Edelbrock 91147 User manual

Edelbrock
Brand
Edelbrock
Model
91147
Category
Cable interface/gender adapters
Type
User manual

Edelbrock 91147 is a USB to Serial communications adapter cable. It is used to convert a Laptop or PC USB port to a 9-pin RS232 serial communications connector. This item is included in all QwikData Data Acquisition and Edelbrock EFI kits.

The Edelbrock 91147 allows you to connect your laptop or PC to a serial device, such as a data acquisition system or an EFI system. The cable is plug-and-play, so you don't need to install any drivers.

The Edelbrock 91147 is a versatile cable that can be used for a variety of applications. It is perfect for use with Edelbrock QwikData or EFI systems, but it can also be used with other data acquisition or EFI systems.

Edelbrock 91147 is a USB to Serial communications adapter cable. It is used to convert a Laptop or PC USB port to a 9-pin RS232 serial communications connector. This item is included in all QwikData Data Acquisition and Edelbrock EFI kits.

The Edelbrock 91147 allows you to connect your laptop or PC to a serial device, such as a data acquisition system or an EFI system. The cable is plug-and-play, so you don't need to install any drivers.

The Edelbrock 91147 is a versatile cable that can be used for a variety of applications. It is perfect for use with Edelbrock QwikData or EFI systems, but it can also be used with other data acquisition or EFI systems.

Catalog #91147
Rev. 4/08 - AJ/mc
©2008 Edelbrock Corporation
Brochure #63-91147
USB PORT TO SERIAL PORT ADAPTER CABLE
For Use with Edelbrock QwikData or EFI Systems,
As Well As Other Data Acquisition or EFI Systems
Catalog #91147
INSTALLATION INSTRUCTIONS
®
PLEASE study these instructions carefully before beginning this installation. If you have any questions, please call our Technical Hotline at:
1-800-416-8628, 7:00 am - 5:00 pm, Pacific Standard Time, Monday through Friday or e-mail us at [email protected].
DESCRIPTION: This is a USB to Serial communications adapter cable. It is used to convert a
Laptop or PC USB port to a 9-pin RS232 serial communications connector. This item is included
in all QwikData Data Acquisition and Edelbrock EFI kits. Software drivers are included on the
supplied CD.
KIT CONTENTS
❑ 1 USB-to-Serial Adapter Cable
SYSTEM REQUIREMENTS
Hardware – A USB-enabled PC or Laptop
Software – Microsoft
®
Windows 98SE/ME/2000/XP
INSTALLATION: The drivers for the USB-Serial Port adapter cable are located on the supplied CD.
Microsoft
®
Windows Installation
Insert the disc into your CD-ROM drive and click on
“Install USB-to-DB9”
then follow the onscreen prompts.
NOTE: You may use the same program to un-install the driver if desired. Run the “PL-2303 Driver Installer” program again and
follow the prompts to un-install the driver.
TROUBLESHOOTING: If the adapter is not communicating after installation of the driver, follow the troubleshooting suggestions below.
• Many serial devices will not operate on a COM port higher than 4. If the COM port is higher than 4, change it to a lower number using the Device
Properties.
• To change the assigned COM number, go to the Start menu, click Control Panel then System. Select the Hardware tab and then Device Manager.
Select the category
“Ports (COM & LPT)”
and right click the device
“USB-to-Serial (COM x)”
(Or a similar name.
“X”
represents the assigned COM
number). Click the Port Settings tab, then the Advanced button. A box will be in the lower left corner to assign a different COM port to the adapter.
NOTE: This procedure applies only to Windows 98SE, ME, 2000, and XP
.
Edelbrock Corporation • 2700 California St. • Torrance, CA 90503
Tech Line: 1-800-416-8628 • E-Mail: [email protected]
  • Page 1 1

Edelbrock 91147 User manual

Edelbrock
Brand
Edelbrock
Model
91147
Category
Cable interface/gender adapters
Type
User manual

Edelbrock 91147 is a USB to Serial communications adapter cable. It is used to convert a Laptop or PC USB port to a 9-pin RS232 serial communications connector. This item is included in all QwikData Data Acquisition and Edelbrock EFI kits.

The Edelbrock 91147 allows you to connect your laptop or PC to a serial device, such as a data acquisition system or an EFI system. The cable is plug-and-play, so you don't need to install any drivers.

The Edelbrock 91147 is a versatile cable that can be used for a variety of applications. It is perfect for use with Edelbrock QwikData or EFI systems, but it can also be used with other data acquisition or EFI systems.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers