SPECIFICATIONS
Photo recording
Photo resolution 36 / 24 / 20 / 16 / 12 / 8 /5 / 3 MP
File format JPEG
Time lapse mode 5min/30min/60min
Multi-shot mode Up to 10 photos per detection
Stamp(photos and video) date,time,temperature
Capture mode Camera/Video/Camera&video/
Time lapse
Video recording
Video resolution 4K/2.7K /1080P / 720P / 480P / 240P
File format AVI
Video length 3s~10 minutes
Capture mode Colorful mode at daytime,
black and white mode at night
Memory storage
Support Internal memory:none
External memory:Micro SD card
(up to 256GB )
Power source
Alkaline Battery 1.5V AA Battery*8
External Power Jack DC6V/2Aor1.5A (3.5x1.35 mm)
Detection system
Motion Sensor three PIRS
Detection Angle 120°
Detection Range 15M during the day/10M
at night
Trigger Speed 0.3 second
Delay between each detection 5 s~ 60min
Night time illumination system
Infrared LEDS 42PCS NO Glow LEDS
Recommendations
Operating temperature
(4℉to+158℉)(-20℃to+70°C)
Waterproof level
P65
Button function introduction
1.Settings area
MENU：Enter menu and return
REPLAY：View pictures and videos
SHOT ：Enlarge the picture to view, use this key to
zoom in and need to zoom out, press the "OK" key
below
OK：Confirm
2.mode switch
OFF：When the camera does not need to work, you
need to slide the button to “OFF”
TEST：When setting the camera and viewing pictures,
please slide the button to "TEST"
ON：The camera needs to work, slide the button to
"ON"
INSTALLATION
Step 1
Open the battery cover and Install 4 or 8 AA
batteries following to the positive and
the negative battery sign. Close the battery
cover to resist water and dust.
NOTICE
Video recording will consume significantly
more power than taking photo.
especially at night with IR LED on.Please set
a shorter vide Length to ensure battery life
EXTERNALPOWERSUPPLY
Use 6V DC Power source(Not included)
The size of the hole is 3.5*1.35MM
Step 2
Insert Micro SD memory card to HC-812 Trail
Camera
supports Max 256 GB
NOTICE
Before you insert or remove the memory card,the
camera power switch must be turned to "OFF".Failing
to do so may causes loss of files or damage the
pictures that already recorded in the memory card.
Step 3
Slide the mode swith to :“TEST”
Step 4
1.The screen lights up and enters the
operation settings
2.Please format the memory card when
using it for the first time
Setup introduction
Mode：
Photo, Video, Photo+Video, choose whether
to take a photo or video when motion is
detected. In "Photo + Video" mode, the
camera takes the set number of photos first,
and then records the video
Photo resolution：
Select the desired resolution for photos.A
higher resolution produces a somewhat
better photo quality but results in larger files
requiring more space on the memory card.
Photo series：
1/2/3/10 available.You can set the number of
photos taken after an
animal is detected
Video resolution
Select the required video resolution.A higher
resolution produces higher quality videos
but results in larger files requiring more
space on the memory card.Videos are
recorded in AVI format which can be played
back on most video devices.
Video length：
Default 5 seconds,and you can also choose
30s,60s,90s.Specify the duration of a video
recording when the camera is triggered
automatically
Shot lag
The minimum IR trigger interval is 5 seconds
and the maximum is 60 minutes. According
to the shooting scene settings, the camera's
default setting is 5 seconds
Time lapse
If you want to record the process of blooming
flowers, the "time lapse" mode can be use. The
camera automatically records at the set time
(Notification: Infrared Motion sensors
deactivated)
Time & Date
Press the up, down, left and right keys to
adjust the date and time. Time setting can
choose 12-hour format or 24-hour format
Endless Capture
If"YES",it won't stop recording when the SD
card is full,but will delete the oldest
videos/photos.
If “NO”,it will stop recording when the SD
card is full.
Step 5
1. Camera working mode
After the setting is completed, slide the
setting key to the "ON" mode,A 15-second
countdown appears on the screen, and the
LED indicator starts to flash, the countdown
ends, the red light turns off, and the machine
enters the working state
2. view image
2.1 To view the picture on the camera screen,
please slide the mode switch to TEST mode,
press the “REPLAY” button to display the
picture, press the up and down keys to view
the picture.
2.2 or slide the mode switch to“TEST”,
connect the camera with one end of the
USB cable, and connect the other end
to the computer, then open the file
transferred by USB on the computer to
view the pictures taken
2.3 . Or take out the memory card in the
camera, plug it into the computer port
with the SD card adapter, and view the
pictures on the computer
Trouble Shooting
Q:Power on
A:When all the setting completed,slide power
switch from “TEST” to” ON”(The camera light
flashes only once).The camera powers on and
captures image or videos when animals or
people are detected by its PIR
The camera will stay asleep to save power,if no
animals are detected.
Q:How to let the camera capture the
object of interest?
A:1.Check the PIR,if it damaged or covered by
leaf,camera will not be triggered.
2.Try to set your camera up in an area where no
heat resources are in the camera's field of view.
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
/
