Grandstream Networks HT701 User manual

HT70X USER MANUAL

Grandstream Networks, Inc.

HT701/ HT702/HT704

Analog Telephone Adaptor

HT701 HT702 HT704

FIRMWARE VERSION 1.0.3.1 HT70X USER MANUAL Page 2 of 52

HT70X USER MANUAL

INDEX

GNU GPL INFORMATION .......................................................................... 5

CHANGE LOG ............................................................................................. 6

CHANGES FROM 1.0.1.6 USER MANUAL .......................................................................................... 6

WELCOME .................................................................................................. 7

SAFETY COMPLIANCES ...................................................................................................................... 7

WARRANTY .......................................................................................................................................... 7

CONNECT YOUR HT70X ............................................................................ 9

EQUIPMENT PACKAGING ................................................................................................................... 9

CONNECTING THE HT70X .................................................................................................................. 9

HT70X FEATRUES .................................................................................... 13

SOFTWARE FEATURES OVERVIEW ................................................................................................ 13

HARDWARE SPECIFICATION ........................................................................................................... 15

BASIC OPERATIONS ............................................................................... 16

UNDERSTANDING HT70X VOICE PROMPT..................................................................................... 16

PLACING A PHONE CALL .................................................................................................................. 18

Phone or Extension Numbers ....................................................................................................... 18

Direct IP Calls ............................................................................................................................... 18

CALL HOLD ......................................................................................................................................... 19

CALL WAITING .................................................................................................................................... 19

CALL TRANSFER ................................................................................................................................ 19

Blind Transfer ............................................................................................................................... 19

Attended Transfer ......................................................................................................................... 20

3-WAY CONFERENCING ................................................................................................................... 20

FAX SUPPORT .................................................................................................................................... 21

CALL FEATURES ..................................................................................... 22

CONFIGURATION GUIDE ........................................................................ 24

CONFIGURING THE HT70X THROUGH VOICE PROMPTS ............................................................ 24

CONFIGURING THE HT70X VIA WEB BROWSER ........................................................................... 24

Access the Web Configuration Menu ........................................................................................... 25

FIRMWARE VERSION 1.0.3.1 HT70X USER MANUAL Page 3 of 52

IMPORTANT SETTINGS ..................................................................................................................... 25

NAT Settings ................................................................................................................................. 25

DTMF Methods ............................................................................................................................. 26

Preferred VOCODER (Codec) ...................................................................................................... 26

SAVING THE CONFIGURATION CHANGES ..................................................................................... 45

REBOOTING THE HT70X FROM REMOTE ....................................................................................... 45

CONFIGURATION THROUGH A CENTRAL SERVER ...................................................................... 45

SOFTWARE UPGRADE ............................................................................ 47

FIRMWARE UPGRADE THROUGH TFTP/HTTP/HTTPS .................................................................. 47

INSTRUCTIONS FOR UPLOAD FROM LOCAL DIRECTORY: .......................................................... 48

INSTRUCTIONS FOR LOCAL FIRMWARE UPGRADE USING TFTP SERVER: ............................. 48

CONFIGURATION FILE DOWNLOAD ................................................................................................ 49

FIRMWARE AND CONFIGURATION FILE PREFIX AND POSTFIX ................................................. 49

MANAGING FIRMWARE AND CONFIGURATION FILE DOWNLOAD .............................................. 49

RESTORE FACTORY DEFAULT SETTING ............................................. 51

FIRMWARE VERSION 1.0.3.1 HT70X USER MANUAL Page 4 of 52

TABLE OF FIGURES

HT70X USER MANUAL

FIGURE 1: CONNECTING THE HT70X .................................................................................................... 10

FIGURE 2: HT70X CONNECTION DIAGRAM .......................................................................................... 12

TABLE OF TABLES

HT70X USER MANUAL

TABLE 1: DEFINITIONS OF THE HT70X CONNECTORS ........................................................................... 10

TABLE 2: BASIC DEFINITIONS OF THE HT70X LEDS PATTERN ......................................................................... 10

TABLE 3: ADVANCED DEFINITIONS OF THE HT70X LEDS PATTERN .................................................................. 11

TABLE 4: HT70X SOFTWARE FEATURES ........................................................................................................ 13

TABLE 5: HT70X HARDWARE AND TECHNICAL SPECIFICATIONS ........................................................ 15

TABLE 6: HT70X IVR MENU DEFINITIONS ...................................................................................................... 16

TABLE 7: HT70X CALL FEATURES .................................................................................................................. 22

TABLE 8: BASIC SETTINGS ........................................................................................................................ 26

TABLE 9: STATUS PAGE ............................................................................................................................. 28

TABLE 10: ADVANCED SETTINGS ............................................................................................................. 30

TABLE 11: ACCOUNT SETTINGS ...................................................................................................................... 35

TABLE 12: HT704 FXS PORTS SETTINGS ...................................................................................................... 44

CONFIGURATION GUI INTERFACE EXAMPLES

HT70X USER MANUAL

(http://www.grandstream.com/products/ht_series/ht701/documents/ht70x_gui.zip)

1. SCREENSHOT OF ADVANCED USER CONFIGURATION PAGE

2. SCREENSHOT OF BASIC SETTINGS CONFIGURATION PAGE

3. SCREENSHOT OF FXS PORT CONFIGURATION

4. SCREENSHOT OF STATUS PAGE

5. SCREENSHOT OF LOGIN PAGE

6. SCREENSHOT OF REBOOT PAGE

7. SCREENSHOT OF REBOOTING PAGE

FIRMWARE VERSION 1.0.3.1 HT70X USER MANUAL Page 5 of 52

GNU GPL INFORMATION

HT70X firmware contains third-party software licensed under the GNU General Public License (GPL).

Grandstream uses software under the specific terms of the GPL. Please see the GNU General Public

License (GPL) for the exact terms and conditions of the license.

Grandstream GNU GPL related source code can be downloaded from Grandstream web site from:

http://www.grandstream.com/support/faq/gnu_gpl .

FIRMWARE VERSION 1.0.3.1 HT70X USER MANUAL Page 6 of 52

CHANGE LOG

This section documents significant changes from previous versions of HT70X user manuals. Only major

new features or major document updates are listed here. Minor updates for corrections or editing are not

documented here.

CHANGES FROM 1.0.1.6 USER MANUAL

 Added the option to enable/disable hook flash [Enable Hook Flash]

 Removed firmware key from Advanced Setting page

CHANGES FROM 1.0.0.18 USER MANUAL

 Added ability to configure delay for the off hook auto dial [Offhook Auto-Dial Delay]

 Added display of gs_cpe version in status page [CPE]

 Added a configuration parameter to overdrive User-Agent header [Use SIP User-Agent Header]

 Added [CPE SSL Certificate] and [CPE SSL Private Key] in "Advanced" web page

 Added an option to Enable/Disable each FXS Port [Enable Ports]

 Split function Use Random Port into [Use Random SIP Port] and [Use Random RTP Port] in all content

FIRMWARE VERSION 1.0.3.1 HT70X USER MANUAL Page 7 of 52

WELCOME

Thank you for purchasing Grandstream’s HT70X, the affordable, feature rich Analog Telephone Adaptor.

Grandstream HandyTone70X is a new addition to the popular HandyTone ATA product family. It features

the rich audio quality, a broad range of voice codecs, and functionality including one independent SIP

account per FXS port.

This manual will help you learn how to operate and manage your HandyTone70X Analog Telephone

Adaptor and make the best use of its many upgraded features including simple and quick installation, 3-

way conferencing, direct IP-IP Calling, and new provisioning support among other features. This HT70X

is very easy to manage and configure, and is specifically designed to be an easy to use and affordable

VoIP solution for both the residential user and the teleworker.

SAFETY COMPLIANCES

The HT70X phone complies with FCC/CE and various safety standards. The HT70X power adaptor is

compliant with UL standard. Only use the universal power adapter provided with the HT70X package.

The manufacturer’s warranty does not cover damages to the phone caused by unsupported power

adaptors.

WARRANTY

If you purchased your HT70X from a reseller, please contact the company where you purchased your

device for replacement, repair or refund. If you purchased the product directly from Grandstream, contact

your Grandstream Sales and Service Representative for a RMA (Return Materials Authorization) number

before you return the product. Grandstream reserves the right to remedy warranty policy without prior

notification.

Caution: Changes or modifications to this product not expressly approved by Grandstream, or operation

of this product in any way other than as detailed by this User Manual, could void your manufacturer

warranty. Please do not use a different power adaptor with the HT70X as it may cause damage to the

products and void the manufacturer warranty.

FIRMWARE VERSION 1.0.3.1 HT70X USER MANUAL Page 8 of 52

 This document contains links to HT70X GUI Interfaces. Please download these examples for

your reference here:

http://www.grandstream.com/products/ht_series/ht701/documents/ht70x_gui.zip

 This document is subject to change without notice. The latest electronic version of this user

manual is available for download at:

http://www.grandstream.com/products/ht_series/ht701/documents/ht70x_usermanual_english.pdf

Reproduction or transmittal of the entire or any part, in any form or by any means, electronic or print, for

any purpose is not permitted without the express written permission of Grandstream Networks, Inc.

FIRMWARE VERSION 1.0.3.1 HT70X USER MANUAL Page 9 of 52

CONNECT YOUR HT70X

Connecting the HT70X is easy. Before you begin, please verify the contents of the HT70X package.

EQUIPMENT PACKAGING

The HT70X ATA package contains:

 One HT70X Main Case

 One Universal Power Adaptor

 One Ethernet Cable

 One Vertical Stand (Only on HT702 and HT704 Packages)

CONNECTING THE HT70X

The HT70X is designed for easy configuration and easy installation. Configure the HT70X following the

directions in the Configuration section of this manual.

1. Insert a standard RJ11 telephone cable into the Phone port and connect the other end of the

telephone cable to a standard touch-tone analog telephone.

2. Insert the Ethernet cable into the Internet or LAN port of the HT70X and connect the other end of

the Ethernet cable to an uplink port (a router or a modem, etc.)

3. Insert the power adapter into the HT70X and connect it to a wall outlet.

The HT70X Analog Telephone Adaptor is an all-in-one VoIP integrated device designed to be a total

solution for networks providing VoIP services. The HT70X VoIP features and functions are available

using a regular analog telephone.

FIRMWARE VERSION 1.0.3.1 HT70X USER MANUAL Page 10 of 52

HT702 HT704

FIGURE 1: DIAGRAM OF HT70X

TABLE 1: DEFINITIONS OF THE HT70X CONNECTORS

DC 12V

Power adapter connection

Internet Port (RJ-45)

Connect to the internal LAN network. (HT701 Only)

LAN Port (RJ-45)

Connect to the internal LAN network. (HT702 and HT704 Only)

RESET

Factory Reset button: Press for 7 seconds to reset factory default settings.

Phone Port(s) (RJ-11)

FXS port: to be connected to analog phones / fax machines.

There are four (4) LED buttons that help you manage the status of your HandyTone 701, and

there are five (5) LED buttons that help you manage the status of your HandyTone 702 and 704.

TABLE 2: BASIC DEFINITIONS OF THE HT70X LEDS PATTERN

POWER LED

Indicates Power. Remains ON when power is connected

Internet LED

Indicates Access to Internet. Remains ON while there is Access (HT701 and HT702 Only)

Link/Activity LED

Indicates if There is Activity on the Internet Port (HT701 and HT702 Only)

Internet Port

(RJ-45 connector

10/100 Mbps)

Reset

Phone

(RJ-11 FXS Ports)

Power

Supply

(12V;0.5A)

HT-701

Display LEDs

(green)

LAN Port

(RJ-45 connector

10/100 Mbps

with LEDS)

Reset

Power

Supply

(12V;1A)

Phone (RJ-11

FXS Ports)

LAN Port

(RJ-45 connector

10/100 Mbps )

Reset

Power

Supply

(12V;1A)

Phone (RJ-11

FXS Ports)

Display LED’s (green)

FIRMWARE VERSION 1.0.3.1 HT70X USER MANUAL Page 11 of 52

PHONE LED

Indicate status of the respective FXS Ports-PHONE on the back panel

Unregistered – OFF

Registered and Available – ON (Solid Green)

Off-Hook / Busy – Blinking every second

Slow blinking FXS LEDs indicates voicemail

NOTE: All LEDs display green when ON

TABLE 3: ADVANCED DEFINITIONS OF THE HT70X LEDS PATTERN

LED-01

Device has normal power

Power

ON

LED-02

Power Error: Power is removed from the device or power

supply with improper voltage is plugged in

Power

OFF

LED-03

Line X is registered normally to the sip providers network

and is ready to make a call

Phone

ON

LED-04

Voice mail waiting for Line X

Phone

1sec ON / 3sec OFF

LED-05

Device has normal WAN connection and has obtained IP

address

Internet

ON

LED-06

Internet link error: Device is powered up and ready to

connect to the Internet but the WAN/INTERNET port is

down

Internet

OFF

LED-07

Internet DHCP Error: Device is properly connected but it is

unable to retrieve an IP address from the device it is

connected to

Internet

0.25sec ON/ 0.25sec OFF

LED-08

Line Registration failed: Device is properly setup, can

connect to provider's network, but cannot register to

provider's SIP proxy (no 200 OK)

Phone

OFF

LED-09

Device is connected (has physical data link) but there are

incorrect network settings typically associated with PPPoE

connection failure

Internet

0.25sec ON/ 0.25sec OFF

LED-10

Hazardous potential test failed: Hazardous AC or DC

voltage is present on the tip and ring or both signals of

phone line X

Phone

0.25sec ON/ 0.25sec OFF

LED-11

Foreign electro Motive Force (EMF) Test fail. Foreign

voltage is present on the tip, ring or both signals of phone

line. Device has detected additional external Phone

voltage on the FXS phone line.

Phone

0.25sec ON/ 0.25sec OFF

LED-12

Resistive fault test failed. Either tip or ring is shorted to

ground or they are shorted to each other.

Phone

0.25sec ON/ 0.25sec OFF

FIRMWARE VERSION 1.0.3.1 HT70X USER MANUAL Page 12 of 52

LED-13

Receiver off hook test fail. One or more phones are off

hook on phone line during test.

Phone

0.25sec ON/ 0.25sec OFF

LED-14

REN test failed – high REN detected. Too many parallel

phones connected to phone line X

Phone

0.25sec ON/ 0.25sec OFF

LED-15

Line is active

Phone

1 sec ON/ 1 sec OFF

LED-16

Line inactive

Phone

ON

LED-17

During Provisioning Stage*

Internet /

Phone

0.2sec ON/ 0.2sec OFF

LED-18

During Firmware Recovery Stage*

Internet /

Phone

0.4sec ON/ 0.4sec OFF

*Note: In Provisioning and Firmware Recovery Stage, the power LED is Steady ON.

FIGURE 2: HT70X CONNECTION DIAGRAM

Internet

ADSL/Cable

Modem Ethernet

LAN

FXS

Fax

Cordless

Phone

Analog

Phone

HT701/702/704

FIRMWARE VERSION 1.0.3.1 HT70X USER MANUAL Page 13 of 52

HT70X FEATRUES

The HT70X is a full feature voice and fax-over IP device that offers a high-level of integration including a

10M/100Mbps network port and one FXS telephone port, market-leading sound quality, rich

functionalities, and a compact and lightweight design. The VoIP network signaling protocol supported is

SIP. The HT70X is fully compatible with SIP industry standard and can interoperate with many other SIP

compliant devices and software on the market. Moreover, it supports comprehensive voice codecs

including G.711 (a/µ-law), G.723.1, G.726-32, G.729 and iLBC.

SOFTWARE FEATURES OVERVIEW

 Supports Voice Codecs:

 G.711 (a/µ-law), G.723.1, G.726-32, G.729 and iLBC.

 T.38 Fax

 Comprehensive Dial Plan support for Outgoing calls.

 G.168 Echo Cancellation

 Voice Activation Detection (VAD), Comfort Noise Generation (CNG), and Packet Loss

Concealment (PLC)

 Supports PSTN/PBX analog telephone sets

TABLE 4: HT70X SOFTWARE FEATURES

HT 701

HT 702

HT 704

Telephone Interfaces

1 FXS ports

2 FXS ports

4 FXS ports

SIP Provisioning

1 Sip Account, 1 Profile

2 Sip Accounts, 2 Profiles

4 Sip Accounts, 2 Profiles

Number of

Concurrent Calls

1 Concurrent Call

2 Concurrent Calls

4 Concurrent Calls

Voice over Packet

Capabilities

Voice Activity Detection (VAD) with CNG (comfort noise generation) and PLC (packet loss

concealment), Dynamic Jitter Buffer, Modem detection & auto-switch to G.711, Packetized

Voice Protocol Unit (supports RTP/RTCP protocol), G.168 compliant Echo Cancellation,

LEC (line echo cancellation) with NLP, Asymmetric RTP stream

Voice Compression

G.711 + Annex I (PLC), Annex II (VAD/CNG format) encoder and decoder, G.723.1, G.726-

32(ADPCM), G.729, iLBC, G.726-32 provides proprietary VAD, CNG, and signal power

estimation, Voice Play Out unit (reordering, fixed and adaptive jitter buffer, clock

FIRMWARE VERSION 1.0.3.1 HT70X USER MANUAL Page 14 of 52

synchronization), AGC (automatic gain control), Status output, Decoder controlling via voice

packet header

DHCP Server/Client

Yes, DHCP Client only

Telnet Server

Yes

Fax over Ip

T.38 compliant Group 3 Fax Relay up to 14.4kpbs and auto-switch to G.711 for Fax Pass-

through, Fax Datapump V.17, V.19, V.27ter, V.29 for T.38 fax relay

QoS

Diffserve, TOS, 802.1 P/Q VLAN tagging

Transport Protocol

RTP/RTCP

DTMF Method

Flexible DTMF transmission method, user interface of In-audio, RFC2833, and/or SIP Info

IP Signaling

SIP (RFC 3261)

Provisioning

TFTP, HTTP, HTTPS, TR-069, XML

Control

TLS/SIPS , SIP over TCP/TLS

Device Management

Web interface or via secure encrypted AES or non-encrypted central configuration file for

mass deployment using Grandstream binary file or xml format. Auto/manual provisioning

system or via built-in IVR.

NAT-friendly remote software upgrade (via TFTP/HTTP/HTTPS) for deployed devices

including behind firewall/NAT. Syslog support. Full support of TR-069 management protocol

and Telnet access.

Dial Plan

Yes

Caller ID

Bellcore Type 1 & 2, ETSI, BT, NTT, and DTMF-based CID

Call Handling

Features

Caller ID display or block, Call waiting caller ID, Call waiting/flash, Call transfer, hold,

forward, 3-way conferencing, message waiting, Do-Not-Disturb (DND), call-return service

FIRMWARE VERSION 1.0.3.1 HT70X USER MANUAL Page 15 of 52

HARDWARE SPECIFICATION

The table below lists the Hardware and Technical specification of HT70X.

TABLE 5: HT70X HARDWARE AND TECHNICAL SPECIFICATIONS

HT701

HT702

HT704

Telephone

Interfaces

1 RJ11 FXS port

2 RJ11 FXS ports

4 RJ11 FXS ports

Network

Interface

1 RJ45 10/100 Mb Base-TX, Full Duplex

1 RJ45 10/100 Mb Base-TX,

Full Duplex port with

connectivity LEDs

LED Indicators

POWER, INTERNET,

LINK/ACTIVITY, PHONE

POWER, INTERNET,

LINK/ACTIVITY,

PHONE1, PHONE2

POWER, PHONE1, PHONE2,

PHONE3, PHONE4

Factory Reset

Button

Yes

Universal

Switching

Power Adaptor

Input: 100–240 VAC/50-60 Hz 0.18A Max

Output: 12VDC, 0.5A, UL certified

Input: 100–240 VAC/50-60 Hz

0.18A Max

Output: 12VDC, 1A, UL certified

Environmental

Operational: 32

o

–104

o

F or 0

o

–40

o

C

Storage: 14

o

–140

o

F or -10

o

–60

o

Humidity: 10–90% Non-condensing

Dimensions

(H x W x D)

26 x 65 x 86mm

28 x 115 x 75mm

Short Haul Loop

5REN, Up to 1Km on 24 AWG

wire

3REN: Up to 1Km on 24 AWG line

Polarity

Reversal / Wink

Yes

EMC

FCC part15 Class B, EN55022, EN55024, CISPR22, and CISPR24

Safety

EN60950-1 & UL60950-1 (UL only for PSU)

Compliance

FIRMWARE VERSION 1.0.3.1 HT70X USER MANUAL Page 16 of 52

BASIC OPERATIONS

UNDERSTANDING HT70X VOICE PROMPT

HT70X has a built-in voice prompt menu for simple device configuration. The IVR menu and the LED

button work with any of the FXS port. Pick up the handset and dial “***” to use the IVR menu.

TABLE 6: HT70X IVR MENU DEFINITIONS

MENU

VOICE PROMPT

OPTIONS

Main Menu

“Enter a Menu Option”

Press “*” for the next menu option

Press “#” to return to the main menu

Enter 01-05, 07,10, 13-17,47 or 99 menu options

01

“DHCP Mode”,

“Static IP Mode”

Press “9” to toggle the selection

If using “Static IP Mode”, configure the IP address information using

menus 02 to 05.

If using “Dynamic IP Mode”, all IP address information comes from

the DHCP server automatically after reboot.

02

“IP Address “ + IP address

The current WAN IP address is announced

If using “Static IP Mode”, enter 12 digit new IP address. You need to

reset the HT for the new IP address to take Effect.

03

“Subnet “ + IP address

Same as menu 02

04

“Gateway “ + IP address

Same as menu 02

05

“DNS Server “ + IP address

Same as menu 02

07

Preferred Vocoder

Press “9” to move to the next selection in the list:

 PCM U / PCM A

 iLBC

 G-726

 G-723

 G-729

10

“MAC Address”

Announces the Mac address of the unit.

13

Firmware Server IP

Address

Announces current Firmware Server IP address. Enter 12 digit new

IP address.

14

Configuration Server IP

Address

Announces current Config Server Path IP address. Enter 12 digit

new IP address.

15

Upgrade Protocol

Upgrade protocol for firmware and configuration update. Press “9” to

FIRMWARE VERSION 1.0.3.1 HT70X USER MANUAL Page 17 of 52

toggle between TFTP / HTTP / HTTPS

16

Firmware Version

Firmware version information.

17

Firmware Upgrade

Firmware upgrade mode. Press “9” to toggle among the following

three options:

- always check

- check when pre/suffix changes

- never upgrade

47

“Direct IP Calling”

Enter the target IP address to make a direct IP call, after dial tone.

(See “Make a Direct IP Call”.)

86

Voice Mail

Number of Voice Mails

99

“RESET”

Press “9” to reboot the device

Enter MAC address to restore factory default setting

(See Restore Factory Default Setting section)

“Invalid Entry”

Automatically returns to main menu

“Device not registered”

This prompt will be played immediately after off hook If the device is

not register and the option “Outgoing Call without Registration” is in

NO

Five Success Tips when using the Voice Prompt

1. “*” shifts down to the next menu option

2. “#” returns to the main menu

3. “9” functions as the ENTER key in many cases to confirm or toggle an option

4. All entered digit sequences have known lengths - 2 digits for menu option and 12 digits for IP

address. For IP address, add 0 before the digits if the digits are less than 3 (i.e. - 192.168.0.26

should be key in like 192168000026. No decimal is needed).

5. Key entry cannot be deleted but the phone may prompt error once it is detected

FIRMWARE VERSION 1.0.3.1 HT70X USER MANUAL Page 18 of 52

PLACING A PHONE CALL

PHONE OR EXTENSION NUMBERS

1. Dial the number directly and wait for 4 seconds (Default “No Key Entry Timeout”); or

2. Dial the number directly and press # (Use # as dial key” must be configured in web configuration).

Examples:

1. Dial an extension directly on the same proxy, (e.g. 1008), and then press the # or wait for 4 seconds.

2. Dial an outside number (e.g. (626) 666-7890), first enter the prefix number (usually 1+ or international

code) followed by the phone number. Press # or wait for 4 seconds. Check with your VoIP service

provider for further details on prefix numbers.

DIRECT IP CALLS

Direct IP calling allows two parties, that is, a FXS Port with an analog phone and another VoIP Device, to

talk to each other in an ad hoc fashion without a SIP proxy.

Elements necessary to completing a Direct IP Call:

1. Both HT70X and other VoIP Device, have public IP addresses, or

2. Both HT70X and other VoIP Device are on the same LAN using private IP addresses, or

3. Both HT70X and other VoIP Device can be connected through a router using public or private IP

addresses (with necessary port forwarding or DMZ).

HT70X supports two ways to make Direct IP Calling:

Using IVR

1. Pick up the analog phone then access the voice menu prompt by dial “***”

2. Dial “47” to access the direct IP call menu

3. Enter the IP address after the dial tone and voice prompt “Direct IP Calling”

Using Star Code

1. Pick up the analog phone then dial “*47”

2. Enter the target IP address.

Note: NO dial tone will be played between step 1 and 2.

FIRMWARE VERSION 1.0.3.1 HT70X USER MANUAL Page 19 of 52

Destination ports can be specified using “*” (encoding for “:”) followed by the port number.

Examples of Direct IP Calls:

a) If the target IP address is 192.168.0.160, the dialing convention is

*47 or Voice Prompt with option 47, then 192*168*0*160.

followed by pressing the “#” key if it is configured as a send key or wait 4 seconds. In this case,

the default destination port 5060 is used if no port is specified.

b) If the target IP address/port is 192.168.1.20:5062, then the dialing convention would be:

*47 or Voice Prompt with option 47, then 192*168*0*160*5062 followed by pressing the “#” key

if it is configured as a send key or wait for 4 seconds.

NOTE: When completing direct IP call, the “Use Random SIP/RTP Port” should set to “NO”. You

cannot make direct IP calls between FXS1 to FXS2 since they are using same IP.

CALL HOLD

Place a call on hold by pressing the “flash” button on the analog phone (if the phone has that button).

Press the “flash” button again to release the previously held Caller and resume conversation. If no “flash”

button is available, use “hook flash” (toggle on-off hook quickly). You may drop a call using hook flash.

CALL WAITING

Call waiting tone (3 short beeps) indicates an incoming call, if the call waiting feature is enabled. Toggle

between incoming call and current call by pressing the “flash” button. First call is placed on hold. Press

the “flash” button to toggle between two active calls.

CALL TRANSFER

BLIND TRANSFER

Assume that call Caller A and B are in conversation. A wants to Blind Transfer B to C:

3. Caller A presses FLASH on the analog phone to hear the dial tone.

4. Caller A dials *87 then dials caller C’s number, and then # (or wait for 4 seconds)

5. Caller A will hear the confirm tone. Then, A can hang up.

NOTE: “Enable Call Feature” must be set to “Yes” in web configuration page.

FIRMWARE VERSION 1.0.3.1 HT70X USER MANUAL Page 20 of 52

Caller A can place a call on hold and wait for one of three situations:

1. A quick confirmation tone (similar to call waiting tone) followed by a dial-tone. This indicates the

transfer is successful (transferee has received a 200 OK from transfer target). At this point,

Caller A can either hang up or make another call.

2. A quick busy tone followed by a restored call (on supported platforms only). This means the

transferee has received a 4xx response for the INVITE and we will try to recover the call. The

busy tone is just to indicate to the transferor that the transfer has failed.

3. Continuous busy tone. The phone has timed out.

Note: continuous busy tone does not indicate the transfer has been successful, nor does it indicate

the transfer has failed. It often means there was a failure to receive second NOTIFY – check

firmware for most recent release.

ATTENDED TRANSFER

Assume that Caller A and B are in conversation. Caller A wants to Attend Transfer B to C:

1. Caller A presses FLASH on the analog phone for dial tone.

2. Caller A then dials Caller C’s number followed by # (or wait for 4 seconds).

3. If Caller C answers the call, Caller A and Caller C are in conversation. Then A can hang up to

complete transfer.

4. If Caller C does not answer the call, Caller A can press “flash” to resume call with Caller B.

NOTE: When Attended Transfer fails and A hangs up, the HT70X will ring back user A to remind A that B

is still on the call. A can pick up the phone to resume conversation with B.

3-WAY CONFERENCING

The HT701/702/704 supports Bellcore style 3-way Conference.

Instructions for 3-way conference:

Assume that call party A and B are in conversation. Caller A(HT70X) wants to bring third Caller C into

conference:

1. A presses FLASH (on the analog phone, or Hook Flash for old model phones) to get a dial tone.

2. A dials C’s number then # (or wait for 4 seconds).

Page is loading ...

Grandstream Networks HT701 User manual

This manual is also suitable for

Grandstream Networks HT701 User manual

Related papers

Other documents