Electrolux EWS126410W User manual

Category
Washing machines
Type
User manual
user manual
Washing Machine
EWS 106410 W - EWS 106410 S - EWS 126410 W
Electrolux. Thinking of you.
Share more of our thinking at www.electrolux.com
Contents
Safety information 2
Product description 4
Control panel 5
First use 7
Personalisation 8
Daily use 8
Helpful hints and tips 11
Washing programmes 13
Care and cleaning 16
What to do if... 20
Technical data 22
Consumption values 23
Installation 23
Electrical connection 26
Environment concerns 26
Subject to change without notice
Safety information
Important! Read carefully & keep for future
reference.
The safety of Your appliance complies with
the industry standards and with legal re-
quirements on the safety of appliances.
However, as manufacturers, we feel it is
our duty to provide the following safety
notes.
It is most important that this instruction
book should be retained with the appli-
ance for future reference. Should the ap-
pliance be sold or transferred to another
owner, or should you move house and
leave the appliance, always ensure that the
book is supplied with the appliance in or-
der that the new owner can get to know
the functioning of the appliance and the
relevant warnings.
You MUST read them carefully before in-
stalling or using the appliance.
Before first starting up, check the appli-
ance for any damage incurred during
transport. Never connect up a damaged
appliance . If parts are damaged, contact
your supplier.
If the appliance is delivered in the winter
months when there are minus tempera-
tures. Store it at room temperature for 24
hours before using for the first time.
General safety
It is dangerous to alter the specifications or
attempt to modify this product in any way.
During high temperature wash pro-
grammes the door glass may get hot. Do
not touch it!
Make sure that small pets do not climb into
the drum. To avoid this, please check into
the drum before using.
Any objects such as coins, safety pins,
nails, screws, stones or any other hard,
sharp material can cause extensive dam-
age and must not be placed into the ma-
chine.
Only use the advised quantities of fabric
softener and detergent. Damage to the
fabric can ensue if you over-fill. Refer to the
manufacturer’s recommendations of
quantities.
Wash small items such as socks, laces,
washable belts etc in a washing bag or pil-
low case as it is possible for such items to
slip down between the tub and the inner
drum.
Do not use your washing machine to wash
articles with whalebones, material without
hems or torn material.
Always unplug the appliance and turn off
the water supply after use, cleaning and
maintenance.
Under no circumstances should you at-
tempt to repair the machine yourself. Re-
pairs carried out by inexperienced people
may cause injury or serious malfunction-
ing. Contact your local Service Centre. Al-
ways insist on genuine spare parts.
2 electrolux
Installation
This appliance is heavy. Care should be
taken when moving it.
When unpacking the appliance, check that
it is not damaged. If in doubt, do not use it
and contact the Service Centre.
All packing and transit bolts must be re-
moved before use. Serious damage can
occur to the product and to property if this
is not adhered to. See relevant section in
the user manual.
After having installed the appliance, check
that it is not standing on the inlet and drain
hose and the worktop is not pressing the
electrical supply cable against the wall.
If the machine is situated on a carpeted
floor, please adjust the feet in order to al-
low air to circulate freely under the appli-
ance.
Always be sure, that there is no water leak-
age from hoses and their connections after
the installation.
If the appliance is installed in a location
subject to frost, please read the “dangers
of freezing” chapter.
Any plumbing work required to install this
appliance should be carried out by a quali-
fied plumber or competent person.
Any electrical work required to install this
appliance should be carried out by a quali-
fied electrician or competent person.
Use
This appliance is designed for domestic
use. It must not be used for purposes other
than those for which it was designed.
Only wash fabrics which are designed to
be machine washed. Follow the instruc-
tions on each garment label.
Do not overload the appliance. See the
Washing Programme Table.
Before washing, ensure that all pockets
are empty and buttons and zips are fas-
tened. Avoid washing frayed or torn arti-
cles and treat stains such as paint, ink,
rust, and grass before washing. Under-
wired bras must NOT be machine washed.
Garments which have been in contact with
volatile petroleum products should not be
machine washed. If volatile cleaning fluids
are used, care should be taken to ensure
that the fluid is removed from the garment
before placing in the machine.
Never pull the power supply cable to re-
move the plug from the socket; always
take hold of the plug itself.
Never use the appliance if the power sup-
ply cable, the control panel, the working
surface or the base are damaged so that
the inside of the washing machine is ac-
cessible.
Child Safety
This appliance is not intended for use by
person (including children) with reduced
physical sensory or mental capabilities or
lack of experience and knowledge unless
they have been given supervision or in-
struction concerning use of the appliance
by a person responsible for their safety.
Children should be supervised to ensure
that they do not play with the appliance.
The packaging components (e.g. plastic
film, polystyrene) can be dangerous to chil-
dren - danger of suffocation! Keep them
out of children's reach.
Keep all detergents in a safe place out of
children’s reach.
Make sure that children or pets do not
climb into the drum. To prevent children or
pets becoming trapped inside the drum
the machine incorporates a special fea-
ture. To activate this device, rotate the but-
ton (without pressing it) inside the door
clockwise until the groove is horizontal. If
necessary use a coin. To disable this de-
vice and restore the possibility of closing
the door, rotate the button anticlockwise
until the groove is vertical.
electrolux 3
Product description
Your new appliance meets all modern requirements for effective treatment of laundry
with low water, energy and detergent consumption. Its new washing system allows total
use of detergent and reduces water consumption so saving energy.
1 2
3
4
5
6
1 Detergent dispenser drawer
2 Control panel
3 Door opening handle
4 Rating Plate
5 Drain pump
6 Adjustable feet
Detergent dispenser drawer
Compartment for detergent used for pre-
wash and soak phase or for stain remover
used during the stain action phase (if availa-
ble). The prewash and soak detergent is
added at the beginning of the wash pro-
gramme. The stain remover is added during
the stain action phase.
Compartment for powder or liquid deter-
gent used for main wash. If using liquid de-
tergent pour it just before starting the pro-
gramme.
Compartment for liquid additives (fabric
softener, starch).
Follow the product manufacturer’s recom-
mendations on quantities to use and do not
exceed the «MAX» mark in the detergent
dispenser drawer. Any fabric softener or
starching additives must be poured into the
compartment before starting the wash pro-
gramme.
4 electrolux
Programme Chart
Various programme charts in different lan-
guages are supplied with the appliance. One
is on the front side of the detergent dispenser
drawer and the others are attached into the
user manual assy. The chart in the drawer
can be replaced easily: remove the chart
from the drawer by pulling it towards the right
and insert the chart with the language re-
quired.
Control panel
Below is a picture of the control panel. It shows the programme selector dial as well as
the buttons, pilot light and the display. These are presented by relevant numbers on the
following pages.
1 2 4 5 6 7
8
9
10
3
1
Programme selector dial
2 TEMPERATURE button
3 SPIN reduction button
4 PREWASH button
5 EXTRA RINSE button
6
DELAY START button
7 Display
8 START/PAUSE button
9 DOOR LOCKED pilot light
10 TIME MANAGER buttons
Programme Selector Dial
It allows you to switch the appliance on/off
and/or to select a programme.
Temperature
This button allows you to increase or de-
crease the washing temperature.
Spin Reduction
By pressing this button you can change the
spin speed of the selected programme or to
select Rinse Hold or No Spin option.
No spin
By selecting this option, all spinning phases
are suppressed and replaced by a drain, so
as not to wrinkle the laundry. Recommended
for extremely delicate fabrics. On some pro-
grammes the rinses will be performed with
more water.
Rinse hold
By selecting this function the water of the last
rinse is not emptied out to prevent the fabrics
from creasing. Before opening the door it will
be necessary to empty out the water. To
empty out the water, please read the para-
graph «At the end of the programme».
Prewash
By selecting this option the machine per-
forms a prewash cycle before the main wash
phase. The washing time will be prolonged.
This option is recommended for heavily
soiled laundry.
electrolux 5
Extra Rinse
This appliance is designed to save energy. If
it necessary to rinse the laundry using an ex-
tra quantity of water (extra rinse), select this
option. Some additional rinses will be per-
formed. This option is recommended for
people who are allergic to detergents, and in
areas where the water is very soft.
Delay Start
The programme can be delayed from 30 min
- 60 min - 90 min, 2 hours and then by 1 hour
up to a maximum of 20 hours by means of
this button.
Start Pause
This button allows you to start or to interrupt
the selected programme.
Time Manager
These buttons allows you to modify the pro-
gramme duration automatically proposed by
the appliance.
Door locked pilot light
The pilot light 9 illuminates when the pro-
gramme starts and indicates if the door can
be opened:
light on: the door cannot be opened. The
machine in working or has stopped with
water left in the tub.
light off: the door can be opened. The pro-
gramme is finished or the water has been
emptied out.
light flashing: the door is opening
Display
7.4 7.5 7.1
7.27.3
The display shows the following information:
7.1:
Duration of the selected programme
After selecting a programme, the duration
is displayed in hours and minutes (for ex-
ample 2.05 ). The duration is calculated
automatically on the basis of the maximum
recommended load for each type of fabric.
After the programme has started, the time
remaining is updated every minute.
Delayed start
The Selected delay set by pressing the rel-
evant button appears on the display for
few seconds, then the duration of the se-
lected programme is displayed again.
Alarm codes
In the event of operating problems, some
alarm codes can be displayed, for example
E20 (see paragraph «What to do if...»).
Incorrect option selection
If an option which is not compatible with
the set wash programme is selected, the
message Err is displayed at the bottom of
the display for a few seconds and the in-
tegrated red light of button 8 start flashing.
End of programme
When the programme has finished three
flashing zeros are displayed, the pilot light
9 and the pilot light of button 8 go out and
the door can be opened.
7.2: Washing programme phase icons
Wash
6 electrolux
Rinses
Drain
Spin
By selecting the wash programme, the
washing programme phase icons corre-
sponding to the various phases making up
the programme are shown in the bottom part
of the display. After having pressed button
8 only the icon of the running phase stays on.
7.3: Heating phase
During the washing cycle the display shows
a temperature icon indicating that the appli-
ance has started the heating phase of the
water in the tub.
7.4: Soil degree icons
Intensive
Normal
Daily
Light
Quick
Super Quick
Refresh
Super Refresh
When selecting a programme on the display
appears an icon indicating the degree of soil-
ing automatically proposed by the machine.
7.5: Child safety lock
(see «Child Safety
Lock» paragraph).
Table of Symbols
= Cottons = Blanket
= Synthetics = Temperature
= Delicates = Cold
= Wool = No Spin
= Silk = Rinse Hold
= Lingerie = Prewash
= Soak = Extra Rinse
= Rinse = Delay Start
= Drain = Start/Pause
= Spin = Child safety lock
= Energy saving (Economy) = Door locked
= Easy iron = Time Manager
= Jeans
First use
Ensure that the electrical and water
connections comply with the installa-
tion instructions.
Ensure that the drum is empty.
Pour 2 liters of water into the main
wash compartment
of the deter-
gent drawer in order to activate the
ECO valve. Then run a cotton cycle at
the highest temperature without any
laundry in the machine, to remove any
manufacturing residue from the drum
and tub. Pour 1/2 a measure of de-
tergent into the main wash compart-
ment and start the machine.
electrolux 7
Personalisation
Acoustic signals
The machine is provided with an acoustic
device, which sounds in the following cases:
at the end of the cycle
if there is a fault.
By pressing the 4 and 5 buttons simultane-
ously for about 6 seconds , the acoustic
signal is deactivated (except if there is a fault).
By pressing these 2 buttons again, the
acoustic signal is reactivated.
Child safety lock
This device permits you to leave the appli-
ance unattended and not to worry that chil-
dren might be injured by or cause damage to
the appliance. This function remains enabled
also when the washing machine is not work-
ing.
There are two different ways to set this op-
tion:
1. Before pressing button 8 : it will be im-
possible to start the machine.
2. After pressing button 8 : it will be impos-
sible to change any other programme or
option.
To enable or disable this option press simul-
taneously for about 6 seconds buttons 5 and
6 until on the display, the icon
appears or
disappears.
Daily use
Load the laundry
Open the door by carefully pulling the door
handle outwards. Place the laundry in the
drum, one item at a time, shaking them out
as much as possible. Close the door.
Measure out the detergent and the fab-
ric softener
Pull out the dispenser drawer until it stops.
Measure out the amount of detergent re-
quired, pour it into the main wash compart-
ment
or in the appropriate compartment
if the selected programme/option it requires
(see more details in «Detergent dispenser
drawer»).
If required, pour fabric softener into the com-
partment marked
(the amount used must
not exceed the «MAX» mark in the drawer).
Close the drawer gently.
8 electrolux
Select the required programme by
turning the programme selector dial (1)
Turn the programme selector dial to the re-
quired programme. The washing machine
will propose a temperature and automatically
select the maximum spin value provided for
the programme you have chosen. You can
change these values by operating the corre-
sponding buttons. The green pilot light of the
button 8 starts to flash.
The selector dial can be turned either clock-
wise or counterclockwise. Turn to position
to reset programme/Switching the ma-
chine off.
At the end of the programme the selec-
tor dial must be turned to position
, to
switch the machine off.
Caution! If you turn the programme
selector dial to another programme
when the machine is working, the red
pilot light of button 8 will blink 3 times
and the message Err is displayed to
indicate a wrong selection. The machine
will not perform the new selected
programme.
Programme Option buttons
Depending on the programme, different
functions can be combined. These must be
selected after choosing the desired pro-
gramme and before pressing the button 8 .
Select the temperature by pressing
button 2
By selecting a programme, the appliance
proposes automatically a default tempera-
ture.
Press this button repeatedly to increase or
decrease the temperature, if you want your
laundry to be washed at a different temper-
ature.
Reduce the spin speed by pressing
button 3
By selecting a programme, the appliance
proposes automatically the maximum spin
speed provided for that programme.
Press button 3 repeatedly to change the spin
speed, if you want your laundry to be spun at
a different speed. The relevant light illumi-
nates.
Select the available option by pressing
buttons 3, 4 and 5
Depending on the selected programme, dif-
ferent functions can be combined before
pressing the button 8 . By selecting an option
the relevant pilot light illuminates.
If an incorrect option is selected, the integra-
ted red pilot light of the button 8 flashes 3
times and the Err message appears on the
display for few seconds.
For compatibility among the washing
programmes and the options see chap-
ter «Washing Programmes».
Select the Delay Start by pressing
button 6
Before you start the programme, if you wish
to delay the start, press the button 6 repeat-
edly, to select the desired delay. The relevant
pilot light goes on.
The selected delay time value (up to 20
hours) will appear on the display a few sec-
onds, then the duration of the programme
will appear again.
You must select this option after you have set
the programme and before you press button
8 .
You can cancel or modify the delay time at
any moment, before you press button 8 .
Selecting the delayed start:
1. Select the programme and the required
options.
electrolux 9
2. Select the delay start by pressing the but-
ton 6 .
3. Press button 8 :
the machine starts its hourly count-
down.
The programme will start after the se-
lected delay has expired.
Cancelling the delayed start after having
pressed button 8 :
1. Set the washing machine to PAUSE by
pressing button 8 .
2.
Press button 6 once until the symbol 0’ is
displayed
3. Press button 8 again to start the pro-
gramme.
Important! The selected delay can be
changed only after selecting the washing
programme again.
The Delay Start can not be selected with
DRAIN programme.
Start the programme by pressing button
8
To start the selected programme, press the
button 8 , the green pilot light of the button
8 stops blinking.
To interrupt a programme which is running,
press the button 8 : the green pilot light starts
blinking.
To restart the programme from the point at
which it was interrupted, press the button 8
again . If you have chosen a delayed start,
the machine will begin the countdown. If an
incorrect option is selected, the red pilot light
of the button 8 blinks for 3 times the message
Err is displayed for a few seconds.
Select the Time Manager option by
pressing buttons 10
By pressing these buttons repeatedly, the
duration of the washing cycle can be in-
creased or decreased. The soil level icon will
appear on the display to indicate the chosen
degree of soil. This option is available only
with Cotton , Synthetic and Delicate pro-
grammes.
Soil Level Icon Type of fabric
Intensive For heavy soiled
items
Normal For normal soiled
items
Daily For daily soiled items
Soil Level Icon Type of fabric
Light For slightly soiled
items
Quick For very slightly
soiled items
Super Quick
1)
For items used or
worn for a short time
Refresh
1)
2)
For refreshing items
only
Super Re-
fresh
1)
2)
For refreshing a very
few items only
1) We recommend you to reduce the load sizes (see
Washing programmes table).
2) When you select this option the relevant icon appears
just for a while and then it disappears immediately.
Altering an option or a running
programme
It is possible to change some options before
the programme carries them out .
Before you make any change, you must
PAUSE the appliance by pressing the button
8 (if you wish to change the Time Manager
option, you must cancel the running pro-
gramme and make your selection again).
Changing a running programme is possible
only by resetting it. Turn the programme se-
lector dial to
and then to the new pro-
gramme position. Start the new programme
by pressing the button 8 again. The washing
water in the tub will be not emptied out.
Interrupting a programme
Press the button 8 to interrupt a programme
which is running, the corresponding green
pilot light starts blinking.
Press the button again to restart the pro-
gramme.
Cancelling a programme
Turn the selector dial to
to cancel a pro-
gramme which is running.
You can select now a new programme.
Opening the door
After the programme has started (or during
the delay time) the door is locked, if you need
to open it, set first the machine to PAUSE by
pressing the button 8 .
After a few minutes the pilot light 9 goes out
and it is possible to open the door.
If this pilot light remains lit, this means that
the machine is already heating or that the
10 electrolux
water level is too high. In any case, do not try
to force the door!
If you cannot open the door but you need to
open it you have to switch the machine off by
turning the selector dial to O . After a few mi-
nutes the door can be opened (pay atten-
tion to the water level and tempera-
ture!) .
After closing the door, it is necessary to se-
lect the programme and options again and to
press button 8 .
At the end of the programme
The machine stops automatically. Three
blinking 0.00 appear on the display and the
pilot light of button 8 goes off. Some acoustic
signals sound.
If a programme or an option that ends with
water left in the tub has been selected, the
door remains locked to indicate that the wa-
ter must be emptied out before opening the
door.
Follow the below instructions to empty out
the water:
1. Turn the programme selector dial to O .
2. Select the draining or spinning pro-
gramme.
3. Reduce the spin speed if needed, by
pressing the relevant button.
4. Press button 8 .
At the end of the programme, the door is re-
leased and can be opened. Turn the pro-
gramme selector dial to O to switch the ma-
chine off.
Remove the laundry from the drum and care-
fully check that the drum is empty. If you do
not intend to carry out another wash, close
the water tap. Leave the door open to pre-
vent the formation of mildew and unpleasant
smells.
Stand by : once the programme has finished
after a few minutes the energy saving system
will be enabled. The brightness of the display
is reduced. By pressing any button the ap-
pliance will come out of the energy saving
status.
Helpful hints and tips
Sorting out the laundry
Follow the wash code symbols on each gar-
ment label and the manufacturer’s washing
instructions. Sort the laundry as follows:
whites, coloureds, synthetics, delicates,
woollens.
Before loading the laundry
Never wash whites and coloureds together.
Whites may lose their «whiteness» in the
wash.
New coloured items may run in the first wash;
they should therefore be washed separately
the first time.
Button up pillowcases, close zip fasteners,
hooks and poppers. Tie any belts or long
tapes.
Remove persistent stains before washing.
Rub particularly soiled areas with a special
detergent or detergent paste.
Treat curtains with special care. Remove
hooks or tie them up in a bag or net.
Removing stains
Stubborn stains may not be removed by just
water and detergent. It is therefore advisable
to treat them prior to washing.
Blood: treat fresh stains with cold water. For
dried stains, soak overnight in water with a
special detergent then rub in the soap and
water.
Oil based paint: moisten with benzine stain
remover, lay the garment on a soft cloth and
dab the stain; treat several times.
Dried grease stains: moisten with turpen-
tine, lay the garment on a soft surface and
dab the stain with the fingertips and a cotton
cloth.
Rust: oxalic acid dissolved in hot water or a
rust removing product used cold. Be careful
with rust stains which are not recent since the
cellulose structure will already have been
damaged and the fabric tends to hole.
Mould stains: treat with bleach, rinse well
(whites and fast coloureds only).
Grass: soap lightly and treat with bleach
(whites and fast coloureds only).
electrolux 11
Ball point pen and glue: moisten with ace-
tone
1)
, lay the garment on a soft cloth and
dab the stain.
Lipstick: moisten with acetone as above,
then treat stains with methylated spirits.
Treat any residual marks with bleach.
Red wine: soak in water and detergent,
rinse and treat with acetic or citric acid, then
rinse. Treat any residual marks with bleach.
Ink: depending on the type of ink, moisten
the fabric first with acetone
1)
, then with acetic
acid; treat any residual marks on white fab-
rics with bleach and then rinse thoroughly.
Tar stains: first treat with stain remover, me-
thylated spirits or benzine, then rub with de-
tergent paste.
Detergents and additives
Good washing results also depend on the
choice of detergent and use of the correct
quantities to avoid waste and protect the en-
vironment.
Although biodegradable, detergents contain
substances which, in large quantities, can
upset the delicate balance of nature.
The choice of detergent will depend on the
type of fabric (delicates, woollens, cottons,
etc.), the colour, washing temperature and
degree of soiling.
All commonly available washing machine de-
tergents may be used in this appliance:
powder detergents for all types of fabric
powder detergents for delicate fabrics
(60°C max) and woollens
liquid detergents, preferably for low tem-
perature wash programmes (60°C max)
for all types of fabric, or special for wool-
lens only.
The detergent and any additives must be
placed in the appropriate compartments of
the dispenser drawer before starting the
wash programme.
If using liquid detergents, a programme
without prewash must be selected.
Your appliance incorporates a recirculation
system which allows an optimal use of the
concentrated detergent.
Follow the product manufacturer’s recom-
mendations on quantities to use and do not
exceed the «MAX» mark in the detergent
dispenser drawer .
Quantity of detergent to be used
The type and quantity of detergent will de-
pend on the type of fabric, load size, degree
of soiling and hardness of the water used.
Follow the product manufacturers’ instruc-
tions on quantities to use.
Use less detergent if:
you are washing a small load
the laundry is lightly soiled
large amounts of foam form during wash-
ing.
Degrees of water hardness
Water hardness is classified in so-called “de-
grees” of hardness. Information on hardness
of the water in your area can be obtained
from the relevant water supply company, or
from your local authority. If the water hard-
ness degree is medium or high we suggest
you to add a water softener following always
the manufacturer’s instructions. When the
degree of hardness is soft, readjust the quan-
tity of the detergent.
1) do not use acetone on artificial silk
12 electrolux
Washing programmes
Programme
Maximum and Minimum Temperature
Cycle Description
Maximum Spin Speed
Maximum Fabrics Load
Type of Laundry
Options
Detergent
Compartment
COTTONS and LINENS
90° - Cold
Main wash - Rinses
Maximum spin speed: 1000 rpm
(EWS106410W-106410S)
Maximum spin speed: 1200 rpm (EWS126410W)
Max. load 6 kg - Reduced load 3 kg
1)
White and coloured cotton (normally soiled items).
SPIN REDUCTION
NO SPIN
RINSE HOLD
PREWASH
2)
EXTRA RINSE
TIME MANAGER
SYNTHETICS
60° - Cold
Main wash - Rinses
Maximum spin speed: 900 rpm
Max. load 3 kg - Reduced load 1,5 kg
1)
Synthetic or mixed fabrics: underwear, coloured gar-
ments, non-shrink shirts, blouses.
SPIN REDUCTION
NO SPIN
RINSE HOLD
PREWASH
2)
EXTRA RINSE
TIME MANAGER
DELICATES
40° - Cold
Main wash - Rinses
Maximum spin speed: 700 rpm
Max. load 3 kg - Reduced load 1,5 kg
1)
Delicate fabrics: acrylics, viscose, polyester.
NO SPIN
RINSE HOLD
PREWASH
2)
EXTRA RINSE
TIME MANAGER
WOOL
40° - Cold
Main wash - Rinses
Maximum spin speed: 1000 rpm
Max. load 1 kg
Washing programme for machine washable wool as
well as for hand washable woollens and delicate fabrics
with «hand washing» care symbol. Note : A single or
bulky item may cause imbalance. If the appliance
doesn’t perform the final spin phase, add more items,
redistribute the load manually and then select the spin-
ning programme.
SPIN REDUCTION
NO SPIN
RINSE HOLD
SILK
30° - Cold
Main wash - Rinses
Maximum spin speed: 700 rpm
Max. load 1 kg
Delicate washing programme suitable for silk and mixed
synthetic items.
NO SPIN
RINSE HOLD
electrolux 13
Programme
Maximum and Minimum Temperature
Cycle Description
Maximum Spin Speed
Maximum Fabrics Load
Type of Laundry
Options
Detergent
Compartment
LINGERIE
40° - Cold
Main wash - Rinses
Maximum spin speed: 1000 rpm
Max. load 2 kg
This programme is suitable for very delicate items such
a lingerie, bras and underwear. The maximum spin
speed is automatically reduced.
SPIN REDUCTION
NO SPIN
RINSE HOLD
SOAK
30°
Prewash - Soak for about 40 minutes - Stop with water
in the tub
Max. load 6 kg
Special programme for heavily soiled laundry. The ma-
chine performs a soak at 30°C. At the end of this time
the machine will stop automatically with water left in the
tub.
Before starting a new washing phase, it is necessary to
empty out the water by:
Draining only : turn the programme selector dial to
Drain programme. (Press the button 8 ).
Draining and spinning : turn the programme selec-
tor dial to programme Spin, reduce the spin speed by
means of button 3 , and then press button 8 .
Important! This programme cannot be used for very
delicate fabrics as silk or wool. Pour the detergent for
the soak programme into the compartment marked . At
the end of the soak (after having emptied out the water)
you can select the washing programme. (First turn the
programme selector dial to
, then to the programme
and press the button 8 ).
RINSE
Rinse - Long spin
Maximum spin speed: 1000 rpm
(EWS106410W-106410S)
Maximum spin speed: 1200 rpm (EWS126410W)
Max. load 6 kg
With this programme it is possible to rinse and spin cot-
ton garments which have been washed by hand. To in-
tensify the rinsing action, select the option EXTRA
RINSE. The appliance will add some additional rinses.
SPIN REDUCTION
NO SPIN
RINSE HOLD
EXTRA RINSE
DRAIN
Draining of water
Max. load 6 kg
For emptying out the water of the last rinse in pro-
grammes with the option selected, which ends with
water left in the tub.
14 electrolux
Programme
Maximum and Minimum Temperature
Cycle Description
Maximum Spin Speed
Maximum Fabrics Load
Type of Laundry
Options
Detergent
Compartment
SPIN
Drain and long spin
Maximum spin speed: 1000 rpm
(EWS106410W-106410S)
Maximum spin speed: 1200 rpm (EWS126410W)
Max. load 6 kg
Separate spin for hand washed garments and after pro-
grammes with the Rinse Hold and No Spin option se-
lected. You can choose the spin speed by pressing the
relevant button to adapt it to the fabrics to be spun.
SPIN REDUCTION
COTTONS ECONOMY
90° - 40°
Main wash - Rinses
Maximum spin speed: 1000 rpm
(EWS106410W-106410S)
Maximum spin speed: 1200 rpm (EWS126410W)
Max. load 6 kg
White and fast coloured cotton
This programme can be selected for slightly or normally
soiled cotton items. The temperature will decrease and
the washing time will be extended. This allows to obtain
a good washing efficiency so saving energy.
SPIN REDUCTION
NO SPIN
RINSE HOLD
PREWASH
2)
EXTRA RINSE
EASY IRON
60° - Cold
Main wash - Rinses
Maximum spin speed: 900 rpm
Max. load 1 kg
This programme can be selected for synthetic items
and mixed fabrics to be ironed. The laundry can be
gently washed and spun to avoid any creasing. In this
way ironing is easier. Furthermore the machine will per-
form additional rinses.
SPIN REDUCTION
NO SPIN
RINSE HOLD
PREWASH
2)
EXTRA RINSE
JEANS
60° - Cold
Main wash - Rinses
Maximum spin speed: 1000 rpm
Max. load 3 kg
With this programme it is possible to wash items like
pants, shirts or jackets in Jeans and also jersey realized
with hi-tech materials. (The EXTRA RINSE option will be
activated automatically).
SPIN REDUCTION
NO SPIN
RINSE HOLD
PREWASH
2)
BLANKET
40° -30°
Main wash - Rinses
Maximum spin speed: 700 rpm
Max. load 2 kg
Special programme for a single washable synthetic
blanket or duvet.
electrolux 15
Programme
Maximum and Minimum Temperature
Cycle Description
Maximum Spin Speed
Maximum Fabrics Load
Type of Laundry
Options
Detergent
Compartment
/ OFF
For cancelling the programme which is running or to
switch the machine off .
1) If you select the Quick or Super Quick option by pressing button 10 , we recommend that you reduce the maximum
load as indicated. Full loading is possible however with somewhat reduced cleaning results. If you select the Refresh
or Super Refresh option, we recommend that you reduce the load even more.
2) If using liquid detergents, a programme without PREWASH must be selected.
Care and cleaning
Warning! You must disconnect the
appliance from the electricity supply,
before you can carry out any cleaning or
maintenance work.
Descaling
The water we use normally contains lime. It
is a good idea to periodically use a water
softening powder in the machine. Do this
separately from any laundry washing, and
according to the softening powder manufac-
turer's instructions. This will help to prevent
the formation of lime deposits.
After each wash
Leave the door open for a while. This helps
to prevent mould and stagnant smells form-
ing inside the appliance. Keeping the door
open after a wash will also help to preserve
the door seal.
Maintenance wash
With the use of low temperature washes it is
possible to get a build up of residues inside
the drum.
We recommend that a maintenance wash be
performed on a regular basis.
To run a maintenance wash:
The drum should be empty of laundry.
Select the hottest cotton wash pro-
gramme.
Use a normal measure of detergent, must
be a powder with biological properties.
External cleaning
Clean the exterior cabinet of the appliance
with soap and water only, and then dry thor-
oughly.
Important! Do not use methylated spirits,
solvents or similar products to clean the
cabinet.
Cleaning the dispenser drawer
The detergent dispenser drawer should be
cleaned regularly.
The washing powder and additive dispenser
drawer should be cleaned regularly.
Remove the drawer by pressing the catch
downwards and by pulling it out.
Flush it out under a tap, to remove any traces
of accumulated powder.
To aid cleaning, the top part of the additive
compartment should be removed. Clean all
parts with water.
16 electrolux
Clean the chamber of dispenser drawer with
a brush.
Washing drum
Rust deposits in the drum may occur due to
rusting foreign bodies in the washing or tap
water containing iron.
Important! Do not clean the drum with
acidic descaling agents, scouring agents
containing chlorine or iron or steel wool.
1. Remove any rust deposits on the drum
with a cleaning agent for stainless steel.
2. Run a washing cycle without any washing
to clean off any cleaning agent residues.
Programme: Short Cotton Programme at
maximum temperature and add approx.
1/4 measuring cup of detergent.
Door seal
Check from time to time the door seal and
eliminate eventual possible objects that
could be trapped in the fold.
Drain pump
The pump should be inspected regularly and
particularly if:
the appliance does not empty and/or spin;
the appliance makes an unusual noise dur-
ing draining due to objects such as safety
pins, coins etc. blocking the pump;
a problem with water draining is detected
(see chapter “What to do if...” for more de-
tails).
Warning! Before opening the pump
door, switch the appliance off and
remove the mains plug from the socket.
Proceed as follows:
1. Unplug the appliance.
2. If necessary wait until the water has
cooled down.
3. Open the pump door levering on the
groove with a coin (or with the suitable
tool, that you can find in the bag con-
taining the instruction booklet, depend-
ing on the model).
electrolux 17
1
2
4. Place a bowl with a small edge close to
the pump to collect any spillage.
5. Pull out the emergency emptying cap
from the filter cover, using pliers.
6. When no more water comes out, un-
screw the pump cover by turning it anti-
clockwise, using pliers, and remove the
filter. Always keep a rag nearby to dry up
any water spillages when removing the
cover.
Clean the filter under a tap, to remove
any traces of fluff.
1
2
7. Remove foreign bodies and fluff from the
pump seat and from the pump impeller.
8. Check carefully whether the pump im-
peller rotates (it rotates jerkily). If it
doesn’t rotate, please contact your
Service Centre.
9. Replace the filter into the pump by in-
serting it correctly into the special
guides. Screw the pump cover firmly by
turning it clockwise.
18 electrolux
10. Replace the emergency emptying cap
into the filter cover and fix it firmly.
11. Close the pump door.
Warning! When the appliance is in use
and depending on the programme
selected there can be hot water in the
pump. Never remove the pump cover
during a wash cycle, always wait until the
appliance has finished the cycle, and is
empty. When refitting the pump cover ,
ensure it is securely re-tightened so as
to stop leaks and young children being
able to remove it.
Cleaning the water inlet filters
If you notice that the machine is taking longer
to fill, check that the filter in the water inlet
hose is not blocked.
1. Turn off the water tap.
2. Unscrew the water inlet hose.
3. Clean the filter in the hose using a hard
bristle brush.
4. Screw the hose back onto the tap.
electrolux 19
5. Unscrew the hose from the machine.
Keep a rug nearby because some water
may flow.
6. Clean the filter in the valve with a stiff
brush or with the piece of cloth.
7. Screw the hose back to the machine and
make sure the connection is tight.
8. Turn on the water tap.
Emergency emptying out
If the water is not discharged, proceed as
follows to empty out the machine:
1. pull out the plug from the power socket;
2. close the water tap;
3. if necessary, wait until the water has
cooled down;
4. open the pump door;
5. place a bowl on the floor. Remove the
emergency emptying cap from the filter.
The water should drain by gravity into the
bowl. When the bowl is full, refit the cap
into the filter. Empty the bowl. Repeat the
procedure until water stops flowing out;
6. clean the pump if necessary as previously
described;
7. screw the pump again and close the
door.
Frost precautions
If the machine is installed in a place where the
temperature could drop below 0°C, proceed
as follows:
1. Pull out the plug from the power socket.
2. Turn off the water tap.
3. Unscrew the inlet hose.
4. Place the end of the inlet hose in a bowl
placed on the floor, open the emergency
emptying cup of the filter and let water
drain out.
5. Refit the emergency emptying cap into
the filter and screw the water inlet hose
back.
6. When you intend to start the machine up
again, make sure that the room temper-
ature is above 0°C.
Important! Every time you drain the water
through the emergency emptying hose you
must pour 2 litres of water into the main wash
compartment of the detergent drawer and
then run the drain programme. This will
activate the ECO Valve device avoiding that
part of the detergent remains unused at next
washing.
What to do if...
Certain problems are due to lack of simple
maintenance or oversights, which can be
solved easily without calling out an engineer.
Before contacting your local Service Centre,
please carry out the checks listed below.
During machine operation it is possible that
the red pilot light of button 8 blinks, one of
the following alarm codes appears on the
display and some acoustic signals sound ev-
ery 20 seconds to indicate that the machine
is not working:
: problem with the water supply.
: problem with the water draining.
: door open.
Once the problem has been eliminated,
press the button 8 to restart the programme.
If after all checks, the problem persists, con-
tact your local Service Centre.
20 electrolux
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28

Electrolux EWS126410W User manual

Category
Washing machines
Type
User manual

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI