2. HARVIA
  3. SASS018

HARVIA SASS018, SASS016, SASS017 Installation guide

  • Hello! I've reviewed the Harvia BLOCK installation instructions and I'm ready to assist you with any questions about installing your benches. The document covers a wide range of installation details, from setting bench heights to installing supportive legs, bench decks, skirts, backrests, footrests and lighting. Feel free to ask me any questions you have and I will help you.
  • How far below the bench deck top is the bench frame?
    What should be used to fill gaps when installing the bench frame?
    When is bench support needed for a lower bench?
    Where should the wires of LED-lights be installed?
Installation instructions
1
Y05-1173
HARVIA BLOCK- manual
EN
Installation instructions
2
Y05-1173
Necessary tools and symbols
BLOCK BENCH MODELS
EXTEND
BOX
AIR
Installation instructions
3
Y05-1173
VONTENT:
BENCH HEIGHTS 4
INSTALLATION OF BENCH FRAMES 4
INSTALLTION OF LOWER BENCH 5
SUPPORTING OF BENCHES 7
BENCH SKIRTS 8
BENCH DECKS 8
BACK RESTS 9
FOOTREST 10
STOOLS 11
CORNER BENCHES 11
BENCH FRAMES 12
SUPPORTIVE LEGS 13
LOWER BENCHES 13
BENCH SKIRTS 14
BENCH DECKS 14
BACK RESTS 15
FOOTREST 16
ROUNDING OF BENCH 17
ROUNDING OF BENCH SKIRT 18
ROUNDING OF BACK REST 19
DECORATIVE BENCH END 20
ARM REST 21
LED-LIGHTS 22
Installation instructions
4
Y05-1173
BENCH HEIGHTS
Check bench heights from offer. Measure and mark level of upper bench frames. Notice, that bench frame is
28mm below bench deck top! Install upper benches onto frames behind wall panels.
INSTALLATION OF BENCH FRAMES
Measure the distance between bench frames and side walls. Fill up the gap with plywood pieces (4mm / 6mm).
Screw bench frame onto frames behind panels.
Zn 6*120mm
Installation instructions
5
Y05-1173
Install upper bench frame also from side. Remember to use plywood pieces in the middle!
INSTALLATION OF LOWER BWNCH
Measure and mark place of the lower bench. Check right position from the offer or in the picture below, which is
showing the right position of lower bench relating upper bench.
Zn 6*120mm
Zn 6*120mm
Installation instructions
6
Y05-1173
NOTICE! In AIR-model lower bench starts from the back wall.
BOX
AIR
Depth position of lower bench
must be measured from upper
bench!
Zn 6*120mm
Installation instructions
7
Y05-1173
SUPPPORTING A BENCH
IF width of lower bench is over 1600mm, bench support is needed.
IF width of bench < 1800, install supportive leg for lower bench as in picture ABOVE.
IF width of lower bench > 1800, install supportive leg for BOTH of benches as in picture BELOW.
BLOCK AIR ->
IF width of lower bench is over 1800mm, bench support is needed.
Install supportive leg from behind of bench frame.
5*100mm
5*100mm
5*80mm
X*XXmm
BOX
EXTEND
5*80mm
EXTEND
4,5*50mm
4,5*50mm
Installation instructions
8
Y05-1173
BENCH SKIRTS
Install bench skirts behind front board of upper bench frame.
BENCH DECKS
EXTEND
4,5*45mm
4,5*45mm
EXTEND
BOX
BOX
Installation instructions
9
Y05-1173
BENCH DECKS (AIR)
suos
BACK RESTS
Big bench decks are made of several pieces to ease
installation and cleaning.
Picture indicates recommended
height of back rest according to upper
bench. Measure, predrill and install.
Wires of LED-lights are recommended
to be installed behind wall boards.
4,5*45mm
TIP! You can choose height of back rests also
according to user.
Installation instructions
10
Y05-1173
FOOTREST
Place footrest on place and mark with pen. Mark places of screws with rubber washers and drill screw holes
through deck boards. Place footrest onto rubber washers (2 layers) and screw underneath deck.
4,5*45mm
Installation instructions
11
Y05-1173
STOOLS
Stools are preassembled.
CORNER BENCHES
Installation instructions
12
Y05-1173
BENCH FRAMES
Install upper benches onto frames behind panels.
Mount benches together from two directions!
5*80mm
Zn 6*120mm
Installation instructions
13
Y05-1173
SUPPORTIVE LEG
Install supportive leg into joint of benches. Lower bench will also be supported with supportive leg.
LOWER BENCHES
Install first bench onto wall and onto supportive leg. Mount benches together from two directions!
4,5*45mm
5*80mm
Installation instructions
14
Y05-1173
BENCH SKIRTS
Install bench skirts behind front board of upper bench frame.
BENCH DECKS
4,5*45mm
4,5*45mm
Lift and turn decks carefully
on places. Right position is
marked in every deck.
Installation instructions
15
Y05-1173
BACK RESTS
TIP! You can choose height of back rests also according to user.
Picture indicates recommended height of
back rest according to upper bench.
Measure, predrill and install.
Wires of LED-lights are
recommended to be
installed behind wall boards.
4,5*45mm
Installation instructions
16
Y05-1173
FOOT REST
4,5*45mm
Place footrest on place and
mark with pen. Mark places of
screws with rubber washers
and drill screw holes through
deck boards. Place footrest
onto rubber washers (2 layers)
and screw underneath deck.
Installation instructions
17
Y05-1173
ROUNDING OF BENCH
4,5*60mm
Installation instructions
18
Y05-1173
ROUNDING OF BENCH SKIRT
4,5*45mm
Installation as bench skirst.
Look page 13.
Installation instructions
19
Y05-1173
ROUNDING OF BACK REST
4,5*45mm
Installation as back rest. Look page 14.
Installation instructions
20
Y05-1173
DECORATIVE BENCH END
4,5*45mm
/