Bradley Lenox Lockers LENOXPEDESTAL Installation guide

Bradley
Brand
Bradley
Model
Lenox Lockers LENOXPEDESTAL
Type
Installation guide
P.O. Box 309, Menomonee Falls, WI USA 53052-0309
PHONE 1-800-BRADLEY FAX (262) 251-5817
http://www.bradleycorp.com
Installation
Lenox Lockers™
Pedestal Bench
Banc Piédestal
Banco del Pedestal
Table of Contents
Pre-Installation Information � � � � � � � � � � � � � � � � � � � � � � � � � � � � 2
Hardware List � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 2
Installation � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 3
Table des matières
Avant l’installation � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 4
Liste de quincaillerie � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 4
Installation � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 5
Contenido
Información previa a la instalación � � � � � � � � � � � � � � � � � � � � � � 6
Lista del tornillería � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 6
Instalación � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 7
LK-INSTR-003 Rev.
D; EN 12-13-001
© 2012 Bradley
Page 1 of 7 4/4/2012
3'–4' length (qty� [2] pedestals)
3 à 4 longueurs de pied (qté� [2] piédestals)
3 a 4 longitudes de pie (cant� [2] pedestales)
5'–7' length (qty� [3] pedestals)
5 à 7 longueurs de pied (qté� [3] piédestals)
5 a 7 longitudes de pie (cant� [3] pedestales)
8' length (qty� [4] pedestals)
8 longueurs de pied (qté� [4] piédestals)
8 longitudes de pie (cant� [4] pedestales)
2
Lenox Lockers™ Pedestal Bench Installation
4/4/2012 Bradley Corporation • LK-INSTR-003 Rev. D; EN 12-13-001
Pre-Installation Information
Tools Required
• Tape measure
• Power Drill
• 3/16" drill bit
• 1/4" masonry drill bit
• Phillips driver bit
Hardware (provided by Bradley)
IMPORTANT
Read this installation manual completely to ensure proper installation. When finished
with the installation, file this manual with the owner or maintenance department.
Compliance and conformity to local codes and ordinances is the responsibility of the
installer.
Separate parts from packaging and make sure all parts are accounted for before
discarding any packaging material. If any parts are missing, do not begin installation
until you obtain the missing parts.
Accuracy is important when drilling the flange holes.
Review your layout drawings and verify the number of pedestal benches and
components before beginning installation. Refer to your submittal layouts for proper
placement of the pedestal benches.
Product warranties may be found under ”Products” on our web site at www.
bradleycorp.com.
Installation
THIS
SIDE
UP
Packing List
•
•
•
•
.
STD. HANDLE - VENT
.
SEE BOM
LOCKER ASSEMBLY
LK187218-1HV
.
.
NTS
SAME
11/30/01
.
.
.
TAM
.
.010
.015
2˚
.015
APP.CHANGE .RDN/C.ONETAD DRAWN BY
DO NOT
MATERIAL SPEC.
DRAWING
SCALE
PART NO.
NAME
TOLERANCES-
+
3 PLACE
ANGLES
FRACTIONS
2 PLACE
-
+
-
+
-
+
-
SPECIFIED:
OTHERWISE
UNLESS
USED ON
REFERENCE
ACAD #
SCALE
DATE
FIRST
DATE
DATE
APPR'D
CH'K'D
FAST-LF017
1/4" x 2-1/4" lg. stud with nut and washer for securing
the pedestals to the floor
FAST-S357
#14 x 1-3/4" lg. screw for attaching the pedestals to
the bench
WARNING
Failure to comply with these instructions,
or failure to use the hardware provided,
may result in personal injury and/or
property damage.
WARNING
Install only on a level, secure floor surface. Do not attempt to mount on wall or
other vertical surface. Make sure all floors are clean and smooth. Remove loose
impediments, such as protruding nails, and other debris which could affect
installation. The bench will be as level as the floor it is secured to. Do not use
shims to level the pedestal bench.
3
Installation Lenox Lockers™ Pedestal Bench
Bradley Corporation • LK-INSTR-003 Rev. D; EN 12-13-001 4/4/2012
Installation
Pedestal to Bench
6"
(152mm)
C
L
A
B
Position each pedestal on the
underside of the bench.
Mark the hole locations and
remove the pedestals.
Using a 3/16" drill bit, drill 1/2"
deep starter holes in the bench.
Secure the pedestals with the
#14 x 1-3/4" screws provided.
C
D
Position flanges and mark hole
locations on the floor. Remove
the bench.
Using a 1/4" masonry drill bit, drill
starter holes in the floor 1-1/8" to
1-1/4" deep.
Insert a stud, thread side up, into each hole.
Place a washer and nut (flush) on top of the stud
and tap on the nut with a hammer until seated.
Tighten nut to secure bench(es).
Bench to Floor
WARNING
Install only on a level, secure floor
surface. Do not attempt to mount
on wall or other vertical surface.
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7

Bradley Lenox Lockers LENOXPEDESTAL Installation guide

Bradley
Brand
Bradley
Model
Lenox Lockers LENOXPEDESTAL
Type
Installation guide
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

in other languages

Related papers

Other documents