Gymtech 50510 Owner's manual

Brand: Gymtech

Model: 50510

Category: Fitness, gymnastics & weight training

Type: Owner's manual

Gymtech 50510 is a home gym equipment designed to provide a full-body workout. It features various adjustable components that allow users to customize their锻炼 routine based on their fitness level and goals. The device comes with a weight bench, barbell support, leg developer, seat, and backrest pad, all of which can be adjusted to different positions and angles. This versatility enables users to perform a wide range of exercises, including bench press, squats, leg extensions, bicep curls, and more. The Gymtech 50510 is a compact and sturdy piece of equipment, making it suitable for home use.

NOTE:

Please read all instructions

carefully before using this

product

Table of Contents

Safety Notice

Hardware Identifier

Assembly Instruction

Parts List

Warranty

Ordering Parts

Model

50510

Retain This

Manual for

Reference

12-27-2011

OWNER'S

MANUAL

Weight Bench

50510

Please contact HUNTER LEISURE AUSTRALIA Should any

questions arise at 1800-632-792

Spare Part Service: If you require Spare Part service, please do

not return the Weight Bench to the store. Contact Hunter Leisure

Australia on 1800-632-792.

TABLE OF CONTENTS

BEFORE YOU BEGIN...................................................................................…. 1

IMPORTANT SAFETY NOTICES..................................................................…. 2

HARDWARE IDENTIFIER.....…....................................................................…. 3

ASSEMBLY INSTRUCTIONS........................................................................…. 4

EXPLODED DIAGRAM………………………………………………………………. 9

PARTS LIST...............................................................................................……. 10

ORDERING PARTS.......................................................................................… 11

BEFORE YOU BEGIN

Thank you for selecting the 50510 Weight Bench with weight set by Gym

Tech. For your safety and benefit, read this manual carefully before using

the machine. As a manufacturer, we are committed to provide you

complete customer satisfaction. If you have any questions, or find there are

missing or damaged parts, we guarantee you complete satisfaction through

direct assistance from our factory. To avoid unnecessary delays, please call

our TOLL-FREE customer service number. Our Customer Service Agents

will provide immediate assistance to you.

IMPORTANT SAFETY NOTICE

PRECAUTIONS

Toll-Free Customer Service Number

1800 632 792

Mon. - Fri. 9 a.m. - 5 p.m. AEST

This exercise machine is built for optimum safety. However, certain precautions apply

whenever you operate a piece of exercise equipment. Be sure to read the entire manual

before you assemble or operate your machine. In particular, note the following safety

precautions:

1. Keep children and pets away from the machine at all times. DO NOT leave children

unattended in the same room with the machine.

2. Only one person at a time should use the machine.

3. If the user experiences dizziness, nausea, chest pain, or any other abnormal symptoms,

STOP the workout at once. CONSULT A PHYSICIAN IMMEDIATELY.

4. Position the machine on a clear, leveled surface. DO NOT use the machine near water

or outdoors.

5. Keep hands and feet away from all moving parts.

6. Always wear appropriate workout clothing when exercising. DO NOT wear robes or

other clothing that could become caught in the machine. Running or aerobic shoes are

also required when using the machine.

7. Use the machine only for its intended use as described in this manual. DO NOT use

attachments not recommended by the manufacturer.

8. Do not place any sharp object around the machine.

9. Disabled person should not use the machine without a qualified person or physician in

attendance.

10. Before using the machine to exercise, always do stretching exercises to properly warm

up.

11. Never operate the machine if the machine is not functioning properly.

12. A spotter is recommended during exercise.

CARE AND MAINTENANCE

1) Lubricate moving parts with WD-40 or light oil periodically.

2) Inspect and tighten all parts before using the machine.

3) The machine can be cleaned using a damp cloth and mild non-abrasive detergent. DO NOT

use solvents.

4) Maximum weight capacity on the uprights: 100Kgs.

5) Maximum user’s weight: 120kgs.

6) Maximum weight capacity on the leg developer: 50kgs.

WARNING: BEFORE BEGINNING ANY EXERCISE PROGRAM, CONSULT YOUR

PHYSICIAN. THIS IS ESPECIALLY IMPORTANT FOR INDIVIDUALS OVER THE AGE OF

35 OR PERSONS WITH PRE-EXISTING HEALTH PROBLEMS. READ ALL

INSTRUCTIONS BEFORE USING ANY FITNESS EQUIPMENT. We ASSUME NO

RESPONSIBILITY FOR PERSONAL INJURY OR PROPERTY DAMAGE SUSTAINED BY

OR THROUGH THE USE OF THIS PRODUCT.

SAVE THESE INSTRUCTIONS.

HARDWARE IDENTIFIER

NOTE: The following parts are not drawn to scale. Please use your own ruler to measure the size.

ASSEMBLY INSTRUCTION

Tools Required Assembling the Machine: Two Adjustable Wrenches and Allen

Wrenches

NOTE: It is strongly recommended two or more people assembling this machine to

avoid possible injury.

STEP 1 (See Diagram 1)

A. Connect the Left & Right Barbell Support (#1& #2) by a Cross Brace (#3) in the Mid-span.

Secure them with two M10 x 70mm Carriage Bolts (#32), one Bracket (#13), two  10

Washers (#38), and two M10 Aircraft Nuts (#41) on each end of the Cross Brace.

B. Attach a Weight Plate Post (#9) to the Right Barbell Support (#2). Secure it with one M10

x 25 mm Allen Bolt (#34) and one ￠10mm Washer (#38).Slide a Rubber Bumper (#17)

onto the Weight Plate Post (#9). Attach a Spring Collar (#22) to the Post. Repeat the

same step to install the other side.

C. Place the Backrest Incline Support (#10) between the two Barbell Supports to obtain

desired incline.

DIAGRA1

STEP 2 (See Diagram 2)

A. Attach the Front Stabilizer (#5) to the Seat Support (#4). Secure it with three M8 x 15mm

Allen Bolts (#35) and Ø8mm Washers (#39). DO NOT tighten the Bolts yet.

B. Attach the Seat Support (#4) and the Cross Beam (#7) to the Cross Brace (#3). Align the

hole and secure with two M10 x 60mm Carriage Bolts (#31), two Ø10 Washers (#38), and

two M10 Aircraft Nuts (#41). DO NOT tighten the Bolts yet.

C. Attach the other end of Cross Beam (#7) to the Front Stabilizer (#5). Secure it with one

M8 x 15 mm Allen Bolt (#35) and Ø8mm Washer (#39).

Securely tighten all Nuts and Bolts previously installed.

DIAGRAM 2

STEP 3 (See Diagram 3)

A. Attach the Leg Developer (#8) to the Front Stabilizer (#5). Secure it with one M10x70mm

Allen Bolt (#33), two Ø10mm Washers (#38), and one M10 Aircraft Nut (#41).

B. Insert two Foam Tubes (#11) halfway through the holes on the Leg Developer. Push four

Foam Rolls (#21) onto the Tubes from both sides.

C. Place a Spring Color (#22) onto the weight post on the Leg Developer.

DIAGRAM 3

STEP 4 (See Diagram 4)

A. Attach Seat Pad(#15) onto the Seat Support(#4), Align the hole, secure with four

M6x35mm Hex Bolt(#36) and four ￠6mm Washer (#40).

B. Attach the front side holes of the two Backrest Support (#12) onto each side of the “pivot”

on the mid of the Seat Support (#4). Place another side of the two Backrest Support (#12)

onto the Backrest Incline Support (#10), place the Backrest Pad (#14) onto the two

Backrest Pad Support (#12), align the holes, secure with four M8x38mm Hex Bolt (#37)

and four ￠6mm Washer (#40).

DIAGRAM 4

STEP 5 (See Diagram 5)

A. Attach the Arm Curl Pad (#16) onto the Arm Curl Pad Support (#6), Align the holes secure with

two M8x15mm Allen Bolt (#35) and two ￠8mm Washer (#39).

B. Insert the Arm Curl Pad Support (#6) into the up opening of the Front Stabilizer (#5), select

desired height and secure with one M10 Lock Knob (#18).

DIAGRAM 5

Exploded Diagram

PARTS LIST

Key

No. Description QTY

Key

No. Description QTY

1 Left Barbell Support 1 22 Spring Collar 3

2 Right Barbell Support 1 23 ￠45×1.5mm End Cap 2

3 Cross Brace 1 24 ￠25×2.0mm End Cap 2

4 Seat Support 1 25 ￠25×1.5mm End Cap 2

5 Front Stabilizer 1 26 ￠25×1.2mm End Cap 4

6 Arm Curl Pad Support 1 27 ￠25×1.2mm Dome Head End Cap 1

7 Cross Beam 1 28 口 20×1.0mm End Cap 4

8 Leg Developer 1 29 口 25×1.0mm End Cap 4

9 Weight Plate Post 2 30 Plastic Grip 6

10 Backrest Incline Support 1 31 M10×60mm Carriage Bolt 2

11 Foam Roll Tube 2 32 M10×70mm Carriage Bolt 4

12 Backrest Support 2 33 M10×70mm Allen Bolt 1

13 Bracket 2 34 M10×25mm Allen Bolt 2

14 Backrest Pad 1 35 M8×15mm Allen Bolt 6

15 Seat Pad 1 36 M6×35mm Hex Bolt 4

16 Arm Curl Pad 1 37 M6×38mm Hex Bolt 4

17 Rubber Bumper 2 38 ￠10mm Washer 10

18 M10 Lock Knob 1 39 ￠8mm Washer 6

19 Bushing 2 40 ￠6mm Washer 8

20 45/38 Sleeve 1 41 M10 Aircraft Nut 7

21 Foam Roll 4

Gym Tech

Spare part ordering

Spare parts can be ordered by contacting Customer Services on 1800-632-792. Please make

sure you have the following information on hand when ordering spare parts.

 Operating Instructions

 Model Number (located on the cover sheet of these instructions)

 Description of attachments

 Attachment Number

 Proof of purchase with purchase date

Please don’t send the device to our firm without being requested to do so by our Service

team. The costs of unsolicited shipments will be borne by the sender.

Please don’t send the device to our firm without being requested to do so by our Service team.

The costs of unsolicited shipments will be borne by the sender.

Gymtech 50510 Owner's manual

Brand: Gymtech

Model: 50510

Category: Fitness, gymnastics & weight training

Type: Owner's manual

Download PDF

report

Gymtech 50510 Owner's manual

Gymtech 50510 Owner's manual

Other documents