Niles Audio SPS-6 User manual

Niles Audio
Brand
Niles Audio
Model
SPS-6
Category
Soundbar speakers
Type
User manual

Niles Audio SPS-6 is a speaker selection system that enables you to connect up to six pairs of speakers to your stereo receiver or amplifier and play one pair, any combination of pairs or all pairs at once. It features individual runs of 2-conductor speaker wire, and connectors accommodate wire sizes 14-22 gauge. The SPS-6 has a protection switch that safeguards your receiver or amplifier even with all 6 pairs of speakers playing. It is compatible with 4, 6 or 8 ohm speaker systems and has self-cleaning, silver-plated switch contacts for years of trouble-free use.

Niles Audio SPS-6 is a speaker selection system that enables you to connect up to six pairs of speakers to your stereo receiver or amplifier and play one pair, any combination of pairs or all pairs at once. It features individual runs of 2-conductor speaker wire, and connectors accommodate wire sizes 14-22 gauge. The SPS-6 has a protection switch that safeguards your receiver or amplifier even with all 6 pairs of speakers playing. It is compatible with 4, 6 or 8 ohm speaker systems and has self-cleaning, silver-plated switch contacts for years of trouble-free use.

• Pre-printed Room Labels
are included for easy identi-
fication of speaker ON/OFF
buttons.
• Isolated left and right chan-
nel ground returns make
the SPS-6 compatible with
all types of amplifiers.
• May be used with 4, 6 or 8
ohm speaker systems.
• Self-cleaning, silver-plated
switch contacts assure
years of trouble free use.
• 100% tested, electronically
and acoustically, for fre-
quency response, distortion
and power handling.
• Protection circuit safeguards
your receiver or amplifier.
• Spring-loaded push termi-
nal connectors accommo-
date up to 14 gauge wire or
"pins", making the SPS-6
compatible with most high
definition speaker cables.
• Ten year parts and labor
warranty.
FEATURES & BENEFITS
FEATURES & BENEFITS
INTRODUCTION
SSPPSS--66 SPEAKER SELECTION SYSTEM
PROTECTION
132 456
NILES
NILES TECHNICAL DATA SHEET
SPECIFICATIONS
Audio Power Handling
100 watts/channel con-
tinuous music power
Mounting
Table-top component
Frequency Response
+0 dB, -0 dB (flat) from
20 Hz to 20 kHz
Wiring Requirements
Individual runs of
2-conductor speaker
wire. Connectors
accommodate wire
sizes 14-22 gauge. 16
gauge recommended
Overall Dimensions
11-1/4" wide x 2" high
x 6-3/4" deep
Weight
2-1/4 lb.
SPS-6
Speaker Selection System
B LENDING H IGH F IDELITY
AND
A RCHITECTURE
®
INTRODUCTION
The SPS-6 enables you to connect up to six pairs of speakers to
your stereo receiver or amplifier and play one pair, any combi-
nation of pairs or all pairs at once.
CONTINUED OTHER SIDE ➯
SPEAKER 2 SPEAKER 1SPEAKER 4 SPEAKER 3SPEAKER 5SPEAKER 6
LR
AMPLIFIER
LRLR
++ ++
-- --
++ ++
-- --
LRLR
++ ++
-- --
LRLR
++ ++
-- --
Niles Audio
Corporation,Inc.
Miami, Florida USA
NILES
Recessed areas for
custom room labels
Simple push-button
operation
Connect up to six
pairs of speakers
Spring-loaded push
connectors
Attractive low-profile design
Protection switch safeguards your
receiver or amplifier even with all
6 pairs of speakers playing
Connections
If your amplifier or receiver
has "A" and "B" speaker pair
outputs, connect the SPS-6 to
the "A" points. Do not
con-
nect anything to "B". This
will prevent the amplifier or
receiver from driving an
unusually low impedance
load.
Using the SPS-6 with Tube
Type Amplifiers
Virtually all tube amplifiers
must have a load connected
at all times. If the amplifier to
be connected to the SPS-6 is
a tube amplifier, be sure to
always have at least one pair
of speakers switched on at all
times. An alternative is to per-
manently connect a 150 ohm,
5 watt resistor across the tube
amplifier's output in parallel
with the SPS-6.
Impedance Matching
You will need to activate the
SPS-6's PROTECTION button
whenever the overall system
impedance might fall below
4 ohms.
TUNER 94.9
15
SPEAKER 2 SPEAKER 1SPEAKER 4 SPEAKER 3SPEAKER 5SPEAKER 6
LR
AMPLIFIER
LRLR
++ ++
-- --
++ ++
-- --
LRLR
++ ++
-- --
LRLR
++ ++
-- --
Niles Audio
Corporation, Inc.
Miami, Florida USA
NILES
150
150
SPEAKER 2 SPEAKER 1SPEAKER 4 SPEAKER 3SPEAKER 5SPEAKER 6
LR
AMPLIFIER
LRLR
++ ++
-- --
++ ++
-- --
LRLR
++ ++
-- --
LRLR
++ ++
-- --
Niles Audio
Corporation, Inc.
Miami, Florida USA
NILES
TOOLS REQUIRED
• 1/8" Standard Slotted
Screwdriver
• Wire Stripper
MODEL SPS-6 Speaker Selection System (continued)
NILES AUDIO CORPORATION
12331 S.W. 130 STREET MIAMI, FLORIDA 33186
TEL: (305) 238-4373 FAX: (305) 238-0185 INTERNET: www.nilesaudio.com
©1999 Niles Audio Corporation. Niles, the Niles logo and Blending High Fidelity and Architecture are registered trademarks of Niles Audio Corporation. Printed in USA DS00098A
Connections
Receiver
Speaker Pairs
Protecting a Tube Amplifier
Tube Amplifier
150 ohm, 5 watt Resistors
APPLICATION NOTES
APPLICATION NOTES
When playing the following speakers:
1 or 2 pair of 8-ohm speakers
3 or more pairs of 8-ohm speakers
1 pair of 4-ohm speaker
2, or more pairs of 4-ohm speakers
Any combination of 4 and 8 ohm speakers
The Protection button should be:
OFF
ON
OFF
ON
ON
CEDIA
CUSTOM
ELECTRONIC
DESIGN &
INSTALLATION
ASSOCIATION
CHARTER MEMBER
  • Page 1 1
  • Page 2 2

Niles Audio SPS-6 User manual

Niles Audio
Brand
Niles Audio
Model
SPS-6
Category
Soundbar speakers
Type
User manual

Niles Audio SPS-6 is a speaker selection system that enables you to connect up to six pairs of speakers to your stereo receiver or amplifier and play one pair, any combination of pairs or all pairs at once. It features individual runs of 2-conductor speaker wire, and connectors accommodate wire sizes 14-22 gauge. The SPS-6 has a protection switch that safeguards your receiver or amplifier even with all 6 pairs of speakers playing. It is compatible with 4, 6 or 8 ohm speaker systems and has self-cleaning, silver-plated switch contacts for years of trouble-free use.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents