FMS MG41 User manual

Brand: FMS

Model: MG41

Type: User manual

FMS MG41: This high-performance 1/24 scale RC truck boasts a tough chassis, independent suspension, and powerful motor for conquering various terrains. With its compact size and agility, it's perfect for indoor and outdoor adventures. Explore its durability and precision control as you race through obstacles and challenges.

Length: 210mm

Width: 124mm Height:132mm

Wheel base: 138mm Ground clearance: 26mm

Approach angle: 68° Departure angle:> 90 °

SPECIFICATION

Instruction Manual

操作手册

1:24 FCX24

POWER WAGON

Introduction

Safety, precautions and warnings

SAFETY PRECAUTIONS

CE compliance information for the european union

UK DE DK BG SE GZ ES NL SK HU RO FR PT BE

FI EE LV LT PL AT CY SI GR MT IT IE LU

• Replace damaged components with original factory-parts. Pay special attention to the polarity of all

vehicle wiring.

• Use common sense when selecting the environment to operate your vehicle. Do not operate near

power cables, cellular/radio towers, deep water or unstable terrain. The operator is solely responsible

for their actions.

• The product is composed of precision electrical components. It is critical to keep the product away

from moisture and other contaminants.

• Always check the radio range of the vehicle prior to operation in order to prevent radio loss or

interference.

• Operate this product within your ability. If the vehicle is dangerous to retrieve, it never worth the risk.

• Always turn on the transmitter before connecting the battery on the model. When turning off the

model, always disconnect the battery first, and then turn off the model, always disconnect the battery

first, and then turn off the transmitter. If this order is reversed, the model may become uncontrollable

and cause serious damage.

• Never allow transmitter batteries to run low as it may cause loss of vehicle control.

• Plastics on the vehicle are susceptible to damage or deformation due to extreme heat and cold

climate. Do not store the model near any source of heat such as oven or heater. Store the model

indoors, in a climate-controlled, room temperature environment.

The associated regulatory agencies of the following countries recognize the noted certifications for

this product as authorized for sale and use.

This manual is written to assist you in properly operating, maintaining and repairing the vehicle.

As many of the components used are unique to this truck, please retain this manual as a future

reference.

Composed of precision-made components, this product not a toy, thus it is not suited for children

under 14 years of age. Minors should be accompanied by an adult when operating. Failure to operate

or maintain this vehicle in a safe manner can result in bodily harm.It is the owner responsibility to

operate this product in a safe manner. and its distributors are not responsible in any way for any and

all bodily harm and/ or property damage that may result from the use of this product. Replace

damaged components with original factory-parts.

Pay special attention to the polarity of all vehicle wiring.

Declaration of Conformity

Products: 2.4GHz Controller

Equipment Class: 2

The objects of declaration described above are in

conformity with the requirements of the specifications

listed below.

Item Name : 2.4GHz Controller

The RED Directive 2014/53/EU

EN 60950-1:2006 + A11:2009 + A1:2010

+ A12:2011 + A2:2013

EN 300 328 V2.2.2 (2019-07)

EN 301 489-1 V2.1.1:2017

EN 301 489-17 V3.1.1:2017

MADE IN CHINA

FCC ID: N4ZR4A10

Certification

FCC Compliance Statement

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two

conditions: (1) this device may not cause harmful interference, and (2) this device must accept any

interference received, including interference that may cause undesired operation.

Warning: changes or modifications not expressly approved by the party responsible for compliance

could void the user's authority to operate the equipment.

This equipment has been tested and found to comply with the limits for a Class B digital device,

pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection

against harmful interference in a residential installation. This equipment generates, uses and can

radiate radio frequency energy and, if not installed and used in accordance with the instructions, may

cause harmful interference to radio communications. However, there is no guarantee that

interference will not occur in a particular installation.

If this equipment does cause harmful interference to radio or television reception, which can be

determined by turning the equipment off and on, the user is encouraged to try to correct the

interference by one or more of the following measures:

1.Reorient or relocate the receiving antenna.

2.Increase the separation between the equipment and receiver.

3.Connect the equipment into an outlet on a circuit different from that to which the receiver is

connected.

4.Consult the dealer or an experienced radio/TV technician for help.

RF Exposure Compliance

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled

environment. This equipment should be installed and operated with minimum distance 20cm

between the radiator and your body. This transmitter must not be co-located or operating in

conjunction with any other antenna or transmitter.

Environmentally friendly disposal

Old electrical appliances must not be disposed of together with the residual waste, but have to be

disposed of separately. The disposal at the communal collecting point via private persons is for free.

The owner of old appliances is responsible to bring the appliances to these collecting points or to

similar collection points. With this little personal effort, you contribute to recycle valuable raw

materials and the treatment of toxic substances.

This product is not a toy! (14+) Recommended for ages 14 and up. Adult

supervision required for ages under 14 years old. Contains small parts, keep

out of reach of children 3 years of age and younger.

Safety symbols

Safety guide

RADIO SYSTEM

Danger Not following these instructions may lead to serious injuries or death.

Warning Not following these instructions may lead to major injuries.

Attention Not following these instructions may lead to minor injuries.

Prohibited Mandatory

Pay close attention to the following symbols and their meanings. Failure to follow these warnings

could cause damage, injury or death.

• Do not use the product at night or in bad weather like rain or thunderstorm. It can cause

erratic operation or loss of control.

• Do not use the product when visibility is limited.

• Do not use the product on rain or snow days. Any exposure to moisture (water or snow)may

cause erratic operation or loss of control.

• Interference may cause loss of control. To ensure the safety of you and others, do not

operate in the following places:

1Near any site where other radio control activity may occur

2Near power lines or communication broadcasting antennas

3Near people or roads

4On any body of water when passenger boats are present

• Do not use this product when you are tired, uncomfortable, or under the influence of alcohol

or drugs. Doing so may cause serious injury to yourself or others.

• The 2.4GHz radio band is limited to line of sight. Always keep your model in sight as a large

object can block the RF signal and lead to loss of control.

• Do not touch any part of the model that may generate heat during operation, or immediately

after use. The engine, motor or speed control, may be very hot and can ause serious burns.

• Misuse of this product may lead to serious injury or death. To ensure the safety of you and

your equipment, read this manual and follow the instructions.

• Make sure the product is properly installed in your model. Failure to do so may result in

serious injury.

• Make sure to disconnect the receiver battery before turning off the transmitter. Failure to do

so may lead to unintended operation and cause an accident.

• Ensure that all motors operate in the correct direction. If not, adjust the direction first.

• Make sure the model stays within the systems maximum range to prevent loss of control.

PRODUCT INTRODUCTION

Background

The MUD MASTER is held every June in Manchac, near New Orleans, Louisiana, where there are

dense swamps, rugged rocks, and dead woods, making it difficult for off-road vehicles to move.

Legend has it that this area was cursed by the Queen of Voodoo Mary Poppin, and there is a

mysterious singing that attracts people to get lost in the jungle, and there is no return. The swamp

is also home to giant alligators that can devour adults..The stories were chilling, but they drew

waves of young people who ventured into this no-man’s land, deep into the swampy hinterland,

and garnered attention by sharing their location on Twitter. There are many people going in, and

there are occasional unfortunate disappearances. But instead of deterring people from entering, it

acts like a magnet to attract more visitors.

In fact, this is a very beautiful ancient forest. The founder of the race, Chandler Bing, was born and

raised on a nearby farm. He believes that no matter how powerful the vehicle is, it is difficult to

pass here, and no matter how deep the rut is, it is difficult to maintain a week. Human beings are

insignificant in front of nature and should live full of humility and awe under the protection of

nature. Therefore, in 2007.01.01, the MUD MASTER cross-country race was established to test

the limits of people and machines, and at the same time, let the audience feel the pure power of

nature. Mary Poppin is his college teacher and his second wife, alligators are a traditional local

delicacy, and Gator Tail Bites is the most popular dish among racers.

The race is open to anyone with a minimum FIA C1 licence. However, it does not accept

registrations or sponsorships from car manufacturers' teams, and does not allow the

manufacturer's logo to be exposed. The purpose is to limit the entry of large capital and high

technology, and to make the competition pure and simple. A significant portion of the competition's

operating income is donated to local active environmental organizations for conservation and

earth science education.

After 12 years of development, the scale and influence of the event has expanded year by year. In

2019, it was absorbed by the Amazon Rainforest Challenge and became the largest off-road

racing carnival in the world. In recent years, with the advancement of electric vehicle technology,

the proportion of hybrid racing cars is getting higher and higher, and pure electric vehicles have

begun to join in 2021. Due to the extremely complex environment, most racing cars choose to

install tractor tires. The huge herringbone pattern has a good mud removal effect. The customized

short wheelbase chassis ensures the longitudinal passability of the racing car, and the portal axle

is just starting line.

The initial participants were mostly local farmers, ranchers and crocodile breeders who had years

of experience scrambling around in the mud, which is why their cars looked so much like tractors.

William Butch is a newcomer to the event in 2020. His father is a large local cattle farmer, and he

himself is responsible for the slaughter and beef sales. People nicknamed him Butcher. His car

uses a lot of parts from agricultural vehicles, and the casing comes from the legacy of his uncle

Douglas Butch, a 1949 POWER WAGON.

PRODUCT INTRODUCTION

Features

Because of the sturdy driving style, not playing cards according to common sense, and being

familiar with the local climate and terrain, he has repeatedly won by surprise. Soon, the name of

“Butcher Butch”spread.

To be continued...

FCX24 is positioned as a high-performance crawler chassis. The carframe is made of

high-strength nylon. Compared with the trapezoidal beam spliced by metal side beams and plastic

trusses, the overall weight is lighter and the strength is higher. The mid-mounted power assembly

has a low center of gravity and integrates the 2-speed transmission, transfer case and 130 motor.

The power is transmitted to the front and rear axles through the universal joint drive shaft. The

axles are equipped with wheel side reducers, commonly known as "portal axle", which can

increase the ground clearance of the differential tooth pack and improve the passability.

The crawlersare generally equipped with front and rear straight axles to simulate the locked state

of the real car differential to improve off-road passing ability. The FCX24 is equipped with a

straight axle by default, but the planetary gear differential can also be replaced with high-viscosity

silicone oil to simulate the driving effect of an LSD limited-slip differential. After installing the

differential, the ultimate climbing ability will be reduced, but a smaller turning radius and a more

stable high-speed driving quality can be obtained. Simply put, the straight axle is suitable for

extreme climbing, and the limited-slip differential is suitable for high-speed off-road. The choice is

yours.

The two-speed gearbox uses the CH3 of the remote control and is operated by a 9G steering gear.

The low gear reduction ratio is 99, which is larger than that of similar products currently on the

market. The torque output is strong, and easy for extreme climbing. The high gear reduction ratio

is 24.75, and the speed is higher than that of all similar products currently on the market. You can

experience the fun of high-speed breakthrough, small jump, and even heading up.

Stainless steel ball bearings are always the favorite of players, but in order to reduce the street

price, most brands will choose bushings as a replacement for all or part of the bearings. However,

considering that players need to completely disassemble the whole car to upgrade the bearings in

future, which is slow and laborious, FCX24 chooses to pre-install the whole car with a total of 24

bearings, which does not need to be disassembled and re-upgraded, saving time and effort, and

addresses the concern once for all.

● Ready to run model

● Two speed transmission

● Portal axle

● 24 ball bearings full set

● Metal gears steering servo

● Four link suspension

● High strength integrated nylon frame

● Power wagon polystyrene body

● Rapid separation car body

● Nylon roll cage

● Painted body

● Remote control lighting system

● Original personalized stickers

About Model

PRODUCT INTRODUCTION

Specification

As the first product of the FCX24 series, the car body is the POWER WAGON in 1949, which

appeared in the form of a mud off-road truck. We put the reason and future development in this

story to share with you.

2.4G 4-channel digital proportional remote control system, in addition to normal driving and

steering control, the CH3 is used to control shifting, and the CH4 is reserved for players’

imagination expansion. It is also equipped with a lighting control module, and the headlights can

be switched between high and low beams. In addition, interfaces for taillights and turn lights are

reserved for players to modify.

Unlike previous FMS products, FCX24 focuses more on sports performance. A large number of

upgraded and modified parts such as metal gears, shock absorbers, high-performance motors,

radiators, and wheel hub counterweights will be launched simultaneously. Players from all over

the world, look forward to you creating your own unique FCX24.

● Length : 210mm

● Width : 125.7mm

● Height : 131mm

● Wheelbase : 138.8mm

● Tire F/R Φ 60 × 20mm

● Minimum Ground Clearance 38.8mm

● Approach Angle 67.7°

● Departure Angle > 90 °

● Reduction ratio (High Gears ) 24.75 (Low Gears ) 99

Transmitter intruction

Intruction

FS-R4A1 based on ANT protocol is a three-in-one receiver with ESC and LED light group control

board. It has an external single antenna, can output PWM signal and light control signal, can

implement two-way transmission, adopts automatic binding, and has a compact design, which can be

adapted to various model cars.

TransmitterOverview

Traversing handwheel, 35 degrees on

each side (CH1)

Throttle button, 25 degrees in front and

12.5 degrees at rear (CH2)

Push button switch (CH4) [Push button

function is flip type]

Three-position toggle switch (CH3)

Lanyard hole

Handle, 4*AAA battery compartment

ST.REV

R.LED

RX.BATT

ST.D/R

TH.D/R

Switch to the electric adjustment mode

TH.REV

G.LED

BIND

ST.TRIM

TH.TRIM

Power Switch

[1]

[2]

[3]

[4]

[5]

[6]

[7]

[8]

[9]

[10]

[11]

[12]

[13]

[14]

[15]

[16]

[17]

[18]

[1]

[2]

[3]

[4]

[5]

[6]

[7] [13]

[12]

[14]

[16]

[15]

[17]

[18]

[8]

[9]

[11]

[10]

• Product Name: FS-R4A1

• Adaptive transmitter: FS-MG41

• Model Type: Car

• Channels: 4

• Numbers of Light Interfaces: 7

• RF: 2.4GHz ISM

• 2.4G Protocol: ANT

• Antenna: Single antenna

• Input Power: Lipo (2S)/NiMH (5~7Cell)

• BEC Output: 6V/1A

• Continuous/Peak Current: 10A/50A

• Data Output: PWM

• Temperature Range: -10 —+60

• Humidity Limit: 20%~95%

• WaterProof: PPX4

• Online Update: No

• Dimensions: 33mm*30mm*12mm

• Weight: About 11g

• Certification: CE, FCC ID: N4ZR4A10

Overview

[1] CH1

[2] CH3

[3] CH4

[4] Left-turn light port

[5] Head light port

[6] Right-turn light port

[7] Head light port

[8] Fog light port

[9] Fog light port

[10] Antenna

[11] Power switch

[12] Battery line "+"

[13] Battery line "-"

[14] Motor port "+"

[15] Motor port "-"

[16] Stickers

[17] LED

[18] Left-turn light port

[19] Right-turn light port

[20] Reversing light port

[21] Brake light port

[22] Taillight port

[23] Signal pin

[24] Power "+"

[25] Power "-"

Specifications

ESC protection

This receiver has multiple prompt functions such as power-on self-check display, overheating alarm

prompt,and low/high voltage alarm prompt.

• Self-check display: all car lights will be on for 1S when the receiver is powered on;

• Overheating alarm: When the internal temperature of the ESC is detected to exceed 110 °C,motor

has no output, all car lights flash promptly, and the normal output will be restored when the

temperature is lower than 70°C;

• Low/high voltage alarm: When the receiver enters the low voltage protection, motor has no output,

and all the lights flash slowly; when the receiver enters the high voltage protection, all channels have

no output. All car lights flash promptly.

ESC function instructions

1.Connect related equipment:

Make sure the ESC is off before connection.Connect the motor with M+ and M- of ESC. Connect the

steering servo to the 3Pin interface marked with "ST" of ESC (- + S connected

correspondingly).Connect the battery with the positive and negative poles of ESC correspondingly.

2. Normal boot, identification throttle midpoint:

After connecting related equipment as step 1, turn on the radio first, move the throttle trigger to the

neutral position. Turn on the switch of ESC at last. The receiver will automatically recognize the

battery type when it is powered on again. Then it can run it.

Notes:

a. The ESC can be run after completing self-inspection (about 3 seconds) if power on, otherwise it

cannot be operated normally.

b. If there is no power output and the red light of ESC flashes quickly after power on, please check

whether the throttle trim of the transmitter is set to the "0" position, the receiver will automatically

recognize the midpoint of the trim throttle after restarting;

c. If the rotation direction is not correct during running, exchange the two wires connecting motor and

ESC.

d. To make sure everything is ok, please turn on the transmitter first and finally turn on the ESC, turn

off the ESC first and finally turn off the transmitter.

Notes: Please refer to the relevant sections for details about the battery type, drag brake force and

running mode of the ESC.

Binding

The receiver automatically enters the binding state once it is powered on.

Press the BIND Key to turn on the transmitter and allow it to enter its binding state. Here, G.LED

flashes quickly, and operator releases the BIND Key.

1. When the receiver is powered on and waits for 1 second, it will automatically enter the binding state

if it is not connected;

2. After the binding is successful, the LED indicator of the receiver is always on.

Notes: (1) Set the transmitter to its binding state first, and then set the receiver to its binding state. If

the binding is not completed within 10s, the indicator light of the receiver will enter its slow flashing

state. (2) If re-binding is successful, all the settings of the car lights will be restored to their default

values.

This function is used to protect the safety of the model and the operator when the receiver cannot

normally receive the signal from the transmitter and is out of control. The receiver defaults that the

throttle channel is fixed to be out of control and enters the brake state. After other channels are out

of control, the receiver has no signal output. If you set it on the transmitter, it will output according to

the set value.

Attention:

• Make sure the product is installed and calibrated correctly, failure to do so may result in serious

injury.

• Please carefully check each power device and car frame instructions to ensure the power matching

is reasonable before use. Avoid damaging power system due to incorrect matching.

• Do not let the external temperature of the system exceed 90°C /194°F , because high temperature

will damage the power system.

• Make sure the receiver's battery is disconnected before turning off the transmitter, failure to do so

may lead to unintended operation or loss of control.

• After use, remember to disconnect the battery and the ESC. If the battery isn't disconnected, the

ESC will consume electric energy all the time even if it is off. It will discharge completely if connect

the battery for a long time, thus resulting in the failure of the battery or the ESC. We are not

responsible for any damage caused by this!

• Make sure the receiver is mounted away from motors or any device that emits excessive electrical

noise.

• Keep the antenna of the receiver at least 1cm away from conductive materials such as carbon or

metal.

• Do not power on the receiver during the setup process to prevent loss of control.

Failsafe

ESC Parameter Setting

Dial Switch sign

Running Mode

FWD/REV/BRK

FWD/REV

Lipo

NiMH

50%

75%

100%

Battery Type Drag Brake

Setting Method:

There are three parameters can be set for the ESC, which are "Running mode", "Battery type", "Drag

brake", There are slide switches numbered 1 2 3 4 on the radio panel . The above parameters can be

set by dialing down and up.

The specific operation is as follows:

The Dial Switch on the transmitter is used to set ESC parameters, that is, the Dial Switch is located

at different positions and the corresponding parameter values are different.

When No. 1 slide switch is on the down, it indicates that the operation mode is set to

FWD / REV / BRK.

When No. 1 slide switch is on the up, it indicates that the operation mode is set to FWD/REV.

When No. 2 slide switch is on the down, it indicates that the battery type is set to Lipo.

When No. 2 slide switch is on the up, it indicates that the battery type is set to NiMH.

When No. 3 and No.4 slide switch are on the down, it indicates that the drag brake force is set to 0%.

When No. 3 slide switch is on the down and No.4 slide switch is on the up, it indicates that the drag

brake force is set to 50%.

When No. 3 slide switch is on the up and No.4 slide switch is on the down, it indicates that the drag

brake force is set to 75%.

When No. 3 and No.4 slide switch are on the up, it indicates that the drag brake force is set to 100%.

Parameter Explanation:

1. Running Mode

FWD/REV/BRK: This mode adopts "double click” reverse mode, that is, when the throttle trigger is

pushed from netural range to the reverse area for the first time, the motor is only braking and will not

reverse; when the throttle trigger is moved back to the netural range and pushed to the reverse area

for the second time, it will reverse. This mode is applicable to general models.

FWD/REV: This mode adopts "one click" reverse mode, that is, when the throttle trigger is pushed

from netural range to the reverse area, the motor immediately generates reverse action, which is

generally applied to rock crawler.

Parameter setting method:

When No. 1 slide switch is on the down, it indicates that the operation mode is set to FWD / REV /

BRK.

When No. 1 slide switch is on the up, it indicates that the operation mode is set to FWD/REV.

2. Battery Type

There are LiPo and NiMH cells. The low-pressure protection value is different under different types.

It can be set according to the actual use.

Parameter setting method:

When No. 2 slide switch is on the down, it indicates that the battery type is set to Lipo.

When No. 2 slide switch is on the up, it indicates that the battery type is set to NiMH.

3. Drag Brake Force

The drag brake means that when the throttle trigger moves from the forward or reverse area to netural

range, it will produce certain braking force to the motor, the larger the value is, the greater the drag

brake force is. Select proper braking force according to the actual situation.

Parameter setting method:

When No. 3 and No.4 slide switch are on the down, it indicates that the drag brake force is set to 0%.

When No. 3 slide switch is on the down and No.4 slide switch is on the up, it indicates that the drag

brake force is set to 50%.

When No. 3 slide switch is on the up and No.4 slide switch is on the down, it indicates that the drag

brake force is set to 75%.

When No. 3 and No.4 slide switch are on the up, it indicates that the drag brake force is set to 100%.

Lighting function

Times for Pressing

Button Light

Position

HeadlightCH4

White

headlights

keep on

White

headlights

keep on with

high

brightness

I II III IV V

OFF

OFF OFF

OFF OFF OFF

OFF

•

••

Control

Mod Remarks

Function

Power on

is off by

default

Throttle stick position

THROTTLE STICK POSITION

Neutral point Top point of forward direction Top point of backward direction

Getting started

Instructions

Transmitter Battery Installation

Before operation, install the battery and connect the system as instructed below.

Danger

Only use specified battery (X4 AA batteries).

Do not open, disassemble, or attempt to repair the battery.

Do not crush/puncture the battery, or short the external contacts.

Do not expose to excessive heat or liquids.

Do not drop the battery or expose to strong shocks or vibrations.

Always store the battery in a cool, dry place.

Do not use the battery if damaged.

Battery Type: AAA

Battery Installation:

1.Open the battery compartment cover.

2.Insert 4 fully-charged AAA batteries into the compartment. Make sure that the battery makes good

contact with the battery compartment's contacts.

3. Replace battery compartment cover.

Low battery alarm: When the battery is lower than 4.2V, the LED on the panel will flash slowly.

After setting up, follow the instructions below to operate the system.

1. Automatic code matching (the transmitter and receiver have been successfully coded before

leaving thefactory.)

If you need to replace another transmitter or receiver, please follow the following steps to code:

1. When the transmitter power is on and the code matching mode is on, the light keeps flashing;

2. The power supply of the receiving board is turned on, and the front lights keep flashing to enter the

code matching mode;

3. When the code matching is successful, all the transmitter lights are on and all the lights on the car

are off;

Note: when code matching, please operate the transmitter to enter the code matching state first, and

then operate the receiver to enter the code matching state.

Connecting the battery

VEHICLE SETUP

Step 1: Separate the car shell, the two buckles in the front of the car shell are opened outward, and

the two buckles at the rear of the car shell are opened inward.

Step 2: Place the battery in the battery compartment on the frame and fix it with the attached rubber

band.

Step 3: Connect the battery plug.

NOTE

1.If it is not in use for a long time, unplug

and take off the battery to prevent battery

leakage.

2.Do not open, disassemble, or attempt to

repair the battery.

3. The battery needs to be disconnected

from vehicle before it can be charged

4. Do not charge battery in vehicle.

1 2

OPERATING THE VEHICLE

Step 1: turn on the transmitter, the headlamp of the transmitter will flash and enter the frequency

matching mode.

Step 2: turn on the receiver switch, the headlight will flash and enter the frequency matching mode.

Step 3: when the transmitter and receiver are successful in frequency up, the front lights of the

transmitter will be on for a long time, and the front lights of the vehicle will be off.

Spare parts list

C3040

C3000

C3001

C3002

C3003

C3004

C3005

C3006

C3007

C3008

C3009

C3010

C3011

C3012

C3013

C3014

C3015

C3016

C3017

C3018

C3019

C3020

C3021

C3022

Mud tire

Front bumper

Girder

Oil shock absorbers assembly

Wiper

Car boby

Windows

Lens set

Wheel

Snokle

Side panel

Exhaustion plate

Window frame

Transmission gear box assembly

Transmission shaft

Transmission gear box plastic

Gear set

Steering link set

Front axle assembly

Axle plastic parts

Portal axle cover

C hub set

Portal axle set

Rear wheel shaft set

Front dog bone set

Differential set

Cvd axle set

Rear axle assembly

Servo mount

Rod set

Servo horn set

Pinion gear

Bush

130 motor

Screw

Screw nut

MG41 + R4A1 transmitter receiver set

MG41 transmitter

R4A1 esc/rx combo

Steering servo

Variable speed servo

FMS lipo battery 2s 380mah

Led light set

Car decal sheet

Bearing set

Fuel tank

Anti roll bar

Spare tire bracket

C3023

C3024

C3025

C3026

C3027

C3028

C3029

C3030

C3031

C3032

C3033

C3034

C2131

C2122

C2130

C3035

C3036

C1389

C3037

C3038

C3039

C3041

C3042

C3043

1 2

Roll Cage installation

1: Use the included 2 PB1.2x3 Phillips head screws to install the left and right brackets on the

middle bracket;

2: Use the included PWB2.3x12M5.5 meson head screws to install the tire set to the spare tire

frame;

3: Install the assembled spare tire frame on the left and right brackets;

4: Install the assembled roll cage on the frame;

5: Use the included double-sided tape to stick the fuel tank to the corresponding position of the

frame.

PB1.2x3 Phillips head screws

middle bracket

left and right brackets

tire set

spare tire frame

double-sided tape

PWB2.3x12M5.5 meson head screws

EN:Finished Frame Sets CN:车架成品组

C3040

C3016 C3028

C3028

C3029

C3017

C3002

C3016

C3034

C3040

C3026 C3002

C3001

EN:Wheels CN:车轮

C3040

C3007

EN:Frame Sets CN:车架组

C3012

C3027

C3028

C3012

C3001

C3017 C3028 C3028

C3026

C3017

C3028

C2131

C1389

Page is loading ...

FMS MG41 User manual

FMS MG41 User manual

Related papers

Other documents