Patton SmartNode SN4150 User manual

Brand: Patton

Model: SmartNode SN4150

Category: VoIP telephone adapters

Type: User manual

This manual is also suitable for

SmartNode SN5550

SmartNode SN5550 and SN4150

Enterprise Session Border Control-

ler, Integrated Access Device, and

VoIP Gateway

User Manual

Sales Office: +1 (301) 975-1000

Technical Support: +1 (301) 975-1007

E-mail: support@patton.com

WWW: www.patton.com

Part Number: 07MDSN5550-SN4150-UM Rev. D

Revised: July 30, 2018

Important

This is a Class A device and is intended for use in a light industrial environment. It is

not intended nor approved for use in an industrial or residential environment.

Patton Electronics Company, Inc.

7622 Rickenbacker Drive

Gaithersburg, MD 20879 USA

tel: +1 (301) 975-1000

fax: +1 (301) 869-9293

support: +1 (301) 975-1007

web: www.patton.com

e-mail: [email protected]

Trademark Statement

The terms SmartWare, SmartNode, and Trinity OS are trademarks of Patton Electronics

Company. All other trademarks presented in this document are the property of their

respective owners.

The information in this document is subject to change without notice. Patton Elec-

tronics assumes no liability for errors that may appear in this document.

Warranty Information

The software described in this document is furnished under a license and may be used

or copied only in accordance with the terms of such license.

Patton Electronics warrants all SmartNode router components to be free from

defects, and will—at our option—repair or replace the product should it fail within

one year from the first date of the shipment.

This warranty is limited to defects in workmanship or materials, and does not cover

customer damage, abuse or unauthorized modification. If the product fails to perform

as warranted, your sole recourse shall be repair or replacement as described above.

Under no condition shall Patton Electronics be liable for any damages incurred by

the use of this product. These damages include, but are not limited to, the following:

lost profits, lost savings and incidental or consequential damages arising from the use

of or inability to use this product. Patton Electronics specifically disclaims all other

warranties, expressed or implied, and the installation or use of this product shall be

deemed an acceptance of these terms by the user.

Summary Table of Contents

1 General information........................................................................................................................................ 15

2 Applications overview...................................................................................................................................... 26

3 SmartNode Installation ................................................................................................................................... 30

4 Initial Configuration ....................................................................................................................................... 38

5 Contacting Patton for Assistance...................................................................................................................... 46

A Compliance Information ................................................................................................................................ 49

B Specifications ................................................................................................................................................. 52

C Cabling .......................................................................................................................................................... 59

D Port pin-outs .................................................................................................................................................. 66

E SmartNode Device Factory Configuration ....................................................................................................... 70

F Reset Button Functions .................................................................................................................................. 72

G End User License Agreement .......................................................................................................................... 78

Table of Contents

About this guide......................................................................................................................................................... 10

Audience............................................................................................................................................................... 10

Structure............................................................................................................................................................... 10

Precautions ........................................................................................................................................................... 10

Safety when working with electricity............................................................................................................... 11

Deutsch ..........................................................................................................................................................12

General observations .......................................................................................................................................13

Typographical conventions used in this document................................................................................................ 13

General conventions .......................................................................................................................................13

1 General information .........................................................................

.................................................................15

SmartNode devices overview .................................................................................................................................16

SmartNode SN5550 eSBC .............................................................................................................................17

Port descriptions .......................................................................................................................................19

Front panel LED definitions .....................................................................................................................20

SmartNode SN4150 VoIP Gateway ................................................................................................................21

Port descriptions .......................................................................................................................................23

Front panel LED definitions .....................................................................................................................24

2 Applications overview ................

........................................................................................................................26

Introduction..........................................................................................................................................................27

Application for SmartNode SN5550 eSBC............................................................................................................27

Application for SmartNode SN4150 VoIP Gateway..............................................................................................28

3 SmartNode Installation.........................................................................

.............................................................30

Planning the Installation........................................................................................................................................31

Site log ............................................................................................................................................................31

Network information ......................................................................................................................................31

Network Diagram ...........................................................................................................................................31

IP related information .....................................................................................................................................31

Software tools .................................................................................................................................................32

Power source ...................................................................................................................................................32

Location and mounting requirements .............................................................................................................32

Installing the SmartNode device ............................................................................................................................32

Placing the SmartNode device .........................................................................................................................32

Connecting cables ...........................................................................................................................................33

Installation cable requirements for the WAN interface (SN5550 /2G, /4G, /AVA, /AVB /F Models) .......33

Installation cable requirements for the SFP for Fiber WAN module (SN5550) .........................................33

Connecting ISDN terminals and NT to the SmartNode device’s ISDN BRI ports ...................................33

Installing an interface cable on the SmartNode device’s FXS and FXO interface ports

..............................35

Connecting the 10/100/1000Base-T Ethernet LAN and WAN cables ......................................................36

Connecting the power supply ....................................................................................................................36

SmartNode 5550 & 4150 Series User Manual

4 Initial Configuration..........................................................................................................................................38

Introduction..........................................................................................................................................................39

Connecting the SN5550 - SN4150/2ETH to your laptop PC...............................................................................39

Configure the desired IP address .....................................................................................................................40

Factory-default IP Settings ........................................................................................................................40

Login ........................................................................................................................................................40

Changing the WAN IP address .................................................................................................................40

Connecting the SmartNode device to the network ..........................................................................................41

Connecting the SN4150 to a laptop PC ................................................................................................................42

Configure the Desired IP Address ...................................................................................................................43

Factory-default IP Settings ........................................................................................................................43

Login ........................................................................................................................................................44

Changing the WAN IP address .................................................................................................................44

Loading the Configuration (optional)....................................................................................................................45

Additional Information .........................................................................................................................................45

5 Contacting Patton for Assistance............................

............................................................................................46

Introduction..........................................................................................................................................................47

Contact information..............................................................................................................................................47

Contacting Patton Technical Services for Free Support ...................................................................................47

Warranty Service and Returned Merchandise Authorizations (RMAs)...................................................................47

Warranty coverage ..........................................................................................................................................47

Out-of-warranty service .............................................................................................................................48

Returns for credit ......................................................................................................................................48

Return for credit policy .............................................................................................................................48

RMA numbers ................................................................................................................................................48

Shipping instructions ................................................................................................................................48

A Compliance Information .............................................................................

......................................................49

Compliance...........................................................................................................................................................50

EMC ...............................................................................................................................................................50

Safety ..............................................................................................................................................................50

Radio and TV interference ....................................................................................................................................50

CE Declaration of Conformity ..............................................................................................................................50

Authorized European Representative .....................................................................................................................50

ISDN Compliance ................................................................................................................................................51

B Specifications ........................

............................................................................................................................52

DSP.......................................................................................................................................................................53

Voice Connectivity................................................................................................................................................53

Data Connectivity .................................................................................................................................................53

Voice Processing (signaling dependent) .................................................................................................................53

Fax and modem support........................................................................................................................................54

Voice Signaling......................................................................................................................................................54

Voice Routing—session router ..............................................................................................................................54

IP Services .............................................................................................................................................................55

SmartNode 5550 & 4150 Series User Manual

WAN Interface (if applicable)................................................................................................................................56

Management .........................................................................................................................................................57

System...................................................................................................................................................................57

Physical .................................................................................................................................................................57

C Cabling ......................................................................................

.......................................................................59

Introduction..........................................................................................................................................................60

Ethernet ................................................................................................................................................................60

Analog FXS ...........................................................................................................................................................61

Analog FXO ..........................................................................................................................................................63

ISDN BRI.............................................................................................................................................................64

D Port pin-outs .............

.......................................................................................................................................66

Introduction..........................................................................................................................................................67

Ethernet ...............................................................................................................................................................67

FXS port................................................................................................................................................................67

FXO port ..............................................................................................................................................................68

ISDN BRI (NT/Net or TE/User) ports.................................................................................................................68

G.SHDSL EFM & ATM port (/2G and /4G models)...........................................................................................68

VDSL-ADSL Port (/A and /AVA & /AVB models only) .......................................................................................69

Fiber Ports (/F models only) ..................................................................................................................................69

E SmartNode Device Factory Configuration ...........................................

..............................................................70

Introduction..........................................................................................................................................................71

F Reset Button Functions .................................

....................................................................................................72

Introduction

..........................................................................................................................................................73

Resetting the SmartNode device when it is operating and the Power LED is lit.....................................................76

Resetting the SmartNode device when it is initially powered off............................................................................76

G End User License Agreement ............................................................................................

.................................78

End User License Agreement .................................................................................................................................79

1. Definitions ..................................................................................................................................................79

2. Title ............................................................................................................................................................79

3. Term ...........................................................................................................................................................79

4. Grant of License ..........................................................................................................................................79

5. Warranty ....................................................................................................................................................80

6. Termination ................................................................................................................................................80

7. Notices .......................................................................................................................................................80

8. Other Licenses ............................................................................................................................................80

9. Unenforceable Provisions ............................................................................................................................81

10. Governing Law .........................................................................................................................................81

11. Waiver ......................................................................................................................................................81

List of Figures

1 SmartNode SN5550 eSBC and SN4150 Gateway . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

2 Examples of SN5550 rear panels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

3 SmartNode SN5550 front panels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

4 Examples of SN4150 rear panels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22

5 SmartNode SN4150 front panels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

6 SN5550 application . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27

7 SN4150 application . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28

8 Connecting an ISDN device . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34

9 Rear view showing location of Ethernet, FXO, and FXS connectors, and ground lug (SmartNode 5550 shown) .

10 Power LED . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37

11 Connecting the SmartNode device to your laptop PC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39

12 Connecting the SmartNode to the network . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41

13 Connecting the SmartNode to a laptop PC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42

14 Connecting SmartNode device and PC to a LAN with DHCP server. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43

15 Typical Ethernet straight-through cable diagram for 10/100Base-T . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60

16 Typical Ethernet straight-through cable diagram for 1000Base-T . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60

17 Connecting an FXS device . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61

18 RJ-11 pin-out diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62

19 Connecting to an FXO line socket . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63

20 Connecting an ISDN device . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64

21 ISDN BRI RJ-45 pin-out diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65

22 RJ11 and RJ45 pin comparison . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 69

23 SN4150 Reset button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 74

24 SN5551 Reset button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 75

25 Reset button periods (in seconds) for performing actions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 76

List of Tables

1 General conventions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

2 Rear panel ports . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

3 SmartNode SN5550 LED Definitions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

4 Rear panel ports . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

5 SmartNode SN4150 LED Definitions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25

6 Sample site log entries . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31

7 Factory Default IP Address and Network Mask Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40

8 Factory Default IP Address and Network Mask Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43

9 WAN Interface Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56

10 RJ-11 socket . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62

11 RJ-45 male connector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65

12 10/100 Base-T RJ-45 socket . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67

13 1000Base-T RJ-45 Socket . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67

14 RJ-11 socket . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67

15 RJ-45 Socket . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 68

16 EFM Port . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 69

17 VDSL/ADSL Port: RJ-45 connector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 69

18 Results from pressing the Reset button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 76

19 Using the Reset button to switch to a backup image or erase flash memory . . . . . . . . . . . . . . . . . . . . . . . . . . . 77

About this guide

This guide describes the SmartNode SN5550 and SN4150 hardware, installation and basic configuration. For

detailed software configuration information refer to the

Trinity Command Line Reference Guide and the avail-

able Configuration Notes.

Audience

This guide is intended for the following users:

• Operators

• Installers

• Maintenance technicians

Structure

This guide contains the following chapters and appendices:

• Chapter 1, starting on page 15, provides information about SmartNode devices features and capabilities

• Chapter 2, starting on page 26, contains an overview describing SmartNode devices operation and applica-

tions

• Chapter 3, starting on page 30, provides SmartNode device installation procedures

• Chapter 4, starting on page 38, leads you through the steps to set up a new SmartNode device and down-

load a configuration

• Chapter 5, starting on page 46, contains information on contacting Patton technical support for assistance

• Appendix A, starting on page 49, provides compliance info for the SmartNode devices

• Appendix B, starting on page 52, contains specifications for the SmartNode devices

• Appendix C, starting on page 59, provides cable recommendations

• Appendix D, starting on page 66, describes the SmartNode devices’ ports and pin-outs

• Appendix E, starting on page 70, describes how to obtain factory configuration settings for the SmartNode

devices

• Appendix F, starting on page 72, describes the Reset button functions

• Appendix G, starting on page 78, provides the End User License Agreement

For best results, read the contents of this guide before you install a SmartNode device.

Precautions

Notes and cautions, which have the following meanings, are used throughout this guide to help you become

aware of potential SmartNode device problems. Warnings relate to personal injury issues, and Cautions refer to

potential property damage.

SmartNode 5550 & 4150 Series User Manual

Note Calls attention to important information.

Safety when working with electricity

The shock hazard symbol and WARNING heading indicate a potential electric

shock hazard. Strictly follow the warning instructions to avoid injury caused by

electric shock.

The alert symbol and WARNING heading indicate a potential safety hazard.

Strictly follow the warning instructions to avoid personal injury.

The shock hazard symbol and CAUTION heading indicate a potential electric shock haz-

ard. Strictly follow the instructions to avoid property damage caused by electric shock.

The alert symbol and CAUTION heading indicate a potential hazard. Strictly follow the

instructions to avoid property damage.

The SmartNode device contains no user serviceable parts, and is not be opened

by the user. The equipment shall be returned to Patton Electronics for repairs or

repaired by qualified service personnel.

Mains Voltage: In systems without a power switch, line voltages are present in the

power supply when the power cord is connected. The mains outlet used to power

the SmartNode device shall be within 10 feet (3 meters) of the device, be easily

accessible, and protected by a circuit breaker.

For AC powered units, ensure that the power cable used meets all applicable stan-

dards for the country in which it is to be installed, and that it is connected to a wall

outlet which has earth ground.

For units with an external power adapter, the adapter shall be a listed Limited

Power Source.

Hazardous network voltages are present in WAN ports regardless of whether

power to the SmartNode is ON or OFF. To avoid electric shock, use caution when

near WAN ports. When detaching the cables, detach the end away from the Smart

Node first.

WARNING

CAUTION

WARNING

SmartNode 5550 & 4150 Series User Manual

Deutsch

Warnhinweise:

Before handling the device, disconnect the telephone network cables to avoid

contact with telephone line voltages. When detaching the cables, detach the end

away from the SmartNode device first.

Do not work on the system or connect or disconnect cables during periods of

lightning activity.

Dieses Gerät ist NICHT für den Anschluss an das Telefonnetz (PSTN) bestimmt

und auch NICHT dafür zugelassen. Es ist nur für den Anschluss an Endgeräte

beim Kunden vorgesehen.

• Das Gerät entält keine austauschbaren Komponenten und ist vom Benutzer nicht zu

öffnen. Bei Systemen ohne Netzschalter und ohne externes Netzteil liegt Netzspan

nung im Gerät an, wenn das Netzkabel angeschlossen ist.

• Bei Geräten mit externem Netzteil muss das Netzteil die Anforderungen an eine zuge-

lassene Stromquelle mit begrenzter Leistung erfüllen. Die Steckdose, die für die

Stromversorgung des Gerätes verwendet wird, sollte höchstens 3 Meter vom Gerät

entfernt und leicht zugänglich sein sowie durch einen den örtlichen regulatorischen

Anforderungen entsprechenden Schutzschalter abgesichert sein.

• Für mit Wechselstrom betriebene Geräte muss sichergestellt sein, dass das verwen-

dete Netzkabel alle gültigen Normen des Landes erfüllt, in dem es eingesetzt werden

soll.

• Für mit Wechselstrom betriebene Geräte, die 3-polige Netzstecker haben (L1, L2 u.

GND oder Phase, Neutralleiter u. Schutzleiter), muss die Steckdose geerdet sein.

• Für mit Gleichstrom betriebene Geräte muss sichergestellt sein, dass die Verbindung-

skabel für Spannung, Strom, erwartete Temperatur, Entflammbarkeit und mecha-

nische Wartbarkeit geeignet sind.

• WAN-, LAN- u. PSTN-Ports (Anschlüsse) können unter gefährlicher Spannung ste-

hen, unabhängig davon, ob das Gerät ein- oder ausgeschaltet ist. PSTN bezieht sich

auf Schnittstellen wie Telefon, FXS, FXO, DSL, xDSL, T1, E1, ISDN, Voice, usw. Diese

sind als „gefährliche Netzwerkspannungen“ bekannt. Um einen elektrischen Schlag

zu vermeiden, muss in der Nähe dieser Anschlüsse mit Vorsicht gearbeitet werden.

Werden Kabel von diesen Anschlüssen getrennt, zuerst das Kabel am anderen Ende

herausziehen.

• Während eines Gewitters darf nicht am Gerät gearbeitet werden und es dürfen keine

Kabel angeschlossen oder vom Netz getrennt werden.

WARNING

WARNUNG

SmartNode 5550 & 4150 Series User Manual

General observations

• Clean the case with a soft slightly moist anti-static cloth

• Place the unit on a flat surface and ensure free air circulation

• Avoid exposing the unit to direct sunlight and other heat sources

• Protect the unit from moisture, vapors, and aggressive liquids

Typographical conventions used in this document

This section describes the typographical conventions and terms used in this guide.

General conventions

The procedures described in this manual use the following text conventions:

In Übereinstimmung mit den Anforderungen der Richtlinie 2002/96/EG über Elektro- und

Elektronik-Altgeräte (WEEE) muss sichergestellt sein, dass Altgeräte von anderem Abfall

und Schrott getrennt werden und dem Sammel- und Verwertungssystem für Elektro- und

Elektronik-Altgeräte in Ihrem Land zum Recycling zugeführt werden.

Do not stack multiple SmartNode devices directly on top of one another, and do not place

items on top of the device. If you will be installing equipment above the SmartNode device,

leave at least 2 inches (5 cm) of clearance between the devices.

Furthermore, leave at least 2 inches (5 cm) to the left, right, front, and rear of the SmartNode

device for proper ventilation.

In accordance with the requirements of council directive 2002/96/EC on Waste of Electri-

cal and Electronic Equipment (WEEE), ensure that at end-of-life you separate this product

from other waste and scrap and deliver to the WEEE collection system in your country for

recycling.

Table 1. General conventions

Convention Meaning

Garamond blue type

Indicates a cross-reference hyperlink that points to a figure, graphic, table, or sec-

tion heading. Clicking on the hyperlink jumps you to the reference. When you

have finished reviewing the reference, click on the Go to Previous View

button in the Adobe® Acrobat® Reader toolbar to return to your starting point.

Helvetica bold type Commands and keywords are in boldface font.

Helvetica bold-italic type Parts of commands, which are related to elements already named by the user,

are in boldface italic font.

Italicized Helvetica type Variables for which you supply values are in italic font

Helvetica type Indicates the names of fields or windows.

Garamond bold type Indicates the names of command buttons that execute an action.

< > Angle brackets indicate function and keyboard keys, such as <SHIFT>, <CTRL>,

<C>, and so on.

[ ] Elements in square brackets are optional.

CAUTION

SmartNode 5550 & 4150 Series User Manual

{a | b | c} Alternative but required keywords are grouped in braces ({ }) and are separated

by vertical bars ( | )

blue screen Information you enter is in blue screen font.

screen Terminal sessions and information the system displays are in screen font.

node The leading IP address or nodename of a SmartNode is substituted with node in

boldface italic font.

SN The leading SN on a command line represents the nodename of the SmartNode

# An hash sign at the beginning of a line indicates a comment line.

Table 1. General conventions (Continued)

Convention Meaning

Chapter 1 General information

Chapter contents

SmartNode devices overview .................................................................................................................................16

SmartNode SN5550 eSBC .............................................................................................................................17

Port descriptions .......................................................................................................................................19

Front panel LED definitions .....................................................................................................................20

SmartNode SN4150 VoIP Gateway ................................................................................................................21

Port descriptions .......................................................................................................................................23

Front panel LED definitions .....................................................................................................................24

SmartNode devices overview 16

SmartNode 5550 & 4150 Series User Manual 1 • General information

SmartNode devices overview

The SmartNode SN5550 Enterprise Session Border Controller (eSBCs)/Integrated Access Device (IAD) series

and SN4150 VoIP Gateway series (see figure 1) combo configuration of 2 BRI/2 FXS or 4 BRI/4FXS or in

addition with 2 or 4 FXO ports, fits the requirements of small and medium-sized enterprises requiring a solu

tion to enable legacy equipment for VoIP networks. Both combine IP routing, VoIP security and quality of ser-

vice (QoS) for up to 4/8 voice and FAX calls over any IP. The SmartNode devices deliver the legacy phone

interfaces, service transparency, and flexible integration required for All-IP networks. Both also offer the

optional embedded PacketSmart Agent for network monitoring and assessment 24x7.

Figure 1. SmartNode SN5550 eSBC and SN4150 Gateway

• The SmartNode SN5550 and SN4150 comprise several models: see the complete SKU list on the correspond-

ing product page on www.patton.com.

• The SmartNode SN5550 eSBC and SN4150 VoIP Gateways are equipped with 2 ISDN BRI S0/T0 and 2

FXS ports (some Models in addition have 2 FXO ports) providing 4 G.722/G.711 or 4 T.38 calls simultane

ously or with 4 ISDN BRI S0/T0 and 4 FXS ports (some models in addition have 4 FXO ports) providing 8

G.722/G.711 or 8 T.38 calls simultaneously; one or two 10/100/1000 Base-T Ethernet ports; and a single

USB port (SN55xx and SN41xx/2ETH models); provides voice over IP (VoIP) using SIP; Internet access rout

ing (SN41xx license required); Stateful Firewall functions; extensive QoS functions; an optional PacketSmart

Agent for voice assessment and monitoring; and much more.

• The SmartNode SN5550 eSBC/IADs and SN4150 VoIP Gateways equipped with either:

• 2 ISDN BRI S0/T0 and 2 FXS ports (some models also have 2 FXO in addition) providing 4 G.722/G.711 or

4 T.38 calls simultaneously

• 4 ISDN BRI S0/T0 and 4 FXS ports (some models also have 2 FXO in addition) providing 8 or 16 G.722/

G.711 or 8 T.38 calls simultaneously

• providing the following major functionalities:

• Analog telephony to voice over IP (SIP) conversion for 2 or 4 analog phone ports (FXS)

• FXO interfaces (2 or 4, depending on model) for connection to PSTN used for Survivability

SmartNode devices overview 17

SmartNode 5550 & 4150 Series User Manual 1 • General information

• ISDN telephony to voice over IP (SIP) conversion for 2 or 4 ISDN Basic Rate Interfaces (BRI)

• Fax T.38 and G711 bypass support

• Modem bypass support

• Optional PacketSmart

• One Ethernet port (2 Ethernet ports for SN41xx/2ETH models)

• Stateful Firewall

• QoS

In addition, the eSBC supports:

• IP routing including RIP, GRE, BGP, VPN

• USB port

• SIP TLS/SRTP included

• SIP Registrar included

In addition, the IAD supports:

• WAN access termination (VDSL2, ADSL2/2+, SHDSL, Fiber SFP)

Section “SmartNode SN5550 eSBC” on page 17 provides more information on the device. Section “Smart-

Node SN4150 VoIP Gateway” on page 21 describes the SmartNode SN4150.

SmartNode SN5550 eSBC

The SmartNode SN5550 eSBC is a compact Enterprise Session Border Controller that supports 4 up to 8

voice calls (FXS and BRI to VoIP and vice-versa) (see

figure 2 on page 18), and up to 200 SIP-to-SIP calls

(non-transcoded). By default there are 4 SIP to SIP calls enabled. Additional calls can be enabled by loading

SNSW-1B licenses (additional charge). The IAD versions also have WAN uplink termination included, such as

Fiber-SFP, ADSL/VDSL or G.SHDSL (EFM/ATM).

On the product the following model code conventions apply:

• JS stands for FXS ports

• JO stands for FXO ports

• V stands for number of Voice Channels

• BIS stands for BRI ports (NT or TE)

• HP stands for High Precision Clock (less than 5 ppm)

• AVA stands for VDSL / ADSL (Annex A,L,M)

• AVB stands for VDSL/ADSL (Annex B,J)

• 2G stands for 2-pair G.SHDSL.bis

• 4G stands for 4-pair G.SHDSL.bis

1. Optional License required at additional charge

SmartNode devices overview 18

SmartNode 5550 & 4150 Series User Manual 1 • General information

• F stands for SFP slot being used for Fiber link termination

• EUI stands for external universal input power supply

Note For a complete listing of available models, refer to the SmartNode VoIP page

https://www.patton.com/products/voip-comparison.asp

Figure 2. Examples of SN5550 rear panels

SmartNode devices overview 19

SmartNode 5550 & 4150 Series User Manual 1 • General information

Port descriptions

The SmartNode SN5550 rear panel ports (see figure 2 on page 18) are described in table 2.

Table 2. Rear panel ports

Port Description

10/100/100

Ethernet ETH 0/0 & ETH 0/1

RJ-45 connectors that connect the SmartNode device to an Ethernet device

(e.g., a cable or DSL modem, LAN hub or switch).

Analog voice ports, FXS 0/

0—FXS 0/3

FXS RJ-11 (6 position, 4 wire) connectors that connect the device with an

analog terminal (a telephone, for example). FXS on-hook voltage is 48V

for each FXS port.

Analog voice ports, FXO 0/

0—FXO 0/3

FXO RJ-11 (6 position, 4 wire) connectors. These ports connect to FXS

devices such as the PSTN.

BRI 0/0—BRI 0/3 ports ISDN BRI TE/NT port, RJ-45 socket S0/T0 interface, connects the

SmartNode device with an ISDN device over an S/T bus, e.g. a PBX or

an NT. The port can be switched between TE and NT mode. The inter

face is internally terminated with 100 Ohm. Point-to-point or point-to-

multipoint configurable. If the port is in NT mode, a Phantom power sup-

ply can be switched on to supply connected phones with power.

Power The SmartNode device requires 12 VDC, 1.25 A power for operation.

Every SmartNode device comes with an external power supply converting

from AC to DC power (100–240 VAC, 50/60 Hz).

USB 2.0 USB 2.0 host port used to connect a USB 3G/4G cellular modem. A list of

supported USB models can be found in the release notes and in the Trinity

Command Line Reference Guide.

WAN interface SFP, VDSL-

ADSL, G.SHDSL (EFM-ATM)

The VDSL-ADSL, G.SHDSL, RJ-45 Ethernet and SFP slot status LEDs

are located on either side of the port. ACT (when lit or blinking) shows

activity, and LINK (when lit) shows that the port is connected. 1000 is

indicating when a Gigabit Ethernet link is established

Note: On VDSL-ADSL models (/AVA and /AVB) only, the ACT LED has

no function.

Reset The reset button has several functions, as described in appendix F,

“Reset Button Functions” on page 72.

SmartNode devices overview 20

SmartNode 5550 & 4150 Series User Manual 1 • General information

Figure 3. SmartNode SN5550 front panels

Front panel LED definitions

Figure 3 shows SmartNode SN5550 LEDs; the LED definitions are listed in table 3 on page 21.

SmartNode devices overview 21

SmartNode 5550 & 4150 Series User Manual 1 • General information

Note If an error occurs, all LEDs will flash for more than 5 seconds before the

device reboots.

SmartNode SN4150 VoIP Gateway

The SmartNode SN4150 is a compact VoIP Gateway that supports 4 up to 8 VoIP calls (see figure 4 on

page 22).

On the products the following model code conventions apply:

• 2ETH stands for 2 Ethernet ports

• JS stands for FXS ports

• JO stands for FXO ports

• BIS stands for BRI port (NT/TE)

• HP stands for High Precision Clock (less than 5 ppm)

• V stands for voice channels

• EUI stands for external universal input power supply

Table 3. SmartNode SN5550 LED Definitions

LED Description

Power When lit, indicates power is applied. Blinks fast during bootloader phase and blinks

slow during the boot process . Becomes solid when the system is up and running.

VoIP • When lit, indicates the SmartNode device is registered to a SIP server, or a SIP

device has registered to the SmartNode device.

Off indicates the unit is not configured or registered, or has no active directly routed

VoIP connection.

AUX 1 & AUX 2 • Auxiliary LEDs for future use.

Voice Ports FXS

0—FXS 3

• When lit, indicates FXS port is enabled. Flashes when there are ongoing or ringing

calls.

• Off when no line or phone is connected or the port is shutdown.

Voice Ports FXO

0—FXO 3

• In ‘Idle’ state LED is off

• In ‘Dialing’ or ‘Ringing’ state blink-frequency is 2 per second,

• In ‘Connected’ state blink-frequency is 1 per second

BRI 0—BRI 3 • When lit, indicates ISDN layer 1 and Layer 2 are active. Flashes when there are

ongoing calls.

• Off when no line or phone is connected or the port is shutdown.

ETH 0 & ETH 1 • When lit, indicates the Ethernet connection on the corresponding port has a link indi-

cation.

• Flashes when data is received or transmitted at the corresponding Ethernet port.

GIG 0 & GIG 1 • When lit, indicates Ethernet is connected to a 1000Mb network.

• Off when Ethernet is connected to a 10Mb or 100Mb network or not connected.

Page is loading ...

Patton SmartNode SN4150 User manual

Brand: Patton

Model: SmartNode SN4150

Category: VoIP telephone adapters

Type: User manual

This manual is also suitable for

SmartNode SN5550

Download PDF

report

Patton SmartNode SN4150 User manual

This manual is also suitable for

Patton SmartNode SN4150 User manual

Related papers

Other documents