DeWalt DWS7085 User manual

Type
User manual

The DeWalt DWS7085 Heavy-Duty Miter Saw LED Worklight System is designed for use with DEWALT miter saws. It features a 3.3 V DC LED light, providing bright and accurate illumination of the work area. The worklight is powered by a 120-240 V AC, 50/60 Hz power supply and has an operating temperature range of 32°F to 104°F (0°C to 40°C). It is water-resistant and has an ON/OFF switch for convenient control.

The DeWalt DWS7085 Heavy-Duty Miter Saw LED Worklight System is designed for use with DEWALT miter saws. It features a 3.3 V DC LED light, providing bright and accurate illumination of the work area. The worklight is powered by a 120-240 V AC, 50/60 Hz power supply and has an operating temperature range of 32°F to 104°F (0°C to 40°C). It is water-resistant and has an ON/OFF switch for convenient control.

DWS7085 Heavy-Duty Miter Saw LED Worklight System
Système de lampe de travail à DEL pour scie à onglets robuste DWS7085
Sistema de luz de trabajo LED para sierra ingletadora DWS7085
INSTRUCTION MANUAL
GUIDE D’UTILISATION
MANUAL DE INSTRUCCIONES
INSTRUCTIVO DE OPERACIÓN, CENTROS DE SERVICIO Y PÓLIZA
DE GARANTÍA. ADVERTENCIA: LÉASE ESTE INSTRUCTIVO
ANTES DE USAR EL PRODUCTO.
If you have questions or comments, contact us.
Pour toute question ou tout commentaire, nous contacter.
Si tiene dudas o comentarios, contáctenos.
1-800-4-DEWALT • www.dewalt.com
English
1
IF YOU HAVE ANY QUESTIONS OR COMMENTS ABOUT
THIS OR ANY D
EWALT TOOL, CALL US TOLL FREE AT:
1-800-4-D
EWALT (1-800-433-9258)
Safety Instructions for Worklights
WARNING! Read and understand all instructions.
Failure to follow all instructions listed below may
result in electric shock, fire and/or serious personal injury.
WARNING: For your own safety, read the tool
instruction manual before using any accessory. Failure
to heed these warnings may result in personal injury and
serious damage to the tool and the accessory. When
servicing this tool, use only identical replace ment parts.
WARNING: To reduce the risk of eye injury,
ALWAYS use eye protection when operating the
miter saw.
The DWS7085 is for use only with DEWALT light/laser
attachment miter saws.
SAVE THESE INSTRUCTIONS
Tool service must be performed only by qualified
repair personnel. Service or maintenance performed by
unqualified personnel may result in injury. To locate your
nearest D
EWALT service center call 1-800-4-DEWALT (1-800-
433-9258) or go to http://www.dewalt.com on the Internet.
Do not place the worklight in a position which may cause
anyone to intentionally or unintentionally stare into the
worklight. Serious eye injury could result.
Do not disassemble the worklight or worklight power
supply. There are no user serviceable parts inside.
Do not modify the worklight in any way. Modifying the
worklight may result in risk of injury.
The worklight is intended for lighting the workpiece area
and is not a safety device.
Do not remove or deface warning labels.
Use Miter Saw Worklight System only with specifically
designated D
EWALT Miter Saws. Use of Miter Saw
Worklight System on non-designated tools may create a risk
of injury.
Use worklight part # 641437-00 only with worklight power
supply part # 654657-00. Use of worklight with another
power supply may create injury.
The label on your tool may include the following symbols.
V ...................volts mW .........milliwatts
II ...................Class II worklight
.......direct current
................alternating current Hz ...........hertz
W ..................watts
Installation of Miter Saw LED
Worklight System
WARNING: Read all instructions for the Installation of Worklight
Power Supply and the Installation of Worklight before proceeding
with the Installation of the Miter Saw Worklight System.
INSTALLATION OF THE WORKLIGHT POWER SUPPLY
(WPS)
WARNING: To reduce the risk of serious personal injury,
turn tool off and disconnect tool from power source before
making any adjustments or removing/installing attachments
or accessories.
WARNING: To reduce the risk of serious personal injury,
DO NOT operate saw without the cover or power supply in
place.
English
2
1. Remove the two screws from the miter saw handle with
the T20 wrench provided. Save the screws to install the
Worklight Power Supply (WPS) in Step 4. Retain the handle
cover for future use if WPS is removed.
2. Attach the connections to the WPS.
3. Arrange the wire connection
such that the wide portion of the
connector is placed against the
bottom of the miter saw handle
and fit the WPS to the handle.
4. Attach the WPS with the two
screws removed in Step 1.
INSTALLATION OF THE WORKLIGHT
WARNING: To reduce the risk of serious personal injury,
turn tool off and disconnect tool from power source before
making any adjustments or removing/installing attachments
or accessories.
WARNING: To reduce the risk of serious personal injury,
DO NOT operate saw without the cover or worklight in
place.
WARNING: To reduce the risk of serious personal injury,
DO NOT touch the sharp points on the blade with fingers or
hands when guard is open.
1. Remove the four screws (A) with the the T20 wrench
provided. Save the screws to install the worklight in Step 4.
Retain the cover for future use if worklight is removed.
NOTE: Manually open the guard (B) if needed to access and
remove the lower two screws (A).
A
(lower
screw)
B
A
(upper
screw)
B
2. Attach the connection from
lead wire to the worklight.
English
3
3. Tuck the wire connection into
the area in the worklight as
shown. Attach the worklight to
the saw.
4. Attach the worklight with the
four screws removed in Step 1.
Tighten screws securely.
WARNING: Do not operate
the miter saw if any of the screws
are missing, stripped out or not
seated.
5. Manually open and close the guard to ensure no binding
occurs. With the guard closed, move the saw arm through a
full stroke to also ensure no guard binding occurs.
WARNING: To reduce the risk of serious personal
injury, Do not operate the saw if guard binding occurs.
Use of Miter Saw Worklight System
WARNING: Read all instructions for the Installation of Worklight
Power Supply and the Installation of Worklight before using the
Miter Saw Worklight System.
C
NOTE: The miter saw must be
connected to a power source.
The Miter Saw Worklight System is
equipped with an ON/OFF switch (C).
The Miter Saw Worklight System is
independent of the miter saw’s trigger
switch.
MAINTENANCE
WARNING: To reduce the risk of serious personal injury,
turn tool off and disconnect tool from power source before
making any adjustments or removing/installing attachments
or accessories.
WARNING: To reduce the risk of serious personal injury,
DO NOT touch the sharp points on the blade with fingers or
hands while performing any maintenance.
For the best worklight performance, perform the following
maintenance regularly.
• Carefully clean sawdust and debris from worklight lens with a
cotton swab.
DO NOT use solvents of any kind, they may damage the
lens.
Dust build-up can block the worklight and prevent it from
accurately indicating the line of cut.
Follow miters saw’s instruction manual to remove and install
blade.
• With blade removed from saw, clean pitch and build-up from
blade. Pitch and debris can interfere with the worklight and
prevent it from accurately indicating the line of cut.
SPECIFICATIONS
Light Source Power LED
Worklight 3.3 V DC
Power Supply Input: 120–240 V AC; 50/60 Hz
Output: 3.3 V DC, 0.9 A
Operating Temperature 32°F to 104°F (0°C to 40°C)
Storage Temperature 0°F to 185°F (-40°C to 85°C)
Environmental Water Resistant
English
4
Repairs
To assure product SAFETY and RELIABILITY, repairs,
maintenance and adjustments (including brush inspection and
replacement) should be performed by a D
EWALT factory service
center, a D
EWALT authorized service center or other qualified
service personnel. Always use identical replacement parts.
Three Year Limited Warranty
DEWALT will repair, without charge, any defects due to faulty
materials or workmanship for three years from the date of
purchase. This warranty does not cover part failure due to normal
wear or tool abuse. For further detail of warranty coverage and
warranty repair information, visit www.dewalt.com or call 1-800-
4-D
EWALT (1-800-433-9258). This warranty does not apply to
accessories or damage caused where repairs have been made
or attempted by others. This warranty gives you specific legal
rights and you may have other rights which vary in certain states
or provinces.
In addition to the warranty, D
EWALT tools are covered by our:
1 YEAR FREE SERVICE
D
EWALT will maintain the tool and replace worn parts caused
by normal use, for free, any time during the first year after
purchase.
90 DAY MONEY BACK GUARANTEE
If you are not completely satisfied with the performance of your
D
EWALT Power Tool, Laser, or Nailer for any reason, you can
return it within 90 days from the date of purchase with a receipt
for a full refund – no questions asked.
LATIN AMERICA: This warranty does not apply to products sold
in Latin America. For products sold in Latin America, see country
specific warranty information contained either in the packaging,
call the local company or see website for warranty information.
FREE WARNING LABEL REPLACEMENT: If your warning
labels become illegible or are missing, call 1-800-4-D
EWALT for
a free replacement.
English
5
Troubleshooting Guide
The worklight does not light. Check all connections. Refer to Installation of
Power Supply and to Installation of
Worklight. If light is still not visible call
1-800-4-D
EWALT (1-800-433-9258).
Español
15
Guía de detección de problemas
La luz de trabajo no ilumina. Verifique todas las conexiones. Consulte las secciones
sobre instalación de la fuente de energía e instalación
de la luz de trabajo. Si aun así la luz no ilumina, llame al
1-800-4-D
EWALT (1-800-433-9258).
compra. De esta manera, se le reintegrará el importe total del
producto sin formularle pregunta alguna.
AMÉRICA LATINA: Esta garantía no se aplica a los productos
que se venden en América Latina. Para los productos que se
venden en América Latina, debe consultar la información de la
garantía específica del país que viene en el empaque, llamar
a la compañía local o visitar el sitio Web a fin de obtener esa
información.
REEMPLAZO GRATUITO DE LAS ETIQUETAS DE
ADVERTENCIA: si sus etiquetas de advertencia se tornan
ilegibles o faltan, llame al 1-800-4-D
EWALT para que se las
reemplacen gratuitamente.
DEWALT Industrial Tool Co., 701 East Joppa Road, Baltimore, MD 21286 (SEP07) Form No. 656498-00 DWS7085
Copyright © 2007 D
EWALT
The following are trademarks for one or more D
EWALT power tools: the yellow and black color scheme; the “D” shaped air intake grill; the
array of pyramids on the handgrip; the kit box configuration; and the array of lozenge-shaped humps on the surface of the tool.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20

DeWalt DWS7085 User manual

Type
User manual

The DeWalt DWS7085 Heavy-Duty Miter Saw LED Worklight System is designed for use with DEWALT miter saws. It features a 3.3 V DC LED light, providing bright and accurate illumination of the work area. The worklight is powered by a 120-240 V AC, 50/60 Hz power supply and has an operating temperature range of 32°F to 104°F (0°C to 40°C). It is water-resistant and has an ON/OFF switch for convenient control.

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI