D&B Qi Mounting instructions

Type
Mounting instructions
System components - Mounting sets - Assembly
Safety instructions
The Qi Mounting system must only be used in conjunction with the
d&b Qi-Series loudspeaker as described in this mounting
instructions.
Installation should only be carried out by fully trained personel.
There are certain rules for installation that must be complied with.
It is the responsibility of the person installing the assembly to ensure
that the structure being attached to is suitable for the intended use.
Secondary safeties must always be provided and used when flying
or fixing loudspeaker loads overhead.
Load safety information
The maximum permitted working load limit of the Qi Mounting
system is 240 kg/530 lb or up to 9 x Qi1 loudspeaker. The over
all vertical splay angle should not exceed 105° (Angle between
the axis of the top and bottom cabinet of the colomn).
System weights (rounded values)
Items key and tools required:
Wrench
SW#17
17
Hex key
5 mm
Component Weight in kg (lb)
Qi1/7/10 21(46)
Qi-SUB/QiCSA-SUB 37(81)/40(88)
Z5145 Ci, Qi Mounting frame
Z5170 Qi Mounting adapter (in pairs)
Z5171 Qi Mounting bracket (in pairs)
Z5172 Qi-SUB Mounting bracket (in pairs)
7 (15.4)
2 (4.4)
3 (6.6)
4.5 (9.9)
5
Z5145
Z5171
1
2
5
4
3
6
3
Z5172
Z5170
Z5145: 1 x Ci, Qi Mounting frame
Z5170: 2 x Qi Mounting adapter (for Z5145)
including:
4 x Allen/Hex stud M10x50, Tuflock (1)
2 x Qi Rubber pad (2)
12 x U-washer 10.5 (3)
8 x Self locking nut M10 (4)
8 x Cover for M10 nut (5)
4 x Hexhead bolt M10 x 30 (6)
Z5171: 2 x Qi Mounting bracket
including:
4 x Allen/Hex stud M10x50, Tuflock (1)
2 x Qi Rubber pad (2)
4 x U-washer 10.5 (3)
4 x Self locking nut M10 (4)
4 x Cover for M10 nut (5)
Z5172: 2 x Qi-SUB Mounting bracket
3
1
4
6
2
Note:
The Z5171/72 Mounting brackets
differing into Left and Right:
- Direction of view L/R: From loudspeaker rear side.
- Shown: Front view - right side
D2973.E.01 Qi Mounting system, Mounting instructions
d&b Qi Mounting system, Mounting instructions (2.1 EN) 1
including:
4 x Allen/Hex stud M10x50, Tuflock (1)
2 x Qi Rubber pad (2)
4 x U-washer 10.5 (3)
4 x Self locking nut M10 (4)
4 x Cover for M10 nut (5)
Z5171 Qi Mounting bracket/Z5172 Qi-SUB Mounting bracket - Angle ranges
Qi1 - Angle range even from 0° to 14°
Qi1 - Angle range odd from 1° to 11°
Qi7/10 - Angle range from14° to 35°
Qi-SUB Following angle 0° or -5°
-5°
14°
35°
14°
Qi7/10
Angles
35°
30°
25°
20°
14°
-5°
-3°
10°
12°
14°
11°
Qi1
Angles
11°
Z5171
Z5172
d&b Qi Mounting system, Mounting instructions (2.1 EN) 2
d&b audiotechnik GmbH, Eugen-Adolff-Str. 134, D-71522 Backnang, Germany, Phone +49-7191-9669-0, Fax +49-7191-95 00 00
D2973.E.02, 01/2013 © d&b audiotechnik GmbH
Note:
Z5170
Front
  • Page 1 1
  • Page 2 2

D&B Qi Mounting instructions

Type
Mounting instructions

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI