vehicle’s lifting point.
4. To lift the vehicle, pump the Handle of
the Jack. Use smooth, full strokes.
5. Once the vehicle is raised, slide a jack stand of
appropriate capacity (not included) under a proper
lifting point referred to in the vehicle owner’s
manual. Always use two jack stands. Position them
at the same point on each side of the vehicle.
RHMN;NSZ The rated capacity of jack stands is per
pair, not the individual capacities combined unless
specifically noted on the product by the jack stand
manufacturer. Do not exceed rated jack stand
capacity. Ensure that the vehicle support points
are fully seated in the saddle of both jack stands.
Use a matched pair of jack stands per vehicle to
support one end only. Failure to do so may result
in the load suddenly falling, which may cause
personal serious injury and/or property damage.
6. Center the vehicle’s lifting point(s) on the saddle of
the jack stand(s). Set the jack stand(s) to the same
height according to the manufacturer’s instructions,
making sure that they lock securely into position.
7. Slowly turn the Handle counterclockwise to open
the release valve and lower the vehicle onto the
saddle(s) of the jack stand(s). Then, turn the
Handle firmly clockwise to close the valve.
U&)*("83
1. Carefully remove all tools, parts, etc.
from under the vehicle.
2. Position the Saddle under the lifting point.
Turn the Handle firmly clockwise and raise
load high enough to clear the jack stands,
then carefully remove jack stands.
3. Slowly turn the Handle counterclockwise
(never more than 1/2 full turn) to lower
the vehicle onto the ground.
4. Lower the Jack completely. Then, store in a
safe, dry location out of reach of children.
Page 7@&(%$*4.8"4,7%A'*#$"&8#B%/7*,#*%4,77%?CDDDCD==C<EFE1Item 56621
GH@6IJKL6MHI;KNOH;NI6NHNP6 G6IQL
O,"8$*8,84*%,89%G*(]"4"83
%L(&4*9'(*#%8&$%#/*4"2"4,77Y%*\/7,"8*9%"8%$."#%5,8',7%5'#$%
+*%/*(2&(5*9%&87Y%+Y%,%A',7"2"*9%$*4.8"4",81
IK%LM6!6NI%G6M;KQG%;NWQMJ%@MKO%IKKU%@H;UQM6-%
V&%8&$%'#*%9,5,3*9%*A'"/5*8$1%%;2%,+8&(5,7%8&"#*%&(%]"+(,$"&8%
&44'(#B%.,]*%$.*%/(&+7*5%4&((*4$*9%+*2&(*%2'($.*(%'#*1
P7*,8"83B%O,"8$*8,84*B%,89%U'+("4,$"&8
1. T6@KM6%6HP[%QG6B%inspect the general
condition of the Jack. Check for:
• loose or missing hardware
• misalignment or binding of moving parts
• cracked or broken parts
• any condition that may affect its safe operation.
If a problem occurs, have the problem corrected
before further use.
V&%8&$%'#*%9,5,3*9%*A'"/5*8$1
2. T6@KM6%6HP[%QG6B thoroughly test the Jack
for proper operation prior to its actual use.
If the Jack appears not to be working properly,
follow Bleeding instructions on page 5.
3. HI%U6HGI%KNP6%6!6MJ%I[M66 J6HMGB
change the hydraulic fluid:
a. With the Jack fully lowered, remove the
Fluid Fill Plug on the side of the Housing.
b. Tip the Jack to allow the old hydraulic fluid
to drain out of the Housing completely,
and dispose of the old hydraulic fluid in
accordance with local regulations.
c. With the Jack upright, completely fill the Housing
with a high quality hydraulic fluid (not included)
until the fluid is 1/4″ below the fill hole.
d. Open the valve by turning the Handle
counterclockwise and pump the Handle
to bleed air from the system.
e. Recheck fluid level and re-fill as needed.
f. Reinstall the Fluid Fill Plug.
4. H@I6M%6HP[%QG6B%wipe dry with a clean cloth.
Store the Jack in a safe, dry location out of reach
of children and other non-authorized people.
Page 8 @&(%$*4.8"4,7%A'*#$"&8#B%/7*,#*%4,77%?CDDDCD==C<EFE1 Item 56621
GH@6IJ KL6MHI;KN OH;NI6NHNP6G6IQL
I(&'+7*#.&&$"83
IK%LM6!6NI%G6M;KQG%;NWQMJ-%
Q#*%4,'$"&8%).*8%$(&'+7*#.&&$"83%,%5,72'84$"&8"83%d,4X1%%G$,Y%)*77%47*,(%&2%$.*%#'//&($*9%7&,91%
P&5/7*$*7Y%(*#&7]*%,77%/(&+7*5#%+*2&(*%'#*1%%;2%$.*%#&7'$"&8#%/(*#*8$*9%"8%$.*%I(&'+7*#.&&$"83%3'"9*%
9&%8&$%#&7]*%$.*%/(&+7*5B%.,]*%,%A',7"2"*9%$*4.8"4",8%"8#/*4$%,89%(*/,"(%$.*%d,4X%+*2&(*%'#*1
H2$*(%$.*%d,4X%"#%(*/,"(*9-%%I*#$%"$%4,(*2'77Y%)"$.&'$%,%7&,9%+Y%(,"#"83%,89%7&)*("83%"$%2'77YB%%
4.*4X"83%2&(%/(&/*(%&/*(,$"&8B%T6@KM6%M6IQMN;NS%I[6%WHPb%IK%KL6MHI;KN1
VK%NKI%QG6%H%VHOHS6V%KM%OHU@QNPI;KN;NS%WHPbZ
LKGG;TU6%GJOLIKOG
LMKTHTU6%GKUQI;KN
^O,X*%4*($,"8%$.,$%$.*%d,4X%"#%8&$%#'//&($"83%%
,%7&,9%)."7*%,$$*5/$"83%,%#&7'$"&81_
Jack will
not lift at
its weight
capacity
Saddle
lowers
under
load
Pump
stroke
feels
spongy
Saddle
will not
lift all
the way
Handle
moves up
when jack
is under
load
Fluid
leaking
from fill
plug
e e
Check that Release Valve is fully closed.
Bleed air from the system.
e e e
Valves may be blocked and may not close fully. To flush the valves:
1. Lower the Saddle and securely close the release valve.
2. Manually lift the Saddle several inches.
3. Open the release valve and force the Saddle down as quickly as possible.
e e e
Jack may be low on fluid. Check the fluid level and refill if needed.
Jack may require bleeding - see instructions on Bleeding on page 5.
e
Unit may have too much hydraulic fluid inside;
check fluid level and adjust if needed.
Page 9@&(%$*4.8"4,7%A'*#$"&8#B%/7*,#*%4,77%?CDDDCD==C<EFE1Item 56621
GH@6IJKL6MHI;KNOH;NI6NHNP6 G6IQL
LU6HG6%M6HV%I[6%@KUUKR;NS%PHM6@QUUJ
THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDED THE PARTS LIST AND ASSEMBLY DIAGRAM
IN THIS MANUAL AS A REFERENCE TOOL ONLY. NEITHER THE MANUFACTURER OR DISTRIBUTOR
MAKES ANY REPRESENTATION OR WARRANTY OF ANY KIND TO THE BUYER THAT HE OR SHE IS
QUALIFIED TO MAKE ANY REPAIRS TO THE PRODUCT, OR THAT HE OR SHE IS QUALIFIED TO REPLACE
ANY PARTS OF THE PRODUCT. IN FACT, THE MANUFACTURER AND/OR DISTRIBUTOR EXPRESSLY
STATES THAT ALL REPAIRS AND PARTS REPLACEMENTS SHOULD BE UNDERTAKEN BY CERTIFIED AND
LICENSED TECHNICIANS, AND NOT BY THE BUYER. THE BUYER ASSUMES ALL RISK AND LIABILITY
ARISING OUT OF HIS OR HER REPAIRS TO THE ORIGINAL PRODUCT OR REPLACEMENT PARTS
THERETO, OR ARISING OUT OF HIS OR HER INSTALLATION OF REPLACEMENT PARTS THERETO.
M*4&(9%L(&9'4$`#%G*(",7%N'5+*(%[*(*-%
N&$*- If product has no serial number, record month and year of purchase instead.
N&$*- Some parts are listed and shown for illustration purposes only,
and are not available individually as replacement parts.
Page 10 @&(%$*4.8"4,7%A'*#$"&8#B%/7*,#*%4,77%?CDDDCD==C<EFE1 Item 56621
GH@6IJ KL6MHI;KN OH;NI6NHNP6G6IQL
L,($ V*#4("/$"&8 f$Y
1 Saddle 1
2 Saddle Bolt 1
3 Lift Arm Assembly 1
4 Radius Link 2
5 Snap Ring 2
6 Washer 2
7 Cotter Pin 1
8 Spring 2
9 Front Wheel 2
11 Washer 2
12 Snap Ring 2
14 Lock Washer 4
16 Radius Link Stud 2
17 Lock Washer 4
18 Nut 2
19 Frame Tie Rod 2
20 Screw 4
22 Handle Bolt 2
23 Lock Washer 2
24 Bolt 4
25 Lock Washer 4
26 Left Plate Assembly 1
27 Right Plate Assembly 1
28 Rear Caster Assembly 2
29 Bearing 2
30 Snap Ring 2
31 Nut 2
32 Cover Plate 1
33 Screw 4
34 Ram Plunger 1
35 Bushing Cover 1
36 Washer 1
37 Sealing Ring 1
38 Top Nut 1
39 O-Ring 1
40 Wedge Ring 2
41 Reservoir 1
42 Cylinder 1
43 Washer 1
44 O-Ring 1
45 Oil Seal 1
46 Base 1
47 Ball 5
48 Release Valve Assembly 1
49 O-Ring 1
50 Ball 2
51 Washer 1
52 Lock Washer 1
L,($ V*#4("/$"&8 f$Y
53 Hex Bolt 1
54 Screw 1
55 O-Ring 1
56 Screw Safety Valve 1
57 Spring 1
58 Valve 1
59 Ball 1
60 Bolt 1
61 Back-Up Washer 1
62 O-Ring 1
63 Spring 1
64 Pump Piston 1
65 O-Ring 2
66 Pump 1
67 Washer 1
68 Pump Core Spring 1
69 Spring Sleeve 1
70 Spring Stop Sheet 1
71 Snap Ring 1
72 Pump Piston 1
73 Washer 2
74 O-Ring 2
75 Pump 1
76 Washer 1
77 O-Ring 1
78 Washer 1
79 Pump Core Spring 1
80 Spring Sleeve 1
81 Spring Stop Sheet 1
82 Snap Ring 1
83 Filter 2
84 Washer 1
85 Handle Base 1
86 Pin 1
87 Roller 1
88 Snap Ring 1
89 Bolt 1
90 Lower Handle 1
92 Upper Handle 1
93 Foam 1
94 Rubber Block 1
95 Snap Ring 1
96 Lift Arm Shaft 1
97 Snap Ring 2
98 Grease Fitting 1
99 Core Tube Assembly 1
100 Snap Ring 2
101 Handle Lock Button 1
L,($#%U"#$%,89%H##*5+7Y%V",3(,5
L,($#%U"#$
Page 11@&(%$*4.8"4,7%A'*#$"&8#B%/7*,#*%4,77%?CDDDCD==C<EFE1Item 56621
GH@6IJKL6MHI;KNOH;NI6NHNP6 G6IQL
H##*5+7Y%V",3(,5
1
2
3
4
5
4
5
9
11
11
9
161
23
23
24
252
242
252
26
28
29
30
28
29
30
32
33
3333
34
35
36
37
38
39
40
40
41
42
43
44
45
46
47
47
474
47
48
49
50
50
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
78
79
80
81
82
83
84
8
85
86
87
88
89
90
101
92
93
94
12
12
17
18
17
18
17
17
19
20
202
6
6
31
31
73
74
6
76
77
51
52
53
97
98
97
99
100
7
8
100
96
14
14
22
22
95
27
>=<g?%H3&'(,%M&,9%%h%%P,7,+,#,#B%PH%F?ij>%%h%%?CDDDCD==C<EFE
U"5"$*9%Fj%V,Y%R,((,8$Y
Harbor Freight Tools Co. makes every effort to assure that its products meet high quality and durability standards,
and warrants to the original purchaser that this product is free from defects in materials and workmanship for the
period of 90 days from the date of purchase. This warranty does not apply to damage due directly or indirectly,
to misuse, abuse, negligence or accidents, repairs or alterations outside our facilities, criminal activity, improper
installation, normal wear and tear, or to lack of maintenance. We shall in no event be liable for death, injuries
to persons or property, or for incidental, contingent, special or consequential damages arising from the use of
our product. Some states do not allow the exclusion or limitation of incidental or consequential damages, so the
above limitation of exclusion may not apply to you. THIS WARRANTY IS EXPRESSLY IN LIEU OF ALL OTHER
WARRANTIES, EXPRESS OR IMPLIED, INCLUDING THE WARRANTIES OF MERCHANTABILITY AND FITNESS.
To take advantage of this warranty, the product or part must be returned to us with transportation charges
prepaid. Proof of purchase date and an explanation of the complaint must accompany the merchandise.
If our inspection verifies the defect, we will either repair or replace the product at our election or we may
elect to refund the purchase price if we cannot readily and quickly provide you with a replacement. We will
return repaired products at our expense, but if we determine there is no defect, or that the defect resulted
from causes not within the scope of our warranty, then you must bear the cost of returning the product.
This warranty gives you specific legal rights and you may also have other rights which vary from state to state.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12

Pittsburgh 56621 Owner's manual

Type
Owner's manual
This manual is also suitable for

Pittsburgh Item 56621 is a 3-ton (6,000 lb.) capacity floor jack that can lift vehicles up to 18-1/4" high. It features a sturdy steel frame, a hydraulic lifting mechanism, and a wide base for stability. The jack is ideal for use in garages, workshops, and other automotive environments.

Some of the key features of the Pittsburgh Item 56621 floor jack include:

  • 3-ton (6,000 lb.) capacity: The jack can safely lift vehicles weighing up to 6,000 pounds, making it suitable for most cars, trucks, and SUVs.
  • 18-1/4" maximum height: The jack can lift vehicles up to 18-1/4" high, providing ample clearance for most maintenance and repair tasks.

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI