GE AKV08FB Owner's manual

Brand: GE

Model: AKV08FB

Category: Mobile air conditioners

Type: Owner's manual

AKL08
AKN08
AKQ08
AKV08
AKW08
Safety Instructions  . . . . . . . .2, 3
Operating Instructions
Control Knob Models  . . . . . .6, 7
Touch Pad Models . . . . . . . . .4, 5
Care and Cleaning
Air Filter  . . . . . . . . . . . . . . . . . .8
Grille and Case  . . . . . . . . . . . . .8
Outdoor Coils . . . . . . . . . . . . . .8
Installation Instructions
Through-the-Wall
Installation—Optional . . . . . . .18
Window Installation . . . . . . .9–17
Troubleshooting Tips  . . . .19, 20
Normal Operating Sounds  . . .20
Consumer Support
Consumer Support  . . . . . . . . .24
Product Registration  . . . . .21, 22
Warranty  . . . . . . . . . . . . . . . . .23
49-7453-1 12-02 JR
Owner’s Manual and
Installation Instructions
Write the model and serial numbers here:
Model # __________________________
Serial # __________________________
Find these numbers on a label on the
side of the air conditioner.
Air Conditioners
Room
www.GEAppliances.com

IMPORTANT SAFETY INFORMATION.

READ ALL INSTRUCTIONS BEFORE USING.

WARNING!

For your safety, the information in this manual must be followed to minimize the risk of fire, electric shock

or personal injury.

■ Use this appliance only for its intended

purpose as described in this Owner’s

Manual.

■ This air conditioner must be properly

installed in accordance with the Installation

Instructions before it is used.

■ Never unplug your air conditioner by

pulling on the power cord. Always grip

plug firmly and pull straight out from the

receptacle.

■ Repair or replace immediately all electric

service cords that have become frayed or

otherwise damaged. Do not use a cord

that shows cracks or abrasion damage

along its length or at either the plug or

connector end.

■ Turn the mode control to OFF and unplug

your air conditioner before making any

repairs or cleaning.

■ NOTE: We strongly recommend that any

servicing be performed by a qualified individual.

■ For your safety…do not store or use

combustible materials, gasoline or other

flammable vapors or liquids in the vicinity

of this or any other appliance.

■ All air conditioners contain refrigerants,

which under federal law must be removed

prior to product disposal. If you are getting

rid of an old product with refrigerants, check

with the company handling disposal about

what to do.

SAFETY PRECAUTIONS

Do not, under any circumstances, cut or remove

the third (ground) prong from the power cord. For

personal safety, this appliance must be properly

grounded.

The power cord of this appliance is equipped

with a 3-prong (grounding) plug which mates

with a standard 3-prong (grounding) wall

outlet to minimize the possibility of electric

shock hazard from this appliance.

Have the wall outlet and circuit checked by a

qualified electrician to make sure the outlet is

properly grounded.

Where a 2-prong wall outlet is encountered,

it is your personal responsibility and obligation

to have it replaced with a properly grounded

3-prong wall outlet.

The air conditioner should always be

plugged into its own individual electrical

outlet which has a voltage rating that matches

the rating plate.

This provides the best performance and also

prevents overloading house wiring circuits

which could cause a fire hazard from

overheated wires.

See the Installation Instructions, Electrical

Requirements section for specific electrical

connection requirements.

HOW TO CONNECT ELECTRICITY

Consumer Support

Troubleshooting Tips Operating Instructions Safety InstructionsInstallation Instructions

Consumer SupportTroubleshooting TipsOperating InstructionsSafety Instructions Installation Instructions

WARNING!

Because of potential safety hazards under certain

conditions, we strongly recommend against the

use of an extension cord.

However, if you must use an extension cord,

it is absolutely necessary that it be a UL-listed,

14 gauge, 3-wire grounding type appliance

extension cord having a grounding type plug

and outlet and that the electrical rating of the

cord be 15 amperes (minimum) and 125 volts.

CAUTION:

DO NOT use an extension cord with any of the

230/208 volt models.

USE OF EXTENSION CORDS—115-Volt models only

Because of potential safety hazards under certain

conditions, we strongly recommend against the

use of an adapter plug.

However, if you must use an adapter, where

local codes permit, a temporary connection may

be made to a properly grounded 2-prong wall

outlet by use of a UL-listed adapter available

at most local hardware stores.

The larger slot in the adapter must be aligned

with the larger slot in the wall outlet to provide

proper polarity in the connection of the

power cord.

When disconnecting the power cord from the

adapter, always hold the adapter in place with

one hand while pulling the power cord plug

with the other hand. If this is not done, the

adapter ground terminal is very likely to break

with repeated use.

If the adapter ground terminal breaks, DO NOT

USE the air conditioner until a proper ground

has been established.

Attaching the adapter ground terminal to a wall outlet

cover screw does not ground the appliance unless the

cover screw is metal, and not insulated, and the wall

outlet is grounded through the house wiring. You should

have the circuit checked by a qualified electrician to

make sure the outlet is properly grounded.

USE OF ADAPTER PLUGS—115-Volt models only

www.GEAppliances.com

SAVE THESE INSTRUCTIONS

READ AND FOLLOW THIS SAFETY INFORMATION CAREFULLY.

About the controls on the air conditioner—models with touch pads.

Features and appearance will vary.

Consumer Support

Troubleshooting Tips Operating Instructions Safety InstructionsInstallation Instructions

■ To ensure proper operation, aim the remote

control at the signal receiver on the air

conditioner.

■ The remote control signal has a range of

up to 21 feet.

■ Make sure nothing is between the air conditioner

and the remote control that could block the

signal.

■ Make sure batteries are fresh and installed

correctly as indicated on the remote control.

Controls

ON/OFF Pad

Turns air conditioner on and off.

MODE

Use to set the air conditioner to COOL or

FAN mode.

Increase ▲ /Decrease ▼ Pads

Use to set temperature when in COOL mode.

FAN Pad

Use to set the fan speed to LOW, MED

or HIGH.

TIMER Pad

ON—When the air conditioner is off,

it can be set to automatically turn on in

1 to 12 hours at its previous setting. Each

touch will set the timer in hours.

OFF—When the air conditioner is on,

it can be set to automatically turn off in

1 to 12 hours. Each touch will set the timer

in hours.

To cancel the timer, press the TIMER pad

until the display time disappears.

NOTE: All timer settings are automatically

cancelled if the unit is turned on or off after

setting the timer.

Display

Shows the room temperature, set

temperature or the time remaining on the

timer. After setting the controls, the display

will change to show the room temperature.

To recall the set temperature to the display,

press the Increase ▲ / Decrease ▼ pad once.

To recall the time remaining on the timer,

if it was set, press the TIMER pad once.

Display Codes

E1—Automatic filter clean reminder.

Turn the air conditioner OFF and unplug it.

NOTE: The air conditioner must be unplugged

for the automatic filter clean timer to reset.

Clean the filter. See the Care and Cleaning

section. After cleaning, replace the filter

and plug the air conditioner back in.

Er—Room temperature sensor failure.

Call for service.

Remote Control Signal Receiver

Remote Control

Air Conditioner Controls Remote Control

Cool on

Fan on

High fan on

Medium fan on

Low fan on

Consumer SupportTroubleshooting TipsOperating InstructionsSafety Instructions Installation Instructions

www.GEAppliances.com

When the air conditioner is turned on, it will

automatically start in the setting last used,

except the timer will be cancelled if it was set.

Lights in the display or beside the touch pads

on the air conditioner control panel indicate the

selected settings.

Use the COOL mode with HIGH, MED or LOW fan

for cooling. Use the Increase ▲ / Decrease ▼ pads

to set the desired temperature between 60°F and

90°F in 2°F increments (or between 16°C and

31°C in 1°C increments if the control has been

set to use Celsius).

A thermostat is used to maintain the room

temperature. The compressor will cycle on and off

to keep the room at the set level of comfort. Set the

thermostat at a lower number and the indoor air

will become cooler. Set the thermostat at a higher

number and the indoor air will become warmer.

NOTE: If the air conditioner is off and is then turned on while

set to COOL, it will take approximately 3 minutes for the

compressor to start and cooling to begin.

Cooling Descriptions

For Normal Cooling—Select the COOL mode and

HIGH or MED fan with a middle set temperature.

For Maximum Cooling—Select the COOL mode

and HIGH fan with a lower set temperature.

For Quieter & Nighttime Cooling—Select the

COOL mode and LOW fan with a middle set

temperature.

NOTE: If you switch from a COOL setting to OFF or to

a fan setting, wait at least 3 minutes before switching back

to a COOL setting.

COOL Mode

Use the FAN at HIGH, MED or LOW to provide

air circulation and filtering without cooling.

Since fan only settings do not provide cooling,

a temperature setting will not be displayed.

Your control is set to use and display Fahrenheit temperature

selections, but you may change it to use and display Celsius

selections.

Press and hold the Increase ▲ / Decrease ▼ pads

at the same time to switch to ˚C or ˚F as desired.

FAN Mode Fahrenheit or Celsius

The vent control is located on the inside of the

air louvers at the bottom of the vent.

When set at CLOSE, only the air inside the room

will be circulated and conditioned. When set at

OPEN, some inside air is exhausted outside.

Vent Control

Up and Down

Fingertip pressure on the horizontal louvers

adjusts the air direction up or down.

Side-to-Side

The side-to-side air direction is adjusted by moving

the air direction lever to the left or right.

Air Direction

To open the vent.

To close the vent.

Vent control

lever

Vent control

lever

Air direction

lever

About the controls on the air conditioner—models with control knobs.

Features and appearance will vary.

Consumer Support

Troubleshooting Tips Operating Instructions Safety InstructionsInstallation Instructions

Controls

Mode Controls

HIGH COOL, MED COOL and LOW COOL provide

cooling with different fan speeds.

COOL provides cooling with a fixed fan speed.

LOW FAN, HIGH FAN or FAN provides air

circulation and filtering without cooling.

NOTE: If you move the switch from a cool setting to

OFF or to a fan setting, wait at least 3 minutes before

switching back to a cool setting.

Cooling Descriptions

For Normal Cooling—Select HIGH COOL or

MED COOL with the temp control at midpoint.

For Maximum Cooling—Select HIGH COOL with

the temp control at the highest number

available on your knob.

For Quieter and Nighttime Cooling—Select

LOW COOL with the temp control at midpoint.

Temp Controls

The temp control is used to maintain the

room temperature. The compressor will cycle

on and off to keep the room at the same

level of comfort. When you turn the knob to

a higher number, the indoor air will become

cooler. Turn the knob to a lower number and

the indoor air will become warmer.

TEMP CONTROL

MODE CONTROLS

Your model will have one of the above type controls.

OFF

LOW

FAN

LOW

COOL

HIGH

FAN

HIGH

COOL

MED

COOL

OFF

FANCOOL

Consumer SupportTroubleshooting TipsOperating InstructionsSafety Instructions Installation Instructions

www.GEAppliances.com

Additional controls and important information.

The vent control is located on the inside of the

air louvers at the bottom of the vent.

When set at CLOSE, only the air inside the room

will be circulated and conditioned. When set

at OPEN, some inside air is exhausted

outside.

Vent Control

Fingertip pressure on the horizontal louvers adjusts

the air direction up or down.

Air Direction—Up and Down

The side-to-side air direction is adjusted by moving

the air direction lever to the left or right.

Air Direction—Side-to-Side

To open the vent. To close the vent.

Vent control

lever

Vent control

lever

Air direction

lever

Consumer Support

Troubleshooting Tips Operating Instructions Safety InstructionsInstallation Instructions

Care and cleaning of the air conditioner.

Turn the air conditioner off and remove the plug

from the wall outlet before cleaning.

To clean, use water and a mild detergent. Do not

use bleach or abrasives.

Grille and Case

The coils on the outdoor side of the air conditioner

should be checked regularly. If they are clogged

with dirt or soot, they may be professionally steam

cleaned, a service available through your GE

service outlet.

Outdoor Coils

The air filter behind the front grille should be

checked and cleaned at least every 30 days or

more often if necessary.

E1 in the display (on models with touch pads)

is an automatic filter clean reminder. Turn the

air conditioner OFF and unplug it.

NOTE: The air conditioner must be unplugged for the

automatic filter clean timer to reset.

Clean the filter with warm, soapy water. Rinse and

let the filter dry before replacing it.

NOTE: DO NOT rinse, or put the filter in an automatic

dishwasher.

CAUTION: DO NOT operate the air

conditioner without a filter because dirt and lint will clog it

and reduce performance.

To remove:

Pull to unlatch the lower corners of the inlet

grille and lift it up and off.

Using the tab, pull up slightly on the filter to

release it and pull it down to remove.

Air Filter

Consumer SupportTroubleshooting TipsOperating InstructionsSafety Instructions Installation Instructions

Preparing to install the air conditioner.

Read these instructions completely and carefully.

NOTE TO INSTALLER: Leave these instructions with

the air conditioner after installation is completed.

NOTE TO CONSUMER: Keep this Owner’s Manual

and Installation Instructions for future use.

IMPORTANT NOTES:

For personal safety, this air conditioner must be

properly grounded.

It is important to have the wall outlet and circuit

checked by a qualified electrician if there is any

doubt as to whether a proper ground exists.

Follow National Electrical Codes (NEC) and/or local

codes and ordinances.

CAUTION:

Do not, under any circumstances, cut or remove

the third (ground) prong from the power cord.

Do not change the plug on the power cord of this

air conditioner.

Aluminum house wiring may present special

problems

—

consult a qualified electrician.

Before You Begin

Some models require 115/120-volt a.c.,

60 Hz grounded outlet protected with a

15-amp time delay fuse or circuit breaker.

The 3-prong grounding plug minimizes the

possibility of electric shock hazard. If the wall outlet

you plan to use is only a 2-prong outlet, it is your

responsibility to have it replaced with a properly

grounded 3-prong wall outlet.

Some models require 230/208-volt a.c.,

protected with a time delay fuse or circuit

breaker. These models should be installed

on their own single branch circuit for best

performance and to prevent overloading

house or apartment wiring circuits, which

could cause a possible fire hazard from

overheating wires.

Electrical Requirements

■ Phillips-head screwdriver

■ Adjustable wrench

■ Ruler or tape measure

■ Drill

■ Scissors or knife

■ Pencil

■ Level

Tools You Will Need

Type A (17)

Support bracket (2)

Right

accordion

panel

Foam top

window gasket

Window sash seal

(thin, adhesive-backed)

Left

accordion

panel

Type B (11) Type C (6) Accordion panel

clamp (2)

Consumer Support

Troubleshooting Tips Operating Instructions Safety InstructionsInstallation Instructions

Window installation instructions.

Parts Included

Leveling bolt (2)

Nut (2)

Support rail (2)

Top mounting rail

seal strip

Bottom

mounting rail

Air conditioner case

Top mounting rail

Window locking

bracket

Window stool

seal (thick,

adhesive-backed)

Consumer SupportTroubleshooting TipsOperating InstructionsSafety Instructions Installation Instructions

Read completely, then follow step-by-step.

Window Requirements

■ These instructions are for a standard double-

hung window. You will need to modify them for

other types of windows.

■ The air conditioner can be installed without

the accordion panels if needed to fit in a narrow

window. See the window opening dimensions.

■ All supporting parts must be secured to firm

wood, masonry or metal.

■ The electrical outlet must be within reach of the

power cord.

15″ min.

21-3/4″ to 35-1/4″

(With accordion panels)

18″ min.

(Without accordion panels)

Storm Window Requirements

A storm window frame will not allow the air

conditioner to tilt towards the outside and

will keep it from draining properly. To adjust

for this, attach a piece of wood to the stool.

WOOD PIECES

—

WIDTH: 2″

LENGTH: Long enough to fit inside the window

frame.

THICKNESS: To determine the thickness, place a

piece of wood on the stool to make it 1/2″ higher

than the top of the storm window frame.

Attach securely with nails or screws provided by

the installer.

1/2″ higher

than frame

Storm window

frame

Wood

Stool

Remove the Air Conditioner From the Case

Remove and discard the 2 shipping screws

from the bottom rear of the case.

Pull to unlatch the lower corners of the inlet

grille and lift it up and off.

Consumer Support

Troubleshooting Tips Operating Instructions Safety InstructionsInstallation Instructions

Remove the Air Conditioner From the Case (cont.)

Using the tab, pull up slightly on the filter

to release it and pull it down to remove.

Remove the two grille frame screws.

Grasp the lower corners of the grille frame

while pressing in on the case sides with your

finger tips. Pull out to release and lift it up.

NOTE: Do not pull the

bottom edge toward

you more than 3 ″ or

you may damage the

tabs of the grille.

On some models, you must also disconnect

the control connectors before the grille frame

can be removed. Press the locking tabs in

while pulling on the other side to release.

Remove the two locking screws and locking

brackets from the lower front of the unit.

Remove the screw securing the ground wire

to the right side face of the unit.

Slide the air conditioner from the case by

gripping the base pan handle and pulling

forward while bracing the case.

Window installation instructions.

Screw

Ground wire

Press in

Pull

Press in

Grille frame screws

Consumer SupportTroubleshooting TipsOperating InstructionsSafety Instructions Installation Instructions

Remove the Shipping Pad

Remove and discard the shipping pad next to the compressor.

Install the Mounting Rails onto the Case

Remove the backing from the top mounting

rail seal strip and attach it to the bottom of

the top mounting rail.

Attach the top mounting rail onto the top

of the case with 5 Type A screws.

Attach the bottom mounting rail to the

bottom of the case from the inside, using

4 Type A screws.

Type A screws

Type A

screws

Type A screw

Remove and discard

shipping pad

Consumer Support

Troubleshooting Tips Operating Instructions Safety InstructionsInstallation Instructions

Install the Side Accordion Panels

Slide the left and right accordion panels into

the top and bottom mounting rails.

Attach the accordion panels to the case using

4 Type A screws on each side.

Window installation instructions.

Prepare the Window

Cut the window sash seal (thin, adhesive-

backed) to the window width and stick the

adhesive side to the bottom of the sash.

Mark the centerline of the stool. Measure and

mark the locations for the support assemblies

⁄8″ from both sides of the centerline.

Type A screws

Top mounting rail

Bottom mounting rail

Accordion panel

Window sash seal

⁄8″

Stool

⁄8″

Consumer SupportTroubleshooting TipsOperating InstructionsSafety Instructions Installation Instructions

Assemble the Supports

Loosely attach a support bracket to a support

rail using 2 Type C screws.

NOTE: The support bracket may be attached into

either slot in the support rail, depending on the depth

of your window sill.

Thread a nut onto a leveling bolt, then

thread the leveling bolt into the support

bracket. An adjustable wrench may be needed.

Before attaching the support, hold the neck of

the support rail against the back edge of the

window stool.

Adjust the position of the support bracket

inward or outward on the support rail until the

leveling bolt is near the outside edge of the sill.

NOTE: Make sure that the leveling bolt will be firmly

supported by the sill.

Tighten the Type C screws to secure the

support bracket to the support rail in the

correct position.

Repeat steps A–E to assemble the second

support.

Install the Supports

Line up the V-notches in the support rails with

the left and right marks on the stool. Make

sure that the support rail is against the back

of the stool and drill two 1/8″ pilot holes into

the stool through the holes in the head of the

support rail. Attach the supports to the stool

using two Type B screws in each support.

Adjust the leveling bolts against the sill so that

the supports have a slight tilt to the outside.

Use a level; about 1/2 bubble will be the

correct slant to the outside. After leveling is

done, tighten the leveling bolt nut.

NOTE: Use a steel washer between the leveling

bolts and the sill if the sill is weak.

Attach the adhesive side of the window stool seal

(thick, adhesive-backed) to the window stool.

Type C screws

Support bracket

Support rail

Support bracket

Leveling bolt

Nut

Adjust as

needed

Neck of

support rail

Stool

Supports

Sill

Type B

screws

Stool

1/2 bubble

Leveling bolt

Nut

Window stool seal

Consumer Support

Troubleshooting Tips Operating Instructions Safety InstructionsInstallation Instructions

Install the Case in the Window

Carefully position the case in the window

until the bottom mounting rail drops into the

channels in the supports. Center the case and

lower the window behind the top mounting

rail. The case should be slightly tilted to the

outside. Use a level; about a 1/2 bubble will

be the correct case slant to the outside.

Attach the bottom of the case to the support

rail with a Type C screw, one on each side.

Extend the left and right accordion panels

to the vertical window sashes, drill 1/8″ pilot

holes, and attach the top corners with 2 Type B

screws. Use an accordion panel clamp on each

lower corner to trap the panels. Drill 1/8″

pilot holes and attach the panel clamps with

Type B screws.

NOTE: Seal any openings around the case or accordion

panels with sealer or foam gaskets.

Window installation instructions.

Secure the Case in the Window and Install the Foam Top Window Gasket

Drill a 1/8″ pilot hole and attach the top

mounting rail to the sash with a Type B screw.

Cut the foam top window gasket to the

window width.

Stuff the foam between the glass and the

window to prevent air and insects from

getting into the room.

Attach the window locking bracket with

2 Type B screws.

Type B

screw

Type B

screw

Panel clamp and

Type B screw

Top mounting rail

Panel clamp and

Type B screw

Top mounting rail

Install the Air Conditioner in the Case

Slide the air conditioner into the case. Do not

push on the controls or the finned coils.

Make sure the air conditioner is firmly seated.

Reinstall the locking brackets and screws

removed earlier.

IMPORTANT! Reconnect the ground wire to

the air conditioner.

If your model has the control connectors,

reconnect them to the front grille by pressing

them together until the locking tabs snap

into place.

Attach the front grille frame to the case by

inserting the tabs on the grille frame into

the slots on the front top of the case. Push

the grille frame in until it snaps into place

around the power cord on the right side.

Secure the front grille frame to the case by

replacing the screws removed earlier.

Install the filter. Hook the inlet grille in the

frame and close it. Connect power.

Guide the levers carefully

through the grille frame

as you push it in.

Screw

Ground wire

Consumer SupportTroubleshooting TipsOperating InstructionsSafety Instructions Installation Instructions

Consumer Support

Troubleshooting Tips Operating Instructions Safety InstructionsInstallation Instructions

IMPORTANT

Through-the-wall installation is not appropriate if any

of the side louvers in the case will be obstructed by

the wall.

All side louvers in the case must project on the outdoor

side of the wall.

The room side of the case must project into the room

at least 1

⁄4″ from the finished wall.

The case must be installed level from side-to-side

and with a slight tilt from front to rear. Use a level;

about a 1/2 bubble will be the correct case slant to

the outside.

Remove the air conditioner from the case.

For specific instruction, refer to the Window

Installation Instructions.

Make certain a wall receptacle is available close

to the hole location or make arrangements to

install a receptacle.

Place the case in the wall opening and

secure with 12 1″ long #10 wood screws.

NOTE: Drill pilot holes, if necessary, for proper

installation. If the frame is oversized, use shims

to prevent case distortion.

Through-the-wall installation instructions—optional.

Finish the Wall Opening

Caulk all four sides on the outdoor side of the case to prevent moisture from getting through to the

interior wall. Use of flashing (drip rail) will further prevent water from dripping inside the wall and

down the outside of the building.

Caulking

Air louvers

(must project on

the outdoor side

of the wall)

Wood filler and caulking

(above and below the

flashing)

Flashing (drip rail)

⁄4″ min.

Bottom rail

Plaster line

Trim molding

(if desired)

Lintel angle

(if required)

Problem Possible Causes What To Do

Air conditioner The air conditioner • Make sure the air conditioner plug is pushed completely

does not start is unplugged. into the outlet.

The fuse is blown/circuit • Check the house fuse/circuit breaker box and replace

breaker is tripped. the fuse or reset the breaker.

Power failure. • On models with control knobs, if a power failure occurs,

turn the air conditioner OFF. When power is restored,

wait 3 minutes to restart the air conditioner to prevent

tripping of the compressor overload.

Air conditioner has Power interruption or • On models with touch pads, when the power is restored,

stopped running power failure occurred. wait 3 minutes to restart the air conditioner to prevent

tripping of the compressor overload. Press the POWER

pad and reset the controls to the desired settings.

Air conditioner does not Airflow is restricted. • Make sure there are no curtains, blinds or furniture

cool as it should blocking the front of the air conditioner.

The temp control may not • On models with touch pads: in COOL mode, press the

be set correctly. Decrease ▼pad.

• On models with control knobs, turn the temperature

knob to a higher number.

The air filter is dirty. • Clean the filter at least every 30 days.

See the Operating Instructions section.

The room may have been hot. • When the air conditioner is first turned on, you need to

allow time for the room to cool down.

Cold air is escaping. • Check for open furnace floor registers and cold air

returns.

• Set the air conditioner’s vent to the closed position.

Cooling coils have iced up. • See “Air conditioner freezing up” below.

Air conditioner Ice blocks the air flow and • On models with control knobs, set the mode control at

freezing up stops the air conditioner HIGH FAN or HIGH COOL with the temp at 1 or 2.

from cooling the room.

• On models with touch pads, set the controls at HIGH FAN

or HIGH COOL and set the thermostat to a higher

temperature.

The remote control The batteries are inserted • Check the position of the batteries. They should be

is not working incorrectly. inserted in the opposite (+) and (–) direction.

The batteries may be dead. • Replace the batteries.

Water drips outside Hot and humid weather. • This is normal.

Water drips indoors The air conditioner is not • For proper water disposal, make sure the air conditioner

tilted to the outside. slants slightly from the case front to the rear.

Water collects in Moisture removed from air • This is normal for a short period in areas with little

base pan and drains into base pan. humidity; normal for a longer period in very humid areas.

Before you call for service… www.GEAppliances.com

Troubleshooting Tips.

Save time and money! Review the chart below first and

you may not need to call for service.

Consumer SupportTroubleshooting TipsOperating InstructionsSafety Instructions Installation Instructions

Consumer Support

Troubleshooting Tips Operating Instructions Safety InstructionsInstallation Instructions

Problem Possible Causes What To Do

Temperature settings The control has been • Press and hold the Increase ▲ / Decrease ▼ pads at the

in the display can only set to use Celsius. same time to switch to Fahrenheit settings.

be set between 16 and 31

“E1” appears Filter needs to be cleaned. • Turn the air conditioner OFF and unplug it.

in the display NOTE: The air conditioner must be unplugged for the

automatic filter clean timer to reset. Clean the filter.

See the Care and Cleaning section. After cleaning,

replace the filter and plug the air conditioner back in.

“Ed” appears Frost protect automatically • Turn the air conditioner off. Wait at least 3 minutes and

in the display activated. turn the air conditioner back on. If the code reappears,

call for service.

“En” appears Pipe temperature sensor • Call for service.

in the display failure.

“Er” appears Room temperature sensor • Call for service.

in the display failure.

Before you call for service…

Troubleshooting Tips.

■ You may hear a pinging noise caused by water

being picked up and thrown against the

condenser on rainy days or when the humidity

is high. This design feature helps remove

moisture and improve efficiency.

■ You may hear the thermostat click when the

compressor cycles on and off.

■ Water will collect in the base pan during high

humidity or on rainy days. The water may

overflow and drip from the outdoor side of

the unit.

■ The fan may run even when the compressor

does not.

Normal Operating Sounds

Page is loading ...

GE AKV08FB Owner's manual

Brand: GE

Model: AKV08FB

Category: Mobile air conditioners

Type: Owner's manual

Download PDF

report

in other languages

español: GE AKV08FB El manual del propietario

GE AKV08FB Owner's manual

GE AKV08FB Owner's manual

in other languages

Related papers

Other documents