WORX Tools Trimmer WG102 User manual

Brand: WORX Tools

Model: Trimmer WG102

Category: Grass trimmers

Type: User manual

This manual is also suitable for

WG102

Grass/Edge trimmer ENG

Coupe gazon/coupe bordure F

Cortadora/Bordeadora de Césped ES

Pag 05

Pag 12

Pag 19

WG102

Trilingual-WG102-M-060609.indd 1 2006-6-9 16:56:20

Trilingual-WG102-M-060609.indd 2 2006-6-9 16:56:20

Trilingual-WG102-M-060609.indd 3 2006-6-9 16:56:20

�

Trilingual-WG102-M-060609.indd 4 2006-6-9 16:56:21











A B C

D E F

G H I

Trilingual-WG102-M-060609.indd 5 2006-6-9 16:56:24

Grass/Edge trimmer ENG

TECHNICAL DATA

Rated Volts 120V~60Hz

Rated Current 4.5A

Rated No-Load Speed 8800 min

-1

Cutting Diameter 12”

Line Diameter 0.065”

Machine Weight 7lbs

1. REAR HANDLE

2. AUXILIARY HANDLE

3. UPPER LOCKING KNOB

4. LOWER LOCKING KNOB

5. AUXILIARY HANDLE LOCKING KNOB

6. SAFETY GUARD

7. SPACER GUARD

8. EDGER WHEEL

9. LINE CUTTER

10. TELESCOPIC SHAFT

11. CUTTING HEAD COVER (SEE FIG J)

12. CAP RELEASE LATCH (SEE FIG J)

13. SPOOL (SEE FIG J)

14. CUTTING HEAD (SEE FIG J)

15. EYELET (SEE FIG J)

16. LINE FEED BUTTON (SEE FIG I)

Trilingual-WG102-M-060609.indd 6 2006-6-9 16:56:26

Grass/Edge trimmer ENG

SAFETY INSTRUCTIONS

WARNING! When using electric

gardening appliances, basic safety

precautions must always be followed to reduce

the risk of ﬁre, electric shock, and serious injury,

including the following:

READ ALL INSTRUCTIONS

1. FOR ALL DOUBLE-

INSULATEDAPPLIANCES

a) Replacement parts. When servicing use

only identical replacement parts.

b) Polarized appliance connections. To reduce

the risk of electric shock, this appliance

has a polarized plug (one blade is wider

than the other} and will require the use of

a polarized extension cord. The appliance

plug will ﬁt into a polarized extension cord

only one way. If the plug does not ﬁt fully

into the extension cord, reverse the plug. If

the plug still does not ﬁt, obtain a correct

polarized extension cord. A polarized

extension cord will require the use of a

polarized wall outlet. This plug will ﬁt into

the polarized wall outlet only one way. If the

plug does not ﬁt fully into the wall outlet,

reverse the plug. If the plug still does not

ﬁt, contact a qualiﬁed electrician to install

the proper wall outlet. Do not change the

equipment plug, extension cord receptacle,

or extension cord plug in any way.

2. FOR ALL APPLIANCES

a) Avoid dangerous environment. Don’t use

appliances in damp or wet locations.

b) Don’t use in rain.

c) Keep children away. All visitors should be

kept at a distance from work area.

d) Dress properly. Do not wear loose clothing

or jewelry. They can be caught in moving

parts. Use of protective gloves and

substantial footwear is recommended

when working outdoors. Wear protective

hair covering to contain long hair.

e) Use safety glasses. Always use face or dust

mask if operation is dusty.

f) Use right appliance. Do not use appliance

for any job except that for which it is

intended.

g) Ground Fault Circuit Interrupter (GFCI)

protection should be provided on the

circuit(s) or outlet(s) to be used for the

gardening appliance. Receptacles are

available having built-in GFCI protection

and may be used for an added measure of

safety.

h) WARNING! To reduce the risk of

electric shock, use only with an

extension cord intended for outdoor use,

such as an extension cord of cord type

SW-A, SOW-A, STW-A, STOW-A, SJW-A,

SJOW-A, SJTW-A. or SJTOW-A.

i) Extension cord! Make sure your extension

cord is in good condition. When using an

extension cord, be sure to use one heavy

enough to carry the current your product

will draw. An undersized extension cord

will cause a drop in line voltage resulting

in loss of power and overheating. Table 1

shows the correct size to use depending on

cord length and nameplate ampere rating.

If in doubt, use the next heavier gage. The

smaller the gage number, the heavier the

cord. To reduce the risk of disconnection

of appliance cord from the extension cord

during operating:

i) Make a knot as shown in Figure 2

ii) Use one of the plug-receptacle retaining

straps or connectors described in this

manual.

Table 1 Minimum gauge for extension

cords

Volts Total length of cord in feet

120V

25 50 100 150

240V 50 100 200 300

Ampere Rating More

than Not more than

AWG

0-6 18 16 16 12

0-7 18 16 14 12

0-8 16 16 16 12

0-9 14 12 Not recommended

NOTE-Only the applicable parts of the Table need to

be included. For instance, a 120-volt product need not

include the240-volt heading.

Trilingual-WG102-M-060609.indd 7 2006-6-9 16:56:27

Grass/Edge trimmer ENG

Figure 2 Method of securing extension

cord

(A) tie cord as show

(B) connect plug and receptacle

j) Avoid unintentional starting. Don’t carry

plugged-in appliance with ﬁnger on switch.

Be sure switch is off when plugging in.

k) Don’t abuse cord. Never carry appliance

by cord or yank it to disconnect from

receptacle. Keep cord from heat, oil, and

sharp edges.

l) Don’t grasp the exposed cutting blades or

cutting edges when picking up or holding

the appliance.

m) Don’t force appliance. It will do the job

better and with less risk of injury at the rate

for which it was designed.

n) Don’t overreach. Keep proper footing and

balance at all times.

o) Stay alert. Watch what you are doing. Use

common sense. Do not operate appliance

when you are tired.

p) Disconnect appliance. Disconnect the

appliance from the power supply when not

in use, before servicing, when changing

accessories such as blades, and the like.

q) Store idle appliances indoors. When not in

use, appliances should be stored indoors

in dry, and high or locked-up place, out of

reach of children.

r) Maintain appliance with care. Keep cutting

edge sharp and clean for best performance

and to reduce the risk of injury. Follow

instructions for lubricating and changing

accessories. Inspect appliance cord

periodically, and if damaged, have it

repaired by an authorized service facility.

Inspect extension cords periodically and

replace if damaged. Keep handles dry,

clean, and free from oil and grease.

s) Check damaged parts. Before further use

of the appliance, a guard or other part that

is damaged should be carefully checked

to determine that it will operate properly

and perform its intended function. Check

for alignment of moving parts, binding of

moving parts, breakage of parts, mounting,

and any other condition that may affect its

operation. A guard or other part that is

damaged should be properly repaired or

replaced by an authorized service center

unless indicated elsewhere in this manual.

3. EDGER-TRIMMERS

a) Keep guards in place and in working

order.

b) Keep blades sharp.

c) Keep hands and feet away from cutting

area.

4. CULTIVATORS, GRASS SHEARS

a) Keep hands away from blades.

Save these instructions.

CORD

SET

APPLIANCE CORD

0908

Trilingual-WG102-M-060609.indd 8 2006-6-9 16:56:27

Grass/Edge trimmer ENG

SYMBOLS

Read the manual

Warning

Wear eye protection

Wear ear protection

To avoid possibility of electric

shock, do not use in damp or wet

conditions.

Switch off! Remove plug from

power supply before adjusting,

cleaning or if cable is entangled or

damaged

Keep all other people, including

children, pets and bystanders

outside the 50 feet hazard zone, stop

the trimmer immediately if you are

approached.

OPERATING INSTRUCTIONS

CONNECTING THE MAIN HANDLE

ANDSHAFT (See A).

Turn the upper adjustment knob (3) clockwise

to loosen it. Insert telescopic shaft into the main

handle until it clicks into place (See A).Retighten

by turning anti-clockwise.

CONNECTING THE SAFETY GUARD

WARNING: NEVER USE THE

TRIMMER WITHOUT FITTING THE

GUARD.

Slide the safety guard onto the trimmer head

by using the trimmer head grooves (See B),

Secure the safety guard by using the screw

provided, located inside of the guard.

CONNECTING THE SPACER GUARD

Snap the Spacer Guard into the trimmer head

(See C), when not required, rotate the spacer

guard underneath the safety guard and clip into

place.

ADJUSTING THE HEIGHT (See D)

Unscrew the lower adjustment knob (4) extend

the telescopic shaft, then retighten.

ROTATING THE MAIN HANDLE (See E)

Unscrew the upper adjustment knob (3), rotate

the main handle 90 degrees clockwise, then

retighten.

ADJUSTING THE AUXILIARY HANDLE

(See F)

Rotate the handle release lever (5) anticlockwise,

then adjust the auxiliary handle (2) to desired

position, and then tight the lever clockwise

ADJUSTING THE TRIMMER HEAD ANGLE

Grip the trimmer head with one hand and

the shaft with the other. Change the angle by

applying adequate force. You will hear a heavy

click for each angle adjustment, which is part of

the ratchet mechanism. The clicking sound is

normal and is not a defect of the tool (See G).

ON/OFF TRIGGER

Press and hold the trigger to operate the

trimmer. Release to stop

Warning: The cutting head continues to

0908

Trilingual-WG102-M-060609.indd 9 2006-6-9 16:56:28

Grass/Edge trimmer ENG

rotate after the trimmer has been switched off.

Wait until it stops before laying the trimmer

down.

OPERATION

Warning: Always wear eye protection

and heavy clothing to prevent rocks and

debris from hitting you and causing an eye

injury or other serious injuries. Use two hands

operate the trimmer and hold the unit below

waist level. To best ensure that debris is thrown

away from your body, work only from the right

to left. For optimal trimming and edging results.

While maintaining comfort, keep the trimmer

head parallel to the ground when trimming

(perpendicular, when edging). When trimming

be sure to keep sufﬁcient distance between the

cutting line and the ground.

Warning: Before operating, make

sure both trimmer lines are extended.

When trimming, make sure motor is

running at full speed.

Warning: Use only 0.065” (1.65mm)

diameter cutting line. Other line sizes

will not properly feed in the trimmer head

and could cause serious injury. Never use

other materials such as wires, string or

rope, as this may break off during cutting

and cause serious injury.

TRIMMING

Hold the bottom of the trimmer head about 3

inches above the ground and at an angle. Allow

only

the tip of line to make contact. Do not force

trimmer line into work area.

EDGING (See H)

Unscrew the upper adjustment knob (3), rotate

the main and auxiliary handle 90º, and retighten

the knob. Adjust trimmer head angle so that it is

in line with the shaft (horizontal). Put the wheel

on the ground to begin edging, using the white

line guides to indicate the cutting position at the

edge of your lawn. While edging, allow the tip

of the line to make contact. Do not force the line.

The wheel helps prevent the unit from touching

the ground. Take extra caution while edging as

objects can be thrown from the trimmer line.

AUTOMATIC LINE FEED SYSTEM

When initially switching on the trimmer, a small

length of line is fed out. A ‘clattering’ noise will

be heard for a short time. This is normal and is

caused by the line being cut by the line cutter.

Once the line is cut to the correct length, the

‘clattering’ noise will stop and the trimmer

motor will run at full speed. To feed more line,

stop the trimmer completely, then restart,

allowing the motor to reach full speed. Repeat

this until you hear the ‘clattering’ noise of the

line cutting. (Do not repeat this procedure more

than 6 times)

REMOVING THE CAP TO MANUALLY FEED

THE LINE (See I)

Press and release manual line feed button

(16), whilst gently pull out the lines until

the lines reaches the line cutter. When the

required amount of line is fed out, gently pull

on the second line (there is no need to press

the manual line feed button again). If the line

extends past the line cutter, too much line has

been fed out. If too much line is fed out, remove

the spool cap and click the spool anti-clockwise

until the line is at the desired length.

REMOVING THE CAP

Press and hold in the two latches (12) (See

J).Pull cap away from the spool holder. Keep

the cap and spool holder clean from debris. To

replace the cap, press it ﬁrmly towards the spool

holder. Ensure that it is correctly connected by

trying to remove it without depressing the two

latches.

CHANGING THE LINE SPOOL:

First take off the cap and remove the old spool.

Place the new spool into the cap and make sure

the spool is in line with the trimmer’s eyelets.

Feed one line through the eyelet, then repeat

for second line. Reattach the cap.

Warning! Your Trimmer is designed to

only use line with a maximum diameter

of 0.065”.Only use nylon line.

1110

Trilingual-WG102-M-060609.indd 10 2006-6-9 16:56:29

Grass/Edge trimmer ENG

parts free of charge, repair products subject

to fair wear and tear, free of charge, or at our

discretion, replace the unit free of charge

to ensure minimum inconvenience to the

customer. Your warranty is subject to the

following conditions:

• Proof of purchase date and a valid receipt is

produced.

• The product has not been misused.

• The product has not been used for Professional

purposes.

• Unauthorized persons have not attempted

repairs.

• The product has not been used for hire

purposes.

• The product has not sustained damage through

foreign objects, substances or accidents.

• Damage is not a result of ﬁtting non-approved

accessories.

To claim the guarantee, you will need to submit

proof of purchase to the seller or an authorized

repair agent. You can check the location of your

nearest authorized repair agent by contacting

us at:

Positec USA, Inc.

Charlotte, NC 28216

PHONE: 1-866-354-WORX (9679)

This warranty does not apply to accessories.

This warranty applies only to the original

purchaser and may not be transferred.

All repairs and replacement tools will be

covered by the limited warranty for the balance

of the warranty period from the date of the

original purchase.

All repairs must use genuine spare parts.

IMPORTANT - Always wind the line onto the

upper section of the spool ﬁrst.

TO MANUALLY WIND LINE

Take approximately 16ft line and insert 5/8” of

line into one of the holes in the upper section

of the spool. Wind the line in the direction of

the arrows on the top of the spool. Leave

approximately 4” of line unwound and place it

into the cleat. Repeat on the lower section of

spool. Care should be taken to ensure that the

line is neatly coiled on the spool. Failure to do

so will impair the efﬁciency of the automatic

line feed. Then ﬁt the spool as described above

in “Changing the Line Spool”.

MAINTENANCE

After use, disconnect the machine from the

power supply and check for damage.

Your power tool requires no additional

lubrication or maintenance.

There are no user serviceable parts in your

power tool.

Electric trimmers should only be repaired by an

authorised repairer.

Use only manufacturers recommended

replacement parts and accessories.

Never use water or chemical cleaners to clean

your power tool. Wipe clean with a dry cloth.

Always store your power tool in a dry place out

of the reach of children.

Keep the motor ventilation slots clean. Keep all

working controls free of dust.

If you see some sparks ﬂashing in the ventilation

slots, this is normal and will not damage your

power tool.

WARRANTY STATEMENT

30 DAY Satisfaction Guarantee

If your WORX product becomes defective due

to faulty materials or workmanship within the

speciﬁed warranty period of;

• 24 months for DIY and light trade use, from

the date of purchase.

We guarantee to repair or replace all defective

1110

Trilingual-WG102-M-060609.indd 11 2006-6-9 16:56:29

Page is loading ...

Trilingual-WG102-M-060609.indd 26 2006-6-9 16:56:40

Trilingual-WG102-M-060609.indd 27 2006-6-9 16:56:40

Designed in Italy. Made in China

Conçu en Italie. Fabriqué en Chine

Diseñado en Italia. Fabricado en China

Trilingual-WG102-M-060609.indd 28 2006-6-9 16:56:40

WORX Tools Trimmer WG102 User manual

Brand: WORX Tools

Model: Trimmer WG102

Category: Grass trimmers

Type: User manual

This manual is also suitable for

WG102

Download PDF

report

in other languages

français: WORX Tools Trimmer WG102 Manuel utilisateur
español: WORX Tools Trimmer WG102 Manual de usuario

WORX Tools Trimmer WG102 User manual

This manual is also suitable for

WORX Tools Trimmer WG102 User manual

in other languages

Related papers

Other documents