Smeg DWF614WH is an efficient dishwasher that will meet the expectations even of the most demanding users. It is equipped with a water softening system, rinse aid and detergent dispensers, and an array of washing programs, so you can be sure that your dishes will always come out sparkling clean. The dishwasher also features a user-friendly front panel and information display, making it easy to operate. Additionally, the dishwasher has a spacious interior with adjustable baskets, allowing you to fit even large pots and pans inside.
Smeg DWF614WH is an efficient dishwasher that will meet the expectations even of the most demanding users. It is equipped with a water softening system, rinse aid and detergent dispensers, and an array of washing programs, so you can be sure that your dishes will always come out sparkling clean. The dishwasher also features a user-friendly front panel and information display, making it easy to operate. Additionally, the dishwasher has a spacious interior with adjustable baskets, allowing you to fit even large pots and pans inside.
INSTRUCTION MANUAL
DISHWASHER
Contents
25
1. Safety and operating instructions __________________________ 26
2. Installation and hook-up _________________________________ 28
2.1 Water supply connection _____________________________________________________ 28
2.2 Electrical connection ________________________________________________________ 29
3. Description of the controls _______________________________ 30
3.1 Front panel ________________________________________________________________ 30
3.2 Information display__________________________________________________________ 30
3.3 Washing programs__________________________________________________________ 32
4. Operating instructions___________________________________ 35
4.1 Using the water softening system ______________________________________________ 35
4.2 Using the rinse aid and detergent dispensers _____________________________________ 36
4.3 General warnings and recommendations ________________________________________ 38
4.4 Using the baskets___________________________________________________________ 39
5. Cleaning and maintenance _______________________________ 42
5.1 General warnings and recommendations ________________________________________ 42
6. Troubleshooting _______________________________________ 45
Thank you for choosing this product.
We advise you to carefully read all the instructions contained in this manual, in order to understand
how to operate your dishwasher safely and correctly.
The manual is divided into paragraphs, which provide a step by step description of the dishwasher
functions, with clear instructions accompanied by detailed illustrations.
Recommendations are given for the correct use of the baskets, spray arms, containers, filters,
washing programs, and for operating the controls.
Follow the recommended cleaning procedures to ensure that your dishwasher always remains in
perfect working order.
This manual provides a quick and easy reference for answering all your questions concerning the
use of your new dishwasher.
INSTALLATION INSTRUCTIONS: these are intended for the
qualified technician
who must carry
out the installation, hook-up and testing of the appliance.
USER INSTRUCTIONS: these consist of recommendations for using the appliance, a description of
its controls and of the correct cleaning and maintenance procedures.
Safety instructions
26
1. Safety and operating instructions
THIS MANUAL FORMS AN INTEGRAL PART OF THE APPLIANCE: IT MUST ALWAYS BE KEPT INTACT TOGETHER
WITH THE DISHWASHER. BEFORE USING THE APPLIANCE, CAREFULLY READ ALL THE INSTRUCTIONS
CONTAINED IN THIS MANUAL. INSTALLATION MUST BE PERFORMED BY A QUALIFIED TECHNICIAN, IN
COMPLIANCE WITH THE REGULATIONS IN FORCE. THIS APPLIANCE IS INTENDED FOR DOMESTIC USE, AND
COMPLIES WITH THE
EEC DIRECTIVES 72/23, 89/336 (INCLUDING 92/31)
CURRENTLY IN FORCE, INCLUDING THE
PREVENTION AND ELIMINATION OF RADIO FREQUENCY INTERFERENCE. THE APPLIANCE IS DESIGNED FOR
THE FOLLOWING PURPOSE:
WASHING AND DRYING OF DISHES
; ANY OTHER USE SHALL BE CONSIDERED
IMPROPER.
THE MANUFACTURER DECLINES ALL RESPONSIBILITY FOR USES OTHER THAN THOSE
DESCRIBED ABOVE.
THE NAME PLATE FEATURING THE TECHNICAL DATA, SERIAL NUMBER AND MARKINGS IS VISIBLY POSITIONED
ON THE INNER EDGE OF THE DOOR.
THE NAME PLATE ON THE INNER EDGE OF THE DOOR MUST NEVER BE
REMOVED.
DO NOT LEAVE THE DISCARDED PACKAGING MATERIALS UNSUPERVISED WITHIN THE HOME. SEPARATE THE
VARIOUS MATERIALS WHICH MAKE UP THE PACKAGING AND TAKE THEM TO THE NEAREST SORTED WASTE
COLLECTION CENTRE.
THE APPLIANCE MUST BE PROVIDED WITH AN EARTH CONNECTION IN ACCORDANCE WITH THE ELECTRICAL
SAFETY REGULATIONS IN FORCE.
THE MANUFACTURER DECLINES ALL RESPONSIBILITY FOR DAMAGE TO PERSONS OR PROPERTY RESULTING
FROM THE FAILURE TO EARTH THE APPLIANCE OR FROM A DEFECTIVE EARTH CONNECTION.
IF THE APPLIANCE IS NOT CONNECTED TO THE ELECTRICAL POWER SUPPLY BY MEANS OF A PLUG, IT IS
NECESSARY TO INSTALL AN ISOLATION SWITCH WITH A CONTACT OPENING GAP OF AT LEAST 3 MM.
THE PLUG ON THE POWER CORD AND THE CORRESPONDING SOCKET OUTLET MUST BE OF THE SAME TYPE,
AND MUST CONFORM TO THE REGULATIONS IN FORCE. CHECK THAT THE VOLTAGE AND FREQUENCY OF THE
ELECTRICAL POWER SUPPLY MATCH THE RATINGS ON THE NAME PLATE. AVOID USING ADAPTORS OR SHUNT
CONNECTIONS.
NEVER UNPLUG THE APPLIANCE BY PULLING THE POWER CORD.
• AFTER INSTALLATION, THE PLUG MUST REMAIN ACCESSIBLE.
• IN THE EVENT OF DAMAGE TO THE POWER CORD, HAVE IT REPLACED BY A QUALIFIED TECHNICIAN.
IF THE APPLIANCE IS INSTALLED ON A CARPETED OR COVERED FLOOR, ENSURE THAT THE OPENINGS ON ITS
UNDERSIDE ARE NOT OBSTRUCTED.
ALWAYS SWITCH OFF THE DISHWASHER AFTER EACH USE TO AVOID WASTING ELECTRICITY.
OBSOLETE APPLIANCES MUST BE RENDERED UNUSABLE. CUT OFF THE MAINS POWER CORD AFTER
UNPLUGGING IT FROM THE WALL OUTLET, AND MAKE SAFE ANY COMPONENTS WHICH MIGHT BE DANGEROUS
FOR CHILDREN (LOCKS, DOORS, ETC.). THE APPLIANCE MUST THEN BE TAKEN TO A SORTED WASTE
COLLECTION CENTRE.
IN THE EVENT OF A FAULT, DISCONNECT THE DISHWASHER FROM THE ELECTRICAL POWER SUPPLY AND
SHUT OFF THE WATER TAP. THEN CALL IN A QUALIFIED TECHNICIAN.
Safety instructions
27
DO NOT USE APPLIANCES WHICH HAVE BEEN DAMAGED DURING TRANSIT! IF IN DOUBT, CONSULT YOUR
DEALER.
THE APPLIANCE MUST BE INSTALLED AND CONNECTED IN ACCORDANCE WITH THE INSTRUCTIONS PROVIDED
BY THE MANUFACTURER OR BY A QUALIFIED TECHNICIAN.
THE APPLIANCE IS INTENDED FOR USE BY ADULTS.
DO NOT ALLOW CHILDREN TO COME NEAR OR PLAY WITH
THE DISHWASHER. KEEP CHILDREN AWAY FROM DETERGENTS AND FROM THE OPEN DISHWASHER DOOR.
THE PACKAGING MATERIALS (PLASTIC BAGS, POLYSTYRENE, METAL BARS, ETC.) MUST NOT BE LEFT WITHIN
THE REACH OF CHILDREN.
KEEP CHILDREN AWAY FROM THE OPEN DISHWASHER. THE APPLIANCE MAY CONTAIN RESIDUES OF
DETERGENT WHICH CAN CAUSE IRREVERSIBLE DAMAGE TO THE EYES, MOUTH, AND THROAT, AS WELL AS
POSSIBLE DEATH BY SUFFOCATION.
DO NOT INTRODUCE SOLVENTS SUCH AS ALCOHOL OR TURPENTINE WHICH MAY CAUSE AN EXPLOSION.
DO NOT LOAD DISHES THAT ARE SOILED WITH ASH, WAX OR PAINTS.
LEANING OR SITTING ON THE DISHWASHER DOOR WHEN OPEN MAY CAUSE THE APPLIANCE TO OVERTURN,
PUTING PEOPLE AT RISK.
DO NOT UNDER ANY CIRCUMSTANCES TOUCH THE HEATING ELEMENT IMMEDIATELY AFTER THE END OF A
WASHING PROGRAM.
OVER TIME, THE DISHWASHER HEATING ELEMENTS MAY CHANGE COLOUR, IN PART OR OVERALL. THIS IS
PERFECTLY NORMAL AND DOES NOT IN ANY WAY AFFECT THE OPERATION OF THE APPLIANCE.
DO NOT DRINK THE WATER RESIDUES WHICH MAY BE PRESENT INSIDE THE DISHES OR DISHWASHER AT THE
END OF THE WASHING PROGRAM AND BEFORE THE DRYING CYCLE.
KNIVES OR OTHER SHARP-ENDED COOKING UTENSILS MUST BE PLACED IN THE CUTLERY BASKET BLADE-
DOWN, OR LAID HORIZONTAL IN THE TOP BASKET. TAKE CARE NOT TO CUT YOURSELF AND ENSURE THAT
THEY DO NOT PROJECT FROM THE BASKET.
AQUASTOP MODELS
THE AQUASTOP DEVICE PREVENTS FLOODING IN THE EVENT OF A WATER LEAK. WHEN THE AQUASTOP
DEVICE IS TRIPPED, CALL IN A QUALIFIED TECHNICIAN TO IDENTIFY AND REPAIR THE FAULT.
IN MODELS EQUIPPED WITH THE AQUSTOP DEVICE, THERE IS A SOLENOID VALVE INSIDE THE WATER INTAKE
HOSE.
DO NOT CUT THE HOSE AND DO NOT ALLOW THE SOLENOID VALVE TO DROP INTO WATER.
IN THE
EVENT OF DAMAGE TO THE WATER INTAKE HOSE, DISCONNECT THE APPLIANCE FROM THE ELECTRICAL
POWER SUPPLY AND FROM THE WATER SUPPLY.
IMMEDIATELY AFTER INSTALLING THE DISHWASHER, PERFORM A QUICK TEST OF THE APPLIANCE FOLLOWING
THE INSTRUCTIONS BELOW. IF THE DISHWASHER FAILS TO OPERATE CORRECTLY, DISCONNECT IT FROM THE
ELECTRICAL POWER SUPPLY AND CALL THE NEAREST TECHNICAL SERVICE CENTRE.
DO NOT ATTEMPT TO REPAIR THE APPLIANCE.
THE DISHWASHER MEETS ALL THE REQUIREMENTS SET OUT BY THE REGULATIONS IN FORCE CONCERNING
SAFETY AND ELECTRICAL EQUIPMENT. ANY TECHNICAL CHECKS SHOULD BE CONDUCTED EXCLUSIVELY BY A
TRAINED AND AUTHORISED TECHNICIAN:
REPAIRS CARRIED OUT BY UNAUTHORISED PERSONS WILL
INVALIDATE THE WARRANTY, AS WELL AS POSING A POTENTIAL HAZARD TO THE USER.
The manufacturer declines all responsibility
for damage to persons or property resulting from failure to
observe the above precautions, from tampering with even a single component of the appliance, or from the use
of non original spare parts.
Installation instructions
28
2. Installation and hook-up
Remove the polystyrene basket retainers.
Position the appliance in the desired place of installation. The back or sides of the dishwasher may
be placed up against walls or other furniture units.
If the dishwasher is installed near a heat source, fit the special insulating panel to prevent
overheating and malfunction of the appliance.
To ensure stability, install integrated or built-under dishwashers only under continuous worktops,
and screw them to the adjacent units.
To facilitate the installation procedure, the intake and drain hoses can be positioned in any
direction; make sure that the hoses are not kinked, crushed or pulled too tightly. A hole at least 8
cm in diameter is required to allow the power supply cable and pipes to pass.
Level the appliance on the floor using its adjustable feet. This operation is essential for ensuring
correct operation of the dishwasher.
Some models are equipped with only one adjustable foot at the rear, which can be adjusted by
turning the screw on the lower front part of the appliance.
2.1 Water supply connection
Preventing the risk of clogging or damage:
if the water pipe is new or has not been used for a
long time, before connecting to the water supply check that the water is clear and free of impurities,
to prevent damage to the appliance.
The dishwasher must always be connected to the water system with new hoses; old or used
hoses must never be reused.
CONNECTING TO THE WATER SUPPLY
Connect the intake hose to a cold water supply with ¾” gas thread, inserting the filter
A
supplied
with the dishwasher.
Take care to screw the hose firmly into place with your hands and then complete by
tightening about ½ of a turn with pliers. In dishwashers equipped with the ACQUASTOP
device, the filters is already fitted inside the threaded ring.
The dishwasher can also be connected to a hot water supply
not exceeding 60°C
. Supplying the
appliance with hot water cuts down the washing time by approximately 20 minutes, but slightly
reduces its effectiveness. Make the connection to the domestic hot water supply using the same
procedure described for connecting to the cold water supply.
Installation instructions
29
DRAIN CONNECTION
Insert the dishwasher’s drain hose into a drain pipe
having a diameter of at least
4 cm
, or alternatively,
place it inside the kitchen sink using the plastic support
provided, taking care not to crush or excessively bend
the hose. It is important to prevent the hose from
coming loose and falling. For this purpose, the plastic
support is equipped with a hole for tying it to the wall or
water tap.
The free end should be positioned at a height of
between
30 and 100 cm
, and s ho uld ne ver be
submerged in water.
If a horizontal drain e xtension hose is used (for a
maximum of 3 m) the drain hose can be placed at a
maximum height of
85 cm
from the ground.
2.2 Electrical connection
Plug the power cord into a suitable electrical outlet, according to the instructions given in chapter
"1. Safety and operating instructions".
User instructions
30
3. Description of the controls
3.1 Front panel
All the dishwasher controls are grouped on the front panel.
1 ON/OFF
BUTTON
2 SELECTION PROGRAM
BUTTONS
(P1…P5)
3 ½ LOAD WASH
BUTTON (certain models only)
4 ECO DRYING CYCLE
BUTTON (certain models only)
5 DELAY PROGRAM
BUTTON (certain models only)
6 START/STOP
BUTTON
7 POWER ON
LIGHT
8 PROGRAMS
INDICATOR LIGHTS
9 INFORMATION DISPLAY
10
RECESSED DOOR HANDLE
3.2 Information display
The dishwasher is equipped with a practical
DISPLAY
which
provides information on the programmed dishwasher functions.
LIGHTING
Pressing the
ON/OFF
button
(1)
will start the dishwasher and will lit up the dishwasher pilot light
(7)
. After approximately
3 second
from this operation the
DISPLAY (9)
will be turned on with a
visualization that will depend upon the state of the dishwasher.
PROGRAMMING
In this dishwasher model all the programming operations are possible only with closed door. With
open door, on the
DISPLAY (9)
will appear the symbols
--
and the
PILOT LIGHT PROGRAMS (8)
remains out.
SELECTION PROGRAM
The program selection is possible through the
relative buttons
(2)
.
By pressing the relative button of desired program (see table) it will lid up the relative pilot light to
confirm that the operation did occurred on the
DISPLAY (9)
will appear a program duration
forecasting (“
h.mm
”).
TABLE OF PROGRAMS
AMOUNT OF
DET ERGENT
PROGRESS P ROGRAM
PROGRAM SELECTION
EC O
DRYING
(OPTIONAL)
TYP E A N D G RA DE DI RT
GRAM S PREWASH WASH COLD RINSE HOT RINSE DRY
SOAK
_
PANS AND DISHES IN WAITING
OF COMPLETING THE LOAD
_
COLD
_ _ _ _
QUICK
_
DISHES NOT MUCH DIRTY
AND WITH "FRESH DIRT"
WITHOUT RESIDUAL DRY
25
_
38°C 1 58°C
_
ECO
PANS AND DISHES
NOT VERY DIRTY
BUT WITH DRY RESIDUALS
30
_
55°C 1 68°C YES
DAILY
PANS AND DISHES
WITH NOR MAL DIRT,
WITHOUT DRY RESIDUAL
30
_
65°C
1
68°C
YES
STRONG
PANS AND DISHES
VERY DIRTY
30
_
70°C 2 68°C YES
DELICATE
+
DISHES NOT VERY DIRTY
25
COLD
45°C 1 68°C YES
BIO
(*)
+
PANS AND DISHES DIRTY
AND WITH DRY RESIDUALS
30
COLD
55°C 1 68°C YES
NORMAL
+
PANS AND DISHES DIRTY
AND WITH DRY RESIDUALS
30
COLD
65°C
1
68°C
YES
SUPER
+
PANS AND DISHES
VERY DIRTY
AND WITH DRY RESIDUALS
30 45°C 70°C 2 68°C YES
Only
run the soak program with half loads.
The
HALF LOAD
option
(3)
is available for all programs
except the soak program
.
(-) Not present.
In programs containing the
symbol, the
ECO drying cycle option
is available. This activates the ventilation system which allows the
dishes to be dried at lower temperatures (energy saving). With this option active, the program times are longer (about
50’
for the
BIO
program and about
20’
for all the other cycles).
TABLE FOR CERTIFICATION BODIES
Reference standard EN 50242
Reference program
(*)
BIO
+ program
Load 14 place-settings
Type of detergent B
Amount of detergent 35 g
Rinse aid setting Depending on the model
3/4 or 4/6
EN 50242 STANDARD LOADS
LOWER BASKET UPPER B ASKET
If the dishwasher door is left open or is
not properly closed, the INFORMATION
DISPLAY (9) will signal that the washing
program cannot be started.
For any other information about use and
maintenance of the dishwasher, read the
enclosed manual carefully.
19 510 0219 06
User instructions
31
START PROGRAM
At this point, in order to start the machine, it is only enough to press the
START/PAUSE (6)
for
some seconds until the writtin “
Time to end
” start to flash and confirmation “beep” is heard. From
this moment the cycle dration on the
DISPLAY (9)
starts to decrease.
This phase, that updates itself during the cycle, is “indicative” since it is influenced by the washing
conditions such as dishwasher type and quantity, entry temperature etc. For this reason it is normal
to see the updating during a program (increment and decrease of minutes) specially in the passage
from one phase to the other (for example, from washing to rinse).
END PROGRAM
The end of the program is indicated by a short signal acoustic and from the “
End
” visual notification
on
DISPLAY (9)
. By pressing one of the buttons, the “
End
” visual signal will vanish from the
display and the dishwasher is ready to continue a new cycle, the same thing happens when closing
or opening the door or by switching on-off the machine.
INTERRUPTING A PROGRAM
In order to interrupt a running program it is necessary:
•
to press the
START/STOP (6)
for some seconds until when the writting “
Time to end
” remains
lit on the display (confirmation beep). At this point,it is possible to start the cycle again,
otherwise:
TO CHANGE A PROGRAM
To change the running program it is necessary:
•
to interrupt the running program (see “
I
NTERRUPTING A PROGRAM
”);
•
select the new program;
•
to press again the
START/STOP
button
(6)
to make start the new program.
STOPPING A PROGRAM
To stop a program in progress, it must first be interrupted (see "
I
NTERRUPTING A PROGRAM
").
Now press buttons
P1
+
P2
simultaneously and the first three program
lights will come on.
The display will show "
P0
" and the dishwasher will immediately switch to the end of the cycle and
drain the tank (during this process, the "
Time to end
" message will flash).
When the drain procedure ends, the end of cycle message "
End
" appears on the display.
In case that the door is opened during the operation, to the next door closing it is going to be
necessary to start the program as shown in paragraph “
S
TART PROGRAM
”. The program will resume
from the point in which it was interrupted.
In case that the tub temperature is higher than 50°C the program will start 30 seconds later
the door closing (this, in order to avoid overpressure phenomenom inside the tub).
User instructions
32
3.3 Washing programs
The dishwasher is equipped with a control panel and an
INFORMATION DISPLAY (9)
from which
it is possible to carry out all the power switch-on, switch-off and programming operations.
Before starting a washing program make sure that:
•
The water supply tap is
open.
•
The
correct amount of detergent
has been added to the
dispenser
.
•
The baskets have been
correctly loaded.
•
The spray arms are able to
rotate freely
and without obstruction.
•
The dishwasher door is
securely closed
.
HALF LOAD WASH FUNCTION
This function is recommended for loads of up to
7 place-settings
, and cuts down on the use of
water and electricity.
By pressing the
½ LOAD WASH (3)
button it is possible to select only one basket washing (upper
or lower).
After having the program selected, continue as follows:
•
by pressing for one time the
½ LOAD WASH (3)
button, it will
select the upper basket and on the display will compare the
following visualization;
•
by pressing the
½ LOAD WASH (3)
button again the lower
basket is selected;
•
by pressing a third time the
½ LOAD WASH (3)
button it will bring back to the full load washing
mode.
N.B.:
by selecting the
½ LOAD
mode, a modification in the indication of the program duration will
set.
One half of the cutlery basket can be placed in the
½ LOAD
program basket.
WARNING: do not load dishes and cutlery into the non-selected basket, because the water
spray will only reach the selected basket.
DELAYING THE PROGRAM
The
PROGRAM DELAY
button
(5)
can be pressed to delay the start of the program by up to
12 hours
.
This means that the dishwasher can be operated at the time of day of your choice.
The first time the
PROGRAM DELAY
button
(5)
is pressed the display will show
12 hours
, the
maximum delay time before the program will start. Each subsequent time the button is pressed the
delay time will be reduced, until the desired delay time is reached.
Particularly, on the display it will have the following indications.
User instructions
33
Chosen the delay, proceed with the program start, press the button
START/PAUSE (6)
for same
seconds until the clock symbol start to flaash.
The machine will perform a dish pre-washing, and when finish, the “delay program” will enter in
function as it was first set.
In case you want to put to zero the “delay program” within the running program it is necessary:
•
to press the
START/STOP (6)
button for some seconds until the clock symbol remain lid up on
the display;
•
to press the
DELAY PROGRAM (5)
more times until the reset of the delay program (clock
symbol shut off);
•
to press the
START/STOP (6)
button to make start the program.
N.B.:
It is not possible to select the “
delay program
” when the program have already began.
TO SAVE ON ENERGY! … AND PROTECT THE ENVIRONMENT
•
Always try to run the dishwasher
fully loaded
.
•
Do not wash the dishes in running water.
•
Use the washing program that is
most appropriate
for each type of load.
•
Do not carry out any preliminary rinsing.
•
If available, connect the dishwasher to a hot water supply up to 60°C.
•
When possible,
skip the drying cycle
by leaving the door open when the washing cycle is
complete; the air and the residual heat will dry the dishes perfectly.
TO CUT DOWN ON DETERGENT CONSUMPTION! … AND PROTECT THE ENVIRONMENT
The phosphates contained in dishwasher detergents are harmful to the environment. To avoid
using excessive amounts of detergent and to save on electricity, observe the following:
• sep arate
the more delicate items from dishes that are more resistant to aggressive detergents
and high temperatures;
• do not pour
the detergent directly on the dishes.
REMOVING THE DISHES
At the end of the washing program, wait at least
20 minutes
before removing the dishes, to allow
them to cool down. To prevent any water droplets on the upper basket from falling on the dishes in
the lower basket, it is
advisable
to unload the lower basket first, and then the upper basket.
User instructions
34
ADDITIONAL FUNCTIONS (Customizing the consumer parameters)
The electronic control system allows personalizing the machine use directly through a
programming procedure not directly accessible that allows: regulate water hardness level.
To access the programming environment, the
appliance
must
be turned
on with the
door open
.
Then proceed as follows:
•
press the
ECO DRY (4)
button until the
H
symbol appears on the display, followed by the
number 3, >
H3
;
•
press the
PROGRAM DELAY (5)
button the number of times needed to select the right setting
level for the hardness of the water (
H0, H1, H2, H3, H4, H5
);
•
press the
START/STOP (6)
button to confirm the setting and return to the program setting
menu.
N.B.:
after 2 minutes, the appliance exits the parameter setting menu automatically.
WATER HARDNESS TABLE
WATER HARDNESS
German Degrees (°dH) French Degrees (°dF)
SETTING
0 - 4 0 - 7 .h 0
5 - 15 8 - 25 .h 1
16 - 23 26 - 40 .h 2
24 - 31 41 - 60 .h 3
32 - 47 61 - 80 .h 4
48 - 58 81 - 100 .h 5
Contact your local water board for information on the hardness of your water supply.
User instructions
35
4. Operating instructions
Once the dishwasher has been correctly installed, prepare for use as follows:
•
Adjust the water softening system;
•
Add the regenerating salt;
•
Add the rinse aid and detergent.
4.1 Using the water softening system
The amount of scale contained in the water (water hardness
index) can cause whitish staining on the dry dishes, which
tend to become dull over time. The dishwasher is equipped
with an automatic softening system which uses a special
regenerating salt to reduce the hardness of the water.
The dishwasher is factory set for water hardness level
3
(average hardness
41-60°dF
–
24-31°dH
).
When using water of medium hardness, the regenerating salt container should be refilled after
approximately
20 washing cycles
. The salt container can hold approximately
1.7 Kg
of salt in
grains. Some models are equipped with an optical no-salt indicator. In these models, the cap of the
salt container contains a green float which descends as the salt concentration in the water drops.
When the green float can no longer be seen through the transparent cap, the container must be
topped up with regenerating salt. The container is situated at the bottom of the dishwasher. After
removing the lower basket, unscrew the salt container cap by turning it anticlockwise and pour in
the salt using the funnel supplied with the dishwasher. Before replacing the cap, remove any salt
residues from around the opening.
•
When using the dishwasher for the first time, in addition to the salt it is also necessary to add
one litre of water
to the container.
•
Each time the salt container is refilled, make sure that
the cap is securely closed
. The
mixture of water and detergent must never penetrate the salt container, as this would
compromise the operation of the regeneration system. In the event of this occurring, the
warranty will be invalidated.
• Only
use regenerating salt specially formulated for domestic dishwashers. If using salt tablets,
do not fill the container completely
.
• Do not use table salt
as it contains insoluble substances which, over time, may damage the
water softening system.
•
When necessary, refill the regenerating salt container
before starting the washing program
.
In this way, the excess saline solution will be immediately removed by the water; the prolonged
presence of salt water inside the tank may lead to
corrosion
.
Be careful not to confuse the salt and detergent packages
; adding detergent to the salt
container will
damage
the water softening system.
SALT
User instructions
36
4.2 Using the rinse aid and detergent dispensers
The detergent and rinse aid dispensers are situated on the
inner part of the door: the
detergent dispenser
is on the left,
and the
rinse aid dispenser
is on the right.
With the exception of the
SOAK
program, before every washing cycle it is necessary to add the
required amount of detergent to the
detergent dispenser
. The rinse aid, on the other hand, should
only be added as required.
ADDING THE RINSE AID
The rinse aid helps the dishes dry faster and prevents the formation of scale deposits and staining;
it is automatically added to the water during the final rinse cycle, from the container situated on the
inner side of the door.
•
Open the door.
•
Rotate the container cap anticlockwise by ¼ of a turn and remove it.
•
Add the rinse aid until the container is full (approximately 140 cc). The optical level indicator on
the side of the cap should be completely obscured. Refill the rinse aid when the optical level
indicator becomes clear again, or when the rinse aid warning light illuminates.
•
Replace the cover and turn it in a clockwise direction.
•
Use a cloth to remove any spillage of rinse aid which might lead to the formation of excess
foam.
ADJUSTING THE RINSE AID DISPENSER SETTING
The dishwasher is factory set for medium water hardness. However it possible to change the
setting by turning the dispenser’s selector to the desired position: the amount of rinse aid
dispensed is proportional to the selector position.
The setting must be increased when the washed dishes appear dull or have circular staining.
•
To adjust the rinse aid setting, rotate the dispenser cap through a quarter turn in an
anticlockwise direction and remove it.
•
Then use a screwdriver to rotate the rinse aid selector to the desired position.
•
Replace the cap, turning it clockwise.
•
The amount of rinse aid must be
increased
if the washed dishes appear dull or feature circular
stains.
•
If, on the other hand, the dishes are sticky or have white streaks, it is necessary to
reduce
the
rinse aid setting.
User instructions
37
ADDING THE DETERGENT
To open the detergent dispenser cap, lightly press the button
P
. Add the detergent and close the
cap carefully.
During the washing cycle, the dispenser will be opened automatically.
•
When a
SUPER
program is selected, in addition to the normal dose of detergent, it is
necessary to add an additional amount inside compartment
G
or
H
.
•
Use
only
detergents specially formulated for dishwashers. For optimal washing results it is
important to use a good quality detergent.
•
The detergent packs must be sealed and stored in a dry place to prevent the formation of
lumps which may negatively affect washing results. Once opened the detergent packs should
not be kept for too long, otherwise the detergent loses its effectiveness.
•
Do not use detergents formulated for washing dishes by hand, because they produce a great
deal of foam and may negatively affect the operation of the dishwasher.
•
Add the correct amount of detergent. An insufficient amount of detergent will result in a partial
removal of dirt from the dishes, whereas an excessive amount is wasteful and does not
improve the washing results.
•
The market offers liquid and powder detergents with differing chemical compositions, which
may contain
phosphates
, or be phosphate-free but contain
natural enzymes
.
- Detergents containing
phosphates
are more effective against grease and starch at
temperatures above 60°C
.
-
Enzyme
detergents, on the other hand, are also effective at lower temperatures (
from 40 to
55°C
) and are more easily biodegradable. With enzyme detergents it is possible to obtain at
low temperatures comparable results to those which can only be achieved at
65°C
using
traditional detergents.
For the safeguarding of the environment we recommend the use of
phosphate- and chlorine
free
detergents.
•
Also available are tablet detergents which state that that no salt or rinse aid is required. In
some cases, these detergents might not give good results, especially with short and/or low-
temperature washing cycles.
If performance problems (e.g. a white coating on the tank or dishes, poor drying, dirt on dishes
at the end of the wash) are noted, users are advised to return to conventional products
(granular salt, powder detergent and liquid rinse aid).
However, please note that on return to the use of conventional salt, a number of cycles will be
required before the system becomes fully efficient again, so traces of white coating may still be
found on the tank and dishes. If the problem persists for too long, contact the After-Sales
Service.
•
When using detergent in tablet form (bear in mind that we recommend the use of three
separate products: detergent, salt and rinse aid), place the tablets in the cutlery rack. The
dispenser is designed to use powder or liquid detergent and the door does not open completely
during the washing cycle. This means that a tablet is not completely dissolved (released),
which may lead to the following:
-
not enough detergent released during the cycle, with poor washing results;
-
the detergent forms a solid block in the distributor and is released during the final rinse cycle.
The introduction of detergent into the rinse aid dispenser, even in liquid form, will damage
the dishwasher.
User instructions
38
4.3 General warnings and recommendations
Before using the dishwasher for the first time, it is advisable to read the following
recommendations concerning
dish types
to be washed and their
loading
.
There are generally no constraints on the washing of domestic dishes, but in certain cases it is
necessary to take their characteristics into account.
Before loading the dishes into the baskets it is necessary to:
•
remove coarse food remains: e.g. bones, fish-bones, etc. which may clog the filter or damage
the wash pump.
•
soak any pots or pans with burnt-on food remains on the bottom to facilitate removal, then
load them into the LOWER BASKET.
If washing only a small amount of dishes, use the
“half-load”
option to save on energy and water.
Remember to load only the basket selected for the half-load program: the other basket
must remain empty.
There is no need to pre-wash the dishes under running water before loading them into the baskets
since this only wastes water.
Correct loading of the dishes helps ensure optimal washing results.
WARNING!
•
Make sure that the dishes are securely in place so that they cannot tip over or obstruct the
rotation of the spray arms during the washing cycle.
•
Do not place very small objects in the baskets as these could fall and obstruct the spray arms
or the wash pump.
•
Containers such as cups, bowls, glasses and pots should always be loaded with the opening
facing downwards and with any cavities at an angle, to allow the water to drain out.
•
Do not stack dishes or place them in such a way that they cover one other.
•
Do not place glasses too close together because they may knock against each other and
break, or there might be staining at the point where they touch.
MAKE SURE that the items being washed are dishwasher-safe.
Items which are not dishwasher-safe:
• Wooden dishes, pots or pans:
these may be damaged by the high washing temperatures.
• Handcrafted items:
these are rarely suitable for washing in a dishwasher. The relatively high
water temperatures and the detergents used may damage them.
• Plastic di shes:
these are not heat resistant and may lose their shape. Heat resistant plastic
dishes must be washed in the upper basket.
• Dishes and objects in copper, tin, zinc or brass:
these tend to stain.
• Aluminium dishes:
items made from anodised aluminium may lose their colour.
• Silverware:
silver items may stain.
• Glass and crystal:
in general, glass and crystal objects can be washed in the dishwasher.
However, certain types of glass and crystal may become dull and lose their clearness after
many washings. Therefore, for these items we recommend using the least aggressive
program available.
• Decorated items:
the decorated objects available on the market are generally able to
withstand washing in the dishwasher, although the colours may fade after a great many
washes. If in doubt as to the fastness of the colours, it is advisable to wash just a few items at
a time for approximately one month.
User instructions
39
4.4 Using the baskets
The dishwasher has a capacity of
14 place-settings
, including serving dishes.
LOWER BASKET
The lower basket receives the full force of the lower spray arm, and should therefore be used for
the “toughest” items with a heavier degree of soiling. All types and combinations of loads are
permitted, provided that the dishes, pots and pans are arranged with all the soiled surfaces
exposed to the water jets coming from the bottom.
For optimum use of space, the bottom basket is fitted with two plate supports which can be laid flat
if there are no plates to be loaded. It also has a "tip-up support" (with one or two sectors depending
on models) for small plates; to take small plates, it must be positioned as shown in the illustrations.
LOADING THE LOWER BASKET
Carefully load flat plates, soup plates, dessert and serving dishes, positioning them vertically. Pots,
pans and their covers must be loaded upside down. When loading soup plates and dessert bowls,
be sure to leave a gap between them.
Loading examples:
User instructions
40
CUTLERY BASKET
The cutlery should be arranged in an orderly manner inside the basket, with the handles pointing
downwards. Take care during loading to avoid injury from the knife blades.
The basket is suitable for all types of cutlery, except those long enough to interfere with the upper
spray arm.
Ladles, wooden spoons and cooking knives can be placed in the upper basket,
making sure that
the knife blades do not protrude from the basket.
The cutlery basket features an
exclusive system
of independent
sliding tip-up supports
, offering
a series of combinations to allow optimum use of the space available. It can also be separated into
two parts, particularly useful when carrying out a
½ load wash
(on models with this function).
Vertical
inserts
Horizontal
insert
open
UPPER BASKET
It is recommended to load the upper basket with small- or medium-sized items such as glasses,
small plates, tea or coffee cups, shallow bowls and light objects made from heat resistant plastic. If
the upper basket is used in the lowermost position, it can also be loaded with serving dishes,
provided they are only slightly soiled.
The top basket is fitted (on the left) with two plastic racks
which can be raised to make room for tall glasses, such as
stem glasses.
On the right there are two cutlery racks designed to take
knives and teaspoons; when not in use, they can be left
vertical, attached to the basket.
To use the space designed for teaspoons, remove the insert
as shown in the illustrations.
Horizontal
insert closed
Movement required
to extract the inserts
User instructions
41
LOADING THE UPPER BASKET
Load the dishes with the top side facing forwards; cups and concave containers should always be
loaded with the opening facing down. The left side of the basket can be loaded with cups and
glasses on two levels. In the centre section, plates and saucers can be loaded vertically into the
supports provided.
Loading examples:
ADJUSTING THE UPPER BASKET
The upper basket can be adjusted in
two positions
, according to the user’s needs and according
to the height of the dishes in the lower basket. Proceed as follows
Pull-out
version:
•
pull out the right-hand basket guide;
•
remove the stop, first releasing it as shown in the diagram;
•
push the guide to free the wheels;
•
fit the upper or lower pair of wheels into the guide, depending on the setting required;
•
return the stop to its original position.
Push-button
version:
•
pull out the basket to its limit position and pull the right side upwards.
At this point it is possible to load larger sized plates into the lower basket.
•
To return to the original position, pull out the upper basket again and press the release lever.
User instructions
42
5. Cleaning and maintenance
Before carrying out any work, always disconnect the appliance from the electrical power
supply.
5.1 General warnings and recommendations
Avoid the use of acidic or abrasive detergents.
Clean the outer surfaces and door-lining of the dishwasher regularly using a soft cloth moistened
with water or with a normal detergent suitable for painted surfaces.
Clean the door gaskets with a damp sponge.
Periodically (once or twice a year) it is advisable to clean the tank and gaskets, using a soft cloth
and water to remove any deposits.
CLEANING THE WATER INT AKE FILTER
The water intake filter
A
located at the outlet of the water supply tap needs to be cleaned
periodically.
After having closed the water supply tap, unscrew the end of the water intake hose, remove the
filter
A
and clean it delicately under running water. Reassemble filter
A
in its seat and carefully
screw the water intake hose back into position.
CLEANING THE SPRAY ARMS
The spray arms can be easily removed for periodic cleaning of the nozzles, to prevent possible
clogging. Wash them under running water and carefully replace them in their seats,
checking that
their rotary movement is in no way impeded
.
•
To remove the
upper
spray arm, unscrew locking ring
R
.
•
To remove the
lower
spray arm, simply lift it up, pulling by the central part.
CLEANING THE ORBITAL VERSION SPRAY ARM
To remove the ORBITAL spray arm assembly, take hold of the
longer arm and pull the ORBITAL unit upward.
Wash the arms under a jet of running water and return them
carefully to their seat.
After reassembly, check that the spray arms turn freely.
Otherwise, check that they have been installed correctly.
ORBITAL
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
Smeg DWF614WH is an efficient dishwasher that will meet the expectations even of the most demanding users. It is equipped with a water softening system, rinse aid and detergent dispensers, and an array of washing programs, so you can be sure that your dishes will always come out sparkling clean. The dishwasher also features a user-friendly front panel and information display, making it easy to operate. Additionally, the dishwasher has a spacious interior with adjustable baskets, allowing you to fit even large pots and pans inside.
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
Other documents
-
Whirlpool GMX 51405 User guide
-
Whirlpool WP 3900 LP User guide
-
-
KitchenAid KDSXS 82131 User guide
-
Gorenje GI64324X Operating instructions
-
-
Whirlpool GMX 50205 Owner's manual
-
Teka DW8 60 FI User manual
-
Gorenje Dishwasher User Instructions
-
CDA VW80 User manual