Graco 313788A Owner's manual

Graco
Brand
Graco
Model
313788A
Category
Paint Sprayer
Type
Owner's manual

This manual is also suitable for

Graco 313788A is a replacement control board kit for Ultra Max II, Ultimate Mx II, and TexSpray Mark IV, Mark V sprayers. It is designed to replace the original control board in these sprayers, and it is programmed at the factory so that no clipping of resistors is necessary. The kit includes a new control board, thermal paste, and instructions for installation.

The Graco 313788A control board is an important part of your sprayer. It controls the sprayer's motor, pump, and other functions. If your sprayer is not working properly, replacing the control board may be necessary. The kit includes everything you need to install the new control board yourself, and the instructions are easy to follow.

Graco 313788A is a replacement control board kit for Ultra Max II, Ultimate Mx II, and TexSpray Mark IV, Mark V sprayers. It is designed to replace the original control board in these sprayers, and it is programmed at the factory so that no clipping of resistors is necessary. The kit includes a new control board, thermal paste, and instructions for installation.

The Graco 313788A control board is an important part of your sprayer. It controls the sprayer's motor, pump, and other functions. If your sprayer is not working properly, replacing the control board may be necessary. The kit includes everything you need to install the new control board yourself, and the instructions are easy to follow.

313788A
Instructions
Replacement Control Board Kit for:
Ultra Max II 695/795/1095/1595
™
Ultimate Mx II 695/795/1095/1595
™
TexSpray
™
Mark IV, Mark V
- This manual contains kit installation instructions only -
Pressure Relief Procedure
1. Turn pressure to zero.
2. Turn on/off switch to OFF.
3. Unplug power supply cord.
4. Hold metal part of gun firmly to grounded metal pail.
Trigger gun to relieve pressure.
5. Lock gun safety latch.
6. Open pressure drain valve. Leave pressure drain
valve open until ready to spray again.
If you suspect that the spray tip or hose is completely
clogged or that pressure has not been fully relieved after
following the steps above, VERY SLOWLY loosen the tip
guard retaining nut or hose end coupling to relieve pres-
sure gradually. Then loosen it completely. Clear the tip or
hose obstruction.
Installation
NOTE: Replacement Control Board is programmed at
factory. No clipping of resistors is necessary.
1. Perform Pressure Relief Procedure.
2. Remove shroud, disconnect wire connectors
,
r
emove control box, and remove control board (refer
to sprayer Repair manual for detailed instructions).
3. Clean old thermal paste off of back of control board
and the mating areas on the sprayer.
4. Apply a thin layer of thermal paste to the two compo-
nents on the back of the control board.
5. Install control board, control box, connect wires, an
d
ins
tall shroud (refer to sprayer Repair manual for
detailed instructions).
IMPORTANT SAFETY INSTRUCTIONS
For detailed sprayer information and warnings,
see Repair manual included with the sprayer.
SKIN INJECTION HAZARD
System pressure must be manually relieved to prevent
system from starting or spraying accidentally. Fluid
under high pressure can be injected through skin and
cause serious injury. To reduce risk of injury from
injection, splashing fluid, or moving parts, follow
Pressure Relief Procedure whenever you:
• are instructed to relieve pressure
• stop spraying
• check or service any system equipment
• install or clean spray tip
NOTICE
Electrostatic discharges can damage components
on Control board. Use a ground strap when handling
or installing Control board.
2 313788A
All written and visual data contained in this document reflects the latest product information available at the time of publication.
Graco reserves the right to make changes at any time without notice.
This manual contains English. MM 313788
Graco Headquarters: Minneapolis
International Offices: Belgium, China, Japan, Korea
GRACO INC. P.O. BOX 1441 MINNEAPOLIS, MN 55440-1441
Copyright 2009, Graco Inc. is registered to ISO 9001
www.graco.com
  • Page 1 1
  • Page 2 2

Graco 313788A Owner's manual

Graco
Brand
Graco
Model
313788A
Category
Paint Sprayer
Type
Owner's manual
This manual is also suitable for

Graco 313788A is a replacement control board kit for Ultra Max II, Ultimate Mx II, and TexSpray Mark IV, Mark V sprayers. It is designed to replace the original control board in these sprayers, and it is programmed at the factory so that no clipping of resistors is necessary. The kit includes a new control board, thermal paste, and instructions for installation.

The Graco 313788A control board is an important part of your sprayer. It controls the sprayer's motor, pump, and other functions. If your sprayer is not working properly, replacing the control board may be necessary. The kit includes everything you need to install the new control board yourself, and the instructions are easy to follow.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents