2. Troy-Bilt
  3. Troy-Bilt 2800 PSI pressure washer
Troy-Bilt 2800 PSI pressure washer

Troy-Bilt Troy-Bilt 2800 PSI pressure washer User manual

  • Hello! I've reviewed the user manual for the Troy-Bilt 2800 PSI pressure washer and I'm ready to help you with any questions you might have. The manual covers the assembly, features, controls, and specifications, including the high-pressure and detergent systems.
  • How much does the Troy-Bilt 2800 PSI pressure washer weigh?
    What is the maximum flow rate of water that can be produced by this Troy-Bilt 2800 PSI pressure washer?
    Is there an engine oil dipstick on this Troy-Bilt 2800 PSI pressure washer?
Troy-Bilt
2800 PSI pressure
washer
USER MANUAL
Assembly
Unpack Pressure Washer
1. Remove the parts bag, accessories, and inserts included with pressure washer.
2. Open carton completely by cutting each corner from top to bottom.
3. Ensure you have all included items prior to assembly.
Items in the carton include:
● Main Unit with Cleaning Tank
● Handle
● High Pressure Hose
● Spray Gun
● Nozzle Extension with Quick Connect Fitting
● Plastic Accessory Tray
● Oil Pouch
● Engine Operator’s Manual
● Parts Bag (which includes the following):
● Operator’s Manual
● Bag of 5 Multi–Colored Quick Connect Spray
Assembly
Attach Handle and Accessory Tray
1. Place handle (A) onto handle supports connected to main unit. Make sure holes in handle
align with holes on handle supports.
2. Insert handle carriage bolts (B) through holes from inside of unit and attach a plastic knob (C)
from outside of unit. Tighten by hand.
3. Place accessory tray (D) over holes (E) on handle (viewing from front of unit). Push the tree
clips (F) into the holes until they sit flat against the accessory tray.
Assembly
Lubricate O-Rings
Lubrication of o-rings is extremely important for installation and operation. The use of a lubricant (petroleum
or synthetic grease) during assembly helps seat o-rings properly and provides an improved seal. It also helps
protect the o-ring from damage by abrasion, pinching or cutting and extends the life of the o-ring.
Lubricate all connections shown below, following these instructions:
1. Inspect and clean connecting surfaces prior to lubrication and assembly.
2. 2. Use lubricants sparingly during assembly; a light film is all that is required.
3. Use a small brush or cotton swab to apply grease directly to o-rings where they are not accessible (QC
fitting, M22 fitting).
Features and Controls
Read this Operator’s Manual and safety rules before operating your pressure washer.
Compare the illustrations with your pressure washer, to familiarize yourself with the locations
of various controls and adjustments. Save this manual for future reference.
● A - Spray Gun — Controls the application of water onto cleaning surface with trigger
device. Includes trigger lock.
● B - Recoil Starter — Used for starting the engine manually.
● C - Oil Fill/Dipstick — Check and fill with oil here.
● D - Engine Identification — Provides model, type and code of engine. Please have
these readily available if calling for assistance.
● E - High Pressure Outlet — Connection for high pressure hose.
● F - Water Inlet — Connection for garden hose.
● G - Pump — Develops high pressure.
● H - Automatic Cool Down System — Cycles water through pump when water reaches
125°-155°F (51°C-68°C). Warm water will discharge from pump onto ground. This
system prevents internal pump damage.
Features and Controls
● J - Cleaning Tank — Use to hold up to 0.5 gallons (1.9 liters) of pressure washer
detergent.
● K - Identification Label — Provides model and serial number of pressure washer.
Please have these readily available if calling for assistance.
● L - Air Filter — Protects engine by filtering dust anddebris out of intake air.
● M - Warning/Operating Instructions Tag — Identifies hazards and proper procedure to
start/ stop pressure washer.
● N - Fuel Tank — Fill tank with regular unleaded fuel. Always leave room for fuel
expansion.
● P - Nozzle Extension with Quick Connect — Allows you to switch between five different
spray tips.
● R - High Pressure Hose — Connect one end to water pump and the other end to spray
gun.
● S - Accessory Tray — Provides convenient storage for standard and optional
accessories, such as brushes, turbo wands, etc.
● T - Spray Tips — Jet soap, Jet flush, 0°, 25° and 40°: for various high pressure
cleaning applications.
Features and Controls
INTRODUCTION
The Troy-Bilt 2800 PSI pressure washer is a powerful cleaning tool designed to tackle a variety of
outdoor cleaning tasks. Whether you need to clean your driveway, deck, patio, siding, or vehicles,
this pressure washer provides the water pressure and flow necessary to remove dirt, grime, and
stains effectively.
With a maximum pressure of 2800 PSI (pounds per square inch) and a water flow rate of around
2.3 to 2.5 gallons per minute (GPM), the Troy-Bilt 2800 PSI pressure washer delivers strong and
consistent power to help you achieve professional-level cleaning results. The high-pressure water
stream generated by the machine can strip away tough stains, grease, mildew, and other stubborn
debris
Equipped with a reliable gasoline-powered engine, this pressure washer offers the convenience of
portability, allowing you to move freely without the limitations of a power cord. The engine's
displacement can vary depending on the specific model, ensuring that you have ample power to
tackle your cleaning tasks effectively.
Here are the specifications for the Troy-Bilt 2800 PSI pressure washer:
SPECIFICATION
●Maximum Pressure: 2800 PSI (pounds per square inch)
●Water Flow Rate: Approximately 2.3 to 2.5 gallons per minute (GPM)
●Engine Type: Gasoline-powered engine
●Engine Displacement: Varies depending on the model (e.g., 160cc, 190cc, etc.)
●Pump Type: Axial cam pump or triplex pump (varies based on the model)
●Nozzles: Includes a set of quick-connect nozzles with different spray patterns, such as
0-degree, 15-degree, 25-degree, 40-degree, and a soap applicator nozzle
●Hose Length: Typically around 25 feet
●Detergent System: Equipped with an onboard detergent tank for easy application of cleaning
solutions
●Wheels: Features large, durable wheels for improved mobility
●Frame: Constructed from sturdy materials like steel or aluminum
●Weight: The weight of the pressure washer may vary, but it generally falls between 50 to 70
pounds
●Additional Features: Depending on the model, it may include features like a pressure
regulator, low-oil shutdown (for gas-powered models), quick-connect fittings, foldable handles
for convenient storage, and a built-in hose reel.
●What is the difference between the Troy-Bilt 2800 PSI pressure washer and the Troy-Bilt 2400 PSI
pressure washer?
The Troy-Bilt 2800 PSI pressure washer is a more powerful version of the Troy-Bilt 2400 PSI pressure washer.
●How much does the Troy-Bilt 2800 PSI pressure washer weigh?
The Troy-Bilt 2800 PSI pressure washer weighs about 50 pounds.
Manuals.plus
● What is the maximum flow rate of water that can be produced by this Troy-Bilt 2800 PSI pressure washer?
The maximum flow rate of water that can be produced by this Troy-Bilt 2800 PSI pressure washer is 3.2
gallons per minute.
●What are some of the accessories that are included with this Troy-Bilt 2800 PSI pressure washer?
Some of the accessories that are included with this Troy-Bilt 2800 PSI pressure washer include a detergent
tank, a 25 foot high pressure hose, a 25 foot low pressure hose, a 25 foot power cord, and an owner's manual.
●Is there an engine on/off switch on this Troy-Bilt 2800 PSI pressure washer?
Yes, there is an engine on/off switch on this Troy-Bilt 2800 PSI pressure washer.
Manuals.plus
● Is there an engine oil dipstick on this Troy-Bilt 2800 PSI pressure washer?
Yes, there is an engine oil dipstick on this Troy-Bilt 2800 PSI pressure washer.
/