1
Electric Lift Salamander
User’s Manual
2
Ⅰ、Application
1.Although all the products fresh and frozen bread and flour products, baking sun can have.
2. All fresh and frozen meat products, dried, roasted.
Ⅱ、 Product structure and Annex
1. Product Structure
2. Product accessories
Ⅲ、Technical Parameters
Name
Lift Salamander
Lift Salamander
Lift Salamander
Model
OT-450S
OT-600S
OT-800S
Voltage
220V
220V
220V
Power
2.8KW
4KW
5.6KW
Dimensions
450*520*500mm
600*520*500mm
800*520*500mm
Temperature range
50~250℃
50~250℃
50~250℃
Weight
18kg
49kg
63kg
Case Material
Stainless steel
Internal material
Stainless steel
Supporting foot
Rubber Feet
Ⅳ、Matters needing attention
1. Special Note
Warning
Not suitable for home use. This product is a commercial machine, need to operate by trained
chefs.
Use can not and can tilt. Can not be converted, demolished or converted products can cause
serious accidents. Completed, to close the electric valve.
Do not open the machine casing, the product contains high voltage circuitry, demolition of
housing electric shock accident may occur.
Do not clean the product directly on the sprinkler, the water conductivity, the product may
cause equipment damage due to leakage and dangerous.
Work area during and after the fire, due to direct contact with high-temperature relationship
will not hand box other parts of the high temperature will cause burns.
3
Attentions
Minefields near, as soon as possible disconnect electric valve. Electrical appliances to avoid
damage due to lightning generated.
Prohibit the use of hard, sharp Untitled damage control panel.
If the power cord is damaged, in order to avoid risk, to the Department by the manufacturer,
or the maintenance or similar full-time.
2. Turns off the light after use
When not using this product, related to the proportion of device transferred to the position counterclockwise off
switch, and then to unplug or turn off the power.
Ⅴ、Installation requirements
1.All the power supplies and circuit connection must be by qualified personnel according to safety standards of
electrical installation trends.
2. This product should be placed away from combustible material where.
3. In the installation of equipment before, please check the electrical specifications of the contents of the required links
are good links.
4. This product should be placed on a solid place.
5. Please install in the environmental temperature between 0 ℃ ~ 35 ℃, relative humidity below 85%.
6. The installation of equipment, check the accessories are complete.
7. The installation of equipment before, check whether the appearance of damage.
8. Please place the product in an easy to connect cables and easy to maintain place.
9. Suggest that the product must be placed in a solid table or device rack. (Please product installed in a well-ventilated,
fire-fighting equipment with good places.)
10 before using the appliance and remove the surface film.
11. On the power cord must be in accordance with electrical safety standards.
12. In view before connecting the voltage and frequency data are consistent with the requirements of product
parameters.
13. Please supply line between the product and installation of a bipolar switch and fuse. When the products work, the
voltage of the error can not exceed 10%.
14. With a proper screwdriver to fasten the cable securely and fixed, and the use of copper bridge screws firmly press
and hold the power cord.
Note: To connect the ground wire. Power plug, wiring boards should not loose good contact. If the
connection is improper connection may cause fever and burning off the power line, causing a fire.
4
Warning
Products marked other than prohibiting the use of the power supply
Prohibit the use of non-compliance of the air switch, leakage switch
Notes
Circuit installation and maintenance must be carried out by qualified professional engineers.
Ⅵ、Operating Procedure
Note: Use all the parameters before install so check again to ensure correct before use.
1.Through the power supply, power supply is available at this time to use this product.
2. The proportion of clockwise rotation device, (the greater the Governor rotation home, the higher the furnace
temperature accordingly.) To the required temperature, heat lights, said heating tube is working, the furnace temperature
begins to rise, when the temperature reaches the required temperature , the ratio will automatically cut off the heat pipe
power while the lamp is off, now that the furnace has reached the required temperature, so that may work. The system
is automatic constant temperature, when the furnace temperature decreases, it will automatically heat, so repeated cycle,
the oven temperature to ensure the temperature within the set temperature.
3. Such as the right dial to the A position, a continuous electric heating tube.
4. This device has a bearing material frame and a plate bearing materials, the two attachments, when used in adjustment
according to the size of the food bearing plate racks and material position, this would make the satisfaction of cooking
thick foods.
5. Warning: cooking, please bring gloves, non-touch casing, to prevent burns.
Ⅶ、Care and Maintenance
1. Safeguard the former should Unplug, disconnect the power supply when the furnace cooled to clean.
2. A regular basis (recommended once a week) on the furnace cleaning, the bearing material frame out from the bore,
on the water with cleaning solution cleaning, second bore dry cloth after application of dry, wet and dry fabrics were in
use clean water rinse is strictly prohibited.
3. Must regularly by experienced professional and technical personnel to test or examination. (Recommended once a
month)
4. User Notes:
1. Product is not a little cleaning.
2. To wait before cooling furnace cleaning, do not can be used with acidic cleaning agents to clean.
3. Products make use of qualified personnel.
4. The operator should carefully read the instruction manual to understand the performance of furnace, uses, methods of
operation, manual shall be kept for future reading.
5
5. The device can only serve as food, baking sun surface use, other uses are inappropriate, this equipment allows
between 50 ~ 250 ℃ operating temperature.
5. Daily attention to check the machine status before and after.
Before use: the machine is tilted?
Have damaged the control panel?
Power lines are not aging?
Use: Are there any odor, the smell, there is no vibration noise?
Warning
Regular routine inspections must be
Regular checks of products that can prevent serious accidents.
Sense circuit, machine failure, we must stop using.
Ⅷ、Troubleshooting Guides
Problem
Causes
Possible Remedies
1. Close the power switch,the
furnace no power
1. Fuses
2. The power cord loose
1. Replaced by a suitable fuse
2. Rugged power cord
The green light is not
extinguished, the heater
temperature rise beyond the
control
1. The proportion of
devices
1. Replacement ratio of device
. LED does not light,
temperature control normal
1. Light poor contact
2. Light burned out
1. Strong connection
2. Replacement indicator
/
