Terex Genie AWP Series Installation Instructions Manual

Rev 2

FAILURE TO COMPLETE THIS BULLETIN MAY

RESULT IN DEATH OR SERIOUS INJURY.

1 of 5

CAMPAIGN BULLETIN 090007

Original Release Date: October 29, 2009

Revised Date: 25-01-2010

Subject: Platforms with Gated Entry

Models and Serial Numbers Affected:

GR : GR-101 to GR09-14664

AWP: 3896-101 to 3801-21190

AWP02-21198 to AWP09-65432

IWP : 4096-101 to 4001-4199

IWP02-4218 to IWP09-8283

CWP : 0001-109

0196-118 to 0101-1248

CWP02-1249

SP : 1796-101 to 1797-255

Allowable Hours: 30 minutes

Issue:

Genie Industries, Inc. has received reports that the gate in the above referenced machines can

fail to latch. If the gate does not latch, the guard rail system does not provide the required

level of fall protection for the operator.

Rev 2

FAILURE TO COMPLETE THIS BULLETIN MAY

RESULT IN DEATH OR SERIOUS INJURY.

2 of 5

CAMPAIGN BULLETIN 090007

Action Required:

1. Immediately locate all machines within the serial number ranges shown above.

2. Until the new kit is installed, ensure that the gate is latching as shown in the pictures

below. If the gate does not latch as shown in the pictures below, immediately remove

the machine from service.

Gate is properly latched when the pin is engaged in the slot

underneath the gate swing arm

slot

p

in

gate

swing

arm

Rev 2

FAILURE TO COMPLETE THIS BULLETIN MAY

RESULT IN DEATH OR SERIOUS INJURY.

3 of 5

CAMPAIGN BULLETIN 090007

floor length floor width

double side

entry

3. Use the illustrations below, and determine the type of platform on your machine.

Type A Type B

(Platform with Extension) (Utility Platform)

Type C

(Standard, Extra Large, Narrow

and Ultra Narrow)

4. If your machine is equipped with type A or B platform, continue on to step 5.

If your machine is equipped with type C platform, measure the floor length and floor

width of the platform.

Note: Use the attached Parts Order Form to record the dimensions of your platform.

Rev 2

FAILURE TO COMPLETE THIS BULLETIN MAY

RESULT IN DEATH OR SERIOUS INJURY.

4 of 5

CAMPAIGN BULLETIN 090007

5. Use the table below to determine the kit for your platform:

Platform Style

Floor Dimension

(L x W)

Kit

P/N

Type A Platform (GR models from GR-101 to GR01-341) N/A 145325

Type A Platform (GR models from GR01-342 to GR05-5000) N/A 145187

Type A Platform (GR models from GR05-5001 to GR06-7389) N/A 145321

Type A Platform (GR models from GR06-7390 to GR09-14664) N/A 145186

Type B Platform (Utility Platform: SP or CWP) N/A 145277

Type C Platform (Standard : AWP, IWP , CWP or GR) 26 in x 27 in (66 cm x 68 cm) 145183

Type C Platform (Extra Large : AWP, IWP or CWP) 30 in x 27 in (76 cm x 68 cm) 145183

Type C Platform (Narrow: AWP,IWP or CWP) 26 in x 20 in (66 cm x 51 cm) 145184

Type C Platform (Narrow: GR model) 26 in x 20 in (66 cm x 51 cm) 145270

Type C Platform (Ultra Narrow: AWP,IWP, CWP or GR) 22 in x 18 in (56 cm x 48 cm) 145185

6. Completely fill out the attached Parts Order Form and fax to Genie’s Parts Department

to receive, at no charge, a gate latch kit with installation instructions.

Upon receipt of parts, installation must take place as soon as possible, but no later

than 30 days from receipt of parts.

7. Fill out and sign the completion form included with the instructions in the parts kit and fax

to Genie’s warranty department to verify that this campaign bulletin has been completed.

Rev 2

FAILURE TO COMPLETE THIS BULLETIN MAY

RESULT IN DEATH OR SERIOUS INJURY.

5 of 5

CAMPAIGN BULLETIN 090007

Warranty:

The labor and travel distance required to perform this inspection and installation are covered

under the provisions of our warranty agreement. Warranty claims can be submitted by paper

claim or online. Please combine as many machines as possible on one claim form. If you need

more information about filing a warranty claim, call Genie’s warranty department.

If you are the owner of an affected machine and are not an authorized Genie dealer,

please contact your nearest Genie dealer for assistance in completing this bulletin. Only

Genie Authorized Dealers will be reimbursed for labor or any other costs associated with

this bulletin under the provisions of our standard warranty terms and conditions.

Local norms and regulations requires that the seller of a Genie machine report to Genie the

model and serial number of each machine sold, as well as the name, address, and telephone

number of the new owner, within 60 days of the sale.

Regulations also require that the manufacturer’s campaign bulletins be completed. It is your

responsibility to communicate this important information to all machine owners and applicable

branches. If you require additional copies of this bulletin or have any questions, please contact

Genie’s service department at:

UK: 00 44 1476 584 333

France: 00 33 237 260 986

Germany: 00 49 422 1491821

Italy: 0039 075 941 8171

Iberica: 0034 935 725 380

Scandinavia: 0046 3157 5154

Middle East: 0097 143 391 800 or

0097 150 459 7937

All other locations: 0031 653 221 908

Enclosures:

Parts order form

Owner update form

Machine list report

Rev 2

CAMPAIGN BULLETIN 090007

Owner Update Form

(for updating machine owner information only)

Genie requires that the seller of a Genie machine report to Genie the model and serial number of each

machine sold, as well as the name, address, and telephone number of the new owner, within 60 days of the

sale.

• If you have sold a machine, list the complete model and serial number (example: GR05-5062, AWP06-

52934, IWP08-7698, 0198-627 and 1797-183)

and the name, address and phone number of the new owner.

New Owner Information:

Machine 1

Machine 2

Machine 3

Model*

Serial Number*

Owner Name*

Address 1*

Address 2

City/State/Zip*

Phone Number*

Contact Person

* Required fields.

Seller Information:

Date:

Company Name:

Account #:

Address:

(street)

(city)

State, zip code

Phone #:

• List any machines that could not be inspected or repaired because of the following:

Model & Serial Number Scrapped Exported Stolen Others (explain)

- - - -

Fax to:

UK: 0044 1476 584 330 Italy : 0039 075 941 8146

France: 0033 237 310 300 Scandinavia: 0046 3157 5104

Germany: 0049 422 149 1820 Middle East: 0097 143 391 802

Iberica: 0034 935 725 080 All other locations: 0031 183 581 566

Rev 2

CAMPAIGN BULLETIN 090007

Parts Order Form

Fax this form to Genie Industries to receive the indicated Gate Latch Kit for your machine. List the model and

serial number of each affected machine.

• Please list the complete model and serial number (example: GR05-5062, AWP06-52934,

IWP08-7698, 0198-627 and 1797-183)

Platform Style

Floor Dimension

(L x W)

Kit P/N

Type A Platform (GR models from GR-101 to GR01-341) N/A 145325

Type A Platform (GR models from GR01-342 to GR05-5000) N/A 145187

Type A Platform (GR models from GR05-5001 to GR06-7389) N/A 145321

Type A Platform (GR models from GR06-7390 to GR09-14664) N/A 145186

Type B Platform (Utility Platform: SP or CWP) N/A 145277

Type C Platform (Standard : AWP, IWP , CWP or GR) 26 in x 27 in (66 cm x 68 cm) 145183

Type C Platform (Extra Large : AWP, IWP or CWP) 30 in x 27 in (76 cm x 68 cm) 145183

Type C Platform (Narrow: AWP,IWP or CWP) 26 in x 20 in (66 cm x 51 cm) 145184

Type C Platform (Narrow: GR model) 26 in x 20 in (66 cm x 51 cm) 145270

Type C Platform (Ultra Narrow: AWP,IWP, CWP or GR) 22 in x 18 in (56 cm x 48 cm) 145185

Serial Number Platform Type Floor Dimension (L x W) Kit P/N

- - -

Send Parts to: (If you would like to send

parts to a different location)

Date:

Company Name Company Name:

Ordered By: Attn:

Account No.: Account No.:

Address: Address:

(street) (street)

(city) (city)

(state, zip code) (state, zip code)

Fax to Holland: 00 31 165 511 148

Parts Manual

Serial Number Range

Installation Instructions

Part No. 145159

Rev B

Gated Entry

AWP

IWP

GR

CWP

SP

REV B

2 AWP • IWP • CWP • SP • GR Part No. 145159

Installation Instructions

Information

Observe and Obey:

Repair procedures shall be completed by a

person trained and qualified on the repair of this

machine.

Immediately tag and remove from service a

damaged or malfunctioning machine.

Before Starting Installation:

Read, understand and obey the safety rules

and operating instructions in the appropriate

Operator's Manual.

Be sure that all necessary tools and parts are

available and ready for use.

Read this procedure completely and adhere to

the instructions. Attempting shortcuts may

produce hazardous conditions.

Important:

This procedure is for the replacement of the

gated entry mid-rail on certain AWP, IWP, CWP,

SP and GR machines, as required by Campaign

Bulletin 090007.

Tools required:

7

/16 inch combination wrench

7

/16 inch socket

3

/8 inch drive ratchet

Screwdriver

Gated Entry

REV B

Installation Instructions

Part No. 145159 AWP • IWP • CWP • SP • GR 3

Use the chart below to determine the appropriate kit to be used on your platform.

Components of Kit 145183

Installation Instructions

Genie part number 145159

Qty. 1

Gated Tube Assembly, AWP

Genie part number 145190

Qty. 1

Bushing,

3

/8 OD x

1

/4 ID x 1.5 inches

Genie part number 37719

Qty. 2

Shim, 0.375 x 0.063 inch

Genie part number 12013

Qty. 4

Screw - HHC,

1

/4 -20 x 2.25 inches

Genie part number 8179

Qty. 2

LP Nylock Nut,

1

/4 -20

Genie part number 6889

Qty. 2

Components of Kit 145184

Installation Instructions

Genie part number 145159

Qty. 1

Gated Tube Assembly, AWP Narrow

Genie part number 145191

Qty. 1

Bushing,

3

/8 OD x

1

/4 ID x 1.5 inches

Genie part number 37719

Qty. 2

Shim, 0.375 x 0.063 inch

Genie part number 12013

Qty. 4

Screw - HHC,

1

/4 -20 x 2.25 inches

Genie part number 8179

Qty. 2

LP Nylock Nut,

1

/4 -20

Genie part number 6889

Qty. 2

Platform Style Floor Dimension Kit P/N

(L x W)

Platform with extension

(GR models from GR01-101 to GR01-341)

N/A 145325

Platform with extension

(GR models from GR01-342 to GR 05-5000)

N/A 145187

Platform with extension, LH

(GR models from GR 05-5001 to GR 06-7389)

N/A 145321

Platform with extension

(GR models from GR 06-7390 to GR 09-14664)

N/A 145186

Utility Platform (Stock Picker or CWP) N/A 145277

Standard Platform (AWP, IWP, CWP or GR) 26 in x 27 in (66 cm x68 cm) 145183

Extra Large Platform (AWP, IWP or CWP) 30 in x 27 in (76 cm x68 cm) 145183

Narrow Platform (AWP, IWP or CWP) 26 in x 20 in (66 cm x 51 cm) 145184

Narrow Platform (GR model) 26 in x 20 in (66 cm x 51 cm) 145270

Ultra Narrow Platform (AWP, IWP or CWP) 22 in x 18 in (56 cm x48 cm) 145185

REV B

4 AWP • IWP • CWP • SP • GR Part No. 145159

Installation Instructions

Components of Kit 145185

Installation Instructions

Genie part number 145159

Qty. 1

Gated Tube Assembly, AWP Ultra Narrow

Genie part number 145192

Qty. 1

Bushing,

3

/8 OD x

1

/4 ID x 1.5 inches

Genie part number 37719

Qty. 2

Shim, 0.375 x 0.063 inch

Genie part number 12013

Qty. 4

Screw - HHC,

1

/4 -20 x 2.25 inches

Genie part number 8179

Qty. 2

LP Nylock Nut,

1

/4 -20

Genie part number 6889

Qty. 2

Components of Kit 145186

Installation Instructions

Genie part number 145159

Qty. 1

Gated Tube Assembly, GR

Genie part number 145193

Qty. 1

Bushing,

3

/8 OD x

1

/4 ID x 1.5 inches

Genie part number 37719

Qty. 2

Shim, 0.375 x 0.063 inch

Genie part number 12013

Qty. 4

Screw - HHC,

1

/4 -20 x 2.25 inches

Genie part number 8179

Qty. 2

LP Nylock Nut,

1

/4 -20

Genie part number 6889

Qty. 2

Components of Kit 145187

Installation Instructions

Genie part number 145159

Qty. 1

Gated Tube Assembly, GR GEN 1

Genie part number 145194

Qty. 1

Bushing,

3

/8 OD x

1

/4 ID x 1.5 inches

Genie part number 37719

Qty. 2

Shim, 0.375 x 0.063 inch

Genie part number 12013

Qty. 4

Screw - HHC,

1

/4 -20 x 2.25 inches

Genie part number 8179

Qty. 2

LP Nylock Nut,

1

/4 -20

Genie part number 6889

Qty. 2

Components of Kit 145270

Installation Instructions

Genie part number 145159

Qty. 1

Gated Tube Assembly, AWP Narrow Platform GR

Genie part number 145269

Qty. 1

Bushing,

3

/8 OD x

1

/4 ID x 1.5 inches

Genie part number 37719

Qty. 2

Shim, 0.375 x 0.063 inch

Genie part number 12013

Qty. 4

Screw - HHC,

1

/4 -20 x 2.25 inches

Genie part number 8179

Qty. 2

LP Nylock Nut,

1

/4 -20

Genie part number 6889

Qty. 2

REV B

Installation Instructions

Part No. 145159 AWP • IWP • CWP • SP • GR 5

Components of Kit 145277

Installation Instructions

Genie part number 145159

Qty. 1

Gated Tube Assembly, CWP Utility Platform

Genie part number 145278

Qty. 1

Bushing,

3

/8 OD x

1

/4 ID x 1.5 inches

Genie part number 37719

Qty. 2

Shim, 0.375 x 0.063 inch

Genie part number 12013

Qty. 4

Screw - HHC,

1

/4 -20 x 2.25 inches

Genie part number 8179

Qty. 2

LP Nylock Nut,

1

/4 -20

Genie part number 6889

Qty. 2

Components of Kit 145321

Installation Instructions

Genie part number 145159

Qty. 1

Gated Tube Assembly, GR Gated LH

Genie part number 145320

Qty. 1

Bushing,

3

/8 OD x

1

/4 ID x 1.5 inches

Genie part number 37719

Qty. 2

Shim, 0.375 x 0.063 inch

Genie part number 12013

Qty. 4

Screw - HHC,

1

/4 -20 x 2.25 inches

Genie part number 8179

Qty. 2

LP Nylock Nut,

1

/4 -20

Genie part number 6889

Qty. 2

Components of Kit 145325

Installation Instructions

Genie part number 145159

Qty. 1

Gated Tube Assembly, GR GEN 1 LG

Genie part number 145326

Qty. 1

Bushing,

3

/8 OD x

1

/4 ID x 1.5 inches

Genie part number 37719

Qty. 2

Shim, 0.375 x 0.063 inch

Genie part number 12013

Qty. 4

Screw - HHC,

1

/4 -20 x 2.25 inches

Genie part number 8179

Qty. 2

LP Nylock Nut,

1

/4 -20

Genie part number 6889

Qty. 2

REV B

6 AWP • IWP • CWP • SP • GR Part No. 145159

Installation Instructions

Note: Perform this procedure on a firm, level

surface with the platform in the stowed position.

Remove Existing Mid Rail

1 Turn the key switch to the off position and push

in the red Emergency Stop button to the off

position at the ground controls.

2 Working at the gated entry of the platform,

locate the gas strut connected to the mid-rail

and vertical channel of the platform.

3 Using Illustration 1 as a guide and working at the

extension side of the gas strut, insert a flat

blade screwdriver between the indent of the

plastic ball socket and retaining clip. At the

same time, carefully move the retaining clip

away from the socket and remove the lower

half of the gas strut from the ball stud. Do not

remove the retaining clip from the plastic ball

socket.

Procedure

4 Working at the gated entry mid rail opposite the

entry knob, remove the fasteners securing the

mid-rail to the vertical channel of the platform.

Discard the fasteners. Refer to Illustration 2.

Gas Strut

Plastic Ball Socket

and Retaing Clip

Ball Stud

Illustration 1

Illustration 2

5 Working at the side of the gated entry mid-rail

with the entry knob, remove the fasteners

securing the mid-rail to the hinge plates.

Discard the mid-rail and fasteners. Refer to

Illustration 3.

Mid-Rail

Fasteners

Illustration 3

Entry Knob

Mid-Rail

Fasteners

Hinge Plates

Gas Strut

Ball Strut

Plastic Ball Socket

and Retaining Clip

Fasteners

Mid-Rail

Fasteners

Entry Knob

Hinge Plates

Fasteners

Mid-Rail

Fasteners

REV B

Installation Instructions

Part No. 145159 AWP • IWP • CWP • SP • GR 7

PROCEDURE

Install the Gated Tube Assembly

6 Using Illustration 4 as a guide and working with

the provided gated tube assembly (Genie part

number 145190, 145191, 145192, 145193,

145194, 145269, 145278, 145320 or 145326),

install the provided bushings and shims (Genie

part numbers 37719 and 12013) onto the gated

tube assembly.

Illustration 4

a gated tube assembly

b shim

c bushing

7 Working at the side of the gated entry

assembly with the entry knob and using the

provided fasteners (Genie part numbers 8179

and 6889), install the gated tube assembly onto

the hinge plates. Torque the fasteners to 100 in-

lbs / 11.3 Nm. Refer to Illustration 5.

Illustration 5

a gated entry assembly

b gated tube assembly

c ball stud

d plastic ball socket

e retaining clip

f platform rail vertical channel

g screw

h nylock nut

i hinge plate

8 Using the provided fasteners (Genie part

numbers 8179 and 6889), install the opposite

end of the gated tube assembly to the platform

rail vertical channel. Torque the fasteners to

100 in-lbs / 11.3 Nm. Refer to Illustration 5.

a b

c

b

c

b

ba

gh

i

c

g

h

de

f

REV B

8 AWP • IWP • CWP • SP • GR Part No. 145159

Installation Instructions

PROCEDURE

9 Using Illustration 5 as a guide and working at the

extension side of the gas strut, insert a flat

blade screwdriver between the indent of the

plastic ball socket and retaining clip. At the

same time, carefully move the retaining clip

away from the socket and install the lower half

of the gas strut onto the ball stud. Remove the

screwdriver from the retaining clip and plastic

ball socket, making sure the retaining clip fully

seats around the ball socket.

10 After the installation is complete, open and

close the entry gate to ensure it is working

properly.

Result: When the entry gate is opened and

closed, the gate slides inside the vertical

channel of the platform. Proceed to step 11.

Result: The entry gate is not opening and

closing properly. Contact the Genie Industries

Service Department at one of the telephone

numbers on this page.

Finish the Installation

11 Perform function tests. Refer to the operator's

manual on your machine.

12 Return the machine to service.

13 Upon completion of this installation, fill out and

sign the attached Completion Form and fax to

Genie Industries. This will serve as verification

that you have completed Campaign Bulletin

090007.

If you have any further questions regarding these

instructions or need assistance, please contact the

Genie Industries Service Department at one of the

following telephone numbers:

United States: 800-536-1800

Canada: 425-881-1800

Europe: UK 0044 1476 584 333

France 0033 237 260 986

Germany 0049 422 149 1821

Iberica 0034 935 725 380

Scandinavia 0046 3157 5154

other locations 0031 653 221 908

Middle East: 0097 143 391 800

or 0097 150 459 7937

Italiy 0039 075 941 8146

CAMPAIGN BULLETIN 090007

Completion Form

Your signature on this form will verify that you have installed the Gated Entry Kit specified for your

machine.

Fax to: UK 0044 1476 584 330

France 0033 237 310 300

Germany 0049 422 149 1820

Iberica 0034 935 725 080

Italy 0039 075 941 8146

Scandinavia 0046 3157 5104

Middle East 0097 143 391 802

All other locations 0031 183 581 566

Date:

Company Name:

Account # (if applicable)

Address:

(street)

(city)

(state, zip code)

Phone

Please list the complete serial number (example: AWP04- 27766, IWP04-5186 or GR04-4009)

Serial Number:

Signature (service manager)

CAMPAIGN BULLETIN 090007 Supplement

Date: 25-01-2010

Subject: Platforms with Gated Entry

Model and Serial Numbers Affected:

GR : GR-101 to GR09-14664

AWP: 3896-101 to 3801-21190

AWP02-21198 to AWP09-65432

IWP: 4096-101 to 4001-4199

IWP02-4218 to IWP09-8283

CWP: 0001-109

0196-118 to 0101-1248

CWP02-1249

SP : 1796-101 to 1797-255

This letter is a supplement to Campaign Bulletin 090007 released on October 29, 2009.

The serial number range of affected machines has not changed. However, the kit list has

been updated. Two more kits were added for GR models equipped with gated extension

platform (type A platform). The machines affected are units from serial number GR-101 to

GR01-341 and from GR05-5001 to GR06-7389. Enclosed is an updated version of the

bulletin and the Parts Order Form.

What you need to do:

For GR models equipped with type A platform from GR-101 to GR01-341:

• Refer to the attached Parts Order Form and order kit P/N 145325.

• If you already ordered P/N 145187, discard the kit upon receipt.

For GR models equipped with type A platform from GR05-5001 to GR06-7389:

• Refer to the attached Parts Order Form and order kit P/N 145321.

• If you already ordered P/N 145186, discard the kit upon receipt.

We share in your intense concern for the safety of our customers and sincerely appreciate

your efforts on our behalf. Please do not hesitate to contact the Genie Service Department if

you should have any questions regarding this important safety issue.

Rev 2

NICHTBEFOLGUNG DIESES BULLETINS KANN

SCHWERE VERLETZUNGEN ODER TOD ZUR FOLGE HABEN.

1 of 5

SICHERHEITSBULLETIN 090007

Ursprüngliche Ausgabe: 29. Oktober 2009

Revisionsdatum: 25-01-2010

Betreff: Arbeitsbühnen mit verriegelbarem Plattformeinstieg

Betroffene Modell- und Seriennummern:

GR : GR-101 bis GR09-14664

AWP: 3896-101 bis 3801-21190

AWP02-21198 bis AWP09-65432

IWP: 4096-101 bis 4001-4199

IWP02-4218 bis IWP09-8283

CWP: 0001-109

0196-118 bis 0101-1248

CWP02-1249

SP : 1796-101 bis 1797-255

Max. zulässige Arbeitszeit: 30 Minuten

Sachverhalt:

Genie Industries, Inc. hat Berichte erhalten, denen zufolge es vorkommen kann, dass die

Einstiegsverriegelung an den oben genannten Maschinen nicht einrastet. Wenn die

Einstiegsverriegelung nicht einrastet, bietet das Sicherheitsgeländer nicht die

erforderliche Sturzsicherung für die Bediener.

Rev 2

NICHTBEFOLGUNG DIESES BULLETINS KANN

SCHWERE VERLETZUNGEN ODER TOD ZUR FOLGE HABEN.

2 of 5

SICHERHEITSBULLETIN 090007

Erforderliche Maßnahmen:

1. Ermitteln Sie umgehend die Betriebsorte aller Maschinen mit den oben angegebenen

Seriennummern.

2. Stellen Sie bis zur Installation des Nachrüstsatzes sicher, dass die Einstiegsverriegelung

wie unten dargestellt einrastet. Nehmen Sie Maschinen, bei denen die

Einstiegsverriegelung nicht wie unten dargestellt einrastet, sofort außer Betrieb.

Die Einstiegsverriegelung ist ordnungsgemäß verriegelt, wenn der

Stift in der Aussparung unten an der hochschwenkbaren

Einstiegsverriegelung einrastet.

Aussparung

Stift

Hoch-

schwenkbare

Einstiegsver-

riegelung

Rev 2

NICHTBEFOLGUNG DIESES BULLETINS KANN

SCHWERE VERLETZUNGEN ODER TOD ZUR FOLGE HABEN.

3 of 5

SICHERHEITSBULLETIN 090007

Bodenlänge Bodenbreite

Beidseitiger

Einstieg

3. Ermitteln Sie anhand der folgenden Abbildungen den Plattformtyp an Ihrer Maschine.

Typ A Typ B

(Plattform mit Ausschub) (Utility-Plattform)

Typ C

(Standard, extragroß, schmal, und

superschmal)

4. Ist Ihre Maschine mit Plattformtyp A oder B ausgestattet, fahren Sie mit Punkt 5 fort.

Ist Ihre Maschine mit Plattformtyp C ausgestattet, messen Sie die Länge und Breite des

Plattformbodens.

Hinweis: Geben Sie die Abmessungen Ihrer Plattform im beigefügten Ersatzteil-

Bestellformular an.

Page is loading ...

Terex Genie AWP Series Installation Instructions Manual

Terex Genie AWP Series Installation Instructions Manual

in other languages

Related papers

Other documents