Hytronik HE8050-A Dimmable LED Driver User manual

Hytronik
Brand
Hytronik
Model
HE8050-A Dimmable LED Driver
Type
User manual
INSTRUCTION MANUAL FOR 50W DIMMABLE LED DRIVER
MODEL NO.: HE8050-A
The current can be easily configured by choosing the correct combination of
the DIP switches (see table below).
LED CURRENT SELECTIONWIRING DIAGRAM
Switch-DIM wiring diagram
Note: 1. Default setting is “1-10V” dimming.
2. This “1-10V” output is isolated, SELV output.
3. To shift dimming from “Switch-Dim” to “1-10V”, the 1-10V leads
should be short-circuit for at least 3s.
Up to 50 drivers can be connected to the same switch, thanks to the programme. This means there is no need for any additional synchrony wire in large installation,
where many drivers should be controlled by one switch.
Please follow the steps below to achieve synchronization function if more than one driver is connected to the same push button:
Press the push button for more than 1s (long push), then a short push (<1s). Now the devices are switched off.
Long push the button, the system is now synchronized.
SPECIFICATION
SWITCH-DIM
push and hold to dim On/off control: short push (<1s) on the switch.
Note: Short push should be at least 0.12s, and the time interval between two pushes should be longer than 0.12s also.
Stepless dimming: long push (>1s) on the switch.
For fine tuning of light level: with every alternate long push, the light level goes to the opposite direction.
Built-in permanent memory: light returns to the previous dimming level when switched off and on again,
even after power failure.
SYNCHRONIZATION
In the case of overload, overheat, or poor electrical contact, drivers can get overheated. Instead of shutting down, this smart driver automatically reduces power
output by 20% to reduce the thermal load, and further 20% more... until the thermal condition is at a safe level for the driver to work in a stable condition.
As the driver cools, the light output goes back to 100%.
INTELLIGENT THERMAL MANAGEMENT
Mains voltage 220-240VAC 50/60Hz
Mains current 290 ~ 270mA
Mains power 58W (Maximum)
Power consumption ≤0.5W
Output voltage (U-out) 100V(Maximum)
Power factor ≥0.9
Operation temperature Ta: -20~+45 Tc:80(Maximum)
Efficiency 87%(Maximum)
Dimming interface Push, 1-10V
Dimming range 1-100%, flicker-free
Abnormal protection Output short-circuit protection
Over-heat protection, Permanent memory
EMC standard EN55015; EN61547; EN61000-3-2/3-3
Safety standard EN61347-1, EN61347-2-13
Dielectric strength Input→output : 3750VAC/5mA/1min
1-10V dimming wiring diagram
Switch-Dim
N L
67
79.2
30
4.5
111
123.2
Switch Dim
L N L N
L
N
Switch-Dim
L
N
1-10V
1-10V
+
-
+
-
+
-
LED
L
N
1-10V +
-
LED+
-
1Current 2 3
350mA
500mA
550mA
600mA
650mA
700mA
800mA
900mA
4 5
1050mA
5~25W/350mA/15~72V; 7~36W/500mA/15~72V
8~40W/550mA/15~72V; 9~43W/600mA/15~72V
10~47W/650mA/15~72V; 10~50W/700mA/15~72V
12~50W/800mA/15~63V; 13~50W/900mA/15~56V
15~50W/1050mA/15~48V
Max. output
power/current/voltage
LED+
-
HE8050-A
HE8050-A
HE8050-A
L
N
Switch-Dim
LED+
-
HE8050-A
HE8050-A-20170608-A1
3rd Floor, block C, complex building, 155#, Bai'gang road south,
Bai'gang village, Xiao Jin Kou town, Huicheng district, Huizhou 516023
Tel:86-752-2772020 F:86-752-2777877
E: [email protected] W:www.hytronik.com
CHINA FACTORY
Room D, 10/f, Tower A, Billion Center, 1 wang Kwong Road,
Kowloon Bay, Kowloon, Hongkong
T: 00852-35197525 F: 00852-30116936
E: [email protected]
HYTRONIK INDUSTRIAL LIMITED
  • Page 1 1

Hytronik HE8050-A Dimmable LED Driver User manual

Hytronik
Brand
Hytronik
Model
HE8050-A Dimmable LED Driver
Type
User manual
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents