Bauknecht HDW 6000 Program Chart

Category
Washing machines
Type
Program Chart
GB HDW 6000 PROGRAMME CHART
5019 401 05379
1)
For improved garment care spin speed is restricted to 1000 rpm in this programme.
2)
For improved garment care spin speed is restricted to 400 rpm in this programme.
Programme
Care
Labels
Type of wash/
Degree of soiling
Max.
load
kg
Detergent and Additives
Selectable Special Options =
Tempe-
rature
°C
Max.
Spin
speed
rpm
Notes
Softe-
ner
Main
wash
Pre-
wash
Start
Delay
Start
Delay
Eco
Eco
Pre-
wash
Pre-
lavaggio
Intensive
Rinse
Risciacquo
Intensivo
Rinse
hold
Anti
piega
Speed
reduction
Centrifuga
Cotton
Cotone
Normally to heavily soiled bed linen,
table linen and underwear, towels, shirts etc. made of
cotton and linen.
For temperature selection, respect the manufacturer's
recommendations on the care label.
6.0
Yes
❉❉
30-40
60-95
1200
“Prewash” can be additionally selected
for heavily soiled laundry at any
temperature.
Synthetic
Sintetici
Normally soiled blouses, shirts and other outer clothing
made of polyester (Diolen, Trevira), polyamide (Perlon,
Nylon) or mixtures of these fibres with cotton.
For temperature selection, respect the manufacturer's
recommendations on the care label.
2.5
Yes
❉❉
1)
30-40-60 1000
1)
“Prewash” can be additionally selected
for heavily soiled laundry.
Daily mixed
Misti
Slightly to normally soiled textiles made of cotton and/or
synthetic fibres.
For temperature selection, respect the manufacturer's
recommendations on the care label.
3.0
Yes
––
❉❉❉
40-60 1200
In this programme the spin speed should
be adapted to the fabrics.
Rapid wash
Rapido 30’
Hardly worn outer and sports clothing made of cotton,
polyester, polyamid and mixed cotton fabrics.
3.0
Yes
––
❉❉
30 1200
Delicate
Delicati
Curtains and delicate dresses, skirts, shirts and blouses.
1.5
Yes
❉❉
❉❉
1)
30-40 1000
1)
Wool
Lana
Only woollens with a felt-free finish, labelled with the
woolmark and identified as machine washable.
1.0
Yes
––
❉❉
1)
cold
30-40
1000
1)
If you select “Rinse hold” do not leave
items to soak for too long.
Handwash
Lavaggio a mano
Textiles made of linen, silk, wool or viscose marked as
“handwashable”.
This cycle is particularly suitable to treat delicate lingerie
(use of a laundry net strongly recommended).
1.0
Yes
––
❉❉
2)
30 400
2)
If you select “Rinse hold” do not leave
items to soak for too long. A very gentle
spin is used in this programme.
Rinse & Spin
Risciacquo & Centrifuga
––
6.0
––
––
❉❉❉
20 1200
Same as the spin cycle in the “Cotton
programme.
Spin
Centrifuga
––
6.0
––
––
1200
In this programme spinning is intensive.
Same as the spin cycle in the “Cotton
programme.
Short Spin
Centrifuga breve
––
1.5
––
––
1)
1000
1)
A very gentle spin is used in this
programme. Same as the spin cycle in the
“Wool” programme.
Drain
Scarico acqua
––
––
This programme only drains (alternative
method of terminating the programme
after “Rinse hold” without spinning). In
addition all running programmes can be
cancelled with this programme.
F
I
D
D
{
G H
This washing machine is equipped
with
automatic safety functions
which detect
and diagnose faults at an early stage and react
appropriately, e.g.:
A. “Pump” indicator
B. “Water tap closed” indicator
Check your washing machine’s water supply.
C. “Waterstop” indicator
D. “Door locked” indicator
As long as a washing programme is running,
the lamp lights up to show that the door
cannot be opened.
E. “Start” button
F. Start Delay
G. Programme sequence indicator
H. Spin Speed reduction button
I. Reset button
J. Selectable programmes
E
A
C
B
40105379GB.fm Page 1 Wednesday, February 7, 2007 5:55 PM
Black process 45.0° 100.0 LPI
5019 401 05379
Add the detergent as described in the chapter
“Detergent and Additives” in the instructions for use.
Turn
the
programme selector knob
in any
direction to the desired programme.
The light above the
“Start”
button flashes.
The
programme sequence indicator
and the
indicator with the maximum possible spin speed
light up.
Wash your laundry in the desired programme
(Cotton, Synthetics), adding an appropriate
amount of chlorine bleach to the SOFTENER
chamber (close the detergent dispenser carefully).
Immediately after end of programme, start the
“Rinse and Spin” programme to eliminate any
residual bleach smell; if you want, you can add
softener.
“Eco” button
With a modified temperature profile and a
slightly prolonged washing duration, the
optimum combination of excellent washing
result and even lower energy consumption can
be achieved.
“Prewash” button
Only for heavily soiled laundry (e.g. sand or
granular dirt). Programme duration is increased
by some 15 min.
“Intensive Rinse” button
An additional rinse cycle is carried out.
This option is particularly suitable for areas with
very soft water, washing baby linen and helps
people with detergent allergies.
“Rinse Hold” button
The laundry remains in the last rinse water
without being spun: discoloration of the laundry
and additional creasing are prevented.
This option is particularly recommended for the
programme “Synthetic” or “Delicate”.
This function is particularly useful if you want to
postpone spinning to a later time.
Note:
The programme has reached the “Rinse
Hold” when the corresponding light flashes.
Terminate the “Rinse Hold” option:
Press the “Rinse Hold” button again; the
programme will terminate automatically with the
appropriate spin cycle for the current programme.
If you do not wish to spin the clothes, turn the
programme selector knob to “Drain” and press
the
“Start”
button again.
“Spin speed” button
A maximum spin speed is assigned to each
programme.
Press the button to set another speed for the
spin cycle.
If no light goes on, the final spin is cancelled.
The water is only drained out.
CONSUMPTION DATA
*
Programme Temp erature
(°C)
Wash
(kg)
Water
(l)
Energy
(kWh)
Programme duration
approx.**
(hours : minutes)
Cotton
95 6.0 54
***
1.90 2:00
Cotton
60 6.0 49 1.14 2:20
Cotton with “Eco” ****
60 6.0 49 1.02 2:30
Cotton
40 5.0 47 0.70 2:05
Synthetic
60 2.5 60
***
0.90 1:45
Synthetic
40 2.5 55 0.60 1:30
Daily mixed
40 3.0 48 0.55 1:00
Rapid wash
30 3.0 37 0.30 0:30
Delicate
30 1.5 60 0.50 0:45
Wool
40 1.0 60 0.50 0:40
Handwash
30 1.0 45 0.40 0:35
*
The
consumption values
were measured in normalized conditions in compliance with Standard IEC/EN 60456.
**
The
programme duration
may also vary from the chart values. The washing machine is able to allow for particular
household conditions and to adapt the programme run time accordingly.
***
To reduce the
water temperature
, some cold water is added at the end of the main wash cycle, before the pump
drains the water out.
****
Reference programme for energy label.
POUR IN DETERGENT, CLOSE THE DOOR
AND SELECT A PROGRAMME
USING CHLORINE BLEACH
SELECT SPECIAL OPTIONS - The
corresponding lights go on (if not selectable:
rapid flashing for 3 seconds)
With the “Start Delay” function the appliance can be run
cheaply e.g. at night, when the electricity is cheaper.
Press the “Start Delay” button. Select the
programme start from 3 to 12 hours ahead by
pressing the button again.
Press the
“Start”
button.
The Start Delay indicator light flashes until the
programme starts.
“Start Delay” correction.
Before the “Start Delay” has been started:
The preset number of hours can be altered by
continuously pressing the “Start Delay” button.
By pressing the Start Delay button again after the
“12” setting, the time delay can be deleted again
or set again.
After the “Start Delay” has been started:
The preset number of hours can be reduced by
pressing the “Start Delay” button again; please
note, however, that the washing programme
starts IMMEDIATELY, as soon as you activate it
again with the Start Delay switch 3 setting. To
increase the number of hours preselected, first
turn the programme selector switch to the “Off
position. Then set the programme and the
additional options again and select the desired
number of hours.
After you have selected the programme and the
additional option, the indicator light over the
“Start”
button flashes. Turn on the tap and start
the programme by pressing the
“Start”
button.
Now the indicator light above the button goes on.
In addition, all programme phases are indicated by the
associated lights. After the end of a programme phase,
the associated indicator light goes out. Thus the
programme sequence indicator moves from left to
right across the wash, rinse and spin phases. At the end
of the programme, only the “End” indicator is still on.
As long as a washing programme is running, the
lamp lights up to show that the door cannot be
opened. When the lamp goes off, the door can be
opened again.
If
“Start”
has been pressed, but the door is not
latched, the “Door Locked” indicator flashes for 10
seconds. The door must be pushed shut within this
time. After the 10 seconds, the “Door Locked”
indicator goes out and the
“Start”
button flashes.
The door must then be opened and closed again and
the
“Start”
button must be pressed.
“Pump”
Waste water is not pumped out. Check wether the
drain hose is kinked or the filter must be cleaned; in
the latter case refer to the Instructions for Use
(“Removing the Filter”).
“Water tap closed”
The appliance has no or insufficient water supply.
Open the water tap; if the indication still lights up,
refer to the “Troubleshooting Guide” in the
Instructions for Use.
“Waterstop“
Lighting up of the Aquastop indication can be caused
by a leak in the appliance or hose. Please refer to the
“Troubleshooting Guide” in the Instructions for Use.
The “End” indicator goes on.
1. Set the programme selector knob to the
“Off” position.
2. Turn off the tap.
3. Open the door and unload the machine.
A newly-selected programme will continue in the
same programme section during which the current
programme was interrupted. Therefore do not add
any more detergent.
1. Press the
“Start”
button to interrupt the
programme. The light flashes.
2. Select the new programme (with temperature),
any additional options and - if you wish - another
spin speed.
3. Press the
“Start”
button again to restart the
programme.
If you are in the “Prewash” programme step, this
additional option cannot be deselected as
described (to do this see “Cancel (Reset) a
running programme before the end”).
Press the
“Reset”
button for at least 2 seconds.
Any existing water is drained out before the door
can be opened.
START DELAY
PROGRAMME START
“DOOR LOCKED” INDICATOR
“TROUBLE” INDICATORS
PROGRAMME END
RESELECT AFTER PROGRAMME START
CANCEL (RESET) A RUNNING
PROGRAMME BEFORE THE END
40105379GB.fm Page 2 Wednesday, February 7, 2007 5:55 PM
Black process 45.0° 100.0 LPI
  • Page 1 1
  • Page 2 2

Bauknecht HDW 6000 Program Chart

Category
Washing machines
Type
Program Chart

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI