Ranger design C30-DL Installation guide

Category
Wall & ceiling mounts accessories
Type
Installation guide

Ranger design C30-DL is a straight partition specifically designed for Sprinter Vans that features a swing door made of steel. The C30-DL is easy to install and provides a secure and durable barrier within the vehicle. This partition is ideal for creating separate compartments within the van, enhancing privacy, security, and organization. Whether you need to divide the passenger and cargo areas, create a dedicated workspace, or isolate sensitive equipment, the Ranger design C30-DL offers a practical solution.

Ranger design C30-DL is a straight partition specifically designed for Sprinter Vans that features a swing door made of steel. The C30-DL is easy to install and provides a secure and durable barrier within the vehicle. This partition is ideal for creating separate compartments within the van, enhancing privacy, security, and organization. Whether you need to divide the passenger and cargo areas, create a dedicated workspace, or isolate sensitive equipment, the Ranger design C30-DL offers a practical solution.

INSTALLATION GUIDE
C30-DL STRAIGHT PARTITION
Sprinter Partition ( Swing Door, Steel )
Scan the QR code for
the digital Install Guide.
For technical support, contact us at 1-800-565-5321 C30-DL Installation Guide | REV. G2 | Page 2
REQUIRED ITEMS
2
PERSONS
q Cordless Impact
q Cordless Drill
q Cutter
q Mallet
q Plusnut Tool
q Tape Measure
q T40 Torque Bit
q 3/8" Drill Bit
q 7/16" Socket
q 1/2" Socket
q 9/16" Wrench
q 3/16" Driver Bit
q Drill Stop
q 1" Hole Saw
q 1.1 Setup...................................................................................................................................................
q 1.2 Partition assembly...............................................................................................................................
3 - 4
5
Phase 1 - Assembly
q 2.1 Tips on how to attach a plusnut..........................................................................................................
q 2.2 Vehicle preparation..............................................................................................................................
q 2.3 Swing door partition installation..........................................................................................................
6
7
7 - 13
Phase 2 - Installation
WARNING
Before the installation, carefully read the supplied installation guide to avoid possible injuries and damages resulting from
incorrect installation. Always keep the installation guide in an accessible location at all times for reference during installa-
tion.
Installers must always wear appropriate safety gear during installation. This may include but is not limited to gloves, steel
toed shoes, and safety glasses.
Drilling is required to complete this install. Before drilling, ensure that you will not hit any critical parts of the vehicle like
the gas tank, wiring harness, or hose. Consult OEM vehicle or documentation as necessary. When drilling, use a drill
collar to reduce risk of damage to the vehicle.
This installation guide provides general installation instructions and best practices. However, various vehicles and prod-
uct install locations may require additional steps. It is the installers responsibility to ensure the install is safe and secure.
For further questions please contact us at 1-800-565-5321.
For technical support, contact us at 1-800-565-5321 C30-DL Installation Guide | REV. G2 | Page 3
PHASE 1 – ASSEMBLY
1.1 SETUP
1.1.2 Verify all parts are present.
Item No. Description Qty.
30-051 Top Bracket 1
30-052 Floor Bracket 1
30-500 Edge Trim ( QTY in Inches ) 45
70-007 Foam Tape ( QTY in Inches ) 18
6093 Grab Handle 1
79-932 Warning Label ( Bilingual ) 1
30-0720 Passenger Side Panel 1
30-0730 Driver Side Panel w/ Sliding Door 1
94-3001 Assembly Fastener Bag 1
94-6093 Assembly Fastener Bag 1
96-3001 Installation Fastener Bag 1
1.1.1 Unpack components; compare with the bill of materials.
30-500
30-051
70-007
30-052
30-0730
30-0720
6093
For technical support, contact us at 1-800-565-5321 C30-DL Installation Guide | REV. G2 | Page 4
1.1.3 Identify the Assembly and Installation fastener bags.
#90-200 Hex Bolt 5/16" × 1/2"
#98-116 Flat Washer
#94-116 Serrated Nut
#90-204 Hex Bolt 5/16" × 3/4"
#98-116 Flat Washer
#94-116 Serrated Nut
94-3001 Fastener Bag Hardware Assembly
96-3001 Fastener Bag Hardware Assembly
6093 Fastener Bag Hardware Assembly
#90-893 Cap Screw 1/4" × 3/4"
#94-112 Serrated Nut
#90-118 Hex Bolt 1/4" × 1-1/4"
#98-118 Lock Washer
#98-112 Flat Washer
#94-130 Plusnut .250
#98-118 Lock Washer
#98-112 Flat Washer
#94-130 Plusnut
#90-983 Double Ended Bolt
#94-100 Hex Nut
#98-180 Short Partition Spacer
#98-118 Lock Washer
#98-112 Flat Washer
#94-130 Plusnut
#90-984 Long Double
Ended Bolt
#94-100 Hex Nut
#98-181 Long Partition Spacer
For technical support, contact us at 1-800-565-5321 C30-DL Installation Guide | REV. G2 | Page 5
PHASE 1 – ASSEMBLY
1.2 PARTITION ASSEMBLY
1.2.1 Remove all the PVC from all the parts, then attach the edge trims on these locations.
Attach the grab handle to the passenger side panel.
EDGE TRIMS
EDGE TRIMS
1.2.2 Attach 5" foam tapes on the top, center and bottom of the door panel.
TOOLS
q Cutter
TOOLS
q Cordless Impact q 3/16" Driver Bit
q Mallet q Cutter
HARDWARE USED
#90-893 Cap Screw 1/4" × 3/4"
#94-112 Serrated Nut
For technical support, contact us at 1-800-565-5321 C30-DL Installation Guide | REV. G2 | Page 6
PHASE 2 – INSTALLATION
2.1 TIPS ON HOW TO ATTACH A PLUSNUT
FORWARD REVERSE
TIPS: Put the plusnut on the plusnut gun, then attach the plusnut in the hole by turning the gun forward until the
plusnut locks, then remove the gun by turning in reverse.
2.1.1 Attach the plusnut using the plusnut gun.
2.1.2 Attach the plusnut using the 6490 plusnut tool.
6490 HARDWARE USED
Flat washer 1/4"
Flat washer 1/4" BS × 3/4" OD
TOOLS
q Cordless Impact
q 7/16" Socket
q 9/16" Wrench
TIPS STEP 1:
Assemble the 6490 plusnut tool with the hardware needed,
plusnut and the 9/16" wrench as shown.
FORWARD REVERSE
TIPS STEP 2:
Attach the plusnut in the hole by turning
the bolt forward using an impact with a
7/16" socket until the plusnut locks, then
remove the bolt by turning the impact in
reverse.
NOTE: The hardware used for the 6490 plusnut tool is not included in the fastener bag.
The 6490 plusnut tool can be ordered separately upon demand at no charge.
For technical support, contact us at 1-800-565-5321 C30-DL Installation Guide | REV. G2 | Page 7
PHASE 2 – INSTALLATION
2.2 VEHICLE PREPARATION
2.2.1 Floor preparation.
Remove the two D-rings in the pillars, for
re-use.
TOOLS
q Cordless Impact
q T40 Torque Bit
PHASE 2 – INSTALLATION
2.3 STRAIGHT PARTITION INSTALLATION
2.3.1 Floor bracket installation.
Attach the oor bracket to the oor
re-using the 2 D-ring bolts.
HARDWARE USED
Use the D-ring bolt
TOOLS
q Cordless Impact
q T40 Torque Bit
For technical support, contact us at 1-800-565-5321 C30-DL Installation Guide | REV. G2 | Page 8
2.3.2 Attaching plusnuts.
NOTE: Put the partition in place and check if the holes of the partition align with the holes of the van.
TOOLS
q Plusnut Tool
# 94-130
Plusnut .250
HARDWARE USED
17×
Attach plusnuts in the 15 holes.
Put the assembled partition in place, then mark all the holes through the van.
TOOLS
q Cordless Drill q 3/8” Drill Bit or Step Drill q 1" Hole Saw
q Drill Stop
NOTE: For the B-pilar plastic cover and wood floor use 1" hole saw to
drill a hole in the B-pilar plastic cover or wood floor, then drill 3/8"
hole in the van.
• Enlarge all the holes in the van that align with the holes of the
partiton using 3/8” drill bit or step drill.
For technical support, contact us at 1-800-565-5321 C30-DL Installation Guide | REV. G2 | Page 9
2.3.3 Attach the top bracket to the van.
TOOLS
q Cordless Impact
q 7/16" Socket
HARDWARE USED
#90-118 Hex Bolt 1/4" × 1-1/4"
#98-118 Lock Washer
#98-112 Flat Washer
For technical support, contact us at 1-800-565-5321 C30-DL Installation Guide | REV. G2 | Page 10
TOOLS
q Cordless Impact
q 7/16" Socket
HARDWARE USED
2.3.4 Install double ended bolts and spacers into van before placing partition panels
TOOLS
q Cordless Impact
q 7/16" Socket
#94-130 Plusnut
#90-984 Double Ended Bolt
#98-181 Short Partition Spacer
HARDWARE USED
×
#94-130 Plusnut
#90-983 Double Ended Bolt
#98-180 Short Partition Spacer
For technical support, contact us at 1-800-565-5321 C30-DL Installation Guide | REV. G2 | Page 11
2.3.4 Put the side panels in place, then bolt the driver and passenger side panels to the van.
TOOLS
q Cordless Impact
q 7/16" Socket
#98-118 Lock Washer
#98-112 Flat Washer
#94-100 Hex Nut
HARDWARE USED
12×
For technical support, contact us at 1-800-565-5321 C30-DL Installation Guide | REV. G2 | Page 12
2.3.5 Attach the top bracket to the van.
TOOLS
q Cordless Impact
q 1/2" Socket
HARDWARE USED
#90-200 Hex Bolt 5/16" × 1/2"
#98-116 Flat Washer
#94-116 Serrated Nut
For technical support, contact us at 1-800-565-5321 C30-DL Installation Guide | REV. G2 | Page 13
2.3.6 Attach the driver and passenger side panels to the oor bracket.
HARDWARE USED
TOOLS
q Cordless Impact
q 1/2" Socket
#90-204 Hex Bolt 5/16" × 3/4"
#98-116 Flat Washer
#94-116 Serrated Nut
For technical support, contact us at 1-800-565-5321 C30-DL Installation Guide | REV. G2 | Page 14
2.3.7 Apply the warning label on the passenger side panel.
NOTE: English warning label is already
attached on the passenger
panel.
“You have successfully installed your partition,
Thank you for doing business with us.”
For any feedback or suggestions, you may have, please contact: [email protected]
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14

Ranger design C30-DL Installation guide

Category
Wall & ceiling mounts accessories
Type
Installation guide

Ranger design C30-DL is a straight partition specifically designed for Sprinter Vans that features a swing door made of steel. The C30-DL is easy to install and provides a secure and durable barrier within the vehicle. This partition is ideal for creating separate compartments within the van, enhancing privacy, security, and organization. Whether you need to divide the passenger and cargo areas, create a dedicated workspace, or isolate sensitive equipment, the Ranger design C30-DL offers a practical solution.

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI