Please select the proper location for your TV,
the display will be adjusted for best results.
Use keys to highlight your choice and then press ENTER key.
Store mode is for the
retail display setup.
Home Mode is for saving
energy and reducing power
consumption, this setting
qualifies for ENERGY STAR.
Home
Store
STORE
STORE
Please connect all antennas* and signals to the jacks and terminals.
Make sure all of your equipment is switched on.
Use keys to highlight your choice and then press ENTER key.
*To avoid signal interference when searching for channels using
an Indoor Antenna, place the antenna at least 3 feet away from TV.
Signal search
Skip
Use keys to highlight your choice and then press ENTER key.
Finish Setup
Repeat
Analog Channels...16 Digital Channels...24
Video 1...Yes HDMI 1...Yes
Video 2...no HDMI 2...no
Video 3...no
If you are having problems, call us toll-free at 1-800-877-5032
The search was successfully completed!
Finalize the completed Setup process.
Use the on-screen menu to select your HDTV’s location.
Perform a Signal search.
Choose the correct Input source
Finalize the completed Setup process.
Use the on-screen menu to select your HDTV’s location.
Use the CURSOR keys to highlight the Signal Search option and
press the ENTER key.
Use the CURSOR keys to highlight the Finish Setup option and
press the ENTER key.
Perform a Signal search.
Use the CURSOR keys to highlight the Signal Search option and
press the ENTER key.
Use the CURSOR keys to highlight the Finish Setup option and
press the ENTER key.
You can now watch and enjoy TV programming on your HDTV!
You can now watch and enjoy TV programming on your HDTV!
Choose the correct Input source
NOTE: Selecting Home mode will qualify as an Energy Star rating.
Use the CURSOR keys to highlight the desired option and press
the ENTER key.
NOTE: Selecting Home mode will qualify as an Energy Star rating.
Use the CURSOR keys to highlight the desired option and press
the ENTER key.
Use the POWER key to turn on your HDTV.
Use the following codes to program your cable or satellite provider’s
remote control to work with your new HDTV.
Use the following codes to program your cable or satellite provider’s
remote control to work with your new HDTV.
Direct TV
Dish Network
Comcast
Cox
Verizon
ATT
10154, 960
(to activate INPUT feature)
590, 683, 589, 542, 652
10154
0154, 0088
0181, 0826, 0920
1045, 1062, 1095, 1380
Connect the AC cord to the HDTV and to power outlet.
Please allow the HDTV a few minutes to complete the process.
Please allow the HDTV a few minutes to complete the process.
Use the INPUT key on your remote control to select
from the available Input sources on your HDTV.
NOTE: If you receive Satellite or Cable service through a
set top box, tune to the correct input on your HDTV and
use the receiver and its remote for channel viewing.
Use the INPUT key on your remote control to select
from the available Input sources on your HDTV.
NOTE: If you receive Satellite or Cable service through a
set top box, tune to the correct input on your HDTV and
use the receiver and its remote for channel viewing.
Si necesita ayuda en ESPAÑOL, marque al 1-800-877-5032 y un asesor
estará dispuesto a ofrecerle ayuda con cualquiera de sus dudas.
Si necesita ayuda en ESPAÑOL, marque al 1-800-877-5032 y un asesor
estará dispuesto a ofrecerle ayuda con cualquiera de sus dudas.
HDMI, the HDMI Logo and High-Definition Multimedia Interface are trademarks or registered trademarks of HDMI Licensing LLC in the United States and other countries.
NOTE: If these do not work, refer
to your Cable or Satellite manual.
NOTE: If these do not work, refer
to your Cable or Satellite manual.