Philips LX3600D User manual

Philips
Brand
Philips
Model
LX3600D
Category
Home cinema systems
Type
User manual

This manual is also suitable for

1
DVD VIDEO
DIGITAL SURROUND SYSTEM
LX
3600D
LX
3600D
001-041-LX36-22-Eng 21/08/2003, 9:43 AM1
2
Important notes for users in the
U.K.
Mains plug
This apparatus is fitted with an approved 13
Amp plug. To change a fuse in this type of plug
proceed as follows:
1 Remove fuse cover and fuse.
2 Fix new fuse which should be a BS1362 5 Amp,
A.S.T.A. or BSI approved type.
3 Refit the fuse cover.
If the fitted plug is not suitable for your socket
outlets, it should be cut off and an appropriate
plug fitted in its place.
If the mains plug contains a fuse, this should
have a value of 5 Amp. If a plug without a fuse
is used, the fuse at the distribution board
should not be greater than 5 Amp.
Note: The severed plug must be disposed of to
avoid a possible shock hazard should it be
inserted into a 13 Amp socket elsewhere.
How to connect a plug
The wires in the mains lead are coloured with
the following code: blue = neutral (N),
brown = live (L).
As these colours may not correspond with the
colour markings identifying the terminals in
your plug, proceed as follows:
– Connect the blue wire to the terminal
marked N or coloured black.
– Connect the brown wire to the terminal
marked L or coloured red.
– Do not connect either wire to the earth
terminal in the plug, marked E (or e) or
coloured green (or green and yellow).
Before replacing the plug cover, make certain
that the cord grip is clamped over the sheath
of the lead - not simply over the two wires.
Copyright in the U.K.
Recording and playback of material may
require consent. See Copyright Act 1956 and
The Performer’s Protection Acts 1958 to 1972.
Norge
Typeskilt finnes på apparatens underside.
Observer: Nettbryteren er sekundert
innkoplet. Den innebygde netdelen er
derfor ikke frakoplet nettet så lenge
apparatet er tilsluttet nettkontakten.
For å redusere faren for brann eller elektrisk
støt, skal apparatet ikke utsettes for regn eller
fuktighet.
Italia
DICHIARAZIONE DI CONFORMITA’
Si dichiara che l’apparecchio LX3600D, Philips
risponde alle prescrizioni dell’art. 2 comma 1 del
D.M. 28 Agosto 1995 n. 548.
Fatto a Eindhoven
Philips Consumer Electronics
Philips, Glaslaan 2
5616 JB Eindhoven, The Netherlands
CAUTION
Use of controls or adjustments or
performance of procedures other than
herein may result in hazardous
radiation exposure or other unsafe
operation.
VAROITUS
Muiden kuin tässä esitettyjen
toimintojen säädön tai asetusten
muutto saattaa altistaa vaaralliselle
säteilylle tai muille vaarallisille
toiminnoille.
001-041-LX36-22-Eng 21/08/2003, 9:43 AM2
3
3
CAUTION
VISIBLE AND INVISIBLE LASER
RADIATION WHEN OPEN AVOID
EXPOSURE TO BEAM
ADVARSEL
SYNLIG OG USYNLIG
LASERSTRÅLING VED ÅBNING
UNDGÅ UDSÆTTELSE FOR STRÅLING
VARNING
SYNLIG OCH OSYNLIG
LASERSTRÅLNING NÄR DENNA DEL
ÄR ÖPPNAD BETRAKTA EJ STRÅLEN
VARO!
AVATTAESSA OLET ALTTIINA
NÄKYVÄLLE JA NÄKYMÄTTÖMÄLLE
LASER SÄTEILYLLE. ÄLÄ KATSO
SÄTEESEEN
VORSICHT
SICHTBARE UND UNSICHTBARE
LASERSTRAHLUNG WENN
ABDECKUNG GEÖFFNET NICHT DEM
STRAHL AUSSETSEN
ATTENTION
RAYONNEMENT LASER VISIBLE ET
INVISIBLE EN CAS D’OUVERTURE
EXPOSITION DANGEREUSE AU
FAISCEAU
LASER
Type Semiconductor laser
GaAlAs
Wave length 650 nm (DVD)
780 nm (VCD/CD)
Output Power 7 mW (DVD)
10 mW (VCD/CD)
Beam divergence 60 degree
Manufactured under license from Dolby
Laboratories. “Dolby”, “Pro Logic” and the
double-D symbol are trademarks of Dolby
Laboratories.
This product complies with the radio
interference requirements of the European
Community.
This DVD/SACD player is in
conformity with the EMC
directive and low-voltage
directive.
001-041-LX36-22-Eng 21/08/2003, 9:43 AM3
4
DK
Advarsel: Usynlig laserstråling ved åbning
når sikkerhedsafbrydere er ude af funktion.
Undgå utsættelse for stråling.
Bemærk: Netafbryderen er sekundært
indkoblet og ofbryder ikke strømmen fra
nettet. Den indbyggede netdel er derfor
tilsluttet til lysnettet så længe netstikket
sidder i stikkontakten.
S
Klass 1 laseraparat
Varning! Om apparaten används på annat
sätt än i denna bruksanvisning specificerats,
kan användaren utsättas för osynlig
laserstrålning, som överskrider gränsen för
laserklass 1.
Observera! Stömbrytaren är sekundärt
kopplad och bryter inte strömmen från
nätet. Den inbyggda nätdelen är därför
ansluten till elnätet så länge stickproppen
sitter i vägguttaget.
SF
Luokan 1 laserlaite
Varoitus! Laitteen käyttäminen
muulla kuin tässä käyttöohjeessa mainitulla
tavalla saattaa altistaa käyttäjän
turvallisuusluokan 1 ylittävälle
näkymättömälle lasersäteilylle.
Oikeus muutoksiin varataan. Laite ei
saa olla alttiina tippu-ja roiskevedelle.
Huom. Toiminnanvalitsin on kytketty
toisiopuolelle, eikä se kytke laitetta irti
sähköverkosta. Sisäänrakennettu verkko-
osa on kytkettynä sähköverkkoon aina
silloin, kun pistoke on pistorasiassa.
001-041-LX36-22-Eng 21/08/2003, 9:43 AM4
5
English
Français
Deutsch
Nederlands
Index
Français ------------------------------------ 42
Deutsch ------------------------------------ 78
Nederlands ------------------------------114
English --------------------------------------- 6
001-041-LX36-22-Eng 21/08/2003, 9:43 AM5
6
English
3139 115 22612
General Information
Supplied accessories ................................... 8
Care and safety information ..................... 8
Connections
Step 1: Set up the speakers ....................... 9
Step 2: Connecting speakers and
subwoofer ..................................................... 9
Step 3: Placing the speakers and
subwoofer ................................................... 10
Step 4: Connecting TV .............................. 11
Using Scart jacks .................................. 11
Using S-Video jack ............................... 11
Step 5: Connecting FM/MW antennas .. 12
Step 6: Connecting the power cord ..... 12
Connections (optional)
Connecting a VCR ..................................... 13
Viewing and listening to the playback..
.................................................................. 13
Using the VCR for recording DVD
playback .................................................. 13
Functional Overview
Main unit and remote control ................ 14
Control buttons available on the
remote only ................................................ 15
Getting Started
Step 1: Inserting batteries into the
remote control .......................................... 16
Using the remote control to operate
the system ............................................. 16
Step 2: Setting the TV ............................... 16
Selecting the colour system that
corresponds to your TV ..................... 17
Step 3: Setting the speakers’ channels .. 17
Step 4: Setting language preference....... 18
Setting the OSD Language ................. 18
Setting the Audio, Subtitle and Disc
Menu Language ..................................... 18
Language Code ..................................... 19
Disc Operations
Playable discs .............................................. 20
Playing discs ................................................ 20
Turning on/off auto Eco Power standby
mode ....................................................... 21
Using the Disc Menu ................................ 21
Basic playback controls ............................ 21
Resuming playback from the last
stopped point (DVD/VCD) ............... 21
Repeat play mode ................................ 22
Repeat A-B ............................................. 22
Zoom ...................................................... 22
Time Search........................................... 23
Special DVD Features .............................. 23
Playing a Title ......................................... 23
Camera Angle........................................ 23
Changing Audio Language................... 23
Subtitles .................................................. 23
Special VCD & SVCD Features .............. 24
Playback Control (PBC)...................... 24
Preview Function.................................. 24
Playing MP3/Picture CD (Kodak, JPEG) ....
....................................................................... 25
General Operation .............................. 25
Playback Selection ................................ 25
Programme playback ........................... 25
Special MP3/JPEG Features ..................... 26
Preview Function (JPEG) .................... 26
Zoom picture (JPEG) .......................... 26
Playback with multi-angles (JPEG) .... 26
Scan Effect (JPEG) ................................ 26
Playback control (MP3) ....................... 26
JPEG and MP3 simultaneous playback .
.................................................................. 26
Contents
001-041-LX36-22-Eng 21/08/2003, 9:43 AM6
7
English
3139 115 22612
DVD Menu Options
Basic Operations ....................................... 27
General Setup Menu................................. 27
Program (not for Picture CD/MP3) .....
............................................................ 27-28
Disc Lock ............................................... 28
Screen Saver .......................................... 28
Audio Setup Menu .................................... 29
Speaker Menu ....................................... 29
Analog Output ...................................... 29
Video Setup Menu..................................... 30
TV Display ............................................. 30
Closed Caption .................................... 31
Picture Setting....................................... 31
Password Setup Menu .............................. 32
Preference Setup Menu ........................... 32
Parental............................................. 32-33
Default Setup ........................................ 33
MP3/JPEG Navigator............................ 33
PBC ......................................................... 33
Tuner Operations
Tuning to radio stations ........................... 34
Presetting radio stations.......................... 34
Using the Plug and Play ....................... 34
Automatic presetting .......................... 35
Manual presetting ................................. 35
Selecting a preset radio station ............. 35
Deleting a preset radio station ......... 35
Contents
Sound and Volume Controls
Sound Control ........................................... 36
Selecting surround sound................... 36
Selecting digital sound effects............ 36
Volume Control ......................................... 36
Other Functions
Setting the Sleep timer ............................ 37
Switching on/off ......................................... 37
Switching to active mode ................... 37
Switching to Eco Power standby mode
.................................................................. 37
Recording to an external device............ 38
Using the remote to operate your
television ..................................................... 38
Troubleshooting ....................... 39–40
Specifications ................................ 41
Glossary ......................................... 42
001-041-LX36-22-Eng 21/08/2003, 9:43 AM7
8
English
3139 115 22612
Supplied accessories
General Information
FM wire antenna
MW loop antenna
Scart cable (black)
Care and safety information
Avoid high temperatures, moisture,
water and dust
– Do not expose the system, batteries
or discs to humidity, rain, sand or
excessive heat (caused by heating
equipment or direct sunlight.) Always
keep the disc tray closed to avoid getting
dust on the lens.
Avoid condensation problem
– The lens may cloud over when the
player is suddenly moved from cold to
warm surroundings, making it impossible
to play a disc. Leave the player in the
warm environment until the moisture
evaporates.
Do not block the vents
– Do not operate the DVD system in an
enclosed cabinet and allow about 10 cm
(4 inches) of free space all around the
player for adequate ventilation.
10 cm
(4 inches)
10 cm
(4 inches)
10 cm
(4 inches)
DVD Home Cinema System
PHILIPS
Care of disc
– To clean a CD, wipe it in
a straight line from the
centre towards the edge
using a soft, lint-free cloth.
Do not use cleaning agent,
as they may damage the
disc!
– Write only on the printed side of a
CDR(W) and only with a soft felt-tipped
pen.
– Handle the disc by its edge, do not
touch the surface.
Care of the cabinet
– Use a soft cloth slightly moistened
with a mild detergent solution. Do not
use a solution containing alcohol, spirits,
ammonia or abrasives.
Finding a suitable location
– Place the player on a flat, hard, stable
surface.
Remote control
and two batteries
(4x)
(4x)
Subwoofer’s
rubber feet
Brackets and
screws
001-041-LX36-22-Eng 21/08/2003, 9:43 AM8
9
English
3139 115 22612
Connections
Step 2: Connecting speakers
and subwoofer
~AC
MAINS
FRONT
RIGHT
CENTER
FRONT
LEFT
REAR
RIGHT
REAR
LEFT
SUB-
W
SPEAKERS (4 )
AUX IN
LINE OUT
AUDIO
L
R
L
R
Front
Right
Front
Left
Rear Right Rear Left
Centre
Connect the supplied speaker systems
using the fixed speaker cables by
matching the colours of the jacks and
speaker cables.
~
A
C
M
AINS
FRONT
RIGHT
CE
NTER
FRONT
L
EFT
SURR.
RIGHT
SU
RR.
L
EFT
SU
B-
W
SPEAK
ERS (4 )
Helpful Hints:
– Ensure that the speaker cables are
correctly connected. Improper connections
may damage the system due to short-circuit.
– Do not connect speakers with an
impedance lower than the speakers supplied.
Please refer to the SPECIFICATIONS section
of this manual.
Subwoofer
You can choose to mount the speakers
on the wall. Attach the supplied bracket
firmly to the rear of speakers using the
supplied screws. Then mount a screw
(not supplied) on the wall where the
speaker is to be hung and hook the
speaker securely onto the mounted
screw.
CAUTION!
You should get a qualified person to
attach the brackets to the wall. DO
NOT do it by yourself to avoid
unexpected damage to the
equipment or injury to personnel.
Helpful Hints:
– The surround speakers are labelled as
REAR L (left) or REAR R (right).
– The front speakers are labelled as FRONT
L (left) or FRONT R (right).
Step 1: Set up the speakers
001-041-LX36-22-Eng 21/08/2003, 9:43 AM9
10
English
3139 115 22612
Connections
1
1
3
3
2
4
Step 3: Placing the speakers
and subwoofer
For best possible surround sound, all the
speakers (except subwoofer) should be
placed at the same distance from the
listening position.
1 Place the front left and right speakers at
equal distances from the TV and at an
angle of approximately 45 degrees from
the listening position.
2 Place the centre speaker above the TV or
the DVD system so that the centre
channel’s sound is localized.
3 Place the surround speakers at normal
listening ear level facing each other or
mounted on the wall.
4 Place the subwoofer on the floor near
the TV.
Front Speaker
(Left)
Front Speaker
(Right)
Centre speaker and
DVD System
Subwoofer
Rear speaker
(Right)
Rear speaker
(Left)
Helpful Hints:
– To avoid magnetic interference, do not
position the front speakers too close to your TV.
– Allow adequate ventilation around the
DVD system.
001-041-LX36-22-Eng 21/08/2003, 9:43 AM10
11
English
3139 115 22612
Step 4: Connecting TV
IMPORTANT!
– You only need to make one
video connection from the following
options, depending on the
capabilities of your TV system.
– Connect the DVD system
directly to the TV.
– Scart (RGB) Video connection
provides better picture quality than
S-Video. These options must be
available on your TV.
– If both S-Video and Scart video
connections are used to connect to
your TV, the TV signal will detect
automatically to SCART when you
power up the DVD system.
~AC
MAINS
FRONT
RIGHT
CENTER
FRONT
LEFT
REAR
RIGHT
REAR
LEFT
SUB-
W
SPEAKERS (4 )
AUX IN
LINE OUT
AUDIO
L
R
L
R
S-VIDEO
MW
FM/MW ANTEN
N
FM
SCART
AUDIO
OUT
S-VIDEO
IN
VIDEO IN
SCART IN
AUDIO
OUT
S-VIDEO
IN
VIDEO IN
SCART IN
OR
Connections
Using Scart jack
● Use the scart video cable (black) to
connect the DVD system’s SCART
OUT jack to the corresponding Scart
input jacks on the TV.
OR
Using S-Video jack
● Use the S-video cable (not supplied) to
connect the DVD system’s S-VIDEO
OUT jack to the S-Video input jack (or
labeled as Y/C or S-VHS) on the TV.
001-041-LX36-22-Eng 21/08/2003, 9:43 AM11
12
English
3139 115 22612
S-VIDEO
MW
FM/MW ANTENNA
FM 75
SCART
1
2
➠
FM
antenna
MW
antenna
fix the claw
into the
slot
Connections
After everything is connected
properly, plug in the AC power cord
to the power outlet.
Never make or change any connections
with the power switched on.
On the DVD system, press SOURCE
to select TUNER mode,
"AUTO INSTALL PRESS PLAY" may
appear on the display panel. Press
ÉÅ
on the front panel to store all available
radio stations or
press
Ç to exit (see page 34 “Tuner
Operations”).
TEM
IR
OPEN/CLOSE PLAY/PAUSE STOP
SOURCE
PREV NEXT
VOL UME
AUTO INSTALL PRESS PLAY
PLAY/PAUSE
Step 6: Connecting the
power cord
~AC
MAINS
FRONT
RIGHT
CENTE
~ AC MAINS
AUDIO
OUT
Pr/Cr
Pb/Cb
Y
S-VIDEO
IN
VIDEO IN
COMPONENT
VIDEO IN
1 Connect the supplied MW loop antenna
to the MW jack. Place the MW loop
antenna on a shelf or attach it to a stand
or wall.
2 Connect the supplied FM antenna to the
FM jack. Extend the FM antenna and fix
its ends to the wall.
For better FM stereo reception, connect
an external FM antenna (not supplied).
MW
FM ANTENNA
Helpful Hints:
– Adjust the position of the antennas for
optimal reception.
– Position the antennas as far as possible
from your TV, VCR or other radiation source
to prevent unwanted interference.
Step 5: Connecting FM/MW
antennas
001-041-LX36-22-Eng 21/08/2003, 9:44 AM12
13
English
3139 115 22612
Connections (Optional)
Connecting a VCR
~AC
MAINS
FRONT
RIGHT
CENTER
FRONT
LEFT
REAR
RIGHT
REAR
LEFT
SUB-
W
SPEAKERS (4 )
AUX IN
LINE OUT
AUDIO
L
R
L
R
S-VIDEO
MW
FM/MW ANTENNA
FM 75
SCART
AUDIO
OUT
S-VIDEO
IN
VIDEO IN
SCART IN
AUDIO
OUT
S-VIDEO
IN
VIDEO IN
2
4
3
1
ANT IN
TO TV
~ AC MAINS
SCART IN
S-VIDEO
VCR
Viewing and listening to the
playback
1 Connect the VCR to the TV as shown.
2 Connect the DVD system’s AUX IN
(R/L) jacks to the AUDIO OUT jacks on
the VCR.
Before starting operation, press AUX on
the remote to select “AUX” in order to
activate the input source.
Using the VCR for recording DVD
playback
Some DVDs are copy-protected. You
cannot record or dub protected discs
using a VCR.
3 Connect the DVD system’s S-VIDEO
jack to the S-VIDEO IN jack on the VCR.
4 Connect the DVD system’s LINE OUT
(R/L) jacks to the AUDIO IN jacks on
the VCR.
This will allow you to make analogue
stereo (two channel, right and left)
recordings.
To view DVD playback while
recording,
you must connect the DVD system to
your TV using the SCART (as shown
above) connection.
001-041-LX36-22-Eng 21/08/2003, 9:44 AM13
14
English
3139 115 22612
Functional Overview
* = Press and hold the button for more than two seconds.
Main unit and remote control
1 STANDBY ON (B)
– Switches to Eco Power standby mode or
turns on the system.
– Led ON in Eco Power standby mode.
2
Disc tray
3 System display panel
4 iR SENSOR
– Point the remote control towards this
sensor.
5 SOURCE
– Selects the relevant active source mode:
DISC, TV, TUNER or AUX.
– DISC: to switch to DISC source mode.
– TV: to switch to TV source mode and/or
*to turn on the Philips TV (remote
control only)
– TUNER: toggles between FM and MW
band.
– AUX: to switch to AUX source mode.
6
OPEN•CLOSE 0
– Opens/Closes the disc tray.
DVD HOME ENTERTAINMENT SYSTEM
IR
OPEN/CLOSE PLAY/PAUSE STOP
SOURCE
PREV NEXT
VOLUME
STANDBY-ON
1
2 3 4 56 7 8
7 ÉÅ PLAY•PAUSE
– DISC: starts/pauses playback.
– TUNER: starts preset radio station
installation in Plug & Play mode (only on
the main unit).
Ç STOP
– Exits an operation.
– DISC: stops playback.
– TUNER: *erases a preset radio station.
S PREV / NEXT T
– DISC: *searches backward/forward or
selects a track.
– TV: selects previous/next channel on the
Philips TV (remote control only)
– TUNER: tunes the radio frequency up/
down.
8
VOLUME (VOL +-)
– Adjusts the volume level.
001-041-LX36-22-Eng 21/08/2003, 9:44 AM14
15
English
3139 115 22612
Functional Overview
* = Press and hold the button for more than two seconds.
Control buttons available on the
remote only
9
DISC MENU
– Enters or exits disc contents menu.
– For VCD version 2.0 only;
In stop mode, turns on/off playback
control (PBC) mode.
During playback, returns to main menu.
0
OSD (DISC source mode only)
– Enters or exits on-screen display.
!
1 2 3 4
– Selects movement direction in the menu.
– Use 1 2 to select a preset radio station.
– Use 3 4 to select auto tuning in Tuner
source mode.
@
ANGLE
– Select a DVD disc camera angle (if
available)
# SUBTITLE
– Selects a subitle language.
$ REPEAT
– Selects various repeat modes.
%
REPEAT A-B
– Repeats a specific section on a disc.
^
AUDIO
– Selects an audio language (DVD) or an
audio channel (CD).
&
MUTE
– Mutes or restores the volume.
*
PROG (PROGRAM)
– DISC: starts programming.
– TUNER: starts *automatic/ manual preset
programming.
( SOUND
– Selects a sound effect.
)
SLEEP
– Sets the sleep timer function.
¡
SURROUND (SURR.)
– Selects multichannel surround or stereo
mode.
™ TV VOL +-
– Adjusts TV volume (Philips TV only).
£
SCAN
– Plays the first few seconds of each track/
chapter within a disc.
≤ RETURN/TITLE
– To go back to previous menu.
– Display the disc’s Title menu (if available)
∞ SET UP
– Enters or exits system setup menu.
§
ZOOM
– Enlarges a picture on the TV screen.
≥
OK
– Confirms a selection.
• Numeric Keypad (0-9)
– Enters a track/title number of the disc.
– Enters a number of a preset radio station.
ª
B
– Switches to Eco Power standby mode.
– *Switches Philips TV to on/off (in TV
mode).
5
ª
9
0
!
7
@
#
$
%
^
&
*
(
•
8
≥
!
§
∞
≤
¡
)
™
£
001-041-LX36-22-Eng 21/08/2003, 9:44 AM15
16
English
3139 115 22612
Step 1: Inserting batteries
into the remote
control
1
3
2
1 Open the battery compartment.
2 Insert two batteries type R06 or AA,
following the indications (+-) inside the
compartment.
3 Close the cover.
Using the remote control to operate
the system
1 Aim the remote control
directly at the remote
sensor (iR) on the front
panel.
2 Select the source you wish
to control by pressing one
of the source select
buttons on the remote
control (for example
TV, TUNER).
3 Then select the desired
function (for example
ÉÅ,
S,
T).
CAUTION!
– Remove batteries if they are
exhausted or if the remote is not to
be used for a long time.
– Do not use old and new or
different types of batteries in
combination.
– Batteries contain chemical
substances, so they should be
disposed of properly.
Getting Started
IR
OPEN/CLOSE PLAY/PAUS
E
SOURCE
PREV
Step 2: Setting the TV
IMPORTANT!
Make sure you have completed all
the necessary connections. (See
page 11 “Connecting TV”).
1 Press SOURCE control until “DISC”
appears on the display panel (or press
DISC on the remote).
2 Turn on the TV and set to the correct
video-in channel. You should see the blue
Philips DVD background screen on the
TV.
3 Usually this channel is between the
lowest and highest channels and may be
called FRONT, A/V IN, or VIDEO. See
your TV manual for more details.
➜Or, you may go to channel 1 on your
TV, then press the Channel down button
repeatedly until you see the Video In
channel.
➜Or, the TV remote control may have a
button or switch that chooses different
video modes.
➜Or, set the TV to channel 3 or 4 if you
are using an RF modulator.
001-041-LX36-22-Eng 21/08/2003, 9:44 AM16
17
English
3139 115 22612
Selecting the colour system that
corresponds to your TV
This DVD system is compatible with both
NTSC and PAL. In order for a DVD to
play on this DVD system, the colour
system of the DVD, the TV and the DVD
system should match.
1 Stop playback (if any) and press SETUP.
2 Press 2 twice to select ‘Video Setup
Page’.
3 Press 3 4 to highlight ‘TV Type’.
4 Enter its submenu by pressing 2.
5 Move the cursor by pressing 3 4 to
highlight one of the option below:
Multi – Select this if the connected TV is
compatible with both NTSC and PAL
(multi-system). The output format will be
in accordance with the video signal of the
disc.
NTSC – Select this if the connected TV
is NTSC system. It will change the video
signal of a PAL disc and output to NTSC
format.
PAL – Select this if the connected TV is
PAL system. It will change the video signal
of an NTSC disc and output to PAL
format.
6 Select an item and press OK.
To remove the menu
Press SETUP.
Getting Started
Step 3: Setting the speakers’
channels
You can adjust the delay times (centre
and surround only) and volume level for
individual speakers. These adjustments let
you optimise the sound according to your
surroundings and setup. Speaker settings
are only active on Multi-channel audio
outputs.
1 In DISC mode, press SETUP.
2 Press 2 to select ‘Audio Setup Page’.
3 Press 3 4 to highlight the ‘Speaker
Setup’.
4 Enter its submenu by pressing 2.
5 Press 3 4 to select (Front L&R, Center,
Surr L&R, Sub Woofer), then press
2 to
enter the speaker setting menu.
6 Use 3 4 to select the settings for each
speaker that suit your surround sound
needs, which may includes :
➜Delay time settings - use the longer
delay settings when the surround
speakers are closer to the listener than
the front speakers.
➜Adjusting the volume levels for one or
both speakers until the sound evens.
➜The test tone will be automatically
generated.
7 Press OK to confirm.
To remove the menu
Press SETUP.
- - VIDEO SETUP PAGE - -
TV TYPE PAL
TV DISPLAY NTSC
CLOSED CAPTION MULTI
PICTURE SETTING
- - AUDIO SETUP PAGE - -
SPEAKER SETUP
ANALOG OUTPUT
- - SPEAKER SETUP PAGE - -
FRONT SPEAKERS
CENTER SPEAKER
REAR SPEAKERS
SUBWOOFER
NIGHT MODE
001-041-LX36-22-Eng 21/08/2003, 9:44 AM17
18
English
3139 115 22612
Getting Started
Step 4: Setting language
preference
You can select your preferred language
settings so that this DVD system will
automatically switch to the language for
you whenever you load a disc. If the
language selected is not available on the
disc, the disc’s default setting language will
be used instead. Except the DVD
system’s OSD language, it will remain
once selected.
Setting the OSD Language
1 Stop playback (if any) and press SETUP.
2 Press 2 to select ‘General Setup Page’.
3 Press 3 4 to highlight the ‘OSD
Language’ in the General Setup Page.
4 Enter its submenu by pressing 2.
5 Select a language and press OK.
To remove the menu
Press SETUP.
Setting the Audio, Subtitle and Disc
menu language
1 Stop playback (if any) and press SETUP.
2 Press 2 to select ‘Preference Page’.
3 Press 3 4 to highlight the following in
the Preference Page.
–‘Audio’ (disc’s soundtrack)
–‘Subtitle’ (disc’s subtitles)
–‘Disc Menu’ (disc’s menu)
4 Enter its submenu by pressing 2.
5 Select a language and press OK.
6 Repeat steps 3~5 for other settings.
To remove the menu
Press SETUP.
If you choose OTHERS in Audio,
Subtitle or Disc Menu,
1 Press 3 4 to highlight ‘Others’.
2 Press OK and when you are asked to
enter a language code (see ‘Language
Code’).
3 Input a language code by using the
numeric keypad (0-9).
4 Press OK to confirm.
- - GENERAL SETUP PAGE - -
DISC LOCK
PROGRAM
OSD LANGUAGE ENGLISH
SCREEN SAVER CHINESE
FRENCH
SPANISH
PORTUGUESE
- - PREFERENCE PAGE - -
AUDIO ENGLISH
SUBTITLE CHINESE
DISC MENU FRENCH
PARENTAL SPANISH
DEFAULT PORTUGUESE
MP3/JPEG NAV POLISH
PBC ITALIAN
001-041-LX36-22-Eng 21/08/2003, 9:44 AM18
19
English
3139 115 22612
Getting Started
Language Code
Abkhazian 6566
Afar 6565
Afrikaans 6570
Albanian 8381
Amharic 6577
Arabic 6582
Armenian 7289
Assamese 6583
Avestan 6569
Aymara 6589
Azerhaijani 6590
Bashkir 6665
Basque 6985
Belarusian 6669
Bengali 6678
Bihari 6672
Bislama 6673
Bokmål, Norwegian 7866
Bosnian 6683
Breton 6682
Bulgarian 6671
Burmese 7789
Castilian, Spanish 6983
Catalan 6765
Chamorro 6772
Chechen 6769
Chewa; Chichewa; Nyanja 7889
Chinese 9072
Chuang; Zhuang 9065
Church Slavic; Slavonic 6785
Chuvash 6786
Cornish 7587
Corsican 6779
Croatian 6779
Czech 6783
Danish 6865
Dutch 7876
Dzongkha 6890
English 6978
Esperanto 6979
Estonian 6984
Faroese 7079
Fijian 7074
Finnish 7073
French 7082
Frisian 7089
Gaelic; Scottish Gaelic 7168
Gallegan 7176
Georgian 7565
German 6869
Gikuyu; Kikuyu 7573
Greek 6976
Guarani 7178
Gujarati 7185
Hausa 7265
Hebrew 7269
Herero 7290
Hindi 7273
Hiri Motu 7279
Hungarian 7285
Icelandic 7383
Ido 7379
Interlingua (International) 7365
Interlingue 7365
Inuktitut 7385
Inupiaq 7375
Irish 7165
Italian 7384
Japanese 7465
Javanese 7486
Kalaallisut 7576
Kannada 7578
Kashmiri 7583
Kazakh 7575
Khmer 7577
Kinyarwanda 8287
Kirghiz 7589
Komi 7586
Korean 7579
Kuanyama; Kwanyama 7574
Kurdish 7585
Lao 7679
Latin 7665
Latvian 7686
Letzeburgesch; 7666
Limburgan; Limburger 7673
Lingala 7678
Lithuanian 7684
Luxembourgish; 7666
Macedonian 7775
Malagasy 7771
Malay 7783
Malayalam 7776
Maltese 7784
Manx 7186
Maori 7773
Marathi 7782
Marshallese 7772
Moldavian 7779
Mongolian 7778
Nauru 7865
Navaho; Navajo 7886
Ndebele, North 7868
Ndebele, South 7882
Ndonga 7871
Nepali 7869
Northern Sami 8369
North Ndebele 7868
Norwegian 7879
Norwegian Nynorsk; 7878
Occitan; Provencal 7967
Old Bulgarian; Old Slavonic 6785
Oriya 7982
Oromo 7977
Ossetian; Ossetic 7983
Pali 8073
Panjabi 8065
Persian 7065
Polish 8076
Portuguese 8084
Pushto 8083
Quechua 8185
Raeto-Romance 8277
Romanian 8279
Rundi 8278
Russian 8285
Samoan 8377
Sango 8371
Sanskrit 8365
Sardinian 8367
Serbian 8382
Shona 8378
Sindhi 8368
Sinhalese 8373
Slovak 8373
Slovenian 8376
Somali 8379
Sotho; Southern 8384
South Ndebele 7882
Sundanese 8385
Swahili 8387
Swati 8383
Swedish 8386
Tagalog 8476
Tahitian 8489
Tajik 8471
Tamil 8465
Tatar 8484
Telugu 8469
Thai 8472
Tibetan 6679
Tigrinya 8473
Tonga (Tonga Islands) 8479
Tsonga 8483
Tswana 8478
Turkish 8482
Turkmen 8475
Twi 8487
Uighur 8571
Ukrainian 8575
Urdu 8582
Uzbek 8590
Vietnamese 8673
Volapuk 8679
Walloon 8765
Welsh 6789
Wolof 8779
Xhosa 8872
Yiddish 8973
Yoruba 8979
Zulu 9085
001-041-LX36-22-Eng 21/08/2003, 9:44 AM19
20
English
3139 115 22612
IMPORTANT!
– DVD discs and players are
designed with regional restrictions.
Before playing a disc, make sure the
disc is for the same zone as your
player.
– Depending on the DVD or
VIDEO CD, some operations may
be different or restricted.
– Do not push on the disc tray or
put any objects other than discs on
the disc tray. Doing so may cause
the disc player to malfunction.
Playable discs
Your DVD home cinema system will
play:
– Digital Video Discs (DVDs)
– Video CDs (VCDs)
– Super Video CDs (SVCDs)
– Digital Video Discs + Rewritable(DVD+RW)
– Compact Discs (CDs)
– MP3 discs, picture (Kodak, JPEG) files
on CD-R(W).
– JPEG/ISO 9660 format.
– Maximum 30 characters display.
– Supported sampling frequencies :
32 kHz, 44.1 kHz, 48 kHz
– Supported Bit-rates : 32~256 (kbps),
variable bit rates
Region Codes
DVDs must be labelled for ALL
regions or Region 2 in order to
play on this DVD system. You
cannot play discs that are labelled
for other regions.
Helpful Hint:
– If you are having trouble playing a certain
disc, remove the disc and try a different one.
Improperly formatted discs will not play on
this DVD system.
IMPORTANT!
If the inhibit icon (
ø or X) appears
on the TV screen when a button is
pressed, it means the function is not
available on the current disc or at
the current time.
Playing discs
1 Adjust SOURCE control until “DISC”
appears on the display panel (or press
DISC on the remote).
2 Turn on the TV power and set to the
correct Video In channel. (See page 16
“Setting the TV”).
➜You should see the blue Philips DVD
background screen on the TV.
3 Press OPEN•CLOSE 0 button once to
open the disc tray and load a disc, then
press the same button again to close the
disc tray.
➜Make sure the disc label is facing up.
For double-sided discs, load the side you
want to play face up.
4 Playback will start automatically.
➜If a disc menu shows on the TV, see
next page on “Using the Disc Menu”.
➜If the disc is locked by parental control,
you must enter your six-digit password.
(See page 32-33 “Parental”).
ALL
Disc Operations
2
001-041-LX36-22-Eng 21/08/2003, 9:44 AM20
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41

Philips LX3600D User manual

Philips
Brand
Philips
Model
LX3600D
Category
Home cinema systems
Type
User manual
This manual is also suitable for
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents