Panasonic DP1510 Operating instructions

DP-2010E

with Options

DP-1810P

with Options

Digital Imaging Systems

Before operating this equipment, please read these instructions completely and keep these operating

instructions for future reference.

Getting To Know Your

Machine

J

?

I

Before StartingMaking CopiesOptionsOthers

Model No. DP-1510P/1810P/2010E

Operating Instructions

(For Copier)

English

P01_1810_2010_GAP(gbr).p65 5/27/02, 4:59 PM1

2

IMPORTANT INFORMATION

When requesting information, supplies or service always refer to the model and serial number of your

machine. The model and serial number plate (Main Name Plate) is located on the rear side of machine.

For your convenience, space is provided below to record information you may need in the future.

Model No.

Serial No.

Date of Purchase

Dealer

Address

Telephone Number

()

Supplies Telephone Number

()

Service Telephone Number

()

Model and Serial Number

Copyright  2002 by Matsushita Graphic Communication Systems, Inc.

The contents of these Operating Instructions are subject to change without notice.

(Digital copier with ADF option)

P02-03_1810_2010_GAP(gbr).p65 5/27/02, 4:59 PM2

3

Operation Chart

Common Features and Usage

■■

■ Basic Operation

Original

1

Place the

Original

2

Original Size

(Reduction/

Enlargement

Only)

3

Copy Size

(Reduction/

Enlargement

Only)

4

Number

of Copies

5

Press

START

■■

■ Position of the Original

Load Paper

Turn the Power

Switch On

C Place originals face down on the

platen or face up on the ADF.

C If the original is not positioned

properly, a portion of the original

may not be copied.

C For originals smaller than A5 size,

position the original within the area

of A5 and select A5.

■■

■ Commonly Used Functions and Operating Procedures

Full Size

Makes a copy that is the same

size as the original

145

Reduction or Enlargement

Copies the original at a fixed

reduction or enlargement ratio

13425

■■

■ Memory Capacity

When the memory becomes full during original scanning, the message “OUT OF MEMORY”

“CONTINUE? 1: YES 2: NO” will be displayed in the message display. In this case, follow the

operating instruction in the message display.

When additional memory is required, consult with an authorised servicing dealer.

(See page 12)

(See page 13)

Getting To Know Your

Machine

A5

A4

B4FLS

A3

B4

FLS2

FLS1

A5

A4

A5

A5 R

A4 R

FLS·B4

A3

A4

Original Guide

Original Guides

Adjust to the original’s width

ADF Tray

From PlatenFrom ADF (or i-ADF)

P02-03_1810_2010_GAP(gbr).p65 5/27/02, 4:59 PM3

4

Energy Star

As an ENERGY STAR

®

Partner, Panasonic has determined that this product meets the

ENERGY STAR

®

guidelines for energy efficiency.

This voluntary program specifies certain energy consumption and usage standards. This

product will automatically “power down” after a specified period of non-use. The use of this

ENERGY STAR

®

compliant product will reduce energy consumption and ultimately benefit the

environment.

The default functions can be adjusted depending on your office requirements.

Please ask your authorised Panasonic dealer for more details.

P04-05_1810_2010_GAP(gbr).p65 5/27/02, 4:59 PM4

5

Table of Contents

Getting To Know Your Machine

Operation Chart .............................................................................................................................. 3

■ Common Features and Usage ..............................................................3

Before Starting

Precautions ..................................................................................................................................... 7

Control Panel ................................................................................................................................10

Making Copies

Basic Copy .................................................................................................................................... 12

■ Full Size Copying ................................................................................ 12

■ Reduction or Enlargement Copying .................................................... 13

■ Zoom Copying .................................................................................... 14

■ Using the Sheet Bypass ..................................................................... 15

Creative Features ......................................................................................................................... 16

■ 2 in 1 Copy ......................................................................................... 16

■ 2 Page Copy ....................................................................................... 17

■ Book/Edge/Margin .............................................................................. 18

■ 2-Sided/1-Sided Copy ......................................................................... 19

■ 1 \ 2/2 \ 1/2 \ 2 Copy.................................................................... 20

■ Book \ 2 Copy .................................................................................. 21

■ Job Memory ....................................................................................... 22

■ Sort Copy ........................................................................................... 23

Other Features .............................................................................................................................. 24

■ Energy Saver/Interrupt Mode .............................................................. 24

■ Skyshot Mode..................................................................................... 25

Combined Function Table ............................................................................................................ 27

Function ........................................................................................................................................ 28

■ Checking the Copier’s Total Counter ................................................... 28

■ General Functions .............................................................................. 29

■ Copier Settings ................................................................................... 30

■ General Functions for Key Operator ................................................... 31

■ Copier Settings for Key Operator ........................................................ 32

■ Function Setting.................................................................................. 33

■ Function Setting for Key Operator ....................................................... 34

■ For Your Safety ..................................................................................... 7

■ Handling ...............................................................................................8

■ Toner and Paper ................................................................................... 8

■ Ventilation ............................................................................................. 8

■ Installation ............................................................................................ 9

Table of Contents

Energy Star ..................................................................................................................................... 4

P04-05_1810_2010_GAP(gbr).p65 5/27/02, 4:59 PM5

6

Table of Contents

Options

Accessories .................................................................................................................................. 39

■ Components ....................................................................................... 39

■ Automatic Document Feeder .............................................................. 40

Problem Solving

Problem Solving ........................................................................................................................... 42

■ Adding Paper (J) ............................................................................... 42

■ Adding the Toner and Replacing Waste Toner Container (?) ............. 43

■ Removing a Misfed Paper ................................................................... 45

Troubleshooting ........................................................................................................................... 52

■ Before Calling Service ........................................................................ 52

■ User Error Codes (U Code) ................................................................ 54

Others

Specifications ............................................................................................................................... 55

Options and Supplies ................................................................................................................... 57

P06-07_1810_2010_GAP(gbr).p65 5/27/02, 4:59 PM6

7

Precautions

For Your Safety

■■

■ Laser Safety

LASER SAFETY

This unit employs a laser. Only qualified service personnel should

attempt to service this device due to possible eye injury.

CAUTION:

USE OF CONTROLS, ADJUSTMENTS OR PERFORMANCE

PROCEDURES OTHER THAN THOSE SPECIFIED HEREIN MAY

RESULT IN HAZARDOUS RADIATION EXPOSURE.

■■

■ Caution Label

Before Starting

(Digital copier with ADF option)

P06-07_1810_2010_GAP(gbr).p65 5/28/02, 3:53 PM7

8

Precautions

Handling

■ Do not look directly at the exposure lamp when

copying.

■ Do not turn the power switch Off or open the front

panel during copying.

C Do not drop paper clips or other metal objects into

the copier.

Toner and Paper

■ Store toner, drum and paper in cool areas with low

humidity.

C Use high quality 60 - 90 g/m

2

(Sheet Bypass:

56 - 128 g/m

2

) paper.

C For optimum performance, it is recommended that

only Panasonic Brand supplies are used in the

copier.

Ventilation

■ The copier should not be installed in areas with the

following conditions:

C Extremely high or low temperature and humidity.

Ambient conditions

Temperature: 10 – 30°C

Relative humidity: 30 – 80%

C Where temperature and humidity can change

rapidly, causing condensation.

C Direct exposure to sunlight.

C Directly in the air conditioning flow.

C In areas of high dust concentration.

C In areas of poor ventilation.

C In areas with chemical fume concentration.

C In areas with extreme vibration.

C With unstable or uneven conditions (floors, etc.).

■ The copier should be installed in a well-ventilated

area to minimise the ozone density in the air.

P08-09_1810_2010_GAP(gbr).p65 9/17/03, 9:29 AM8

9

Installation

Precautions

Before Starting

■ The maximum power consumption is 1.2 kW.

A properly wired (grounded), dedicated, 6A, 220-240 V AC outlet is required.

Do not use an extension cord.

The power cord on this equipment must be used to disconnect the main power.

Please ensure that the socket outlet is installed near the equipment and is easily accessible.

FOR YOUR SAFETY

Caution Note: Disconnect from the mains supply before removing covers.

The mains plug on this equipment must be used to disconnect mains power. Please ensure that the

socket outlet is installed near the equipment and shall be easily accessible.

This appliance is supplied with a moulded three pin mains plug for your safety and convenience.

A 13 amp fuse is fitted in this plug.

Should the fuse need to be replaced please ensure that the replacement fuse has a rating of 13

amps and that it is approved by ASTA or BSI to BS1362

Check for the ASTA mark 7 or the BSI mark 6 on the body of the fuse.

If the plug contains a removable fuse cover you must ensure that it is refitted when the fuse is

replaced.

If you lose the fuse cover the plug must not be used until a replacement cover is obtained.

A replacement fuse cover can be purchased from your local Panasonic Dealer.

IF THE FITTED MOULDED PLUG IS UNSUITABLE FOR THE SOCKET OUTLET IN YOUR OFFICE

THEN THE FUSE SHOULD BE REMOVED AND THE PLUG CUT OFF AND DISPOSED OF SAFELY.

THERE IS A DANGER OF SEVERE ELECTRICAL SHOCK IF THE CUT OFF PLUG IS INSERTED

INTO ANY 13 AMP SOCKET.

If a new plug is to be fitted please observe the wiring code as shown below.

If in any doubt please consult a qualified electrician.

WARNING: THIS APPLIANCE MUST BE EARTHED.

IMPORTANT: The wires in this mains lead are coloured in accordance with the following code:

Green and Yellow: Earth

Blue : Neutral

Brown : Live

As the colours of the wires in the main lead of this appliance may not correspond with the coloured

markings identifying the terminals in your plug, proceed as follows:

The wire which is coloured GREEN-AND-YELLOW must be connected to the terminal in the plug which

is marked by letter E or by the safety Earth symbol “L” or coloured GREEN or GREEN-AND-YELLOW.

The wire which is coloured BLUE must be connected to the terminal in the plug which is marked

with the letter N or coloured BLACK.

The wire which is coloured BROWN must be connected to the terminal in

the plug which is marked with the letter L or coloured RED.

How to replace the fuse.

Open the fuse compartment with a screwdriver and replace the fuse.

For U.K.

N

P08-09_1810_2010_GAP(gbr).p65 6/7/02, 10:23 PM9

10

No Contents Refer to

#

2 in 1 Key

C From two 1-sided originals, side by side, to 1-sided copies.

Page 16

$

2 Page Copy Key

C Copying two facing pages on a A3 size original on two separate A4 size

sheets.

Page 17

%

Sort Key

C When using Electric Sorting Mode. Optional memory is required.

Page 23

& MARGIN Key C Shifts the image to the right or left. Page 18

( EDGE Key C Creates a blank edge. Page 18

) BOOK Key C Eliminates dark inner binding shadows. Page 18

*

Photo; Text/Photo; Text Keys

C Select the type of original(s) for image density adjustment.

PHOTO : Originals are mainly composed of photo.

TEXT/PHOTO: Combined originals with text and photo.

TEXT : Originals are mainly composed of text.

Page 12

+ Exposure Keys (DARKER, LIGHTER) Page 12

.

FUNCTION Key

C Use when changing the paper size, initial values for functions (default

values) and key operator settings.

Pages 28 – 37

- SET Key C Set the present selection. ——

Control Panel

NOTE

C The Control Panel displayed above shows only copier functions. Please refer to the

appropriate operating instructions for other control panel functions or in the Panasonic

Document Management System CD-ROM for the Printer control panel functions.

C The illustration above shows the DP-2010E control panel.

/ CLEAR Key C Clears the copy count in the display. ——

0

ENERGY-SAVER Key

C Can save power while the copier is not in use.

Page 24

1 RESET Key C Resets all features to the initial power-on state. ——

(For DP-2010E only)

P10-11_1810_2010_GAP(gbr).p65 5/27/02, 4:59 PM10

11

For DP-1510P/1810P

Control Panel

LCD Display

Warning Indications

J Add Paper

? Add Toner

I Misfeed

2 Call Service

No Contents Refer to

2 STOP Key C Stops the copy run. ——

3 START Key C Used to start an operation. ——

4

INTERRUPT Key, MEMORY IN Key, M1/M2 Keys

C Interrupt Key interrupts other copy jobs while making copies.

C Memory In Key registers two copy jobs for recall at a later time.

C

M1/M2 Keys are used to store a Job in Memory or to recall a Job stores in Memory.

Pages 22, 24

5

Cursor Keys

CC

C Select copy ratio and function modes using (G or F).

——

6 PAPER TRAY Key

CC

C Used to select the paper tray manually. ——

7

COPY SIZE Key

C

Used to select Reduction/Enlargement only. For additional details, see page 13.

——

8

ORIGINAL SIZE Key

C

Used to select the original size manually. For additional details, see page 13.

——

9 PRINT Key

CC

C When selecting the Printer ON/OFF Line. ——

NOTE

C The Control Panel displayed above shows only copier functions. Please refer

to the appropriate operating instructions for other control panel functions or in

the Panasonic Document Management System CD-ROM for the Printer

control panel functions.

Before Starting

:

2-Sided/1-Sided Copy Key

C Used to select 1 \ 2, 2 \ 2 and 2 \ 1, Book \ 2 copying

——

P10-11_1810_2010_GAP(gbr).p65 6/18/02, 3:53 PM11

12

Basic Copy

Full Size Copying

■■

■ Copying the Same Size Originals (1:1)

Copy size is automatically selected.

1

Place the Original

LCD Display (Sample)

ORIGINAL SIZE Key

Select the Original Size on units

without the ADF/i-ADF Option.

NOTE

CLEAR Key

2

Number of Copies*

Up to 999

3

Press START**

# Select the Original Type

PHOTO : Originals are mainly composed of photo.

TEXT/PHOTO: Combined originals with text and photo.

TEXT : Originals are mainly composed of text.

$ Select Exposure Control

Press the DARKER/LIGHTER keys to adjust the exposure.

■■

■ Manually Selecting Exposure Control or Original Type

∗

Use Clear key when cancelling the copy count.

∗∗

While the copier is warming up, you may position your original on the copier, enter

your copy job selections and press the Start key. The COPY JOB RESERVED

indicator displays until the warm up cycle is completed and the copy job is

automatically started.

READY TO COPY

COPIES:001

P12_1810_2010_GAP(gbr).p65 5/27/02, 4:59 PM12

13

■■

■ Copying with Preset Ratios

Basic Copy

100 87 71 50

115 100 82 58

141 122 100 71

200 173 141 100

Reduction or Enlargement Copying

RESET

Making Copies

1

Place the

Original

2

Select the

ORIGINAL SIZE

3

Select the COPY

SIZE

4

Number of

Copies

C If the desired copy size is different from the paper size loaded in the paper

tray, use the sheet bypass. (See page 15)

C Press the RESET key to cancel all job settings.

5

Press

START

Example: Reduction

Original size Copy size

A3 A4

The correct ratio is automatically selected.

Reduction and enlargement ratios (%)

Original

Size

Copy Size

A3 B4 A4 A5

A3

B4

A4

A5

C When changing the paper tray, press the

Paper Tray key.

NOTE

A3

->A4

B

[A4

B

]

ZOOM: 71% COPIES:001

P13-15_1810_2010_GAP(gbr).p65 5/27/02, 4:59 PM13

14

NOTE

ATTENTION

■■

■ Zoom

Copies with variable zoom ratios from 50 % to 200 % in 1 % increments.

RESET

Zoom Copying

Basic Copy

(Example: 125 % Zoom)

1

Place the

Original

2

Press Cursor (G or F)

keys to select Zoom Ratio

4

Number

of Copies

5

Press

START

C When changing the paper size after setting the zoom ratio, please use the paper tray

key.

C Press the RESET key to cancel all job settings.

3

Select ORIGINAL

SIZE

(without using

ADF/i-ADF)

A4 ->A4

B

[A4

B

]

ZOOM:125% COPIES:001

B

P13-15_1810_2010_GAP(gbr).p65 5/27/02, 4:59 PM14

15

NOTE

ATTENTION

Sheet

Bypass

# Place the sheets of paper into

the tray. (approximately up to

50 A4 size sheets 80 /

gg

gm

2

)

Basic Copy

Using the Sheet Bypass

■■

■ Copying on Special Paper, etc.

1

Place the original.

Open the sheet bypass.

2

Pull out the sheet bypass tray

until it stops.

(For A3 size only)

3

Insert the paper until it stops.

$ Adjust the side guides.

Incorrect adjustment may cause the

paper to wrinkle, misfeed or skew.

Press START.

Side Guides

C Adjust the side guides properly to avoid skewing, wrinkling or misfeeding.

C Do not feed curled paper through the sheet bypass to avoid misfeed.

Do not fill above.

Making Copies

P13-15_1810_2010_GAP(gbr).p65 5/27/02, 4:59 PM15

16

2 in 1 Copy

■ 2 in 1 Copy

From two 1-Sided originals, side by side, to 1-Sided pages.

Creative Features

1 \ 2 (Layout)*

2 \ 1 (Layout)*

Portrait (Orientation)*

Landscape (Orientation)*

1 \ 2 (Layout)*

2 \ 1 (Layout)*

4

Number of

Copies

■■

■ Procedure

ADF/i-ADF

Face-Up

1

Place the

Originals

2

Press 2

in 1 key

(

3

)

COPY SIZE

(Reduction/

Enlargement

Only)

5

Press

START

C The ADF/i-ADF is required for 2 in 1 copy.

CPress the RESET key to cancel all job settings.

CNumbers in parenthesis “ ( ) ” represent that, an additional step is required to

activate the feature.

∗

The Orientation and Layout can be set in the Copier Settings function mode.

(See page 30)

NOTE

P16-17_1810_2010_GAP(gbr).p65 5/27/02, 5:00 PM16

17

NOTE

C To reset all job settings, press the RESET key.

3

ORIGINAL SIZE

(A4 or A3 size Only)

4

Number of

Copies

5

Press

START

Platen A3 size original

A4

Book Mark

■ 2 PAGE Copy

Copying two facing pages on a A3 size original on two separate A4 size sheets.

■■

■ Procedure

1

Place the

Originals

2

Press the 2

PAGE COPY

key

2 PAGE COPY

Creative Features

Making Copies

Centre book

by length

and width

according

to centre

marks.

P16-17_1810_2010_GAP(gbr).p65 5/27/02, 5:00 PM17

18

NOTE

BOOK/EDGE/MARGIN

Creative Features

■ BOOK Key

Eliminates dark inner binding shadows when copying from a book.

■ EDGE Key

Creates a blank edge.

■ MARGIN Key

Shifts the image to the right or left.

■■

■ Procedure

∗

Initial setting (Factory setting) can be changed in the Copier Settings function mode.

(See page 30)

∗∗

If a part of the copied image is missing when using the Margin mode, change the

Frame Reduction setting to ON.

(See page 30)

CPress the RESET key to cancel all job settings.

Book

∗

Initial Book Margin setting (Factory setting): 20 mm

∗

Initial Equal Rate setting (Factory setting): 5 mm

∗

Initial Left Margin setting (Factory setting): 10 mm

Edge

Margin**

1

Place the

Original

2

Press BOOK, EDGE

or MARGIN key

5

Press

START

4

Number

of Copies

BOOK MARGIN

CENTER VOID = 20mm ∨∧

EQUAL RATE

VOID MARGIN = 5mm ∧

LEFT MARGIN

10mm ∨∧

3

Press Cursor (G or F) keys to adjust

the void width while the button is

blinking. (approx. 5 sec.)

CVoid/Margin width: 5-99 mm

P18_1810_2010_GAP(gbr).p65 5/27/02, 5:00 PM18

19

2-Sided/1-Sided Copy (For DP-2010E)

Creative Features

■■

■ Key Operation

Press 2-Sided/1-Sided Copy key (circulation) to select a 2-Sided/1-Sided Copy function.

1 \ 2

From 1-Sided originals to 2-Sided

copies.

(See page 20)

2 \ 2

From 2-Sided originals to 2-Sided

copies.

(See page 20)

Book \ 2

From book originals to 2-Sided copies. (See page 21)

2 \ 1

From 2-Sided originals to 1-Sided

copies.

(See page 20)

NOTE

2-Sided/1-Sided Copy key

C 2-Sided originals may be handled either manually or automatically using the

i-ADF (DA-AR201).

C 2-Sided/1-Sided Copy function is only available for DP-2010E.

Making Copies

P19_1810_2010_GAP(gbr).p65 5/27/02, 5:00 PM19

20

1

\\

\ 2 / 2

\\

\1 / 2

\\

\ 2 Copy (For DP-2010E)

■ 1

\\

\ 2 Copy

From 1-Sided originals to

2-Sided copies.

(From Copier Platen & i-ADF/

ADF)

■ 2

\\

\ 1 Copy

From 2-Sided originals to

1-Sided copies.

(Using i-ADF)

Creative Features

NOTE

■ 2

\\

\ 2 Copy

From 2-Sided originals to

2-Sided copies.

(Using i-ADF)

Long Edge (Binding)* Long Edge (Binding)* Long Edge (Binding)

Short Edge (Binding)

* Short Edge (Binding)* Short Edge (Binding)

■■

■

Procedure

i-ADF

Face-Up

1

Place the

Originals

2

Press 2-Sided/

1-Sided Copy key

(circulation) to

select 1 \ 2, 2 \ 2

or 2 \ 1

Number of

Copies

(

3

)

COPY SIZE

(Reduction/

Enlargement Only)

45

Press

START

C To reset each selection, press the RESET key.

∗

The initial setting of binding location for 1 \ 2 Copy and 2 \ 1 Copy (Long edge or

Short edge) can be set in function mode. (See page 30)

C 1 \ 2, 2 \ 2, 2 \ 1 Copy function is only available for DP-2010E.

(When selecting 1 \ 2 Copy or 2 \ 1 Copy)

BINDING:LONG EDGE

PRESS < > TO SELECT

Press the I or H key to select

the binding location.

P20_1810_2010_GAP(gbr).p65 5/27/02, 5:00 PM20

Page is loading ...

Panasonic DP1510 Operating instructions

Panasonic DP1510 Operating instructions

Related papers

Other documents