Juniper SRX210 - DESK MOUNTING KIT Quick start guide

Brand: Juniper

Model: SRX210 - DESK MOUNTING KIT

Type: Quick start guide

Juniper SRX210 - DESK MOUNTING KIT is a mounting accessory designed to securely attach your SRX210 Services Gateway to a desk or other flat surface, providing stability and ease of access. Its compact design allows for efficient use of space, while the sturdy construction ensures reliable support for your networking equipment. The kit includes all necessary hardware for installation, making it a convenient and hassle-free solution for securing your SRX210 device in a desired location.

SRX210 Services Gateway Quick Start

Use the instructions in this quick start to help you connect the SRX210 Services

Gateway to your network. For details, see the SRX210 Services Gateway Hardware

Guide at http://www.juniper.net/techpubs/a057.html

SRX210 Services Gateway (SRX210B, SRX210H, SRX210H-POE) Front

Panel

SRX210 Services Gateway with Integrated Convergence Services

(SRX210H-P-MGW) Front Panel

SRX210 Services Gateway (All Models) Back Panel

SRX210 Services Gateway Models

The following four models of SRX210 Services Gateways are available:

On the SRX210H-POE and SRX210H-P-MGW models, Power over Ethernet (PoE) of 50

watts is supported across 4 ports (0/0, 0/1, 0/2, and 0/3).

Connecting and Configuring the SRX Series Device

Use the instructions below to connect and set up the SRX210 Services Gateway to

protect your network. Refer to the LEDs on the front of the device to help you determine

the status of the device.

Task 1: Overview

The SRX210 Services Gateway is a security device that requires these basic

configuration settings to function:

 Interfaces must be assigned IP addresses.

 Interfaces must be bound to zones.

 Policies must be configured between zones to permit or deny traffic.

Callout Description Callout Description

1 Mini-PIM slot 5 USB ports

2 Power button 6 Console port

3 LEDs (ALARM, POWER,

STATUS, HA, mPIM, EXPCARD)

7 Gigabit Ethernet (0/0 and 0/1) and Fast

Ethernet (0/2 to 0/7) ports

4 Reset Config button

Callout Description Callout Description

1 FXS and FXO voice ports 5 Reset Config button

2 Mini-PIM slot 6 USB ports

3 Power button 7 Console port

4 LEDs (ALARM, POWER, STATUS,

HA, mPIM, EXPCARD)

8 Gigabit Ethernet (0/0 and 0/1) and Fast

Ethernet (0/2 to 0/7) ports

g031132

g031101

Callout Description Callout Description

1 Power supply input 4 Lock for security cable

2 Cable tie holder 5 ExpressCard slot

3 Grounding point

Device DDR Memory Power over

Ethernet

Voice Support

SRX210B 512 MB No No

SRX210H 1 GB No No

SRX210H-POE 1 GB Yes No

SRX210H-P-MGW 1 GB Yes Yes

g031113

Page 2

 Source NAT rules must be set.

The device has the following default configuration set when you power it on for the first

time. To be able to use the device, you do not need to perform any initial configuration.

Factory-Default Settings:

Factory-Default Settings for Security Policies:

Factory-Default Settings for NAT Rule:

Task 2: Connect the Power Cable and a Power Source

Connect the power cable to the device and a power source. We recommend using a

surge protector. Note the following indications:

 POWER LED (green): The device is receiving power.

 STATUS LED (green): The device is operating normally.

 ALARM LED (amber): The device is operating normally, and may glow amber as a

rescue configuration has not been set. This is not a panic condition.

 mPIM LED (off): The Mini-Physical Interface Module (Mini-PIM) is not present or is

not detected by the device. If this LED is green and steadily on, it indicates that the

Mini-PIM is functioning normally.

NOTE: After a rescue configuration has been set, an amber ALARM LED indicates a

minor alarm, and a solid red ALARM LED indicates a major problem on the services

gateway.

NOTE: You must allow the device between 5 and 7 minutes to boot up after you power it

on. Wait until the STATUS LED is solid green before proceeding to the next task.

Task 3: Connect the Management Device

Connect the management device to the services gateway using either of the following

methods:

 Connect an RJ-45 cable (Ethernet cable) from one of the following ports on the front

panel to the Ethernet port on the management device (workstation or laptop):

 0/1 (interface ge-0/0/1)

 0/2 through 0/7 (interfaces fe-0/0/2 through fe-0/0/7)

We recommend this connection method. If you are using this method to connect,

proceed with Task 4.

 Connect an RJ-45 cable (Ethernet cable) from the port labeled CONSOLE to the

supplied DB-9 adapter, which then connects to the serial port on the management

device. (Serial port settings: 9600 8-N-1.)

If you are using this method to connect, proceed with the CLI configuration

instructions in the Branch SRX Series Services Gateways Golden Configurations at

www.juniper.net/us/en/local/pdf/app-notes/3500153-en.pdf.

See the illustration below for details on connecting a management interface.

Task 4: Ensure That the Management Device Acquires an IP Address

After you connect the management device to the services gateway, the DHCP server

process on the services gateway will assign an IP address automatically to the

management device. Ensure that the management device acquires an IP address on the

192.168.1.0/24 subnetwork (other than 192.168.1.1) from the device.

NOTE: The services gateway functions as a DHCP server and will assign an IP address

to the management device.

NOTE: If an IP address is not assigned to the management device, manually configure

an IP address in the 192.168.1.0/24 subnetwork. Do not assign the 192.168.1.1 IP

address to the management device, as this IP address is assigned to the services

gateway. By default, the DHCP server is enabled on the L3 VLAN interface, (IRB) vlan.0

(ge-0/0/1 and fe-0/0/2 to fe-0/0/7), which is configured with an IP address of

192.168.1.1/24.

NOTE: When an SRX210 Services Gateway is powered on for the first time, it boots

using the factory default configuration.

Task 5: Ensure That an IP Address Is Assigned to the Services Gateway

Use one of the following methods to obtain an IP address on the services gateway:

Port Label Interface Security

Zones

DHCP State IP Address

0/0 ge-0/0/0 untrust client unassigned

0/1 and 0/2

to 0/7

ge-0/0/1 and

fe-0/0/2 to

fe-0/0/7

trust server 192.168.1.1/24

Source Zone Destination Zone Policy Action

trust untrust permit

trust trust permit

untrust trust deny

Source Zone Destination Zone Policy Action

trust untrust source NAT to untrust zone

interface

g031118

Page 3

 Method 1: Obtaining a Dynamic IP Address on Your Services Gateway

Use the port labeled 0/0 (interface ge-0/0/0) to connect to your Internet Service

Provider (ISP). Your ISP will assign an IP address using the DHCP process. If you

use this method, when you get to Task 7, skip steps 1 through 4.

 Method 2: Obtaining a Static IP Address on Your Services Gateway

Use the port labeled 0/0 (interface ge-0/0/0) to connect to your ISP. Your ISP will

have provided a static IP address. You will not receive an IP address using the

DHCP process. If you use this method, you must configure the static IP address on

the services gateway as described in Task 7, steps 1 through 4.

Task 6: Access the J-Web Interface

1. Launch a Web browser from the management device.

2. Enter http://192.168.1.1 in the URL address field.

3. Specify the default username as root. Do not enter any value in the Password field.

4. Click Log In. The J-Web Setup Wizard page appears.

Task 7: Configure the Basic Settings

Configure the basic settings, such hostname, domain name, and root password for your

services gateway.

IMPORTANT: Ensure that you have configured the IP address, root authentication,

and default gateway before you apply the configuration.

NOTE: All fields marked with an asterisk (*) are mandatory.

NOTE: All network and management access settings are optional.

If you used Method 2 in Task 5 to obtain an IP address on your services gateway, ensure

that you make the following J-Web modifications:

1. On the Configure System: Network Settings page of the wizard, enter the IP address

of the gateway in the Default Gateway field, and enter server names in the DNS

Name Servers list. Your ISP provides the IP address for the gateway and the server

names.

2. On the Configure Interfaces page of the wizard, select the ge-0/0/0.0 interface and

click Edit.

3. On the Add/Edit interface page, next to Address, clear DHCP and select IP

Address.

4. In the IP Address/subnet field, enter the manual IP address provided by your ISP.

The IP address must be entered in a.b.c.d/xx format, where xx is the subnet prefix.

NOTE: Make sure that you have selected the required services and protocols under

Services (Inbound) and Protocols (Inbound). Select all to permit all protocols and

services.

NOTE: You can use the Configure J-Web Preferences page of the wizard to set the

J-Web starting page options and J-Web commit options.

Task 8: Apply the Basic Configuration

On the last page (Review and Commit) of the wizard, review the basic configuration and

click Commit to apply the configuration.

After you configure the basic settings, the J-Web Setup wizard redirects you to the

J-Web pages where you can continue working in the J-Web interface.

After you complete initial setup configuration, the Setup wizard is no longer available. To

make changes to the configuration, use the J-Web interface.

NOTE: To make any changes to the interface configuration, see the Branch SRX Series

Services Gateways Golden Configurations at

http://www.juniper.net/us/en/local/pdf/app-notes/3500153-en.pdf.

Page 4

Task 9: Verify the Configuration

Access http://www.juniper.net to ensure that you are connected to the internet. This

connectivity ensures that you can pass traffic through the services gateway.

NOTE: If the http://www.juniper.net page does not load, verify your configuration settings,

and ensure that you have applied the configuration.

After you complete these steps, you can pass traffic from any trust port to the untrust

port.

Connecting and Configuring the SRX210 Services Gateway with

Integrated Convergence Services

If you have an SRX210H-P-MGW model, use the following instructions to configure voice

support on the media gateway and to get started using your device to place and receive

calls.

The following table provides an overview of the steps you follow to configure voice

support on the media gateway.

The following tables list the factory default settings on the SRX210 Services Gateway

with Integrated Convergence Services:

Factory-Default Settings for the Voice Ports:

Factory-Default Settings for the Dial Plan on the Services Gateway:

Factory-Default Settings for the Class of Restriction on the Services Gateway:

Task 1: Connect the FXS and FXO Ports

1. Connect an FXS port (FXS1 or FXS2) on the device to an analog device, such as a

telephone, fax, or modem, through an RJ-11 cable.

2. Connect an FXO port (FXO1 or FXO2) on the device to the central office (CO)

switches or to a station port on a PSTN through an RJ-11 cable.

3. Connect an Ethernet cable from any of the PoE ports (ge-0/0/0, ge-0/0/1, fe-0/0/2,

fe-0/0/3) to the VoIP phone.

Task 2: Access the J-Web Interface

1. Launch a Web browser from the management device.

2. Log in using the credentials you set during the initial configuration described in the

“Connecting and Configuring the SRX210 Services Gateway” section.

3. The Configure page appears.

Task 3: Configure the Class of Restriction

Configure the class of restriction to define the policy dedicated to specifying call type

permissions:

1. Select Configure > Convergence Services > Station > Class of Restriction. The

Class of Restriction Configuration page appears.

2. Click Add to create a new class of restriction. The New Class of Restriction page

appears.

3. Enter the name in the Class of Restriction field.

4. Click Add to add a new policy to the class of restriction you are creating. The New

Policy Configuration page appears.

5. Perform the following actions:

NOTE: By default, the device allows intrabranch, local, emergency, and long distance

calls. International and 900 calls are denied by default.

Step Task Step Task

1 Connect the FXO and FXS ports. 7 Configure the trunk.

2 Access the J-Web interface. 8 Configure trunk groups.

3 Configure the class of restriction. 9 Create the dial plan.

4 Configure the SIP station. 10 Configure the media gateway.

5 Configure the analog station. 11 Configure the survivable call server.

6 Configure the peer call server.

Port Label Interface Extension Station/Trunk Name

FXS1 fxs-0/0/10 3001 3001

FXS2 fxs-0/0/11 3002 3002

FXO1 fxo-0/0/12 - fxo1

FXO2 fxo-0/0/13 - fxo2

Call Pattern Call Type Call Type Name

911 Emergency emergency-call

1XXXXXXXXXX Long distance long-distance-call

XXXXXXX Local local-call

011. International international-call

1900. 900 number 900-number

Call Pattern Call Type

Allow Intrabranch

Local

Long distance

Emergency

Deny International

900 number

Field Action

Policy Name Specify a name for the policy.

Available Call Types Select the call types applicable to your setup.

Permissions Set permissions (allow or deny) on the selected call

types.

Page 5

Task 4: Configure the SIP Station

NOTE: For initial configuration of the device, you do not need to configure the station

templates. You can use the default values.

1. Select Configure > Convergence Services > Station. The Station Configuration

page appears.

2. Click Add to add the new station, and perform the following mandatory basic

actions:

NOTE: You can configure the analog templates to be similar so that they can share a

common configuration.

NOTE: You can use station templates to configure stations so that they share a common

configuration. By default, templates are available for both SIP and analog stations. For

SIP stations, the extension range is 5001 through 5016.

Task 5: Configure the Analog Station

1. Select Configure > Convergence Services > Station. The Station Configuration

page appears.

2. Click Add to add the new station, and perform the following mandatory basic

actions:

You can configure the individual SIP stations similarly so that they can share a common

configuration.

NOTE: By default, templates are available for both SIP and analog stations.

Task 6: Configure the Peer Call Server

Configure the peer call server that provides call routing and call handling services for the

branch as long as it is accessible:

1. Select Configure > Convergence Services > Call Server. The Peer Call Server

Configuration page appears.

2. Perform the following mandatory basic actions:

When configuring the peer call server:

 For the device to authenticate itself with the peer call server, you might need to

provide the device user ID and password details as provided by the peer call

server’s administrator.

 You can accept the default values in the Port (5060) and Transport (UDP) fields.

 For initial configuration of the device, you do not need to specify the codec. The

default set of codecs is used. By default, codecs are specified in the following order:

711-µ, G711-A, G729AB

Task 7: Configure a Trunk

Configure a trunk for a PSTN time-division multiplexing (TDM) interface to be used by

the device or the survivable call server to route calls to the destination.

1. Select Configure > Convergence Services > Gateway > Trunks. The New Trunk

Configuration page appears.

2. Perform the following actions:

NOTE: By default, the two onboard FXO ports are configured as part of a default group

called the Branch_Trunk_Group, which will enable you to make calls using the FXO trunk

ports.

Task 8: Configure the Trunk Groups

A trunk group comprises multiple trunks specified in the order of precedence in which

they must be selected to route a call.

1. Select Configure > Convergence Services > Gateway > Trunk Groups. The

Trunk Group Configuration page appears.

2. Click Add to create a new trunk group and perform the following mandatory actions:

Field Action

Name Specify a name for the station.

Extensions Enter the extension number of the station.

Class of Restriction Select the already configured class of restriction.

Template Name Select the already defined station template.

Field Action

Name Specify a name for the station.

Extensions Enter the extension number of the station.

Class of Restriction Select the already configured class of restriction.

Template Name Select the already defined station template. In

addition, the default extensions are also configured for

the two onboard FXS ports.

TDM Interface Specify the type of TDM interface to be configured

(FXO, FXS, or T1).

Field Action

Name Specify the name for the peer call server.

PSTN Access Number Specify the external PSTN number for the survivable

call server to use if it must contact the PSTN directly.

Address Type Select the address type as either fqdn or

ipv4-address.

FQDN Enter the fully qualified domain name.

IP Address Enter the IP address of the peer call server.

Field Action

Trunk Name Enter a name for the trunk

Trunk Type Select the trunk type (FXO, FXS, or T1).

TDM Interface Select the type of TDM interface to be configured

(FXO, FXS, or T1) for routing certain types of calls.

Field Action

Name Specify a name for the trunk group.

Available Trunks Select the trunks applicable to your setup.

Juniper Networks, Junos, Steel-Belted Radius, NetScreen, and ScreenOS are registered trademarks of Juniper Networks, Inc. in the United States and other countries. The Juniper Networks Logo, the Junos logo, and JunosE are

trademarks of Juniper Networks, Inc. All other trademarks, service marks, registered trademarks, or registered service marks are the property of their respective owners. Juniper Networks assumes no responsibility for any inaccuracies

in this document. Juniper Networks reserves the right to change, modify, transfer, or otherwise revise this publication without notice. Products made or sold by Juniper Networks or components thereof might be covered by one or more

of the following patents that are owned by or licensed to Juniper Networks: U.S. Patent Nos. 5,473,599, 5,905,725, 5,909,440, 6,192,051, 6,333,650, 6,359,479, 6,406,312, 6,429,706, 6,459,579, 6,493,347, 6,538,518, 6,538,899,

Task 9: Create the Dial Plan

Create the dial plan to enable the survivable call server and media gateway to determine

how calls are routed:

1. Select Configure > Convergence Services > Dial Plan, and click on Dial Plan.

The Dial Plan Configuration page appears.

1. Click Add to create a new dial plan. The New Dial Plan Configuration page appears.

2. Enter a name in the Dial Plan Name field, and click Add. The New Route Pattern

Configuration page appears.

3. Perform the following mandatory basic actions:

You can accept the default values for the Preference and Digit Manipulation fields.

Task 10: Configure the Media Gateway

Configure the media gateway to enable routing of calls to and from trunks and analog

phones connected to the device when the peer call server is accessible:

1. Select Configure > Convergence Services > Media Gateway > Gateway. The

Media Gateway Configuration page appears.

2. Click Add, and enter the following mandatory settings:

You can accept the default values in the Port (5060) and Transport (UDP) fields.

Task 11: Configure the Survivable Call Server

This server assumes the responsibilities of the peer call server when the peer call server

is unreachable:

1. Select Configure > Convergence Services > Call Service. The Survivable Call

Service page appears.

2. Click Add to create a new call service, and perform the following mandatory basic

actions:

All other parameters for configuring the call service are optional and you can accept the

default values set for these parameters.

Powering Off the Device

You can power off the device in one of the following ways:

 Graceful shutdown—Press and immediately release the Power button. The device

begins gracefully shutting down the operating system.

 Forced shutdown—Press the Power button, and hold it for 10 seconds. The device

immediately shuts down. Press the Power button again to power on the device.

You can reboot or halt the system in the J-Web interface by selecting Maintain >

Reboot.

For additional configuration information, see the Branch SRX Series Services Gateways

Golden Configurations at

http://www.juniper.net/us/en/local/pdf/app-notes/3500153-en.pdf.

For detailed software configuration information, see the software documentation

available at http://www.juniper.net/techpubs/software/junos-srx/index.html.

Contacting Juniper Networks

For technical support, see www.juniper.net/support/requesting-support.html.

Step Task

Route Pattern Specify the route pattern name.

Call Type Select the call type. The default is trunk-call.

Trunk-groups Select the preconfigured trunk groups to include in the

route pattern.

Step Task

Media Gateway Specify the device name.

Call Server Select a peer call server with which to associate.

Dial Plan Select a preconfigured dial plan.

Zone Specify the service point for the device’s zone to

enable the media gateway and survivable call server

services for the specified zone.

Step Task

Call Service Name Specify the name for the call service.

Call Server Select the peer call server name.

Dial Plan Select the preconfigured dial plan to be used for the

survivable call server.

Zone Specify the name for the zone.

Juniper SRX210 - DESK MOUNTING KIT Quick start guide

Juniper SRX210 - DESK MOUNTING KIT Quick start guide

Juniper SRX210 - DESK MOUNTING KIT Quick start guide

Related papers

Other documents