Eks 2230 User guide

XSRING+

SHDSL switch

_________________

User’s guide

Document reference : 9018809-01

_________________

The XSRING+ SHDSL switch is manufactured by

ETIC TELECOM

13 Chemin du vieux chêne

38240 MEYLAN

FRANCE

TEL : + 33 4-76-04-20-00

FAX : + 33 4-76-04-20-01

e-mail : [email protected]

web : www.etictelecom.com

Hotline

TEL : + 33 4-76-04-20-05

FAX : + 33 4-76-04-20-01

e-mail : [email protected]

CONTENT

XSRING+ SHDSL switch User’s guide ref 9018809-01 Page 3

OVERVIEW

1 PRODUCTS IDENTIFICATION.........................................................................................................................................6

2 DATA-SHEET....................................................................................................................................................................8

3 PRODUCT OVERVIEW.....................................................................................................................................................9

3.1 Function................................................................................................................................................................9

3.2 Redundancy solutions: RSTP and proprietary failsafe ring..........................................................................10

3.3 The by-pass function.........................................................................................................................................11

3.4 Data rate versus distance..................................................................................................................................11

3.5 Ethernet ports.....................................................................................................................................................11

3.6 VLANs .................................................................................................................................................................12

3.7 Quality of service...............................................................................................................................................12

3.8 SNMP...................................................................................................................................................................12

3.9 Serial gateway....................................................................................................................................................12

3.10 Diagnostic functions..........................................................................................................................................12

3.11 Html configuration............................................................................................................................................12

INSTALLATION

1 DIMENSIONS..................................................................................................................................................................13

2 CONNECTORS ...............................................................................................................................................................13

3 LED INDICATORS ..........................................................................................................................................................17

4 DIN RAIL MOUNTING.....................................................................................................................................................18

5 COOLING........................................................................................................................................................................18

6 SUPPLY VOLTAGE........................................................................................................................................................18

7 ISOLATION AND GROUNDING.....................................................................................................................................18

8 RS232 INTERFACE ........................................................................................................................................................19

9 RS485 INTERFACE ........................................................................................................................................................19

10 DIGITAL INPUT AND OUTPUT......................................................................................................................................19

11 LINE CABLE ...................................................................................................................................................................20

12 PROTECTING THE SHDSL SWITCH FROM LIGHTNING............................................................................................21

13 CONNECTING THE SHDSL SWITCH TO THE LINE.....................................................................................................22

13.1 Point to point connection using two twisted pairs.........................................................................................22

13.2 Multidrop or ring connection............................................................................................................................22

13.3 By-pass function................................................................................................................................................23

14 INPUT AND OUTPUT......................................................................................................................................................23

CONTENT

Page 4 User’s guide ref 9018809-01 XSRING+ SHDSL switch

CONFIGURATION

1 SET UP STEPS...............................................................................................................................................................25

2 CONNECTING A PC TO THE XSRING+ FOR CONFIGURATION................................................................................26

2.1 Overview.............................................................................................................................................................26

2.2 First configuration .............................................................................................................................................26

2.3 Modifying the configuration from the LAN......................................................................................................27

3 REBOOTING THE XSRING+ AFTER PARAMETERS CHANGES................................................................................27

4 RECOVERING THE FACTORY CONFIGURATION......................................................................................................27

5 RESTRICTING ACCESS TO THE ADMINISTRATION SERVER..................................................................................27

6 RECOVERING A FREE ACCESS TO THE ADMINISTRATION SERVER....................................................................28

7 ASSIGNING AN IP ADDRESS TO THE LAN INTERFACE...........................................................................................28

8 IP ROUTING AND STATIC ROUTES............................................................................................................................28

9 SHDSL CONNECTION SET UP OVERVIEW.................................................................................................................30

9.1 Principle of operations......................................................................................................................................30

9.2 SHDSL connection profiles...............................................................................................................................31

10 SETTING UP A MULTIDROP OR RING SHDSL CONNECTION ..................................................................................32

10.1 Set up steps........................................................................................................................................................32

10.2 Step 1 : SHDSL connection set up...................................................................................................................32

10.3 Step 2 : SHDSL test and set up adjustment....................................................................................................33

11 SETTING UP A POINT TO POINT CONNECTION USING 2 TWISTED PAIRS............................................................34

11.1 Set up steps........................................................................................................................................................34

11.2 Step 1 : SHDSL connection set up...................................................................................................................34

11.3 Step 2 : SHDSL test and set up adjustment....................................................................................................36

12 RSTP REDUNDANCY PROTOCOL ...............................................................................................................................38

13 FAILSAFE RING REDUNDANCY PROTOCOL.............................................................................................................39

14 VLAN...............................................................................................................................................................................40

14.1 Overview.............................................................................................................................................................40

14.2 Set up..................................................................................................................................................................41

14.3 Html server and serial gateway ........................................................................................................................46

15 SNMP...............................................................................................................................................................................47

15.1 Overview.............................................................................................................................................................47

15.2 Setting up the SNMP function...........................................................................................................................47

15.3 Setting up the SNMP traps................................................................................................................................48

16 QUALITY OF SERVICE (QOS).......................................................................................................................................49

16.1 DiffServ benefits & overview.............................................................................................................................49

16.2 QoS set up..........................................................................................................................................................50

CONTENT

XSRING+ SHDSL switch User’s guide ref 9018809-01 Page 5

… CONFIGURATION

17 SERIAL GATEWAY ........................................................................................................................................................52

17.1 Modbus gateway................................................................................................................................................53

17.2 RAW TCP gateway.............................................................................................................................................56

17.3 RAW UDP gateway.............................................................................................................................................58

17.4 Multicast gateway ..............................................................................................................................................59

17.5 Unitelway gateway.............................................................................................................................................60

1 DIAGNOSTIC MENU.......................................................................................................................................................63

1.1 Log.......................................................................................................................................................................63

1.2 Network status ...................................................................................................................................................63

1.3 Statistics.............................................................................................................................................................63

1.4 Serial gateway....................................................................................................................................................64

2 STORING THE CONFIGURATION TO A FILE ..............................................................................................................65

3 RESTORING THE CONFIGURATION FROM A FILE....................................................................................................65

4 UPDATING THE FIRMWARE.........................................................................................................................................66

Appendix 1 : Data rate versus distance and cable quality

Appendix 2 : Html server description

OVERVIEW

Page 6 User’s guide ref 9018809-01 XSRING+ SHDSL switch

1 Products identification

Switch SHDSL XSRING+

XSRING+ 2400 2220 2230 BP2400 BP2220 BP2230

Min supply V. VDC 10 10 10 10 10 10

Max supply V. VDC 60 30 60 60 30 60

SHDSL ports 2 2 2 2 2 2

Max data rate * (Mb/s) 5.6 5.6 5.6 11.2 11.2 11.2

By-pass function N N N Y Y Y

Ethernet ports

10-100 Mb/s 4 2 2 4 2 2

RS232 0 1 2 0 1 2

RS485 2 wires 0 1 0 0 1 0

RSTP Y Y Y Y Y Y

Failsafe ring Y Y Y Y Y Y

VLAN, Y Y Y Y Y Y

SNMP Y Y Y Y Y Y

QoS DiffServ Y Y Y Y Y Y

Html Configuration Y Y Y Y Y Y

Serial gateway

RAW TCP & UDP

telnet,

modbus

unitelway

0 2 2 0 2 2

OVERVIEW

XSRING+ SHDSL switch User’s guide ref 9018809-01 Page 7

OVERVIEW

Page 8 User’s guide ref 9018809-01 XSRING+ SHDSL switch

2 Data-sheet

Dimensions 137 x 48 x 116 mm (h, l, d)

C.E.M EN50082-2

Electrical safety EN 60950

Lightning EN61000-4 et –5

Supply voltage XSRING+2400 or 2230 or BP2400 or BP2230 : 10 to 60 VDC

XSRING+2220 or BP2220 : 10 to 30 VDC

Consumption 6W

Operating T° -20°/ + 70°C non condensing

SHDSL ITU-T G.991.2, 802.3ah : 2BaseTL (EFM)

Data rate : 128 kb/s to 2.3 Mb/s with 2 wires

Latency : 4 ms

Ethernet 10/100 Mb/s Half / Full duplex Auto MDI/MDIX

Switch Store and forward – 1024 MAC @

IP Routing Static routes

RIP V2

QoS DiffServ compliant with RFC 2474, 2475, 2597, 2598

4 priority levels

SNMP RFC1213-MIB (MIB-2) / HDSL2-SHDSL-LINE-MIB / HOST-RESOURCES-MIB / IF-MIB

IP-MIB / BRIDGE-MIB / RSTP-MIB

VLAN IEEE 802.1Q

RS232-RS485 1200 to 115200 kb/s parity E/O/N

Raw TCP client and server

Raw UDP

Multicast

Modbus client and server

Unitelway

Telnet

Logs 300 events (date & time)

Configuration Managed mode : HTML browser

Unmanaged mode : DIP switches

OVERVIEW

XSRING+ SHDSL switch User’s guide ref 9018809-01 Page 9

3 Product overview

3.1 Function

The XSRING+ provides two SHDSL interfaces to extend Ethernet over a twisted pair.

The XSRING+ can be used in the following cases :

Daisy chain network

or

Daisy chain network using the

By-pass function (XSRING+BP

only)

Point to point transmission over

one or two twisted pairs to multiply

the data rate and provide a backup

link

Failsafe ring network using the

proprietary algorithm based on STP

Complex redundant topologies

using the RSTP algorithm

OVERVIEW

Page 10 User’s guide ref 9018809-01 XSRING+ SHDSL switch

3.2 Redundancy solutions: RSTP and proprietary failsafe ring

Industrial applications need reliable networks; one way to provide reliability is to provide backup paths

which form loops in the Ethernet network.

However, loops are highly unwelcome in Ethernet networks, as they can cause broadcast storms,

eating up all the available bandwidth and causing network outage.

The goal of redundancy protocols is to make Ethernet work of networks containing loops and to

provide a path at each time, even, if possible, when one or several links are in failure.

The XSRING provides two solution to handle redundancy :

RSTP

RSTP, standing for "Rapid Spanning Tree Protocol" is specified by the IEEE in the 802.1D-2004

document.

RSTP can handle complex structures ; RSTP can be used with devices from other manufacturers.

The failure detection delay and the recovery delay in an shdsl network is around 10 seconds.

Proprietary failsafe ring algorithm

Based on the STP algorithm, that solution makes possible to handle a ring structure up to 16 SHSDL

switches.

The advantages of that solution is that the failure detection delay and the recovery delay is only a few

seconds (One second if the ring counts 5 SHDSL switches); moreover, it is very simple to configure.

OVERVIEW

XSRING+ SHDSL switch User’s guide ref 9018809-01 Page 11

3.3 The by-pass function

When the network is a daisy chain – that case is very frequent in industrial applications - and when,

however, it is not possible to build a failsafe structure like a ring, the XSRING+BP offers a very useful

function called the “By-pass function”.

The XSRING+BP includes an electro-mechanical relay between both lines; that relay is automatically

closed to connect the two lines when the XSRING is switched off.

For instance, if the XSRING #2 cabinet is switched off for maintenance, for instance, the by-pass relay

inside the XSRING #2 will automatically connect the line coming from the XSRING #1 to the line going

to the XSRING #3.

After a few seconds, the XSRING #1 detects the connection default and establishes immediately the

connection with the XSRING #3.

In that way, the connection is recovered after a short delay between the XSRING+ #1 and the

XSRING+ #3.

3.4 Data rate versus distance

Each interface features an adaptive data rate from 128 Kb/s up to 5,7 Mb/s.

The data rate is a function of the cable quality and the distance with the next SHDSL switch. For

instance, the maximum distance between 2 switches through a line is 13 Km (8 miles) with a 0.9 mm

wire diameter cable.

The table in appendix 1 gives the data rate which can be expected over a line versus the length of the

line.

3.5 Ethernet ports

The XSRING provides 2 or 4 Ethernet RJ45 interfaces (depending on the product reference).

OVERVIEW

Page 12 User’s guide ref 9018809-01 XSRING+ SHDSL switch

3.6 VLANs

The XSRING features VLAN per port :

Each Ethernet port can be assigned to a particular VLAN. A device connected to an Ethernet port

belonging to a particular VLAN can communicate only with devices connected to Ethernet ports

belonging to the same one.

3.7 Quality of service

The product provides “DiffServ” quality of service functionality to give transmission priority to critical

applications.

Devices TCP ports and IP addresses are classified in 4 priority classes.

A minimum and a maximum bandwidth is allocated to each class.

3.8 SNMP

3.9 Serial gateway

The XSRING –1220, -1230, -2220 or –2230 feature a 2 ports serial gateway.

The gateway features raw TCP client and server, raw UDP, modbus client and server, telnet and

multicast.

3.10 Diagnostic functions

The XSRING html server provides diagnostic pages giving the guarantee the transmission quality is

what it has to be.

3.11 Html configuration

The XSRING can be configured either with an html browser if advanced functions are necessary

(QoS, RS gateway, diagnostic …).

It can be configured with a few DIP switches for simple unmanaged applications.

INSTALLATION

Page 13 User’s guide ref 9018809-01 XSRING+ SHDSL switch

1 Dimensions

2 Connectors

XSRING+2400 XSRING+2220

XSRING+2230

INSTALLATION

Page 14 User’s guide ref 9018809-01 XSRING+ SHDSL switch

XSRING+BP2400 XSRING+BP2220

XSRING+BP2230

INSTALLATION

XSRING+ SHDSL switch User’s guide ref 9018809-01 Page 15

Push-button :

A push-button is located close to the DIP switches.

It enables to restore the factory profile.

To restore the factory profile, switch the power on while pressing the push-button until the

OPERATION led turns green.

Attention : Once the factory profile has been restored, the stored configuration is lost.

2 positions screw terminal : Supply voltage 1

Protected against reverse polarity

Position Signal Function

1 Power 1 + 10-30 VDC : XSRING+2220 & XSRING+BP2220

10-60 VDC : XSRING+2400 XSRING+2230 XSRING+BP2400 XSRING+BP2230

2 Power 1 - 0V isolated from the enclosure

2 positions screw terminal : Supply voltage 2

Protected against reverse polarity

Position Signal Function

1 Power 2 + 10-30 VDC : XSRING+2220 & XSRING+BP2220

10-60 VDC : XSRING+2400 XSRING+2230 XSRING+BP2400 XSRING+BP2230

2 Power 2 - 0V isolated from the enclosure

4 positions screw terminal :Digital input and output

Position Signal Function

1 3V3 3 V DC provided by the XS+

2 In Digital input

3 F + Digital output + (max 50Vdc - 0,6A)

4 F - Digital output -

XSRING+2220 XSRING+2230 XSRING+2400

2 positions screw terminal : Shdsl 1 & Shdsl 2

Position Signal Function

1 Line SHDSL line conductor (the two wires can be inverted)

2 Line SHDSL line conductor (the two wires can be inverted)

XSRING+BP2220 XSRING+BP2230 XSRING+BP2400

2 positions screw terminal : Shdsl 1 & Shdsl 2

Position Signal Function

1 Line SHDSL line conductor if the by-pass function is not used

2 Line SHDSL line conductor if the by-pass function is not used

XSRING+BP2220 XSRING+BP2230 XSRING+BP2400

2 positions screw terminal : Shdsl 1 by-pass & Shdsl 2 by_pass

Position Signal Function

1 Line SHDSL line conductor if the by-pass function is used

2 Line SHDSL line conductor if the by-pass function is used

RJ45 connector : Ethernet

Position Signal Function

1 Tx + Emission polarity +

2 Tx - Emission polarity -

3 Rx + Reception polarity +

4 N.C -

5 N.C -

6 Rx - Reception polarity -

7 N.C. -

8 N.C. -

INSTALLATION

Page 16 User’s guide ref 9018809-01 XSRING+ SHDSL switch

2 positions screw terminal : RS485

Position Signal Function

1 A RS485 polarity A

2 B RS485 polarity B

RS232 RJ45 connector

(To connect a DCE to the RS232 port)

Position Circuit Direction Function

1 DTR - 108 OUT Data terminal ready

2 TD - 103 OUT Data Emission

3 RD - 104 IN Data Reception

4 DSR - 107 IN Data set ready

5 SG - 102 - Ground

6 Not used OUT -

7 CTS - 106 IN Clear to send

8 RTS - 105 OUT Request to send

RS232 : RJ45 connector

(To connect a DTE to the RS232 port)

Pin Circuit Direction Function

1 CD - 109 OUT Carrier detect

2 RD - 104 OUT Data Reception

3 TD - 103 IN Data Emission

4 DTR - 108 IN Data terminal ready

5 SG - 102 - Ground

6 DSR - 107 OUT Data set ready

7 RTS - 105 IN Request to send

8 CTS - 106 OUT Clear to send

RS232 : RJ45 connector

(To connect a DTE to the RS232 port)

Pin Circuit Direction Function

1 CD - 109 OUT Carrier detect

2 RD - 104 OUT Data Reception

3 TD - 103 IN Data Emission

4 DTR - 108 IN Data terminal ready

5 SG - 102 - Ground

6 DSR - 107 OUT Data set ready

7 RTS - 105 IN Request to send

8 CTS - 106 OUT Clear to send

INSTALLATION

XSRING+ SHDSL switch User’s guide ref 9018809-01 Page 17

3 Led indicators

Led Status Description

1 ON green The supply voltage 1 is present

2 ON green The supply voltage 2 is present

ON green The unit is ready

ON red At power on : The product is starting

Otherwise : Product failure

ON green Failsafe ring mode / the ring is established

ON red Failsafe ring mode / a failure has been detected

OFF The XSRING+ is not in the failsafe ring mode

Flashing slowly SHDSL connection

ON SHDSL connection established

Shdsl 1

Shdsl 2

Flashing quickly SHDSL connection established ; traffic across the line

RS232 * RX Flashing quickly Bytes received from the RS232

RS232 * TX Flashing quickly Bytes transmitted to the RS232

RS485 ** RX Flashing quickly Bytes received from the RS485

RS485 ** TX Flashing quickly Bytes received to the RS485

* XSRING+2220, XSRING+2230 XSRING+BP2220, XSRING+BP2230

** XSRING+2220, XSRING+BP2220

INSTALLATION

Page 18 User’s guide ref 9018809-01 XSRING+ SHDSL switch

4 DIN rail mounting

Mounting the unit on the DIN rail

This unit should be mounted on 35 mm DIN-

rail, horizontally mounted.

Removing the unit from the DIN rail

5 Cooling

To avoid obstructing the airflow around the unit, the spacing must be at least 25 mm above and below, and 10 mm left and

right.

6 Supply voltage

XSRING+2400, XSRING+BP2400 : 10 to 60 VDC

XSRING+2230, XSRING+BP2230: 10 to 60 VDC

XSRING+2220, XSRING+BP2220 : 10 to 30 VDC

Power consumption : 6 W

The product is protected against the inversion of the polarity of the supply voltage.

7 Isolation and grounding

The enclosure of the product is metallic; It must be grounded.

The minus polarity of the supply voltage is common with the minus voltage of the electronic board –

usually called 0 V - and is isolated from the enclosure.

Moreover, the Ethernet signal and the SHDSL signal are isolated through transformers. It is why

• the versions XSRING+2400 and XSRING+BP2400 are fully isolated. The common mode voltage must not exceed 1500 V.

• The versions XSRING+2220 and XSRING+BP2220 provide the minus voltage through the RS232 interface and through

the RS485 interface.

• The versions XSRING+2230 and XSRING+BP2230 provide the minus voltage through the RS232 interface.

INSTALLATION

XSRING+ SHDSL switch User’s guide ref 9018809-01 Page 19

8 RS232 interface

The RS232 data rate can be tuned from 1200 to 115200 b/s with parity (even / odd) or no parity.

The data terminal must be less than 10 meters far from the modem.

Cables can be provided to connect the product to DTE and DCE as follows :

RS232 cables (L=1m)

Code User connector Cable function

CAB592 SubD 9 male To connect a DCE to the XSRING+

CAB593 SubD 9 female To connect a DTE to the XSRING+

CAB609 Wires To connect a device providing a specific connector

9 RS485 interface

The RS485 serial interface is provided on the front

panel 2 pins screw-block.

Polarisation resistors

Two 10 Kohm bus polarisation resistors are included

inside the product.

Remark :

The RS485 interface of the XSRING+1220 or 2220 is made for connecting only one device at short

distance, inside the same cabinet for instance, and at low data rate up to 19200 b/s.

If the RS485 line has to be longer, one of the devices connected to the RS485 line must provide

standard polarisation resistors, and a 150 Ohm termination resistor must be connected at each end of

the line.

10 Digital input and output

Digital output :

Max. voltage : 48 VDC

Max. current : 500 mA

Digital input :

Maximum voltage : 20 VDC

RS485

+-

B(+) A(-)

10 KOhm 10 KOhm

F+ F-

78

Digital output

+

-

V < 48 VDC

I < 0,5 A

3V3 In

56

Digital input

I max = 0,5 A

V

IPL router

INSTALLATION

Page 20 User’s guide ref 9018809-01 XSRING+ SHDSL switch

11 Line cable

Twisted pair

The XSRING+ shdsl switch is designed to be connected to one or several telephone grade twisted

pairs.

The conductor diameter must be included between 0.4 mm and 1 mm.

Shielded cable

It is better to use a shielded cable.

The shield must be connected to the earth at one of its ends.

The shield decreases the influence of the electromagnetic ambient noise on the shdsl signal.

Moreover, the shield protects the XSRING+ shdsl switch against lightning.

Electrical power cable

Two power conductors can be used instead of a twisted pair to set an shdsl connection.

However, because the two wires are not twisted, the ambient electrical noise may disturb the

transmission.

Compared to the transmission over a twisted pair, the maximum distance between two SHDSL

switches is decreased.

Cross talk

If the cable is made of several pairs, each pair can be used to transmit a particular shdsl connection ;

however the shdsl signal transmitted in one pair may disturb the shdsl signal transmitted in another

one, and, in some cases, may decrease the effective data rate of both shdsl connections.

Page is loading ...

Eks 2230 User guide

This manual is also suitable for

Eks 2230 User guide

Related papers

Other documents