Fire Magic Aurora Firebox Liner Kit (Pre HSI) User manual

Fire Magic
Brand
Fire Magic
Model
Aurora Firebox Liner Kit (Pre HSI)
Category
Barbecues & grills
Type
User manual

This manual is also suitable for

REV 0 - 1512070825
L-C2-474
1
ROBERT H. PETERSON CO. • 14724 East Proctor Avenue • City of Industry, CA 91746
Table 1
Liner back
2
Liner right
5
Firebox Liner Kit
Model Part No.
Parts List
Firebox
liner pieces
Burner
igniter *
Flash
tube
Air
baffl e
Drive
screw
†
Self-tapping
hex screw
Flavor
grid *
A790
24180-RLK
53311263
A660
24170-RLK
53311263
A540
24150-RLK
53311263
A530
24125-RLK
52211242
A430
24130-RLK
52211242
Flash
tube
*
Not shown
† Includes 4 extra
drive screws
LINER
CENTER
1
LINER
BACK
2
LINER
LEFT
4
Model # 24180-RLK
24170-RLK
24150-RLK
24125-RLK
24130-RLK
Liner center
1
Liner Front
3
Drive screw
A660 kit shown
Self-tapping
hex screw
Air baffl e
6
Liner left
4
This fi rebox liner kit is for installation on Aurora grills with spark ignition only. Installation on an A660 is depicted
in this instruction.
READ THESE INSTRUCTIONS CAREFULLY BEFORE STARTING INSTALLATION.
Tools required: Gloves, Phillips screwdriver, rubber mallet, pliers, needle-nose pliers, hammer, and a
1
/4" nut
driver (or equivalent).
Be sure the grill is completely cool and the gas is completely shut off.
IMPORTANT: CLEAN THE INTERIOR OF THE GRILL OF ALL DEPOSITS AND GREASE PRIOR TO
INSTALLING THE FIREBOX LINER KIT.
Note: Wear gloves whenever installing and handling this liner kit as some components have sharp edges.
Remove the warming rack, cooking grids, fl avor grids, burners, burner igniters, I.R. burners (if applicable),
I.R. burner igniters (if applicable), air baffl e, and fl ash tubes. Open the control panel. Reference your owner's
manual for removal details if needed.
Note: The fl avor grids, burner igniters, the air baffl e, and fl ash tubes that are being removed from your grill
are no longer needed and may be discarded. The items included in this kit will replace these parts.
I
REV 0 - 1512070825
L-C2-474
2
New left
liner
New liner
fl ange
Existing
fi rebox
CORRECT
INCORRECT
New
liner
fl ange
Existing
fi rebox
ng
ti
New left
liner
Install rear liner
Procedure continued on next page
Place the rear liner (item 2) ensuring it rests fl at against
grill rear fi rebox wall. The two tabs (on center liner) must
extend up through the slots in the rear liner.
Note: If needed, use a rubber mallet to assist in
proper placement of liner panels.
Place the center liner (item 1 of parts list) onto the grill
drainage channel. Ensure the liner rests fl at in place.
Note: It is recommended to slightly bend the 4 tabs
inward to assist in front and rear liner installation.
LINER
CENTER
1
LINER
BACK
2
Tabs must clear the openings
Place the front liner (item 3) ensuring it rests fl at against
the grill front fi rebox wall, and the two tabs (on center liner)
extend up through the slots in the front liner.
Install front
liner
LINER
CENTER
1
LINER
FRONT
3
Tabs must clear
the openings
LINER
BACK
2
Place the left liner (item 4) as shown above. Rest the liner
OVER the front and rear liner fl anges (hiding the fl anges)
and ensure the 4 holes are aligned with the 4 grill wall rivets.
To secure the liner, align each drive screw (included in kit)
with the corresponding hole and carefully hammer each
drive screw into the panel. Use needle-nose pliers to assist
in holding the drive screws properly.
Note: The drive screw will force out the center of
the existing rivet. Therefore, ensure to use
ample force when driving the screw through
the retaining rivet.
REPEAT THIS STEP FOR THE RIGHT LINER (item 5).
IV
Place left liner
LINER
LEFT
4
III
V
Install
center
liner
LINER
CENTER
1
The drive screws
must be aligned
when hammering
LINER
CENTER
1
LINER
FRONT
3
LINER
BACK
2
II
REV 0 - 1512070825
L-C2-474
3
VI
Using pliers, bend in the four tabs inward toward the middle
of the center liner to lock the liner panels together.
Bend
tabs inward
LINER
CENTER
1
LINER
FRONT
3
LINER
BACK
2
Place the air baffl e as shown above. To properly install, the
tabs must slide into the slots located on the liners.
VIII
Install the new igniters, then re-install the burners, infrared
burner igniters (if applicable), infrared burners (if applicable),
new fl avor grids, the control panel, cooking grids, and
warming rack. Refer to your owner's manual for installation
details if needed.
IX
Install the new fl ash tube by aligning the fl ash tube over
the original liner mounting holes. Using a
1
/4" nut driver,
affi x the fl ash tube with the supplied hex screws. Repeat
this procedure for the other fl ash tubes.
Flash
tube
VII
x 2
(per fl ash tube)
REV 0 - 1512070825
L-C2-474
4
NOTES PAGE
Please use this page to record any information about your unit that you may want to have at hand.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4

Fire Magic Aurora Firebox Liner Kit (Pre HSI) User manual

Fire Magic
Brand
Fire Magic
Model
Aurora Firebox Liner Kit (Pre HSI)
Category
Barbecues & grills
Type
User manual
This manual is also suitable for
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents