Steelmate BOT251 User manual

Brand
Steelmate
Model
BOT251
Type
User manual

Steelmate BOT251 is a seat belt detection kit designed to remind drivers to take their baby with them whenever they leave the car. It features an easy-to-install design, programming mode for customization, and low battery warnings to ensure optimal functionality. The sensor belt detection kit monitors seat belt buckles with an inner wall thickness of 7mm and can be programmed to work with up to 2 sensor pads. It is suitable for vehicles with CIG lighters that have electricity after flame out. The BOT251 operates on DC 3V (2V~3.

Steelmate BOT251 is a seat belt detection kit designed to remind drivers to take their baby with them whenever they leave the car. It features an easy-to-install design, programming mode for customization, and low battery warnings to ensure optimal functionality. The sensor belt detection kit monitors seat belt buckles with an inner wall thickness of 7mm and can be programmed to work with up to 2 sensor pads. It is suitable for vehicles with CIG lighters that have electricity after flame out. The BOT251 operates on DC 3V (2V~3.

Seat belt detection kit
(To be pasted on the inside
of the driver’s seat belt)
Stick on the inside of the
driver's driver’s seat belt slot
Stick on the inside of the
driver's seat belt slot
7 8 9
Buckle the driver’s seat belt The display “Bi” once to
indicate the seat belt is buckled
65
Buckle the driver’s seat belt The display “Bi”
once to indicate the
seat belt is buckled
3
4
Display will “Bi” twice immediately
to enter working mode
The display will flashing in turn
with red & green lights until baby
left the car seat or the display
is turn off.
7 8
1
Unbuckle the driver’s seat belt
2 3
The display “Bi” once to indicate
the seat belt is unbuckled
The display will flashing in turn with
red & green lights until baby left the
car seat or the display is turn off.
4
5. Baby is remained on the car seat after unbuckle the driver’s seat belt:
7. Baby didn’t sit on the car seat more than 15 minutes after ACC ON:
If sensor pad in low battery status
ACC ON, and baby sit on the car seat, when the system detectsthe sensor pad is in low battery
status, the display will warning and yellow light flashing for 3 times, then the light will return to green,
and the system will back to the working mode.
If seat belt detection kit in low battery status
Buckle the seat belt, when the system detects seat belt detection kit is in low battery status, the
display will warning and yellow light flashing once, then the light will return to green, and thesystem
will back to the working mode.
1
Buckle the driver’s seat belt,
then unbuckle it
After all parts are programmed, hold “SET” button, Then the display will warning to save and
exit the programming mode.
Note: 1.Only 2 sensor pads and 1 seat belt detection kit can be up to programmed.
2.If there is no operation within 2 minutes, the system will exit the programming mode
automatically.
The display will "Bi" once with
yellow light flashing, then enter
the next programing
The display will “Bi” twice with
green light flashing, then enter
the next programing.
DC 3V (2V~3.6V
DC 3V (2V~3.6V
>20N
Seat belt detection kit
The display and sensor belt detection kit are not programmed.
The seat belt buckles with inner wall thickness 7mm will affect the use of this part.
The sensor belt detection kit battery is low, please change to new sensor belt detection kit.
3. Sensor belt detection kit not work
2~36kg.
The system is also suitable for the vehicle with the CIG lighter has the electricity after flame out, but
must be equipped with seat belt detection kit.
The sensor belt detection kit is only suitable for seat belt buckles with inner wall thickness 7mm.
If not, may lead to seat belt buckle monitoring failure.
1. This system is designed for reminding drivers to take their baby with them whenever
they leave the car.
2. STEELMATE does not take any responsibility for any accident happen because of
negligence.
3. This system is designed for a reminder purpose only, not a lifesaver.
4. Before using this system, please read the manual carefully.
9
The vehiclewith the CIG lighter has the electricity after flame out, must be equipped with seat
belt detection kit.
4.
5.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10

Steelmate BOT251 User manual

Brand
Steelmate
Model
BOT251
Type
User manual

Steelmate BOT251 is a seat belt detection kit designed to remind drivers to take their baby with them whenever they leave the car. It features an easy-to-install design, programming mode for customization, and low battery warnings to ensure optimal functionality. The sensor belt detection kit monitors seat belt buckles with an inner wall thickness of 7mm and can be programmed to work with up to 2 sensor pads. It is suitable for vehicles with CIG lighters that have electricity after flame out. The BOT251 operates on DC 3V (2V~3.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Other documents