Creative Playthings 50545-555 User manual

Brand: Creative Playthings

Model: 50545-555

Type: User manual

Creative Playthings 50545-555 Glider Bracket Pack is designed for use with Premium Pine and Classic Pine swing beams. It contains all the necessary hardware for easy installation, including glider brackets, bolts, washers, and nuts. The glider brackets are made of high-quality materials and are specially coated for corrosion resistance. The pack also includes detailed assembly instructions with diagrams for proper installation. With the Creative Playthings 50545-555 Glider Bracket Pack, you can easily add a glider to your swing set and provide your kids with hours of fun and entertainment.

 4 14186-400 GliderBracket

  

 8 12002-207 FlatWasher,3/8"

 4 12017-207 LockWasher,3/8"

 4 17003-1413 HexBolt,3/8x3-1/2"

 4 17003-1813 HexBolt,3/8x4-1/2"

 4 12052-107 NylockNut,3/8"

 8 12002-206 FlatWasher,5/16"

 8 17036-602 LagScrew,5/16x1-1/2"























HexBolt3/8x4-1/2"

HexBolt3/8x3-1/2"

LagScrew5/16x1-1/2"

FlatWasher3/8"

LockNut3/8"LockWasher3/8"

FlatWasher5/16"



Ifthisisanewinstallation,donotinstallthepair

of Swing Hangers closest to the Legs of the

SwingBeam.IftheSwingHangersarealready

installed,removethem.

Find the two pair of Bolts above the Swing

Hanger positions nearest the Legs. Remove

thefourHexBoltsandassociatedwashersand

weldnuts.

Seeinstructionforthegym

towhichtheSwingBeamis

mountedforspecialsafety

informationregardingrequired

space,resilientgroundcover,

etc.

ThispackageisforusewithPremiumPineand

ClassicPineswingbeams.ThePremiumPine

beamisshownintheillustrations.

GliderBrackets

RemoveBolts



©Copyright2014,CreativePlaythings.PrintedinU.S.A.

19919-100RevA(09-14)

GliderBracketPack





Ononesideofthebeam,alignthetopholes

of a Glider Bracket with two of the holes

where Bolts were removed in the previous

step.Markthepositionofthelowerholesof

theGliderBracketontheBeam.Dothesame

withanotherGliderBracketandtheotherpair

ofholes.

Drill 3/16" diameter holes 1-1/2" into the

Beamatthemarks.

TurntheBeamover.Markanddrillthebeam

inthesamemanner.



FastentheGlidersBracketstotheBeamAs-

sembly using two 3/8 x 4-1/2" Hex Bolts*,

four3/8FlatWashers,andtwoNylockNuts

foreachpairofBrackets,intheupperholes

asshown.Useone5/16x1-1/2"LagScrew

with one 5/16 Flat Washer for each of the

eightremaininglowerholes.

*Use3/8x3-1/2"BoltsfortheClassicPine

Beam.



HangtheBack-to-BackGliderbyhookingthe

chaininthesnaphooksontheGliderHang-

ers.Followthespecialassemblyinstructions

includedfortheBack-to-BackGlider.

U.S. safety standards require a minimum

clearance of 8" from the bottom of each

SwingAccessorytotheground.U.K.(&E.U.)

safety standards require a minimum clear-

anceof350mm(13-3/4")betweenthebottom

ofeachSwingAccessoryandtheground.

The height of each SwingAccessory is ad-

justed byusing a different linkin the chain.

BesuretohangtheSwingsAccessorieswith

groundclearancegreaterthanorequaltothe

safetystandardforyourregion.

Drill3/16"

Dia.Holes

Creative Playthings 50545-555 User manual

Creative Playthings 50545-555 User manual

Creative Playthings 50545-555 User manual

Other documents