CAME Australia Pty Limited
Automatic Gates – Access Control – Parking Equipment - Bollards
CAME Australia Pty Limited ABN 31 116 251 024
Unit 55, 11-21 Underwood Road, Homebush NSW 2140
T: (02) 9746 9991 F: (02) 9746 8891 W: www.came.com.au
SDN Slide Gate Programming
Before powering up the motor, remove the control board dust cover and insert the AF43S receiver card.
To energize the display press Enter, to scroll use the < (left) or > (right) arrows. The display initiates at the
F1 command. Factory setting for Safety Functions is set as disabled.
Disengage the motor, position the gate halfway and re-engage the motor.
Select A1 & press Enter. From the Motor Size submenu select 1 for 400Kg, 2 for 600Kg, 3 for 800Kg or 4
for 1000Kg. Press Enter.
Factory Default setting is for a Left hand install, to change to Right hand, press Enter and scroll to F54, from
the submenu change from 0 to 1 and press Enter
Select A3 & press Enter. This will begin the Setup Calibration. Select 1 & press Enter. The gate will first
close and then reopen slowly; this will set up the limits and slow down positions automatically.
Adding Radio Transmitters
1. To enter the remote transmitters, < scroll to U1 and press Enter
2. Select a command for the user‟s remote. 1 = step – step (open – close) 2 = sequential (open – stop –
close- stop) 3 = open only, 4 = partial opening. Press Enter to confirm
3. The next available user slot (between 1 & 25) will start to flash. Press and release the remote button
to be programmed.
4. Press Esc to exit programming. You can clone this code from remote to remote. To add further users,
repeat the above steps, the next available user slot will be selected automatically, or you can choose
the slot number manually.
Adding P.E. Beams
To activate P.E. Beams, scroll to F2 (CX) & press Enter. Select the photocell operation, C1 = reopening
during closing, C2 = close when opening, C3 = partial stop, C4 = obstacle wait
Loop setup
For an opening loop, power from 10 & 11 (24V) and connect to 2 & 3P (open only, requires Auto Close)
For a safety loop, connect to 2 and either F2 (CX) or F3 (CY) whichever is available. Select functions as per
P.E. Beams
Auto Close
Scroll to F19 & press Enter. Select a value between 1 and 180 seconds
RIO
Insert the RIOCONN card with the power off. Power up and the RIOCONN‟s LED‟s flash BLUE.
Insert the battery into the accessory (do not put both batteries in at the same time, each unit is powered and
programmed individually), the LED‟s will flash RED. Press the PROG button on the RIOCONN for 2
seconds the LED‟s stay on. The accessory LED‟s will flash BLUE, press and hold the T1 button for 2
seconds. Programming is complete when the LED‟s turn off. Repeat this process for any additional
accessory. An E17 error may occur, turn the power to the motor off and then on again, there should be
nothing on the LED screen. If the RIOCEL is not aligned the CEL will beep and a “P1” error shows.
CAME Australia Pty Limited
Automatic Gates – Access Control – Parking Equipment - Bollards
CAME Australia Pty Limited ABN 31 116 251 024
Unit 55, 11-21 Underwood Road, Homebush NSW 2140
T: (02) 9746 9991 F: (02) 9746 8891 W: www.came.com.au
BX 243 and BX 246 Commissioning
Factory default is a LHS installation with WHITE cam as OPEN and RED cam as CLOSED
1. Insert the AF43s card, attach the power lead to the L & N terminals and turn power on
2. Set Dipswitch 1 to OFF and Dipswitches 8, 9 & 10 to ON
3. Open the motor cover,
4. Disengage the clutch by pulling the lever out,
5. Close the gate fully and set the RED cam to the CLOSED position (always close onto the body of the
micro switch not to the spring)
6. Open the gate fully and set the WHITE cam to the OPEN position
7. Set all the pots to 50% except for gate run speed which is 100%
8. Press the red button and program in the first remote.
9. Re-engage the clutch, press remote and let it set up.
For BX 246
Follow steps 1 and 2 from the BX 243 setup
3. Open front door
4. Disengage the clutch by turning anticlockwise
5. Set limits on rack, re-engage clutch, close the door and lock securely
6. Run 2 complete cycles
7. Turn on dipsw 6
8. Press and hold Ch1 till the light goes solid
9. Turn off dipsw 6.
10. Ensure the front door is shut and locked at all times
To change from LH to RH install Swap FA and FC plus M + N wires
CAME Australia Pty Limited
Automatic Gates – Access Control – Parking Equipment - Bollards
CAME Australia Pty Limited ABN 31 116 251 024
Unit 55, 11-21 Underwood Road, Homebush NSW 2140
T: (02) 9746 9991 F: (02) 9746 8891 W: www.came.com.au
WIRING
10 + 11 24vAC for powering accessories MAX 37W or 1.6A
10 +E1 Flashing Light
1 + 2 Emergency Stop Bypass with dipsw 8
2 + 3P Partial Opening
10 + 5 Open gate status light bulb must be less than 3W
2 + 7 Open/Close dipsw 2 +3 off
Open stop/close stop dipsw 2 on
Open only dipsw 3 on
Open only dipsw 2 + 3 on
SAFETY
Anything with a “C” is for safety
C1 Reopening dipsw 9
C3 Partial Stop dipsw 10
C7 Safety Edge
C8 Safety Edge
TS Test photo cells (not used in Aus.)
Ground use RG59 cable
Aerial centre core
FA Opening Stop
FC Closing Stop
F Common
+ E Encoder for slow down
M + N power for 24vDC motor
FAULT FINDING
Check fuses and wires
Check power lights if no power light showing, check motor fuse
10 + 11 check for voltage of 24v
2 +7 check for voltage of 4.5vDC
Sensitivity increase to reduce power, decrease to increase power
CAME Australia Pty Limited
Automatic Gates – Access Control – Parking Equipment - Bollards
CAME Australia Pty Limited ABN 31 116 251 024
Unit 55, 11-21 Underwood Road, Homebush NSW 2140
T: (02) 9746 9991 F: (02) 9746 8891 W: www.came.com.au
Wiring of DIR10 and Delta SE*
C.B 10 2 C1
Rx 10 2 C NC Tx
Tx 2 Tx
*Reminder: Turn off dipswitch on Control Board
Wiring of DOC-E and DELTA E*
C.B 10 11 2 C1
Rx + - 2 NC
Tx + -
AMICO
1. Insert all wires between motors and CB, unlock motor using trilobed key
2. Set limits on operators, lock motor using trilobed key
3. Insert AF43S card
4. Connect power lead to L and N terminals, turn power on
5. Turn on dipsw 9 & 10 (on the 10 dipsw assembly) and turn on dipsw 1 (on the 2 dipsw assembly) *
6. Select Ch1, then press desired button on transmitter
7. Press Open Motor button, if polarity is right then the gate will open, if not swap M + N
8. Open gate leaves to 45 degrees using Open Motor button
9. Press setup, each gate leaf will cycle and set themselves
*For Amico set dipsw 7 ON, for Frog J set dipsw 7 OFF
CAME Australia Pty Limited
Automatic Gates – Access Control – Parking Equipment - Bollards
CAME Australia Pty Limited ABN 31 116 251 024
Unit 55, 11-21 Underwood Road, Homebush NSW 2140
T: (02) 9746 9991 F: (02) 9746 8891 W: www.came.com.au
ZLJ14 & 24
1. Insert all wires between motors and CB, Set limits on operators, Insert AF43S card
2. Connect lead to L and N, turn power on
3. To enter the MENU, press and hold <ENTER> for at least ONE SECOND
4. Scroll to LANGUAGE <ENTER> select ENGLISH <ENTER> ESC, ESC
5. Scroll to FUNCTIONS <ENTER>
6. Scroll to AUTOCLOSE <ENTER> select DISABLED <ENTER>
7. Scroll to TOTAL STOP <ENTER> select DISABLED <ENTER>
8. Scroll to CX <ENTER> select DISABLED <ENTER>
9. Scroll to CY <ENTER> select DISABLED <ENTER> (CZ disabled ex-factory) ESC, ESC
10. Scroll to IMP.RUN <ENTER> MOTOR TYPE <ENTER> set your motor <ENTER> ESC, ESC
11. Scroll to ENCODER <ENTER>
12. Scroll to SENSIB. RUN <ENTER> select half the dots <ENTER>
13. Scroll to SENSIB.DECEL<ENTER> select half the dots<ENTER>
14. Scroll to SET ENCODER <ENTER> select CONFIRM YES <ENTER> ESC, ESC
TO ADD USERS
15. Scroll to USER <ENTER>
16. Scroll to ADD USER <ENTER> scroll to ADD USER CONFIRM YES <ENTER> scroll to
RELATED FUNCTIONS <ENTER>
17. You can now press the Tx button
18. Repeat to add further users. Clone to add further remotes to each User slot.
ESC, ESC brings you back to the home screen of www.came.it (wait for 30 seconds to go out of
programming mode)
You can change the home screen by going to INFO <ENTER> scroll to STANDBY MSG. <ENTER>
insert new msg. <ENTER> hold for at least ONE SECOND
CAME Australia Pty Limited
Automatic Gates – Access Control – Parking Equipment - Bollards
CAME Australia Pty Limited ABN 31 116 251 024
Unit 55, 11-21 Underwood Road, Homebush NSW 2140
T: (02) 9746 9991 F: (02) 9746 8891 W: www.came.com.au
ZL92 Cheat Sheet
BASIC PROGRAMMING
Connect 4 wires for a Stylo, or 3 wires for an Amico.
Insert the AF43S receiver card.
Connect power to L + N
Set the endstops and lock the gate at 45°
To enter the programming mode, press and hold <ENTER> for at least one second, thereafter
Press „>‟ to scroll through to the following functions and press <ENTER> to select
A1 Motor selection, select 1 for Stylo with joint arm, 2 for Stylo with straight arm, 3 for Myto, 4 for Frog J,
5 for Amico.
F1 Total Stop, change the value to „0‟
F2 CX, change to „0‟ if no safety beams are installed
F3 CY, change to „0‟ if no safety beams are installed
F46 Number of Motors, select „0‟ for 2 motors or „1‟ for single motor on M2
A2 Motor Test, change to „1‟ then press and hold „>‟ which will activate the M2 motor. Next, press and hold
the „<‟ for the M1 motor. The gates should OPEN; if they are closing you will need to swap the M+N
connectors.
A3 Calibration, change the value to „1‟ and the gates will automatically run and calibrate for all settings
during the opening and closing cycles.
ADDING DEVICES TO THE BOARD
U1 Remotes Add Users, change to „1‟ and the slot number will flash, press the remote button and the
number will go solid to signify successful programming of that slot.
Repeat this procedure for up to 25 User slots. Additional remotes can be cloned to each User slot.
F2 Safety Beams on CX, change to „1‟ for reopening during closing
F19 Auto Closing, change the values in the time range from 1 to 180 seconds. Ensure that the opening
device is connected to 2 + 3 (open only)
NOTE: to exclude the ENCODER FUNCTIONS if there are any PROBLEMS go to F11 and change the
value to „1‟.
CAME Australia Pty Limited
Automatic Gates – Access Control – Parking Equipment - Bollards
CAME Australia Pty Limited ABN 31 116 251 024
Unit 55, 11-21 Underwood Road, Homebush NSW 2140
T: (02) 9746 9991 F: (02) 9746 8891 W: www.came.com.au
ZBK-10 Cheat Sheet
Set limits on rack, Insert the AF43S card and lock the gate half way open
Connect lead to L and N, turn power on
To enter the MENU, press and hold <ENTER> for at least ONE SECOND then scroll to:
LANGUAGE <ENTER> select ENGLISH <ENTER>
AUTOCLOSE <ENTER> select OFF <ENTER>
STOP(1) <ENTER> select OFF <ENTER>
CX <ENTER> select DISABLED <ENTER>
CY <ENTER> select DISABLED <ENTER> (CZ OFF ex-factory)
RADIO USERS <ENTER> scroll to NEW USER <ENTER> scroll to RELATED FUNCTIONS
<ENTER>
You can now press the remote button
Repeat to add further users. Additional remotes can be cloned to each User slot.
ADJUSTMENTS <ENTER> select GATE RUN ADJ <ENTER> the gate will OPEN and then
CLOSE. If reversed, swap U + V plus FA + FC connections
TO ADD
P.E. Beams: Scroll to CX <ENTER> select C1 <ENTER> (reopen on closing)
Loops: connect the contacts to 2 + 3 then Scroll to FUNCTIONS <ENTER> AUTOCLOSE
<ENTER> select ON <ENTER>
To adjust the auto closing time scroll to TIMING ADJ <ENTER> and change the value from 0” to
120”
CAME Australia Pty Limited
Automatic Gates – Access Control – Parking Equipment - Bollards
CAME Australia Pty Limited ABN 31 116 251 024
Unit 55, 11-21 Underwood Road, Homebush NSW 2140
T: (02) 9746 9991 F: (02) 9746 8891 W: www.came.com.au
QUICK CONTROL BOARD SETUP
BASIC SETUP. ADD P.E. ADD LOOP
ZBX6 1+2 2+C1 Bridged REMOVE 2+C1 NOT AVAILABLE
ZBX74 7, 8 & 9 ON 7 OFF 2+7, DIP 3 ON
ZBK/E 7, 8, 10 ON (Block 1) 7 OFF 2+3
ZD2 8, 9 & 10 ON 9 OFF 2+7 DIP 3 ON
ZN2 8, 9 & 10 ON 9 OFF NOT AVAILABLE
ZL90 9 & 10 (Block 1) 1 (Block 2) 10 OFF 2+7, DIP 3 ON
ZL92 MENU MENU SETTINGS 2+7
ZL180 7 & 8 ON 1+2 Bridged 7 OFF 2+7, DIP 3 ON
ZLJ 14/24 MENU MENU SETTINGS 2+7
ZN7 A1motor, A3 configure F2 2+3P
--------------------------------------------------------------------------------------------------------------------------------
DUPLICATING THE TRANSMITTER (CLONING)
Your first transmitter sends a code to the receiver, after that you need to clone from a programmed
transmitter to a new transmitter.
1 – On the new transmitter, press and hold both buttons together until the LED flashes quickly (about 5 secs)
2 – Now press the button you wish to activate (the LED stays on)
3 – Within 10 seconds, place the active transmitter to the key ring position of the new transmitter and
press the programmed button. The LED will flash 3 times to indicate memorisation
CAME Australia Pty Limited
Automatic Gates – Access Control – Parking Equipment - Bollards
CAME Australia Pty Limited ABN 31 116 251 024
Unit 55, 11-21 Underwood Road, Homebush NSW 2140
T: (02) 9746 9991 F: (02) 9746 8891 W: www.came.com.au
BOOM GATE SETUP G4040 & G2080
Boom gates should be assembled so that if the arm is hit it moves away from the motor casing
After assembling the barrier balance the arm at 45°
Turn on Dips 8, 9 & 10 (Brake) and bridge 2 + C1 (this is the basic setup)
Lock the barrier arm using the back panel key switch; the front panel also needs to be locked to engage the
motor safety microswitch
Bridge 2 + 3, if the barrier opens, the motor has been set correctly for a Left Hand installation. If the arm
goes down, the motor polarity is reversed and the M (Brown) & N (Blue) terminals need to be swapped.
Also swap the limit switch terminals FA (White) & FC (Red).
AUTOMATING THE BARRIER
CAME Remotes
Turn off the power. Insert the AF43S card, turn the power back on.
Keep the PROG button pressed on the control board, the LED will flash. Press the transmitter button to be
memorized, the LED will stay solid to signal memorization. Clone from a working remote to a non-
programmed remote
LOOP
For Free to Exit, connect to 2 + 3 to open the gate. Power from 10 + 11
For tailgating connect to 2 + C5 (immediate closure)
P.E. Beam
Remove bridge from 2 + C1
Insert Common to 2 and NC to C1, 24V power from 10 + 11
Ensure Dip 7 is OFF (Master/Slave)
AUTO CLOSE
Turn on Dip 1 and set the A.C.T. for required time (clockwise to add time)
ACCESS CONTROL
2 + 3 for Opening, turn on Dipswitch 1 and set closing time on the A.C.T. trimmer.
CAME Australia Pty Limited
Automatic Gates – Access Control – Parking Equipment - Bollards
CAME Australia Pty Limited ABN 31 116 251 024
Unit 55, 11-21 Underwood Road, Homebush NSW 2140
T: (02) 9746 9991 F: (02) 9746 8891 W: www.came.com.au
AMICO INWARD OPENING
AMICO OUTWARD OPENING
CAME Australia Pty Limited
Automatic Gates – Access Control – Parking Equipment - Bollards
CAME Australia Pty Limited ABN 31 116 251 024
Unit 55, 11-21 Underwood Road, Homebush NSW 2140
T: (02) 9746 9991 F: (02) 9746 8891 W: www.came.com.au
AXO INWARD OPENING
AXO OUTWARD OPENING
/
